dimo User Guide Preparation Power ON/OFF
* Press the power button; the LED light will be turned on in 1 second.
* When the pen is on, press the power button for 2 seconds, the LED light will start flashing and the pen will turn off.
* If there is no action taken for more than 10 minutes, the pen will turn off automatically.
(You can change the auto-power-off time in settings. Using a longer auto-power-off time will result in shorter usage time if the pen is frequently idle). Holding the Pen
* The recognition rate is affected by the direction of the optical sensors angle. The sensor (oval shaped part adjacent to the pen tip) should face downwards.Deviating from the appropriate degree, or holding the pen in the wrong direction could cause difficulties with capturing your writing or drawing.
# Reset Please reset the pen if it does not turn off, won't charge, or stops working. To reset the pen to factory defaults, press and hold the power button for 10 seconds, the pen will be turned off and restart. (Internal data will be saved.) Usage Angle Hold the pen and maintain a natural writing angle. Allowable Recognition Angle Products acceptable recognition angle is
-20 ~ +40.
(90 vertical standard) LED Color Status Key Status Power ON Power OFF Low battery power During App connection Low storage During firmware update Firmware update failure Verify optical sensor or usage environment Changing ink color after connecting to the App
-
-
-
(1)Flashing
-
LED Color Solid
-
-
-
Flashing Solid Flashing
(1)Dimming Flashing Solid (with alarms) Change color dimming(1)
(1)Dimming : Indicates slowly getting dark and bright while flashing.
(2)Check if theres any dirt around optical sensor or on paper. Precautions Direct sunlight may cause the loss of recognition of writing. Please be careful not to cover the optical sensor with your fingers. Otherwise, your writing may not be recognized. Do not apply pressure to the pen tip. Storing pen without pen cap may cause degradation of functionality due to dust and foreign substances on the optical sensor. The pen cap should be placed on the pen if not in use and if the cap gets dirty, please clean with soft cloth or cotton swab. If you use a non-recommended ink refill, it may cause a recognition problem. NeoLAB is not responsible for any malfunction caused by this matter. If you write on the edge of the page where there is no code, your handwriting may not be recognized. Installation Downloading the App Please activate Bluetooth on the smart device. Run the downloaded NEO NOTESTM. NEO NOTESTM The app can be downloaded from Google play, Apple app store or Microsoft store. Please search for NEO NOTES, Neo smartpen in the search bar to find the app. Experience your Neo smartpen on the page, practice writing below. FCC Information to User This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:
Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. Caution Modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. IMPORTANT NOTE : FCC RF Radiation Exposure Statement This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 0.5 centimeters between the radiator and your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. NOTE : THE GRANTEE IS NOT RESPONSIBLE FOR ANY CHANGES OR MODIFICATIONS NOT EXPRESSLY APPROVED BY THE PARTY RESPONSIBLE FOR COMPLIANCE. SUCH MODIFICATIONS COULD VOID THE USERS AUTHORITY TO OPERATE THE EQUIPMENT. THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS: (1)THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE, AND (2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION. IC Information to User This device complies with Industry Canadas licence-exempt RSSs. Operation is subject to the following two conditions:
(1) This device may not cause interference; and (2) This device must accept any interfer-ence, including interference that may cause undesired operation of the device Le prsent appareil est conforme aux CNR dIndustrie Canada applicables aux appareils radio exempts de licence. Lexploitation est autorise aux deux conditions suivantes : (1) lappareil ne doit pas produire de brouillage, et
(2) lutilisateur de lappareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible den compromettre le fonctionnement.