FCC ID: PY314100251 Universal WiFi Range Extender

WN3000RPv2 WiFi Range Extender User Manual January 2014 202-XXXXX-01 350 East Plumeria Drive San Jose, CA 95134 USA WN3000RPv2 WiFi Range Extender Support Thank you for selecting NETGEAR products. After installing your device, locate the serial number on the label of your product and use it to register your product at https://my.netgear.com. You must register your product before you can use NETGEAR telephone support. NETGEAR recommends registering your product through the NETGEAR website. For product updates and web support, visit http://support.netgear.com. Phone (US & Canada only): 1-888-NETGEAR. Phone (Other Countries): Check the list of phone numbers at http://support.netgear.com/general/contact/default.aspx. Compliance For regulatory compliance information, visit http://www.netgear.com/about/regulatory. Trademarks NETGEAR, the NETGEAR logo, and Connect with Innovation are trademarks and/or registered trademarks of NETGEAR, Inc. and/or its subsidiaries in the United States and/or other countries. Information is subject to change without notice. NETGEAR, Inc. All rights reserved. 2 WN3000RPv2 WiFi Range Extender Contents Chapter 1 Get to Know Your Extender Front Panel . 6 Extender Side and Bottom Panels . 7 How the Extender Works . 7 When to Use Your Extender . 8 Chapter 2 Install Your Extender Place the Extender . 10 Find the Best Location . 13 Extender Performance . 14 Cable a Computer or Device to the Ethernet Port . 14 Chapter 3 Manage the Extender Network and Settings Log In to the Extender After Initial Setup . 17 Change the admin Password . 17 Set Up Password Recovery for admin . 18 Use the Smart Setup to Connect the Extender to a Network . 19 Use the WPS Wizard for WiFi Connections . 21 View or Change Advanced Wireless Settings . 22 View or Change the WPS Settings . 23 Set Up a Wireless Access List. 24 Manage Profiles . 26 Chapter 4 Monitor and Maintain the Extender Recover the admin Password. 29 Back Up the Extender Configuration . 29 Restore Saved Configuration Settings . 30 Return the Extender to Its Factory Settings . 31 Use the Factory Reset Button to Restore Factory Settings . 31 Erase the Extender Settings and Return to Factory Settings . 32 Update the Firmware . 33 View Wired and Wireless Network Devices. 34 Chapter 5 FAQs and Troubleshooting FAQs. 36 Cannot Log In to the Extender . 37 Cannot Join the Extender WiFi Network . 37 3 WN3000RPv2 WiFi Range Extender Appendix A Supplemental Information Factory Default Settings . 40 Technical Specifications . 40 4 1. Get to Know Your Extender This chapter covers the following topics:

1 Front Panel Extender Side and Bottom Panels How the Extender Works NETGEAR recommends that you connect to the extender only when your WiFi network connection is poor. Data traffic routed through the extender is inherently slower than traffic routed directly from the network. When to Use Your Extender For more information about the topics covered in this manual, visit the support website at http://support.netgear.com. Firmware updates with new features and bug fixes are made available from time to time on downloadcenter.netgear.com. Some products can regularly check the site and download new firmware, or you can check for and download new firmware manually. If the features or behavior of your product do not match what is described in this guide, you might need to update your firmware. 5 WN3000RPv2 WiFi Range Extender Front Panel The front panel has LEDs. Router Arrow LED Client Arrow LED Router Link LED Power LED WPS LED Client Link LED Figure 1. Extender front panel Table 1. LEDs LED Description Router Link LED Client Link LED The connection between the extender and the router or access point. Solid green. Best connection. Solid amber. Good connection. Solid red. Poor connection. Off. No connection. The connection between the extender and a computer or mobile device. Solid green. Best connection. Solid amber. Good connection. Solid red. Poor connection. Off. No connection. Power LED WPS LED Solid amber. The extender is booting. Solid green. The extender is powered on. Off. The extender is powered off. Solid green. WiFi security is enabled (WPA or WPA2). Blinking green. A WPS connection is in progress. Off. WiFi security is not enabled. Router Arrow and Client Arrow If the Router Arrow or Client Arrow LED blinks, see Find the Best Location on page 13. If no arrow LEDs are lit, the extender is in a good location. Get to Know Your Extender 6 WN3000RPv2 WiFi Range Extender Extender Side and Bottom Panels The side panel has buttons, and the bottom panel has the Factory Reset button and an Ethernet port. Power On/Off button WPS button Factory Reset button Ethernet port Figure 2. Extender side and bottom panels How the Extender Works The extender increases the distance of a WiFi network. The extender connects to your networks WiFi signal and it broadcasts its own WiFi signal. When you are too far away to connect to your networks WiFi signal, you can connect to an extender WiFi signal instead. WiFi Range Extender Boosts the range of your existing WiFi and creates a stronger signal in hard-to-reach areas. Existing WiFi Sometimes your router does not provide the WiFi coverage you need. Figure 3. The extender WiFi signals reach areas outside of the range of your router Get to Know Your Extender 7 WN3000RPv2 WiFi Range Extender When to Use Your Extender NETGEAR recommends that you connect to the extender only when your WiFi network connection is poor. Data traffic routed through the extender is inherently slower than traffic routed directly from the network. Get to Know Your Extender 8 2. Install Your Extender This chapter covers the following topics:

Place the Extender Find the Best Location Extender Performance Cable a Computer or Device to the Ethernet Port 2 9 WN3000RPv2 WiFi Range Extender Place the Extender NETGEAR recommends that you place the extender near the router during initial setup. Then you can move it farther away from the router as needed to increase the area that has a WiFi signal. To place the extender 1. Place your extender in the same room as your WiFi router. 2. Plug the extender into an electrical outlet. The Power LED button. lights green. If the Power LED does not light, press the Power 3. Make sure that the switch on the extender is set to Extender. Connect to an Existing WiFi Network To extend the range of your WiFi network, you must connect the extender to your existing WiFi network. You can do this in one of two ways:

Connect with WPS. For more information, see Connect with WPS on page Connect with genie Smart Setup. For more information, see Connect with NETGEAR 10. genie Smart Setup on page 11. Connect with WPS Wi-Fi Protected Setup (WPS) lets you join a secure WiFi network without typing the network name and password. The WPS button is a physical button on the router or access point. WPS does not support WEP network security. If you are using WEP security, see Connect with NETGEAR genie Smart Setup on page 11. To connect with WPS:

1. Press the WPS button on the side panel of the extender. The WPS LED blinks. 2. Within two minutes, press the WPS button on your router or access point. The WPS LED on the extender lights solid green, the Router Link LED the extender is connected to your existing WiFi network. lights, and Note:

If the Router Link LED does not light, try again. If it still does not light, see Connect with NETGEAR genie Smart Setup on page 11. 3. If your WiFi router supports the 5 GHz band, repeat steps 1 and 2 to connect the extender to the 5 GHz band. 4. Find the new extender network name. Install Your Extender 10 WN3000RPv2 WiFi Range Extender The extenders wireless network name (SSID) changes to your existing WiFi network name, with _EXT at the end of the name. For example:

Existing WiFi network name. MyNetworkName New extended network name. MyNetworkName_EXT 5. Connect your existing WiFi devices to the new extended network. Use the same WiFi password that you use for your WiFi router. 6. Unplug the extender and move it to a new location closer to the area with a poor WiFi signal. The location that you choose must be within the range of your existing WiFi router network. 7. Plug the extender into an electrical outlet and wait one minute. lights green. If the Power LED does not light, press the Power The Power LED button. Use the Router Link LED on the front panel to help you choose a spot where the extender-to-router connection is optimal. Connect with NETGEAR genie Smart Setup You can use a web browser to connect to the extender and set it up. To connect with the browser-based Smart Setup:

1. Make sure that the switch on the extender is set to Extender. 2. Use a WiFi network manager on a computer or mobile device to find and connect to the extender WiFi network. After the connection with the computer or mobile device is established, the Client Link LED lights solid green. 3. Open a web browser window from the same computer or mobile device. The browser takes you directly to NETGEAR genie smart setup. Note:

If you are not automatically directed to NETGEAR genie, launch a web browser and enter www.mywifiext.net in the address field. Enter admin for the user name and password for the password. Install Your Extender 11 WN3000RPv2 WiFi Range Extender 4. Select a WiFi network to extend and click the Continue button. 5. Type the network password (also called passphrase or security key) in the Password field, and click the Continue button. 6. Select the Private Network or Public Network radio button, and click the Continue button. 7. Enter name (SSID) for your new extender WiFi network in the Name field and click the Continue button. Note: You can use the same security settings as your existing network by selecting the check box. The settings are applied and the following screen displays:

8. Use a WiFi network manager on the computer or mobile device to connect to the extenders newly created WiFi network. Install Your Extender 12 WN3000RPv2 WiFi Range Extender 9. Use your password to connect. 10. Select the check box and click the Continue button. 11. Unplug the extender and move it to a new location closer to the area with a poor WiFi signal. The location you choose must be within the range of your existing WiFi router network. 12. Plug the extender into an electrical outlet and wait one minute. The Power LED button. lights green. If the Power LED does not light, press the Power 13. Use the Router Link LED on the front panel to help you choose a spot where the extender-to-router connection is optimal. Find the Best Location If the WiFi signal is weak, the first time you join the extender network, an arrow LED blinks for two minutes. If this happens, adjust the position of the extender. No arrow LEDs are lit. The extender is in a good location. Left arrow blinks. Move the extender closer to the router. Right arrow blinks. Move the computer or mobile device closer to the extender. Install Your Extender 13 WN3000RPv2 WiFi Range Extender Extender Performance These extender LEDs indicate a WiFi connection:

WiFi signal between the router and the extender. WiFi signal between the extender and the computer or mobile device. The LEDs are color coded:

Green indicates the best connection. Amber indicates a good connection. Red indicates a poor connection. An LED that is off indicates no WiFi connection. Cable a Computer or Device to the Ethernet Port You can use an Ethernet cable to connect a computer or device to the Ethernet port on the extender. Here are some examples of when you might want to do this:

You want to use a computer to log in to the extender to view or change its settings, but you are having trouble connecting to the extender WiFi networks. You have already installed the extender and now you want to connect a device to the extenders Ethernet port. To cable a computer to the extender Ethernet port:

1. Install the extender so that it is connected to your existing network with a WiFi link. 2. Connect an Ethernet cable to the Ethernet port on the extender and to an Ethernet port on your computer. The computer connects to the extender. Your computer might display a message notifying you of an Ethernet connection. To cable a device to the extender Ethernet port:

1. Install the extender so that it is connected to your existing network with a WiFi link. Install Your Extender 14 WN3000RPv2 WiFi Range Extender 2. Connect an Ethernet cable to the Ethernet port on the extender and to an Ethernet port on your device. Extender Blu-ray player WiFi router The device connects to the extender. Now, the device can access your existing network through the extender. Install Your Extender 15 3. Manage the Extender Network and Settings 3 This chapter covers the following topics:

Log In to the Extender After Initial Setup Change the admin Password Set Up Password Recovery for admin Use the WPS Wizard for WiFi Connections View or Change Advanced Wireless Settings Set Up a Wireless Access List Manage Profiles The profile is removed from the list. 16 WN3000RPv2 WiFi Range Extender Log In to the Extender After Initial Setup After installation, you can log in to the extender to view or change its settings. To log in to the extender after the initial setup:

1. Connect a computer or mobile device to the extenders network. 2. Launch a web browser and enter www.mywifiext.net in the address field. A login screen displays. 3. Enter admin for the user name and password for the password. If your extender has an Internet connection, the extender automatically checks for new firmware at the NETGEAR website. The Status screen displays. Change the admin Password The user name to access the extender is admin, and its default password is password. NETGEAR strongly recommends that you set a more secure password. To change the password for the extender:

1. On your computer, launch a web browser. 2. In the address field of your browser, enter http://www.mywifiext.net. You are prompted to enter a user name and password. If you do not see the login prompt, make sure to include http:// when you type http://www.mywifiext.net in your browser. 3. Type admin for the user name and password for the password. Manage the Extender Network and Settings 17 WN3000RPv2 WiFi Range Extender If you already changed the password and want to change it again, type your personalized password. 4. Select Maintenance > Set Password. 5. (Optional) NETGEAR recommends that you select the Enable Password Recovery check box. This feature lets you recover the password if it is forgotten. Password recovery is supported in the Internet Explorer, Firefox, and Chrome browsers, but not in the Safari browser. If you enabled password recovery, select two security questions and provide answers to them. 6. 7. Type the old password. 8. Type the new password twice. 9. Click the Apply button. Your settings are saved. Set Up Password Recovery for admin NETGEAR recommends that you enable password recovery if you change the password for the router user name admin. Then you can recover the password if it is forgotten. This recovery process is supported in the Internet Explorer, Firefox, and Chrome browsers, but not in the Safari browser. To set up password recovery:

1. On your computer, launch a web browser. 2. In the address field of your browser, enter http://www.mywifiext.net. You are prompted to enter a user name and password. If you do not see the login prompt, make sure to include http:// when you type http://www.mywifiext.net in your browser. 3. Type admin for the user name and password for the password. Manage the Extender Network and Settings 18 WN3000RPv2 WiFi Range Extender If you already changed the password and want to change it again, type your personalized password. 4. Select Maintenance > Set Password. 5. Select the Enable Password Recovery check box. 6. Select two security questions and provide answers to them. 7. Click the Apply button. Your settings are saved. Use the Smart Setup to Connect the Extender to a Network The first time that you use a browser to connect to the extender to install it, the NETGEAR genie installation wizard displays. If you want to use a wizard to set up the extender again, you can log in to the extender and use the Smart Wizard. To use Smart Setup to connect the extender to a WiFi network:

1. On your computer, launch a web browser. 2. In the address field of your browser, enter http://www.mywifiext.net. You are prompted to enter a user name and password. If you do not see the login prompt, make sure to include http:// when you type http://www.mywifiext.net in your browser. 3. Type admin for the user name and password for the password. If you already changed the password, type your personalized password. Manage the Extender Network and Settings 19 WN3000RPv2 WiFi Range Extender 4. Select Smart Wizard. The Smart Wizard displays the switch setting on your extender. In this example, the switch is set to Extender, which is the right setting if you want your extender to use WiFi to connect to your network. The extender finds the 2.4 GHz wireless networks in your area and displays a list. 5. To select the network you want the extender to join, do one of the following:

Select the radio button for the network. Select the Manually input my wireless SSID radio button and type the name of the network. 6. Enter the security settings for the network that you selected. The extender finds the 5 GHz WiFi networks in your area and prompts you to select a 5 GHz WiFi network 7. If your router or gateway broadcasts a 5 GHz WiFi network, select it from the list. Otherwise, click the Skip button. Manage the Extender Network and Settings 20 WN3000RPv2 WiFi Range Extender The extender prompts you to specify whether the network is private or public. 8. Specify if the network that you selected is private or public:

If your network is private, leave the Private Network radio button selected. If you are connecting the extender to a public network, select the Public Network radio button. Selecting the Public Network radio button enables a firewall to protect your computer from others who are sharing this public network. 9. Click the Continue button. You are prompted to name the extender networks. By default, the extender network names are the same as the networks that you selected with _2GEXT and _5GEXT at the end. 10. Either change the names or leave them as they are, then click the Continue button. The settings are applied to the extender. Use the WPS Wizard for WiFi Connections The WPS Wizard helps you add a wireless computer or device to the extenders WiFi networks without typing the WiFi password. WPS does not support WEP network security. If you are using WEP security, see Connect with NETGEAR genie Smart Setup on page 11. Note: For instructions about how to use the physical WPS button on the extender, see Connect with WPS on page 10. To use the WPS Wizard:

1. Launch a web browser from a computer or wireless device that is connected to the network. Manage the Extender Network and Settings 21 WN3000RPv2 WiFi Range Extender 2. In the address field of your browser, enter http://www.mywifiext.net. A login screen displays. You are prompted to enter a user name and password. If you do not see the login prompt, make sure to include http:// when you type http://www.mywifiext.net in your browser. 3. Type admin for the user name and type your password. If you have not yet personalized your password, type password for the password. 4. Select ADVANCED > WPS Wizard. 5. Click the Next button. 6. Select the radio button for the setup method that you want to use:

Push button. Click the WPS button on this screen. PIN Number. The screen adjusts. Enter the client security PIN, and click the Next button. 7. Within two minutes, go to the client device and use its WPS software to connect to the WiFi network. The WPS process automatically sets up your wireless computer with the network password when it connects. The extender WPS screen displays a confirmation message. View or Change Advanced Wireless Settings Use care when changing the wireless settings. Incorrect settings might disable the extenders WiFi networks unexpectedly. To view or change the advanced wireless settings:

1. On your computer, launch a web browser. 2. In the address field of your browser, enter http://www.mywifiext.net. You are prompted to enter a user name and password. If you do not see the login prompt, make sure to include http:// when you type http://www.mywifiext.net in your browser. 3. Type admin for the user name and type your password. If you have not yet personalized your password, type password for the password. Manage the Extender Network and Settings 22 WN3000RPv2 WiFi Range Extender 4. Select Advanced > Wireless Settings. 5. All the check boxes are selected by default. In the Advanced Wireless Settings section of the screen, select or clear the check boxes. Enable Wireless Access Point (2.4 GHz). When this check box is selected, the extender allows WiFi connections in the 2.4 GHz band. Clearing this check box prevents wireless devices from connecting to the extender in the 2.4 GHz band. LAN devices can still connect to the extender over an Ethernet cable. Enable SSID Broadcast (2.4 GHz). When this check box is selected, the extender broadcasts its wireless network name (SSID) for the 2.4 GHz band. Clearing this check box hides the extenders 2.4 GHz network name. In such a situation, this network name does not display in a WiFi network manager. A user who wants to join this hidden network must know its network name. Enable 20/40 MHz Coexistence (2.4 GHz). The extender 2.4 GHz WiFi network can run in either 40 MHz mode or 20 MHz mode. When this check box is selected, the extender uses 40 MHz mode unless a nearby WiFi network is using 40 MHz mode. If that happens, the extender uses 20 MHz mode to coexist with that network. 6. Click the Apply button. View or Change the WPS Settings Use care when changing the wireless settings. Incorrect settings might disable the extenders WiFi networks unexpectedly. To view or change the advanced wireless settings:

1. On your computer, launch a web browser. 2. In the address field of your browser, enter http://www.mywifiext.net. You are prompted to enter a user name and password. If you do not see the login prompt, make sure to include http:// when you type http://www.mywifiext.net in your browser. Manage the Extender Network and Settings 23 WN3000RPv2 WiFi Range Extender 3. Type admin for the user name and type your password. If you have not yet personalized your password, type password for the password. 4. Select Advanced > Wireless Settings. 5. In the WPS Settings section of the screen displays the extenders PIN. You cannot change this number. In the WPS Settings section of the screen, change the settings as needed:

Enable Devices PIN. By default, this check box is selected so that it is possible to use the WPS PIN method to connect to the extenders network. To prevent PIN compromise... By default, this check box is selected. This feature lets you specify the maximum number of times someone can try to enter the extenders PIN to connect with WPS before the extender disables its PIN. Keep Existing Wireless Settings (2.4 GHz b/g/n). By default, this check box is selected so that the SSID and passphrase stay the same when you use WPS to connect to the 2.4 GHz band. NETGEAR recommends that you leave this check box selected. Keep Existing Wireless Settings (5 GHz a/n/ac). By default, this check box is selected so that the SSID and passphrase stay the same when you use WPS to connect to the 5 GHz band. NETGEAR recommends that you leave this check box selected. 6. Click the Apply button. Set Up a Wireless Access List By default, any wireless device that is configured with the correct network name (SSID) can access the extenders WiFi networks. For increased security, you can restrict access to the extenders WiFi networks so that only wireless devices with the MAC addresses that you add to an access list can connect. Manage the Extender Network and Settings 24 WN3000RPv2 WiFi Range Extender Each network device has a MAC address, which is a unique 12-character physical address, containing the hexadecimal characters 09, af, or AF only, and separated by colons (for example, 00:09:AB:CD:EF:01). Typically, the MAC address is on the label of the wireless device. If you do not have access to the label, you can display the MAC address using the network configuration utilities of the computer. You might also find the MAC addresses on the Network Devices screen (see View Wired and Wireless Network Devices on page 34). CAUTION:

If you use a wireless device to set up the access list, add your wireless device to the access list. Otherwise, you are disconnected when you click the Apply button. To avoid this situation, use a computer with a wired connection to access the extender. Before you enable the access list, you must add the MAC addresses of the wireless devices that you want to grant access to the WiFi network of the extender. To set up and enable the access list:

1. On your computer, launch a web browser. 2. In the address field of your browser, enter http://www.mywifiext.net. You are prompted to enter a user name and password. If you do not see the login prompt, make sure to include http:// when you type http://www.mywifiext.net in your browser. 3. Type admin for the user name and type your password. If you have not yet personalized your password, type password for the password. 4. Select Advanced > Wireless Settings and click the Setup Access List button. The Wireless Card Access List screen displays. 5. Click the Add button. The screen adjusts. Manage the Extender Network and Settings 25 WN3000RPv2 WiFi Range Extender In the Device Name field, type a name for the wireless device. In the MAC Address field, type the MAC address of the wireless device. 6. 7. 8. Click the Apply button. 9. Above the Wireless Card Access list, select the Turn Access Control On check box. 10. Click the Apply button. Now only computers and devices in the Wireless Card Access list can join the extenders WiFi networks. Manage Profiles Each time the extender connects to a new network, the extender automatically saves the wireless network connection settings in a profile. The first profile is named wifi_profile_001. If the extender connects to more networks, each new profile name is assigned in numerical order. Profiles are handy if you take your extender with you to use in more than one location, such as at home and at an office or hotel. You can edit the profile names and settings and you can delete profiles that you do not want. To edit a profile:

1. Connect a computer or mobile device to the extenders network. 2. Launch a web browser and enter www.mywifiext.net in the address field. A login screen displays. 3. Enter admin for the user name and password for the password. 4. Select Profile. The Profile List displays a profile for each wireless network that the extender has connected to. 5. Select the radio button for the profile. 6. Click the Edit button. 7. Change the details of the profile as needed. 8. Click the Apply button. Manage the Extender Network and Settings 26 WN3000RPv2 WiFi Range Extender To delete a profile:

1. Connect a computer or mobile device to the extenders network. 2. Launch a web browser and enter www.mywifiext.net in the address field. A login screen displays. 3. Enter admin for the user name and password for the password. 4. Select Profile. The Profile List displays a profile for each wireless network that the extender has connected to. 5. Select the radio button for the profile. 6. Click the Delete Profile button. The profile is removed from the list. Manage the Extender Network and Settings 27 4. Monitor and Maintain the Extender 4 This chapter covers the following topics:

Recover the admin Password Back Up the Extender Configuration Restore Saved Configuration Settings Return the Extender to Its Factory Settings Update the Firmware View Wired and Wireless Network Devices 28 WN3000RPv2 WiFi Range Extender Recover the admin Password If you have changed the password to access the extender and have set up password recovery, you can recover your password if you have lost it. For information about setting up password recovery, see Set Up Password Recovery for admin on page If you did not set up password recovery and have lost your password, you must reset the extender to factory default settings (see Return the Extender Configuration Settings to Factory Default Settings on page 63). 18. To recover your password to access the extender:

1. On your computer, launch a web browser. 2. In the address field of your browser, enter http://www.mywifiext.net. You are prompted to enter a user name and password. If you do not see the login prompt, make sure to include http:// when you type http://www.mywifiext.net in your browser. 3. Click Cancel. If password recovery is enabled, you are prompted to answer two security questions. 4. Enter the saved answers to the security questions. 5. Enter the serial number of your router. The serial number is on the routers label. Back Up the Extender Configuration When the extender works correctly after initial setup, NETGEAR recommends that you back up the extender configuration settings. After you have backed up the settings, if you change the extender settings but are not content with the new settings, you can restore the extender backed-up configuration settings. To back up the extender configuration settings:

1. On your computer, launch a web browser. 2. In the address field of your browser, enter http://www.mywifiext.net. You are prompted to enter a user name and password. If you do not see the login prompt, make sure to include http:// when you type http://www.mywifiext.net in your browser. 3. Type admin for the user name and type your password. If you have not yet personalized your password, type password for the password. Monitor and Maintain the Extender 29 WN3000RPv2 WiFi Range Extender 4. Select Maintenance > Backup Settings. 5. Click the Backup button. Your browser extracts the configuration file from the extender. If you do not have your browser set up to save downloaded files automatically, locate where you want to save the file. 6. Restore Saved Configuration Settings You can restore the configuration file of the extender to a previously saved configuration file. To restore the extender configuration settings:

1. On your computer, launch a web browser. 2. In the address field of your browser, enter http://www.mywifiext.net. You are prompted to enter a user name and password. If you do not see the login prompt, make sure to include http:// when you type http://www.mywifiext.net in your browser. 3. Type admin for the user name and type your password. If you have not yet personalized your password, type password for the password. 4. Select Maintenance > Backup Settings. 5. Click the Browse button. 6. Locate and select the previously saved backup file. By default, the name of the backup file is NETGEAR_EX6100.cfg. Monitor and Maintain the Extender 30 WN3000RPv2 WiFi Range Extender CAUTION:

After you click the Restore button, do not try to go online, turn off the extender, shut down the computer, or do anything else to the extender until it finishes restarting!

7. Click the Restore button. A confirmation pop-up screen displays. 8. Confirm your decision. The extender restarts. This process takes about one minute. Return the Extender to Its Factory Settings To reset the extender to factory default settings, you can use either the Factory Reset button or the Erase feature. For information about the factory settings, see Factory Default Settings on page 40. Use the Factory Reset Button to Restore Factory Settings CAUTION:

This process erases any settings that you have configured in the extender. To restore factory settings:

1. Insert a paper clip into the Factory Reset hole and hold it until the Power LED blinks amber. 2. Release the button. All the LEDs turn off for about three seconds. The Power LED lights solid amber for about 30 seconds. The Power LED lights solid green. The extender returns to its factory settings. When you plug in the extender, it detects the position of its Access Point/Extender switch. Factoy Reset button Monitor and Maintain the Extender 31 WN3000RPv2 WiFi Range Extender Erase the Extender Settings and Return to Factory Settings CAUTION:

This process erases any settings that you have configured in the extender. To erase the extenders current settings:

1. On your computer, launch a web browser. 2. In the address field of your browser, enter http://www.mywifiext.net. You are prompted to enter a user name and password. If you do not see the login prompt, make sure to include http:// when you type http://www.mywifiext.net in your browser. 3. Type admin for the user name and type your password. If you have not yet personalized your password, type password for the password. 4. Select Maintenance > Backup Settings. CAUTION:

After you click the Erase button, do not try to go online, turn off the extender, shut down the computer, or do anything else to the extender until it finishes restarting!

5. Click the Erase button. A confirmation pop-up screen displays. 6. Confirm your decision. The extender restarts. This process takes about one minute. Monitor and Maintain the Extender 32 WN3000RPv2 WiFi Range Extender Update the Firmware Unless you changed the settings in the Firmware Upgrade screen previously, the extender is set up to check for new firmware automatically when you log in. You can also check for new firmware. To check if new firmware is available and update the firmware:

1. On your computer, launch a web browser. 2. In the address field of your browser, enter http://www.mywifiext.net. You are prompted to enter a user name and password. If you do not see the login prompt, make sure to include http:// when you type http://www.mywifiext.net in your browser. 3. Type admin for the user name and type your password. If you have not yet personalized your password, type password for the password. 4. Select Maintenance > Firmware Update. 5. Click the Check button. 6. If new firmware is available, follow the onscreen prompts to download it onto your computer. Note: You might need to unzip the firmware file. 7. Click the Browse button. 8. Locate and select the new firmware file. CAUTION:

After you click the Upload button, do not try to go online, turn off the extender, shut down the computer, or do anything else to the extender until it finishes restarting!

9. Click the Upload button. The firmware update starts and the extender restarts. This process takes a couple of minutes Monitor and Maintain the Extender 33 WN3000RPv2 WiFi Range Extender View Wired and Wireless Network Devices You can view the active wired and wireless devices in both the network to which the extender is connected and the extender network. If you do not recognize a wireless device, it might be an intruder. To view devices on the network:

1. On your computer, launch a web browser. 2. In the address field of your browser, enter http://www.mywifiext.net. You are prompted to enter a user name and password. If you do not see the login prompt, make sure to include http:// when you type http://www.mywifiext.net in your browser. 3. Type admin for the user name and type your password. If you have not yet personalized your password, type password for the password. 4. Select Maintenance > Attached Devices. For each wired and wireless device, the IP address, device name, and MAC address display. 5. (Optional) Click the Refresh button. The information on the screen is updated. Monitor and Maintain the Extender 34 5. FAQs and Troubleshooting This chapter covers the following topics:

FAQs Cannot Log In to the Extender Cannot Join the Extender WiFi Network 5 35 WN3000RPv2 WiFi Range Extender FAQs This section provides answers for difficulties you might experience with the extender. 1. Question. Will the extender work if I connect it to my wireless router with an Ethernet cable?

Answer. No. The extender is designed to connect wirelessly to the router or access point. Question. What are the user name and default password to log in to the extender?

Answer. If you are online at http://www.mywifiext.net, you can use the following user name and password to log in:

User name. admin Password. password 2. 3. Question. The web browser setup guide keeps asking me for my network security key

(passphrase), and I am sure I have entered the correct passphrase. What can I do?

The extender is probably placed at the borderline of the range covered by the router or access point. For more information, see Place the Extender on page If you are using WEP security, make sure that you are typing the wireless key in the correct field. 10. 4. Question. I am connected to NETGEAR_EXT and launched a browser. Why cant I see the web browser setup genie?

Try these troubleshooting steps:

Make sure that your computer is set up to use DHCP (most are). Make sure that the Client Link LED is green and that you have a valid IP address. Relaunch the web browser and type www.mywifiext.net or www.mywifiext.com in the address field of the web browser. Enter admin for the user name and password for the password. 5. Question. Is seamless roaming supported? During a VoIP call, when I move to a different location the call is dropped. What should I do?

Answer. No, the extender does not support seamless roaming. You might notice performance issues if your network device (laptop, smartphone, or tablet) connects to a different WiFi network. For example, you might connect to the extender WiFi network, begin a call, and then move to the location of your existing network. Your device automatically connects to the network in your current location, which takes a few seconds and might cause your call to be dropped.To prevent this problem, decide which WiFi network you want to use for your VoIP call, and stay within the range of that network. 6. Question. My router security is WEP, and I entered the wrong passphrase or security key on the extender. I cannot access the extender anymore. What can I do?

Answer. The extender cannot detect if the WEP passphrase is correct. If you entered the wrong passphrase, your wireless device cannot get the IP address from the extender. You must reset the extender to the factory settings to get the IP address back. FAQs and Troubleshooting 36 WN3000RPv2 WiFi Range Extender 7. Question. I have enabled a wireless MAC filter (wireless access control or ACL) on my wireless i router. What should I do when installing the extender?

Answer. When the wireless device connects through the extender to your router, the MAC address of the wireless device shown on the router is translated to another MAC address. If your router's MAC filter is enabled, the wireless device connects to the extender but cannot get an IP address from the extender and cannot access the Internet. To allow the wireless device to receive an IP address from the extender and access the Internet, you must provide the translated MAC address to the router. To get the translated MAC address:

1. Disable the MAC filter on your router. 2. Turn on the extender and connect all of your wireless devices to the extender. 3. Make sure that the Link Rate LED remains lit. 4. Log in to the router and check the attached devices on the Attached Devices or similar screen. 5. Add any MAC addresses that begin with 02:0F:B5 to your routers MAC filter table. Cannot Log In to the Extender If you have trouble connecting to the extender, try to locate the source of the problem:

Make sure that you use the correct user name and password to log in:

- User name. admin

- Password. password If your browser displays an error page, make sure that you include http:// when you type http://www.mywifiext.net in the address field of your Internet browser. If you leave it out, you might not be able to connect. If you already set up the extender but can no longer connect to it wirelessly, check if the Link Rate LED is off or red. If you cannot connect to the extender from your computer with WiFi, you can use an Ethernet cable to connect your computer to the Ethernet port on the extender. For more information, see Cable a Computer or Device to the Ethernet Port on page 14. Cannot Join the Extender WiFi Network To join a WiFi network, you must know its network name (also called the SSID) so that you can select it. If the network is secure, you must know the passphrase or key. If the extender does not connect to the network that you select, the following message displays:

Connection was not established to the selected network. If this situation occurs, the cause might be one of the following:

You might have typed the network name, passphrase, or key incorrectly. Use the Setup Wizard to select a WiFi network from the list with detected networks, and retype the FAQs and Troubleshooting 37 WN3000RPv2 WiFi Range Extender passphrase or key. The passphrase or key is case-sensitive. For example, PASSWORD25 is not the same as Password25 or password25. If the extendercannot detect your WiFi network, check to see if your WiFi network is still up. Make sure that the wireless router is turned on. If possible, move the extender closer to the wireless router. If the extender Link Rate LED is red, a poor wireless connection exists between the wireless router and the extender. You can establish the best connection with a clear line of sight between the extender and the wireless router. Make sure that no physical obstacles exist between the extender and the wireless router, and try to move the extender closer to the wireless router. If you use the Setup Wizard, and the extender cannot connect to the wireless router or cannot get an IP address from the wireless router, or the wireless router is not connected to the Internet, the Setup Wizard displays the following message:

You are not able to connect to the Internet. Click Continue to run through setup again to connect to your network. Either run the Setup Wizard again or exit the Setup Wizard and try again later (see and ). FAQs and Troubleshooting 38 A. Supplemental Information This appendix includes the following sections:

Factory Default Settings Technical Specifications A 39 WN3000RPv2 WiFi Range Extender Factory Default Settings The following table includes the factory settings for the extender. You can use the Factory Reset button or the Erase feature to return the extender to these settings.. (See Return the Extender to Its Factory Settings on page 31.) Feature Setup Wizard Wireless communication Setting Enabled Enabled Wireless network names (SSID)s NETGEAR_EXT Security Transmission speed Country/region Operating mode Data rate DHCP Disabled Auto1 Varies by region 802.11n, 802.11g, 802.11b Up to 300 Mbps <<TBD>>

Client enabled 1. Maximum wireless signal rate (IEEE Standard 802.11). Actual throughput will vary. Network conditions and environmental factors, including volume of network traffic, building materials and construction, and network overhead, lower actual data throughput rate. Technical Specifications The following table includes the product specifications. Extender Specifications Network protocol and standards compatibility Data and routing protocols: TCP/IP, DHCP server and client, DNS relay,<<TBD>>

Power consumption Physical specifications Environmental 100-240V ~0.2A, 50-60Hz Dimensions: 67 x 55 x 34 mm Weight: 0.098 kg Operating temperature: 32 to 140F (0 to 40C) Operating humidity: 90% maximum relative humidity, noncondensing Electromagnetic emissions: Meets requirements of FCC Part 15 Class B. Interface Local: 10BASE-T, 100BASE-Tx, RJ-45 802.11n, 802.11g, 802.11b Supplemental Information 40

Notification of Compliance Regulatory Compliance Information This document includes user requirements for operating NETGEAR products in accordance with national laws including usage of radio spectrum and operation of radio devices. Failure of the end-user to comply with the applicable requirements may result in unlawful operation and adverse action against the end-user by the applicable national regulatory authority. The NETGEAR product firmware limits operation to only the channels allowed in a particular region or country. Therefore, all options described in this document may not be available in your version of the product. This document applies to both Class A and Class B devices:

Class A devices are intended to be used in a commercial or industrial environment. They are not intended to be used in a residential home or be available for general public use. Class B devices are intended to be used in a residential setting, and may also be used in commercial and industrial applications. Examples of Class B devices are telephones, personal computers, and residential data gateways. Europe EU Declaration of Conformity This section applies to products bearing the CE or CE! mark:

Products bearing the CE or CE! mark comply with the following EU directives:

EMC Directive 2004/108/EC Low Voltage Directive 2006/95/EC Ecodesign Directive 2009/125/EC RoHS Directive 2011/65/EU If the product has telecommunications functionality, it also complies with the requirement of the following EU directive:

R&TTE Directive 1999/5/EC Compliance with these directives implies conformity to harmonized European standards that are noted in the EU Declaration of Conformity. The EU CE Declaration of Conformity may be found at http://support.netgear.com/app/answers/detail/a_id/11621/. Caution for installing this equipment outdoors: (Valid in all EU member states, EFTA states, and Switzerland.) Be aware that outdoor installations require special attention and will only be handled by trained and qualified installation personnel. No one from the general public is permitted to install NETGEAR wireless products outdoors when external antennas, power and grounding must be installed for use. Particular attention has to be given allowed operational frequencies. Contact NETGEAR for instructions on how to contact an installer for outdoor operations if this product requires the special considerations for outdoor installations. For detailed information concerning installations in France, the user should contact the national spectrum authority in France (http://www.arcep.fr/ ) The following paragraphs apply to WN2500RP:

This device is a 2.4GHz and 5GHz wideband transmission system (transceiver), intended for indoor use only in all EU member states, EFTA states, and Switzerland. In Italy the end-user should apply for a license at the national spectrum authorities in order to obtain authorization to use the device for setting up outdoor radio links and/or for aupplying public access to telecommunications and/or network services. This device may not be used for setting up outdoor radio links in France and in some areas the RF output power may be limited to 10mW EIRP in the frequency range of 2454-2483.5 MHz. For detailed information the end-user should contact the national spectrum authority in France. Warning NETGEAR Class A products that may be utilized in domestic/residential environments may cause radio interference in which case the user may be required to take adequate measures. FCC Requirements for Operation in the United States Information in this section applies to products bearing the FCC mark (or statement):

FCC Information to User This NETGEAR product does not contain any user serviceable components and is to be used with approved antennas only. Any product changes or modifications will invalidate all applicable regulatory certifications and approvals. The following statement applies to these products:

EX6100 EX6200 VEGN2200 WN370 WN2500RP WN3000RPv2 WN3500RP This device and its antenna(s) must not be co-located or operating in conjunction with any other antenna or transmitter except in accordance with FCC multi-transmitter product procedures. FCC Guidelines for Human Exposure This NETGEAR product complies with FCC radiation exposure limits set forth for an uncontrolled environment. The equipment should be installed and operated with minimum distance of 20 cm between the radiator and your body. FCC Declaration of Conformity We, NETGEAR, Inc., 350 East Plumeria Drive, San Jose, CA 95134, declare under our sole responsibility that this product complies with Part 15 Subpart B of FCC CFR47 Rules. Operation is subject to the following two conditions:

The device may not cause harmful interference, and The device must accept any interference received, including interference that may cause undesired operation. FCC Radio Frequency Interference Warnings & Instructions The NETGEAR product has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following methods:

Reorient or relocate the receiving antenna. Connect the equipment into an electrical outlet on a circuit different from that which the radio receiver is Increase the separation between the equipment and the receiver. connected. Consult the dealer or an experienced radio/TV technician for help. FCC RF Radiation Exposure and SAR Statements The information in this section applies to products that transmit data or communicate wirelessly. SAR Statement The information in this section applies to NETGEAR wireless products that are intended to be operated close to human body. NETGEAR products that are intended to be operated close to the human body are tested for body-worn Specific Absorption Rate (SAR) compliance. The SAR limit set by the FCC is 1.6 W/kg. The FCC has established detailed SAR requirements and NETGEAR products meet these requirements. NETGEAR USB products were tested while installed in a host notebook computer. RF Exposure Information NETGEAR products have been evaluated under FCC Bulletin OET 65C (01-01) and found to be compliant to the requirements as set forth in CFR 47 Sections, 2.1093, and 15.247 (b) (4) addressing RF exposure from radio frequency devices. NETGEAR products meet the applicable government requirements for exposure to radio frequency waves. To see the test results reporting the highest SAR level measured for this device, visit http://www.netgear.com/about/regulatory/declarations-conformity/

Radiation exposure: NETGEAR products comply with radiation exposure limits set forth for an uncontrolled environment and meet radio frequency (RF) exposure guidelines for wireless routers. NETGEAR products should be installed and operated keeping the product 20cm or more away from a persons body. For devices that are battery powered and may be operated closer than 20cm to you, refer to the NETGEAR website for exposure levels. FCC Caution Any changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate this equipment. NETGEAR products comply with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) NETGEAR products may not cause harmful interference, and (2) NETGEAR products must accept any interference received, including interference that may cause undesired operation. For products available in the USA market, only channel 1~11 can be operated. Selection of other channels is not possible. The following statement applies to these products:

EX6100 EX6200 VEGN2200 WN370 WN2500RP WN3000RPv2 WN3500RP The device and its antenna(s) must not be co-located or operating in conjunction with any other antenna or transmitter except in accordance with FCC multi-transmitter product procedures. The following statement applies to these products:

EX6100 EX6200 VEGN2200 WN370 WN2500RP The device operates in 5.15~5/25GHz frequency range. It is restricted in indoor environment only. Non-DFS Warning NETGEAR non-DFS products do not support operation in the 5600-5650MHz band. The firmware on the device restricts the operation in this frequency band and does not utilize the channels in this band. NETGEAR non-DFS products will not permit operations on channels 120132 for 11a and 11n/a, which overlap the 56005650MHz band. Country Code Selection Usage (WLAN devices) The country code selection is for non-US model only and is not available to all US model. Per FCC regulation, all WiFi product marketed in US must fixed to US operation channels only. TV Tuner (on Selected Models) The information in this section applies to NETGEAR products incorporating a TV tuner. Note to CATV System Installer: This reminder is provided to call the CATV system installers attention to Section 820-

93 of the National Electrical Code, which provides guidelines for proper grounding and, in particular, specifies that the Coaxial cable shield be connected to the grounding system of the building as close to the point of cable entry as possible. Canadian Department of Communications Radio Interference Regulations The information in this section applies to products bearing the statements:. This digital apparatus does not exceed the Class B limits for radio-noise emissions from digital apparatus as set out in the Radio Interference Regulations of the Canadian Department of Communications. Cet appareil numrique ne dpasse pas les limites de la classe B pour les missions radio bruit des appareils numriques, tel qu'nonc dans le Rglement sur le brouillage radiolectrique du ministre des Communications du Canada. CAN ICES-3 (B)/NMB-3(B) CAN ICES-3 (A)/NMB-3(A) Industry Canada NETGEAR products comply with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) NETGEAR products may not cause harmful interference, and (2) NETGEAR products must accept any interference received, including interference that may cause undesired operation. Ce dispositif est conforme la norme CNR d'Industrie Canada applicable aux appareils radio exempts de licence. Son fonctionnement est sujet aux deux conditions suivantes: (1) le dispositif ne doit pas produire de brouillage prjudiciable, et (2) ce dispositif doit accepter tout brouillage reu, y compris un brouillage susceptible de provoquer un fonctionnement indsirable. IMPORTANT NOTE: Radiation Exposure Statement NETGEAR products comply with IC radiation exposure limits set forth for an uncontrolled environment. NETGEAR products should be installed and operated with minimum distance 20cm between the radiator and your body. For products available in the USA/Canada market, only channel 1~11 can be operated. Selection of other channels is not possible. The following statement applies to these products:

EX6100 EX6200 VEGN2200 WN370 WN2500RP WN3000RPv2 The device and its antenna(s) must not be co-located or operating in conjunction with any other antenna or transmitter except in accordance with IC multi-transmitter product procedures. The following statement applies to these products:

EX6100 EX6200 VEGN2200 WN370 WN2500RP The device for the band 5150-5250 MHz is only for indoor usage to reduce potential for harmful interference to co-

channel mobile satellite systems. NOTE IMPORTANTE: Dclaration d'exposition aux radiations Pour les appareils qui transmettent des donnes sans fil: Cet quipement est conforme aux limites d'exposition aux rayonnements IC tablies pour un environnement non contrl. Cet quipement doit tre install et utilis avec un minimum de 20 cm de distance entre la source de rayonnement et votre corps. Pour les produits disponibles aux tats-Unis / Canada du march, seul le canal 1 11 peuvent tre exploits. Slection d'autres canaux n'est pas possible. La dclaration suivante s'applique ces produits:

EX6100 EX6200 VEGN2200 WN370 WN2500RP WN3000RPv2 Cet appareil et son antenne (s) ne doit pas tre co-localiss ou fonctionnement en association avec une autre antenne ou transmetteur. La dclaration suivante s'applique ces produits:

EX6100 EX6200 VEGN2200 WN370 WN2500RP les dispositifs fonctionnant dans la bande 5150-5250 MHz sont rservs uniquement pour une utilisation lintrieur afin de rduire les risques de brouillage prjudiciable aux systmes de satellites mobiles utilisant les mmes canaux. Interference Reduction Table The table below shows the Recommended Minimum Distance between NETGEAR equipment and household appliances to reduce interference (in feet and meters). Household Appliance Microwave oven Baby monitor analog Baby monitor digital Cordless phone analog Cordless phone digital Bluetooth device ZigBee Recommended Minimum Distance (in feet and meters) 30 feet / 9 meters 20 feet / 6 meters 40 feet / 12 meters 20 feet / 6 meters 30 feet / 9 meters 20 feet / 6 meters 20 feet / 6 meters Japan Notices VCCI This information in this section applies to products bearing the VCCI mark:

Class A ITE A Class B ITE B Japan Wireless Notice South Korea Notices The information in this section applies to products bearing the KCC mark:

:

Class A :

A

( ) Class B :

B

( )

(A)

, .

(B)

, . Taiwan WWAN Wireless Notice The information in this section applies to products bearing the Taiwan National Communications Commission mark:

This telecom equipment has complied with NCC regulations. 5.25-5.35 Thailand Notice The information in this section applies to products approved by the Thailand National Communications Commission:

. China Notices The information in this section applies to products bearing the Chinese Complusory Certification Mark:

This device complies with the requirements in China for Safety and Quality A Australia and New Zealand Notices The information in this section applies to products bearing the Australia C-Tick and A-Tick Compulsory Marks:

This device equipment complies with the Australian and New Zealand regulatory approvals requirements. Warning NETGEAR Class A products that may be utilized in domestic/residential environments may cause radio interference in which case the user may be required to take adequate measures. Powerline Device Safety Information Follow these safety guidelines to ensure your own personal safety and to help protect your system from potential damage:

For national approvals (approval schemes other than CB), relevant national standards for plug, socket-

outlet, and direct plug-in units (for example, US) shall also be consulted while testing and approving such products according to the national standards. Check the electrical current for any device plugged into the filtered AC socket. Do not exceed home and product outlet ratings and electrical requirements. The socket-outlet shall be installed near the equipment and be easily accessible Only power cords and allowed to be inserted into the filtered AC socket; no other equipment with a direct plug-in is allowed. Power cords needs to be a maximum of 1m long and a minimum of 0.75mm of cross-

sectional area. Do not plug devices into the Powerline Pass Thru Adapter filtered AC outlet that exceed the product ratings. The output voltage of the filtered AC outlet is the same as the power outlet that the Powerline Pass Thru Adapter is plugged into. To help avoid damaging your system, be sure that the attached devices are electrically rated to operate with the power available in your location. If the input AC voltage is less than 100 Vac, the device plugged into the filtered AC socket of the Powerline Pass Thru Adapter might not perform as well as expected. DO NOT PLUG MAJOR HOME APPLIANCES into the filtered AC socket or into an attached power strip. The device is not intended to be used with home appliances such as air conditioners, power tools, space heaters, fans hair dryers, ovens, or refrigerators. Actual data throughput will vary. Network conditions and environmental factors, including volume of network traffic, building materials and construction, and network overhead, lower actual data throughput rate. Do not service any product except as explained in your system documentation. Opening or removing covers that are marked with the triangular symbol with a lightning bolt can expose you to electrical shock. Only a trained service technician should service components inside these compartments. Use the product only with approved equipment. Allow the products to cool before removing covers or touching internal components. To help avoid damaging your system, be sure that the voltage selection switch (if provided) on the power supply is set o match the power available at your location:

o o o 110 volts (V), 60 hertz (Hz) in most of North and South America and some Far Eastern countries such as south Korea and Taiwan 100, 50 Hz in eastern Japan and 100, 60Hz in western Japan 230v, 50Hz in most of Europe, the Middle East, and the Far East The peripheral power cables are equipped with three-prong plugs to help ensure proper grounding. Do not use adapter plugs or remove the grounding prong from a cable. Observe extension cable and power strip ratings. Make sure that the total ampere rating of all products plugged into the extension cable or power strip does not exceed 80 percent of the ampere ratings limit for te extension cable or power strip. To help protect your system from sudden, transient increases and decreases in electrical power, use a surge suppressor, line conditioner, or uninterruptible power supply (UPS). Rack Mount Safety Instructions This information applies to the installation of all NETGEAR rack mount products Ambient operating temperature. If the switch is installed in a closed or multiunit rack assembly, the ambient operating temperature of the rack environment might be greater than the ambient temperature of the room. Therefore, consider installing the equipment in an environment compatible with the maximum rated ambient temperature. Reduced airflow. Mount the equipment into a rack so that the amount of airflow required for safe operation is not compromised. Mechanical loading. Mount the equipment into a rack so that a hazardous condition does not arise due to uneven mechanical loading. Circuit overloading. Consider the equipments connection to the power supply circuitry and the effect that any possible overloading of circuits might have on overcurrent protection and power supply wiring. Consider equipment nameplate ratings when addressing this concern. Reliable grounding. This product requires reliable grounding to be maintained at all times. To ensure this, ground the rack itself. Pay particular attention to power supply connections other than the direct connections to the branch circuit (for example, the use of power strips). Clearance. Leave enough clearance in front of the rack (about 25 inches) to enable you to open the front door completely and in the back of the rack (about 30 inches) to allow for sufficient airflow and ease in servicing. NETGEAR, Inc., 350 E. Plumeria Avenue, San Jose, CA 95134 USA December 2013

Project No.: EP391801 Page No. : 3 of 9 Project No.: EP391801 Page No. : 4 of 9 Project No.: EP391801 Page No. : 5 of 9 Project No.: EP391801 Page No. : 6 of 9 Project No.: EP391801 Page No. : 7 of 9 Project No.: EP391801 Page No. : 8 of 9 Project No.: EP391801 Page No. : 9 of 9

Photographs of EUT Project No.: EP391801 Page No. : 1 of 9 Project No.: EP391801 Page No. : 2 of 9

REV DESCRIPTION OF REVISION 01 INITIAL DOCUMENT CREATION ENG APPD DATE M HUMPHREY 07NOV18 7 Pantone Cool Gray 11C NOTE:

1. REFER TO NETGEAR SPEC. DOC-00093 FOR COLOR TOLERANCES. 2. SCALE IS 2:1 3. INK COLOR IS SHOWN TO THE RIGHT. 4. DIE LINES ARE MAGENTA COLOR AND DO NOT PRINT. 5. MAC & SERIAL NUMBERS TO BE PRINTED BY THE ODM. 6. See NTGR DOC-00112 for SN standard. 7. NTGR SN and MAC address barcode to be encoded AIM USS Code39 and include printed characters below barcodes. 8. INSURE COUNTRY OF ORIGIN IS CORRECT. A. IF COUNTRY OF ORIGIN IS PRE-PRINTED, UNHIDE THE APPROPRIATE COUNTRY OF ORIGIN LAYER AND INCLUDE COUNTRY OF ORIGIN ON LABEL. B. IF COUNTRY OF ORIGIN IS POST-PRINTED USING A THERMAL PRINTER (OR EQUIVALENT), OMIT TEXT FROM ARTWORK (USE LAYERS). AUTHOR:

A RAGHUPATHY TITLE:

AW, WN3000RPHv3, PLBL SHEET:

1 of 1 THIS DOCUMENT AND THE DATA DISCLOSED HEREIN OR WHEREWITH IS NOT TO BE REPRODUCED, USED OR DISCLOSED IN WHOLE OR IN PART TO ANYONE WITHOUT THE PERMISSION OF NETGEAR, INC. P/N:

AW-14167-01 REV:

01

REV DESCRIPTION OF REVISION 01 INITIAL DOCUMENT CREATION ENG APPD DATE A RAGHUPATHY 30AUG13 1 0

-

0 9 0 2 1

-

2 7 2 C A M L A I R E S N I P S P W INDOOR USE ONLY, 100-240V 0.1A, 50-60Hz Universal WiFi Range Extender Model: WN3000RPv2 Default Access http://www.mywifiext.net User Name: admin Password: password FCC ID: PY314100251 IC: 4054A-14100251 Router Link Direction Arrows Client Link Power WPS i i n a a n w h a C T n n i i e e d d a a M M 7 NOTE:

1. REFER TO NETGEAR SPEC. DOC-00093 FOR COLOR TOLERANCES. 2. SCALE IS 2:1 3. INK COLOR IS SHOWN TO THE RIGHT. 4. DIE LINES ARE MAGENTA COLOR AND DO NOT PRINT. 5. MAC & SERIAL NUMBERS TO BE PRINTED BY THE ODM. 6. See NTGR DOC-00112 for SN standard. 7. NTGR SN and MAC address barcode to be encoded AIM USS Code39 and include printed characters below barcodes. 8. INSURE COUNTRY OF ORIGIN IS CORRECT. A. IF COUNTRY OF ORIGIN IS PRE-PRINTED, UNHIDE THE APPROPRIATE COUNTRY OF ORIGIN LAYER AND INCLUDE COUNTRY OF ORIGIN ON LABEL. B. IF COUNTRY OF ORIGIN IS POST-PRINTED USING A THERMAL PRINTER (OR EQUIVALENT), OMIT TEXT FROM ARTWORK (USE LAYERS). Pantone Cool Gray 11C AUTHOR:

A RAGHUPATHY TITLE:

AW, WN3000RPv2, V1, PLBL SHEET:

1 of 1 THIS DOCUMENT AND THE DATA DISCLOSED HEREIN OR WHEREWITH IS NOT TO BE REPRODUCED, USED OR DISCLOSED IN WHOLE OR IN PART TO ANYONE WITHOUT THE PERMISSION OF NETGEAR, INC. P/N:

AW-12717-01 REV:

01 Back Label location

Tel: 408-526-1188 Fax: 408-526-1088 Email: TCB@siemic.com 775 Montague Expressway Milpitas, CA 95035 Project and Product Certification Representative Authorization Letter Reason for Amendment (current / obsolete) Initial Release (obsolete) Revised wording (obsolete) Updated company template (obsolete) Updated letter information (obsolete) Added FCC ID field (current) Revision History To 1.0 2.0 3.0 4.0 5.0 From 1.0 1.0 2.0 3.0 4.0 Approved Date Nov-14-2006 Sept25-2007 Jan-31-2012 May-23-2014 Sept 16 2014 SCS-F18: Project and Product Certification Representative Authorization Letter Page 1 of 2 Rev 5.0 NetgearIncorporated Tel:4088903657/Fax:4089078097 350EastPlumeriaDrive,SanJose,CA95134,USA Date: 12/22/2018 To: SIEMIC, INC. 775 Montague Expressway, Milpitas, CA 95035 USA Dear Sir/Madam, Re: Product Certification Representative Authorization Letter We, ____Netgear Incorporated_____hereby authorize SIEMIC, Inc. to act as a Certification Body for certifying for the following project(s):

(Product description: Universal WiFi Range Extender / Model name: WN3000RPHv3) FCC ID: PY314100251 Sincerely, SCS-F18: Project and Product Certification Representative Authorization Letter Page 2 of 2 Rev 5.0

FCC ID: PY314100251 Description of Permissive Change The application is prepared for FCC class II permissive change by adding one model

(WN3000RPHv3). For the device, the Hardware and Software versions are identical. Amanda Wu / Senior Specialist Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch Tel: 886-3-318 3232 ext. 1929 Fax: 886-3-327 0892 Email: amanda.wu@tw.bureauveritas.com

Netgear Incorporated Tel:408-890-3657/Fax:408-907-8097 350 East Plumeria Drive, San Jose, CA 95134, USA Date: 2018-12-21 Federal Communications Commission Innovation, Science and Economic Development Canada 7435 Oakland Mills Road Certification & Engineering Bureau Columbia, MD 21046 3701 Carling Ave., Building 94 Ottawa, Ontario K2H 8S2 SUBJECT: End Product Model Difference Attestation FCC: PY314100251 Models: WN3000RPHv3 We, NETGEAR, hereby declare that our end product, WN3000RPv2, includes WN3000RPHv3 model names as listed above. The above listed models are electrically and mechanically identical. The intention of these models is only for marketing name change purpose. Should you have any question, feel free to contact me directly. Sincerely yours,

------------------- -----------------

-------------------------------------------------------

vid Kay / Reguulal tory David Kay / Regulatory Compliance Director Netgear Incorporated TEL: 4088903657 FAX: 4089078097 E-mail: david.kay@netgear.com

Netgear Incorporated 350 East Plumeria Drive, San Jose, CA 95134, USA Tel:408-890-3657/Fax:408-907-8097 Date: 12/21/2018 FCC ID: PY314100251 AUTHORIZATION LETTER To Whom It May Concern: We, Netgear Incorporated hereby authorizes Amanda Wu / Senior Specialist of Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch (BV CPS Taoyuan), to act on its behalf in all matters relating to the Federal Communication Commission (FCC) application for equipment authorization in connection with the FCC ID listed above, including signing of all documents relating to these matters. Any and all acts carried out by Amanda Wu / Senior Specialist of BV CPS Taoyuan on Netgear Incorporateds behalf, within the scope of the powers granted herein, shall have the same effect as acts of its own. If you have any questions regarding the authorization, please dont hesitate to contact us. Thank you! Sincerely yours, ------------------------------------------------------ David Kay / Regulatory Compliance Director Netgear Incorporated TEL: 4088903657 FAX: 4089078097 E-mail: david.kay@netgear.com

Netgear Inc. 350 East Plumeria Drive San Jose, CA 95134 U.S.A. Date: January 23, 2014 Subject: Ad Hoc Mode Function Declaration To whom it may concern, We, NETGEAR, Inc. declare that the WN3000RPv2 does not support any non-US channels and country code selection in all the operational modes. Reference FCC ID: PY314100251 Regards, Applicants company name

: NETGEAR,Inc. Applicants company address Signature

: 350 East Plumeria Drive, San Jose, California 95134, USA

:

Name and Job Title

: David Kay / Regulatory Compliance Manager E-Mail Tel.

: David.Kay@Netgear.com

: 408-890-3657

Netgear Inc. 350 East Plumeria Drive San Jose, CA 95134 U.S.A. Date: January 23, 2014 Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Rd Columbia MD 21046-1609 Subject: Request for confidentiality FCC ID: PY314100251 To whom it may concern:

Short-term confidentiality Pursuant to DA 04-1705 of the Commissions public notice, in order to comply with the marketing regulations in 47CFR 2.803 and the importation rules in 47 CFR 2.1204, while ensuring that business sensitive information remains confidential until the actual marketing of newly authorized devices. We are requesting the commission to grant short-term confidentiality request on the following attachments for 180 days. Internal Photographs External Photographs User's manual Test Set up photo Permanent confidentiality Pursuant to Sections 0.457 and 0.459 of the Commissions Rules, the Applicant Hereby requests confidential treatment of information accompanying this Application As outlined below:

Block Diagram Schematics Operation description The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these materials may be harmful to the applicant and provide unjustified benefits to its competitors. The applicant understands that pursuant to Section 0.457 of the Rules, disclosure of this application and all accompanying documentation will not be made before the date of the Grant for this application. Should you require any further information, please contact the undersigned. Thank you for your consideration in this matter.

: NETGEAR, Inc.

: 350 East Plumeria Drive, San Jose, California 95134, USA Applicant Address Signature

:

_________________________________ Name and Job Title. E-mail Tel.

: David Kay / Regulatory Compliance Manager

: David.Kay@Netgear.com

: 408-890-3657

Netgear Inc. 350 East Plumeria Drive San Jose, CA 95134 U.S.A. Date: 2014/1/23 Federal Communications Commission 7435 Oakland Mills Rd Columbia MD 21046-1609 Subject: Product Certification Representative Authorization Letter FCC ID: PY314100251 To whom it may concern:

We the undersigned, hereby authorize following person to act as our agent in the preparation of this application for equipment authorization of the FCC Rules and Regulations. International Certification Corp. Address

:

No.3-1, Lane 6, Wen San 3rd St. Kwei Shan Hsiang, Tao Yuan Hsein 333, Taiwan

(R.O.C.)

: Gary Chang

: Manager

: garychang@icertifi.com.tw Webs Name Job Title e-mail We further certify that neither the applicant nor any party to this application, as defined in 47 CFR Ch. 1.2002(b), is subject to a denial to Federal benefits, that include FCC benefits, pursuant to section 5301 of the Anti-Drug Abuse Act of 1998, 21 U.S.C. 835(a). This appointment also includes the authority to complete FCC Form 731 on our behalf and sign the application as an authorized agent. Applicant Address Signature Name and Job Title. E-mail Tel.

: NETGEAR, Inc.

: 350 East Plumeria Drive, San Jose, California 95134, USA

:

_________________________________

: David Kay / Regulatory Compliance Manager

: David.Kay@Netgear.com

: 408-890-3657

FCC RF Exposure Report FCC ID Equipment Model No. Brand Name Applicant Address

: PY314100251

: Universal WiFi Range Extender

: WN3000RPv2

: NETGEAR

: NETGEAR, Inc.

: 350 East Plumeria Drive, San Jose, California 95134, USA Standard Received Date Tested Date

: 47 CFR FCC Part 2.1091

: Nov. 25, 2013

: Nov. 25 ~ Dec. 08, 2013 We, International Certification Corp., would like to declare that the tested sample has been evaluated and in compliance with the requirement of the above standards. The test results contained in this report refer exclusively to the product. It may be duplicated completely for legal use with the approval of the applicant. It shall not be reproduced except in full without the written approval of our laboratory. Approved & Reviewed by:

Gary Chang / Manager Ty: XXX Report No.: FA391801 Report Version: Rev. 02 Page : 1 of 5 Table of Contents MPE EVALUATION OF MOBILE DEVICES ......................................................................................... 4 LIMITS FOR GENERAL POPULATION/UNCONTROLLED EXPOSURE............................................. 4 MPE EVALUATION FORMULA ............................................................................................................. 4 MPE EVALUATION RESULTS .............................................................................................................. 4 TEST LABORATORY INFORMATION ................................................................................................. 5 1 1.1 1.2 1.3 2 Report No.: FA391801 Report Version: Rev. 02 Page : 2 of 5 Release Record Report No. FA391801 FA391801 Version Rev. 01 Rev. 02 Description Initial issue Modified FCC ID (page 1) Issued Date Jan. 09, 2014 Jan. 23, 2014 Report No.: FA391801 Report Version: Rev. 02 Page : 3 of 5 1 MPE EVALUATION OF MOBILE DEVICES Human exposure to RF emissions from mobile devices (47 CFR 2.1091) may be evaluated based on the MPE limits adopted by the FCC for electric and magnetic field strength and/or power density, as appropriate, since exposures are assumed to occur at distances of 20 cm or more from persons. 1.1 LIMITS FOR GENERAL POPULATION/UNCONTROLLED EXPOSURE Frequency Range (MHz) Power Density (mW /cm2) Averaging Time (minutes) 300~1500 1500~100000 F/1500 1.0 1.2 MPE EVALUATION FORMULA 30 30 Pd =

Pt 2*

RPi

*4 Where Pd= Power density in mW/cm2 Pt= EIRP in Mw Pi= 3.1416 R= Measurement distance 1.3 MPE EVALUATION RESULTS Frequency Range (MHz) Maximum Conducted Power (dBm) Antenna Gain

(dBi) Distance

(cm) Power Density

(mW/cm2) Limit (mW/cm2) 2412~2462 23.93 2.38 20 0.085 1 Report No.: FA391801 Report Version: Rev. 02 Page : 4 of 5 Test laboratory information 2 Established in 2012, ICC provides foremost EMC & RF Testing and advisory consultation services by our skilled engineers and technicians. Our services employ a wide variety of advanced edge test equipment and one of the widest certification extents in the business. International Certification Corp, it is our definitive objective is to institute long term, trust-based associations with our clients. The expectation we set up with our clients is based on outstanding service, practical expertise and devotion to a certified value structure. Our passion is to grant our clients with best EMC / RF services by oriented knowledgeable and accommodating staff. Our Test sites are located at Linkou District and Kwei Shan Hsiang. Location map can be found on our website http://www.icertifi.com.tw. Linkou Tel: 886-3-271-8666 No. 30-2, Ding Fwu Tsuen, Lin Kou District, New Taipei City, Taiwan, R.O.C. If you have any suggestion, please feel free to contact us as below information Tel: 886-3-271-8666 Fax: 886-3-318-0155 Email: ICC_Service@icertifi.com.tw END Kwei Shan Tel: 886-3-271-8666 No. 3-1, Lane 6, Wen San 3rd St., Kwei Shan Hsiang, Tao Yuan Hsien 333, Taiwan, R.O.C. Report No.: FA391801 Report Version: Rev. 02 Page : 5 of 5

Photographs of the Test Configuration Conducted Emission Test Report No.: FR391801 Report Version: Rev. 01 Page: : 1 of 2 Radiated Emission Test Report No.: FR391801 Report Version: Rev. 01 Page: : 2 of 2

FCC Test Report FCC ID Equipment Model No. Brand Name Applicant Address

: PY314100251

: Universal WiFi Range Extender

: WN3000RPv2

: NETGEAR

: NETGEAR, Inc.

: 350 East Plumeria Drive, San Jose, California 95134, USA Standard Received Date Tested Date

: 47 CFR FCC Part 15.247

: Nov. 25, 2013

: Nov. 25 ~ Dec. 08, 2013 We, International Certification Corp., would like to declare that the tested sample has been evaluated and in compliance with the requirement of the above standards. The test results contained in this report refer exclusively to the product. It may be duplicated completely for legal use with the approval of the applicant. It shall not be reproduced except in full without the written approval of our laboratory. Approved & Reviewed by:

Gary Chang / Manager Ty: XXX Report No.: FR391801 Report Version: Rev. 02 Page : 1 of 60 Table of Contents GENERAL DESCRIPTION .................................................................................................................... 5 Information .............................................................................................................................................. 5 Local Support Equipment List ................................................................................................................ 8 Test Setup Chart .................................................................................................................................... 8 The Equipment List ................................................................................................................................ 9 Test Standards ..................................................................................................................................... 11 Measurement Uncertainty .................................................................................................................... 11 TEST CONFIGURATION ..................................................................................................................... 12 Testing Condition ................................................................................................................................. 12 The Worst Test Modes and Channel Details ....................................................................................... 12 TRANSMITTER TEST RESULTS ........................................................................................................ 13 Conducted Emissions ........................................................................................................................... 13 6dB and Occupied Bandwidth .............................................................................................................. 16 RF Output Power .................................................................................................................................. 19 Power Spectral Density ........................................................................................................................ 21 Unwanted Emissions into Restricted Frequency Bands ...................................................................... 23 Emissions in non-restricted frequency bands ...................................................................................... 51 TEST LABORATORY INFORMATION ............................................................................................... 60 1 1.1 1.2 1.3 1.4 1.5 1.6 2 2.1 2.2 3 3.1 3.2 3.3 3.4 3.5 3.6 4 Report No.: FR391801 Report Version: Rev. 02 Page : 2 of 60 Release Record Report No. FR391801 FR391801 Version Rev. 01 Rev. 02 Description Initial issue Modified FCC ID (page 1) Issued Date Jan. 09, 2014 Jan. 23, 2014 Report No.: FR391801 Report Version: Rev. 02 Page : 3 of 60 Summary of Test Results FCC Rules Test Items Measured 15.207 Conducted Emissions 15.247(d) 15.209 Radiated Emissions 15.247(b)(3) Fundamental Emission Output Power 15.247(a)(2) 15.247(e) 15.203 6dB Bandwidth Power Spectral Density Antenna Requirement

[dBuV]: 0.197 MHz 57.56 (Margin -6.2dB) QP

[dBuV/m at 3m]: 2483.50 MHz 53.90 (Margin -0.1 dB) - AV Power [dBm]:

11b: 23.93 11g: 23.70 HT20: 23.66 HT40: 18.58 Meet the requirement of limit Meet the requirement of limit Meet the requirement of limit Result Pass Pass Pass Pass Pass Pass Report No.: FR391801 Report Version: Rev. 02 Page : 4 of 60 General Description Information 1 1.1 1.1.1 Specification of the Equipment under Test (EUT) Frequency Range (MHz) 2400-2483.5 2400-2483.5 2400-2483.5 2400-2483.5 IEEE Std. 802.11 b g n (HT20) n (HT40) Ch. Freq. (MHz) RF General Information Channel Number 1-11 [11]

1-11 [11]

1-11 [11]

3-9 [7]

2412-2462 2412-2462 2412-2462 2422-2452 Transmit Chains (NTX) Data Rate /

MCS 2 2 2 2 1-11 Mbps 6-54 Mbps MCS 0-15 MCS 0-15 Note 1: RF output power specifies that Maximum Conducted (Average) Output Power. Note 2: 802.11b uses a combination of DSSS-DBPSK, DQPSK, CCK modulation. Note 3: 802.11g/n uses a combination of OFDM-BPSK, QPSK, 16QAM, 64QAM modulation. 1.1.2 Antenna Details Model 401-10096-01 401-10095-01 Type Dipole Dipole Gain (dBi) Connector Remark 2.13 2.38 U.FL U.FL

---

---

1.1.3 EUT Operational Condition Power Supply Type I/P: 100-240 Vac, 50-60Hz , 0.3A, Report No.: FR391801 Report Version: Rev. 02 Page : 5 of 60 1.1.4 Accessories N/A 1.1.5 Channel List Frequency band (MHz) 802.11 b / g / n HT20 2400~2483.5 802.11n HT40 Channel Frequency(MHz) Channel Frequency(MHz) 1 2 3 4 5 6 7 8 9 10 11 2412 2417 2422 2427 2432 2437 2442 2447 2452 2457 2462 3 4 5 6 7 8 9

---

---

---

---

2422 2427 2432 2437 2442 2447 2452

---

---

---

---

1.1.6 Test Tool and Duty Cycle Test tool Duty Cycle Of Test Signal (%) Duty Factor MT7620 QA, Ver 1.0.6.0 100.00% - IEEE 802.11b 99.01% - IEEE 802.11g 98.95% - IEEE 802.11n (HT20) 98.31% - IEEE 802.11n (HT40) 0.00 - IEEE 802.11b 0.04 - IEEE 802.11g 0.05- IEEE 802.11n (HT20) 0.07 - IEEE 802.11n (HT40) Report No.: FR391801 Report Version: Rev. 02 Page : 6 of 60 1.1.7 Power Setting Modulation Mode 11b 11b 11b 11g 11g 11g HT20 HT20 HT20 HT40 HT40 HT40 Test Frequency (MHz) Power Set 2412 2437 2462 2412 2437 2462 2412 2437 2462 2422 2437 2452 1A/1A 1F/1F 1D/1D 08/08 23/23 07/08 06/06 23/23 06/06 04/04 0A/0A 03/03 Report No.: FR391801 Report Version: Rev. 02 Page : 7 of 60 1.2 Local Support Equipment List Support Equipment List No. Equipment Brand 1 Notebook DELL Model E6430 S/N

---

FCC ID DoC Signal cable / Length (m) RJ45, 10m non-shielded w/o core. 1.3 Test Setup Chart Test Setup Diagram Report No.: FR391801 Report Version: Rev. 02 Page : 8 of 60 1.4 The Equipment List Test Item Test Site Conducted Emission Conduction room 1 / (CO01-WS) Instrument EMC Receiver Manufacturer R&S Model No. ESCS 30 Serial No. 100169 Calibration Date Calibration Until Oct. 15, 2013 Oct. 14, 2014 LISN ISN ISN ISN 50 ohm terminal 50 ohm terminal 50 ohm terminal 50 ohm terminal

(Support Unit) SCHWARZBECK MESS-ELEKTRONIK Schwarzbeck 8127 8127-667 Nov. 23, 2013 Nov. 22, 2014 TESEQ TESEQ TESEQ NA NA NA NA ISN T800 ISN T200A ISN ST08 50 50 50 50 34406 30494 22589 01 02 03 04 Apr. 08, 2013 Apr. 09, 2013 Jan. 24, 2013 Apr. 22, 2013 Apr. 22, 2013 Apr. 22, 2013 Apr. 07, 2014 Apr. 08, 2014 Jan. 23, 2014 Apr. 21, 2014 Apr. 21, 2014 Apr. 21, 2014 Apr. 22, 2013 Apr. 21, 2014 Note: Calibration Interval of instruments listed above is one year. Test Item Test Site Instrument RF Conducted

(TH01-WS) Manufacturer Spectrum Analyzer Power Meter Power Sensor Signal Generator R&S Anritsu Anritsu R&S Model No. FSV 40 ML2495A MA2411B SMB100A Serial No. 101063 1241002 1027366 175727 Calibration Date Calibration Until Feb. 18, 2013 Oct. 24, 2013 Oct. 24, 2013 Jan. 14, 2013 Feb. 17, 2014 Oct. 23, 2014 Oct. 23, 2014 Jan. 13, 2014 Note: Calibration Interval of instruments listed above is one year. Report No.: FR391801 Report Version: Rev. 02 Page : 9 of 60 Test Item Test Site Radiated Emission 966 chamber 2 / (03CH02-WS) Instrument Manufacturer Model No. Serial No. Calibration Date Calibration Until 3m semi-anechoic chamber Spectrum Analyzer Receiver CHAMPRO R&S R&S SAC-03 FSV40 ESR3 03CH02-WS Jan. 02, 2013 Jan. 01, 2014 101499 101657 Jan. 28, 2013 Jan. 30,2013 Jan. 11, 2013 Jan. 27, 2014 Jan. 29, 2014 Jan. 10, 2014 ScHwarzbeck VULB9168 VULB9168-524 Bilog Antenna Horn Antenna Horn Antenna 1G-18G BBHA 9120D BBHA 9120 D 1095 Jan. 29, 2013 SCHWARZBECK Jan. 28,2014 SCHWARZBECK BBHA 9170 BBHA 9170517 Jan. 14, 2013 Jan. 13, 2014 Burgeon Agilent 18G-40G Amplifier Amplifier RF Cable RF Cable RF Cable HUBER+SUHNER HUBER+SUHNER HUBER+SUHNER MY39501309 MY16140/4 MY16018/4 MY16015/4 BPA-530 83017A 100218 Dec. 14, 2012 Dec. 18, 2012 Dec. 25, 2012 Dec. 25, 2012 Dec. 25, 2012 Dec. 25, 2012 Dec. 25, 2012 Dec. 13, 2013 Dec. 17, 2013 Dec. 24, 2013 Dec. 24, 2013 Dec. 24, 2013 Dec. 24, 2013 Dec. 24, 2013 SUCOFLEX104 SUCOFLEX104 SUCOFLEX104 CFD400NL-LW CFD400NL-LW RF Cable-R03m RF Cable-R10m Woken Woken CFD400NL-003 CFD400NL-004 control EM Electronics EM1000 060608 N/A N/A Note: Calibration Interval of instruments listed above is one year. Radiated Emission 966 chamber 2 / (03CH02-WS) Test Item Test Site Instrument Loop Antenna Amplifier AMF-6F-260400 Note: Calibration Interval of instruments listed above is two year. Manufacturer R&S MITEQ Model No. HFH2-Z2 Serial No. 100330 9121372 Calibration Date Calibration Until Nov. 15, 2012 Apr. 19, 2013 Nov. 14, 2014 Apr. 18, 2015 Report No.: FR391801 Report Version: Rev. 02 Page : 10 of 60 1.5 Test Standards According to the specification of EUT, the EUT must comply with following standards and KDB documents. 47 CFR FCC Part 15.247 ANSI C63.10-2009 FCC KDB 558074 D01 DTS Meas Guidance v03r01 FCC KDB 662911 D01 Multiple Transmitter Output v02r01 Note: The EUT has been tested and complied with FCC part 15B requirement. FCC Part 15B test results are issued to another report. 1.6 Measurement Uncertainty ISO/IEC 17025 requires that an estimate of the measurement uncertainties associated with the emissions test results be included in the report. The measurement uncertainties given below are based on a 95% confidence level (based on a coverage factor (k=2) Measurement Uncertainty Parameters Bandwidth Conducted power Frequency error Temperature Conducted emission AC conducted emission Radiated emission Uncertainty 35.286 Hz 0.536 dB 35.286 Hz 0.3 oC 2.946 dB 2.43 dB 2.49 dB Report No.: FR391801 Report Version: Rev. 02 Page : 11 of 60 Test Configuration 2 2.1 Testing Condition Test Item AC Conduction Radiated Emissions RF Conducted FCC site registration No.: 657002 IC site registration No.: 10807A-2 Test Site CO01-WS 03CH02-WS TH01-WS Ambient Condition 18C / 45%

23C / 66%

25C / 60%

Tested By Skys Huang Aska Huang Felix Sung 2.2 The Worst Test Modes and Channel Details Data rate

(Mbps) / MCS Test Configuration Test item Conducted Emissions Radiated Emissions < 1GHz Radiated Emissions > 1GHz Fundamental Emission Output Power 6dB bandwidth Modulation Mode 11b 11b 11b 11g HT20 HT40 Test Frequency

(MHz) 2437 2437 2412 / 2437 / 2462 2412 / 2437 / 2462 2412 / 2437 / 2462 2422 / 2437 / 2452 11b 11g HT20 HT40 2412 / 2437 / 2462 2412 / 2437 / 2462 2412 / 2437 / 2462 2422 / 2437 / 2452 6 Mbps 6 Mbps 1 Mbps 6 Mbps MCS 0 MCS 0 1 Mbps 6 Mbps MCS 0 MCS 0

---

---

---

---

Power spectral density NOTE:

1. The EUT was pretested with 3 orientations placed on the table for the radiated emission measurement X, Y, and Z-plane. The Y-plane results were found as the worst case and were shown in this report. Report No.: FR391801 Report Version: Rev. 02 Page : 12 of 60 Transmitter Test Results 3 3.1 Conducted Emissions 3.1.1 Limit of Conducted Emissions Conducted Emissions Limit Frequency Emission (MHz) 0.15-0.5 Quasi-Peak 66 - 56 *

56 60 Note 1: * Decreases with the logarithm of the frequency. 0.5-5 5-30 Average 56 - 46 *

46 50 3.1.2 Test Procedures 1. The device is placed on a test table, raised 80 cm above the reference ground plane. The vertical conducting plane is located 40 cm to the rear of the device. The device is connected to line impedance stabilization network (LISN) and other accessories are connected to other LISN. Measured levels of AC power line conducted emission are across the 50 LISN port. AC conducted emission measurements is made over frequency range from 150 kHz to 30 MHz. This measurement was performed with AC 120V / 60Hz. 2. 3. 4. 3.1.3 Test Setup Report No.: FR391801 Report Version: Rev. 02 Page : 13 of 60 3.1.4 Test Result of Conducted Emissions Power Phase Test Mode Line 1 Test Freq. (MHz) 2437 Note 1: Level (dBuV) = Read Level (dBuV) + LISN Factor (dB) + Cable Loss (dB). 2: Over Limit (dBuV) = Limit Line (dBuV) Level (dBuV). Report No.: FR391801 Report Version: Rev. 02 Page : 14 of 60 Power Phase Test Mode Neutral 1 Test Freq. (MHz) 2437 Note 1: Level (dBuV) = Read Level (dBuV) + LISN Factor (dB) + Cable Loss (dB). 2: Over Limit (dBuV) = Level (dBuV) - Limit Line (dBuV). Report No.: FR391801 Report Version: Rev. 02 Page : 15 of 60 3.2 3.2.1 Limit of 6dB Bandwidth The minimum 6dB bandwidth shall be at least 500 kHz. 6dB and Occupied Bandwidth 3.2.2 Test Procedures 1. 2. 3. 4. Set resolution bandwidth (RBW) = 100 kHz, Video bandwidth = 300 kHz. Detector = Peak, Trace mode = max hold. Sweep = auto couple, Allow the trace to stabilize. Measure the maximum width of the emission that is constrained by the frequencies associated with the two outermost amplitude points (upper and lower) that are attenuated by 6dB relative to the maximum level measured in the fundamental emission. 3.2.3 Test Setup Report No.: FR391801 Report Version: Rev. 02 Page : 16 of 60 3.2.4 Test Result of 6dB and Occupied Bandwidth Modulation Mode NTX Freq. (MHz) 11b 11b 11b 11g 11g 11g HT20 HT20 HT20 HT40 HT40 HT40 2 2 2 2 2 2 2 2 2 2 2 2 2412 2437 2462 2412 2437 2462 2412 2437 2462 2422 2437 2452 Chain 0 10.09 10.09 10.09 16.35 16.35 16.35 17.33 17.28 17.04 36.06 36.06 36.29 6dB Bandwidth (MHz) Chain 1 Chain 2 10.09 10.09 10.09 16.35 16.35 16.35 17.16 17.10 17.10 36.06 35.83 36.06

---

---

---

---

---

---

---

---

---

---

---

---

Worst Plots Report No.: FR391801 Report Version: Rev. 02 Limit (kHz) Chain 3

---

---

---

---

---

---

---

---

---

---

---

---

500 500 500 500 500 500 500 500 500 500 500 500 Page : 17 of 60 99% Occupied Bandwidth (MHz) Modulation Mode NTX Freq.

(MHz) 11b 11b 11b 11g 11g 11g HT20 HT20 HT20 HT40 HT40 HT40 2 2 2 2 2 2 2 2 2 2 2 2 2412 2437 2462 2412 2437 2462 2412 2437 2462 2422 2437 2452 Chain 0 12.50 12.97 12.62 17.08 25.30 17.08 17.83 25.93 17.83 36.82 37.05 36.93 Chain 1 12.56 13.02 12.62 17.08 25.01 17.02 17.77 26.74 17.77 36.82 37.05 36.82 Worst Plots Chain 2 Chain 3

---

---

---

---

---

---

---

---

---

---

---

---

---

---

---

---

---

---

---

---

---

---

---

---

Report No.: FR391801 Report Version: Rev. 02 Page : 18 of 60 3.3 RF Output Power 3.3.1 Limit of RF Output Power Conducted power shall not exceed 1Watt. Antenna gain <= 6dBi, no any corresponding reduction is in output power limit. Antenna gain > 6dBi Non Fixed, point to point operations. The conducted output power from the intentional radiator shall be reduced by the amount in dB that the directional gain of the antenna exceeds 6 dB Fixed, point to point operations Systems operating in the 24002483.5 MHz band that are used exclusively for fixed, point-to-point Operations, maximum peak output power of the intentional radiator is reduced by 1 dB for every 3 dB that the directional gain of the antenna exceeds 6 dBi. Systems operating in the 57255850 MHz band that are used exclusively for fixed, point-to-point operations ,no any corresponding reduction is in transmitter peak output power 3.3.2 Test Procedures Maximum Peak Conducted Output Power Spectrum analyzer 1. 2. 3. Set RBW = 1MHz, VBW = 3MHz, Detector = Peak. Sweep time = auto, Trace mode = max hold, Allow trace to fully stabilize. Use the spectrum analyzer channel power measurement function with the band limits set equal to the DTS bandwidth edges. Power meter 1. A broadband Peak RF power meter is used for output power measurement. The video bandwidth of power meter is greater than DTS bandwidth of EUT. If duty cycle of test signal is not 100 %, trigger and gating function of power meter will be enabled to capture transmission burst for measuring output power. Maximum Conducted Output Power Spectrum analyzer 1. 2. 3. 4. Set RBW = 1MHz, VBW = 3MHz, Detector = RMS. Set the sweep time to: 10 x (number of measurement points in sweep) x (maximum data rate per stream). Perform the measurement over a single sweep. Use the spectrum analyzers band power measurement function with band limits set equal to the EBW(26dBc) band edges. Power meter 1. A broadband Average RF power meter is used for output power measurement. The video bandwidth of power meter is greater than DTS bandwidth of EUT. If duty cycle of test signal is not 100 %, trigger and gating function of power meter will be enabled to capture transmission burst for measuring output power. Report No.: FR391801 Report Version: Rev. 02 Page : 19 of 60 3.3.3 Test Setup 3.3.4 Test Result of Maximum Output Power Modulation Mode NTX Freq.

(MHz) 11b 11b 11b 11g 11g 11g HT20 HT20 HT20 HT40 HT40 HT40 2 2 2 2 2 2 2 2 2 2 2 2 2412 2437 2462 2412 2437 2462 2412 2437 2462 2422 2437 2452 Conducted (average) output power

(dBm) Chain 0 Chain 1 Chain 2 Chain 3 19.75 20.83 19.94 15.76 20.70 14.50 14.72 20.64 14.12 12.95 15.58 12.69 19.63 21.01 19.87 15.51 20.67 14.69 14.62 20.65 14.03 13.04 15.55 12.52

---

---

---

---

---

---

---

---

---

---

---

---

---

---

---

---

---

---

---

---

---

---

---

---

Total Total Power Power

(mW)

(dBm) 186.239 22.70 247.243 23.93 195.679 22.92 73.234 18.65 234.171 23.70 57.628 17.61 58.622 17.68 232.023 23.66 51.116 17.09 39.861 16.01 72.033 18.58 36.443 15.62 Limit

(dBm) 30 30 30 30 30 30 30 30 30 30 30 30 Report No.: FR391801 Report Version: Rev. 02 Page : 20 of 60 3.4 Power Spectral Density 3.4.1 Limit of Power Spectral Density Power spectral density shall not be greater than 8 dBm in any 3 kHz band. 3.4.2 Test Procedures Maximum peak conducted output power was used to demonstrate compliance to the fundamental output power limit. 1. 2. 3. 4. Set the RBW = 30kHz, VBW = 100kHz. Detector = Peak, Sweep time = auto couple. Trace mode = max hold, allow trace to fully stabilize. Use the peak marker function to determine the maximum amplitude level. Maximum (average) conducted output power was used to demonstrate compliance to the fundamental output power limit. 1. 2. 3. 4. Set the RBW = 30kHz, VBW = 100 kHz. Detector = RMS, Sweep time = auto couple. Employ trace average mode over a minimum of 100 traces. Use the peak marker function to determine the maximum amplitude level. 3.4.3 Test Setup Report No.: FR391801 Report Version: Rev. 02 Page : 21 of 60 3.4.4 Test Result of Power Spectral Density Modulation Mode NTX Freq.

(MHz) Total Power Spectral Density

(dBm/30kHz) Limit (dBm/3kHz) 11b 11b 11b 11g 11g 11g HT20 HT20 HT20 HT40 HT40 HT40 2 2 2 2 2 2 2 2 2 2 2 2 2412 2437 2462 2412 2437 2462 2412 2437 2462 2422 2437 2452

-0.83 0.69

-0.50

-6.01

-1.22

-6.87

-7.40

-1.54

-7.56

-12.09

-8.97

-11.34 Note: Test result is bin-by-bin summing measured value of each TX port. Worst Plots 8 8 8 8 8 8 8 8 8 8 8 8 Report No.: FR391801 Report Version: Rev. 02 Page : 22 of 60 3.5 Unwanted Emissions into Restricted Frequency Bands 3.5.1 Limit of Unwanted Emissions into Restricted Frequency Bands Frequency Range (MHz) Field Strength (uV/m) Field Strength (dBuV/m) Measure Distance (m) Restricted Band Emissions Limit 0.009~0.490 0.490~1.705 1.705~30.0 30~88 88~216 216~960 Above 960 2400/F(kHz) 24000/F(kHz) 48.5 - 13.8 33.8 - 23 30 100 150 200 500 29 40 43.5 46 54 300 30 30 3 3 3 3 Note 1:

Qusai-Peak value is measured for frequency below 1GHz except for 990 kHz, 110490 kHz frequency band. Peak and average value are measured for frequency above 1GHz. The limit on average radio frequency emission is as above table. The limit on peak radio frequency emissions is 20 dB above the maximum permitted average emission limit Note 2:

Measurements may be performed at a distance other than what is specified provided. When performing measurements at a distance other than that specified, the results shall be extrapolated to the specified distance using an extrapolation factor as below, Frequency at or above 30 MHz: 20 dB/decade Frequency below 30 MHz: 40 dB/decade. 3.5.2 Test Procedures 1. Measurement is made at a semi-anechoic chamber that incorporates a turntable allowing a EUT rotation of 360. A continuously-rotating, remotely-controlled turntable is installed at the test site to support the EUT and facilitate determination of the direction of maximum radiation for each EUT emission frequency. The EUT is placed at a height of 0.8 m test table above the ground plane. Measurement is made with the antenna positioned in both the horizontal and vertical planes of polarization. The measurement antenna is varied in height (1m ~ 4m) above the reference ground plane to obtain the maximum signal strength. Distance between EUT and antenna is 3 m. This investigation is performed with the EUT rotated 360, the antenna height scanned between 1 m and 4 m, and the antenna rotated to repeat the measurements for both the horizontal and vertical antenna polarizations. 2. 3. Note:

1. 2. 3. 120kHz measurement bandwidth of test receiver and Quasi-peak detector is for radiated emission below 1GHz. RBW=1MHz, VBW=3MHz and Peak detector is for peak measured value of radiated emission above 1GHz. RBW=1MHz, VBW=1/T and Peak detector is for average measured value of radiated emission above 1GHz. Report No.: FR391801 Report Version: Rev. 02 Page : 23 of 60 3.5.3 Test Setup Radiated Emissions below 1 GHz Radiated Emissions above 1 GHz Report No.: FR391801 Report Version: Rev. 02 Page : 24 of 60 3.5.4 Transmitter Radiated Unwanted Emissions (Below 1GHz) Modulation Polarization 11b Horizontal Test Freq. (MHz) 2437 Note 1: Emission Level (dBuV/m) = SA Reading (dBuV/m) + Factor* (dB)

*Factor includes antenna factor , cable loss and amplifier gain Note 2: Margin (dB) = Emission level (dBuV/m) Limit (dBuV/m). Note 3: All amplitude of spurious emissions below 30MHz that are attenuated by more than 20 dB below the permissible value has no need to be reported. Report No.: FR391801 Report Version: Rev. 02 Page : 25 of 60 Modulation Polarization 11b Vertical Test Freq. (MHz) 2437 Note 1: Emission Level (dBuV/m) = SA Reading (dBuV/m) + Factor* (dB)

*Factor includes antenna factor , cable loss and amplifier gain Note 2: Margin (dB) = Emission level (dBuV/m) Limit (dBuV/m). Note 3: All amplitude of spurious emissions below 30MHz that are attenuated by more than 20 dB below the permissible value has no need to be reported. Report No.: FR391801 Report Version: Rev. 02 Page : 26 of 60 3.5.5 Transmitter Radiated Unwanted Emissions (Above 1GHz) for 11b Modulation Polarization 11b Horizontal Test Freq. (MHz) 2412 Note 1: Emission Level (dBuV/m) = SA Reading (dBuV/m) + Factor* (dB)

*Factor includes antenna factor , cable loss and amplifier gain Note 2: Margin (dB) = Emission level (dBuV/m) Limit (dBuV/m). Report No.: FR391801 Report Version: Rev. 02 Page : 27 of 60 Modulation Polarization 11b Vertical Test Freq. (MHz) 2412 Note 1: Emission Level (dBuV/m) = SA Reading (dBuV/m) + Factor* (dB)

*Factor includes antenna factor , cable loss and amplifier gain Note 2: Margin (dB) = Emission level (dBuV/m) Limit (dBuV/m). Report No.: FR391801 Report Version: Rev. 02 Page : 28 of 60 Modulation Polarization 11b Horizontal Test Freq. (MHz) 2437 Note 1: Emission Level (dBuV/m) = SA Reading (dBuV/m) + Factor* (dB)

*Factor includes antenna factor , cable loss and amplifier gain Note 2: Margin (dB) = Emission level (dBuV/m) Limit (dBuV/m). Report No.: FR391801 Report Version: Rev. 02 Page : 29 of 60 Modulation Polarization 11b Vertical Test Freq. (MHz) 2437 Note 1: Emission Level (dBuV/m) = SA Reading (dBuV/m) + Factor* (dB)

*Factor includes antenna factor , cable loss and amplifier gain Note 2: Margin (dB) = Emission level (dBuV/m) Limit (dBuV/m). Report No.: FR391801 Report Version: Rev. 02 Page : 30 of 60 Modulation Polarization 11b Horizontal Test Freq. (MHz) 2462 Note 1: Emission Level (dBuV/m) = SA Reading (dBuV/m) + Factor* (dB)

*Factor includes antenna factor , cable loss and amplifier gain Note 2: Margin (dB) = Emission level (dBuV/m) Limit (dBuV/m). Report No.: FR391801 Report Version: Rev. 02 Page : 31 of 60 Modulation Polarization 11b Vertical Test Freq. (MHz) 2462 Note 1: Emission Level (dBuV/m) = SA Reading (dBuV/m) + Factor* (dB)

*Factor includes antenna factor , cable loss and amplifier gain Note 2: Margin (dB) = Emission level (dBuV/m) Limit (dBuV/m). Report No.: FR391801 Report Version: Rev. 02 Page : 32 of 60 3.5.6 Transmitter Radiated Unwanted Emissions (Above 1GHz) for 11g Modulation Polarization 11g Horizontal Test Freq. (MHz) 2412 Note 1: Emission Level (dBuV/m) = SA Reading (dBuV/m) + Factor* (dB)

*Factor includes antenna factor , cable loss and amplifier gain Note 2: Margin (dB) = Emission level (dBuV/m) Limit (dBuV/m). Report No.: FR391801 Report Version: Rev. 02 Page : 33 of 60 Modulation Polarization 11g Vertical Test Freq. (MHz) 2412 Note 1: Emission Level (dBuV/m) = SA Reading (dBuV/m) + Factor* (dB)

*Factor includes antenna factor , cable loss and amplifier gain Note 2: Margin (dB) = Emission level (dBuV/m) Limit (dBuV/m). Report No.: FR391801 Report Version: Rev. 02 Page : 34 of 60 Modulation Polarization 11g Horizontal Test Freq. (MHz) 2437 Note 1: Emission Level (dBuV/m) = SA Reading (dBuV/m) + Factor* (dB)

*Factor includes antenna factor , cable loss and amplifier gain Note 2: Margin (dB) = Emission level (dBuV/m) Limit (dBuV/m). Report No.: FR391801 Report Version: Rev. 02 Page : 35 of 60 Modulation Polarization 11g Vertical Test Freq. (MHz) 2437 Note 1: Emission Level (dBuV/m) = SA Reading (dBuV/m) + Factor* (dB)

*Factor includes antenna factor , cable loss and amplifier gain Note 2: Margin (dB) = Emission level (dBuV/m) Limit (dBuV/m). Report No.: FR391801 Report Version: Rev. 02 Page : 36 of 60 Modulation Polarization 11g Horizontal Test Freq. (MHz) 2462 Note 1: Emission Level (dBuV/m) = SA Reading (dBuV/m) + Factor* (dB)

*Factor includes antenna factor , cable loss and amplifier gain Note 2: Margin (dB) = Emission level (dBuV/m) Limit (dBuV/m). Report No.: FR391801 Report Version: Rev. 02 Page : 37 of 60 Modulation Polarization 11g Vertical Test Freq. (MHz) 2462 Note 1: Emission Level (dBuV/m) = SA Reading (dBuV/m) + Factor* (dB)

*Factor includes antenna factor , cable loss and amplifier gain Note 2: Margin (dB) = Emission level (dBuV/m) Limit (dBuV/m). Report No.: FR391801 Report Version: Rev. 02 Page : 38 of 60 3.5.7 Transmitter Radiated Unwanted Emissions (Above 1GHz) for HT20 Modulation Polarization HT20 Horizontal Test Freq. (MHz) 2412 Note 1: Emission Level (dBuV/m) = SA Reading (dBuV/m) + Factor* (dB)

*Factor includes antenna factor , cable loss and amplifier gain Note 2: Margin (dB) = Emission level (dBuV/m) Limit (dBuV/m). Report No.: FR391801 Report Version: Rev. 02 Page : 39 of 60 Modulation Polarization HT20 Vertical Test Freq. (MHz) 2412 Note 1: Emission Level (dBuV/m) = SA Reading (dBuV/m) + Factor* (dB)

*Factor includes antenna factor , cable loss and amplifier gain Note 2: Margin (dB) = Emission level (dBuV/m) Limit (dBuV/m). Report No.: FR391801 Report Version: Rev. 02 Page : 40 of 60 Modulation Polarization HT20 Horizontal Test Freq. (MHz) 2437 Note 1: Emission Level (dBuV/m) = SA Reading (dBuV/m) + Factor* (dB)

*Factor includes antenna factor , cable loss and amplifier gain Note 2: Margin (dB) = Emission level (dBuV/m) Limit (dBuV/m). Report No.: FR391801 Report Version: Rev. 02 Page : 41 of 60 Modulation Polarization HT20 Vertical Test Freq. (MHz) 2437 Note 1: Emission Level (dBuV/m) = SA Reading (dBuV/m) + Factor* (dB)

*Factor includes antenna factor , cable loss and amplifier gain Note 2: Margin (dB) = Emission level (dBuV/m) Limit (dBuV/m). Report No.: FR391801 Report Version: Rev. 02 Page : 42 of 60 Modulation Polarization HT20 Horizontal Test Freq. (MHz) 2462 Note 1: Emission Level (dBuV/m) = SA Reading (dBuV/m) + Factor* (dB)

*Factor includes antenna factor , cable loss and amplifier gain Note 2: Margin (dB) = Emission level (dBuV/m) Limit (dBuV/m). Report No.: FR391801 Report Version: Rev. 02 Page : 43 of 60 Modulation Polarization HT20 Vertical Test Freq. (MHz) 2462 Note 1: Emission Level (dBuV/m) = SA Reading (dBuV/m) + Factor* (dB)

*Factor includes antenna factor , cable loss and amplifier gain Note 2: Margin (dB) = Emission level (dBuV/m) Limit (dBuV/m). Report No.: FR391801 Report Version: Rev. 02 Page : 44 of 60 3.5.8 Transmitter Radiated Unwanted Emissions (Above 1GHz) for HT40 Modulation Polarization HT40 Horizontal Test Freq. (MHz) 2422 Note 1: Emission Level (dBuV/m) = SA Reading (dBuV/m) + Factor* (dB)

*Factor includes antenna factor , cable loss and amplifier gain Note 2: Margin (dB) = Emission level (dBuV/m) Limit (dBuV/m). Report No.: FR391801 Report Version: Rev. 02 Page : 45 of 60 Modulation Polarization HT40 Vertical Test Freq. (MHz) 2422 Note 1: Emission Level (dBuV/m) = SA Reading (dBuV/m) + Factor* (dB)

*Factor includes antenna factor , cable loss and amplifier gain Note 2: Margin (dB) = Emission level (dBuV/m) Limit (dBuV/m). Report No.: FR391801 Report Version: Rev. 02 Page : 46 of 60 Modulation Polarization HT40 Horizontal Test Freq. (MHz) 2437 Note 1: Emission Level (dBuV/m) = SA Reading (dBuV/m) + Factor* (dB)

*Factor includes antenna factor , cable loss and amplifier gain Note 2: Margin (dB) = Emission level (dBuV/m) Limit (dBuV/m). Report No.: FR391801 Report Version: Rev. 02 Page : 47 of 60 Modulation Polarization HT40 Vertical Test Freq. (MHz) 2437 Note 1: Emission Level (dBuV/m) = SA Reading (dBuV/m) + Factor* (dB)

*Factor includes antenna factor , cable loss and amplifier gain Note 2: Margin (dB) = Emission level (dBuV/m) Limit (dBuV/m). Report No.: FR391801 Report Version: Rev. 02 Page : 48 of 60 Modulation Polarization HT40 Horizontal Test Freq. (MHz) 2452 Note 1: Emission Level (dBuV/m) = SA Reading (dBuV/m) + Factor* (dB)

*Factor includes antenna factor , cable loss and amplifier gain Note 2: Margin (dB) = Emission level (dBuV/m) Limit (dBuV/m). Report No.: FR391801 Report Version: Rev. 02 Page : 49 of 60 Modulation Polarization HT40 Vertical Test Freq. (MHz) 2452 Note 1: Emission Level (dBuV/m) = SA Reading (dBuV/m) + Factor* (dB)

*Factor includes antenna factor , cable loss and amplifier gain Note 2: Margin (dB) = Emission level (dBuV/m) Limit (dBuV/m). Report No.: FR391801 Report Version: Rev. 02 Page : 50 of 60 3.6 Emissions in non-restricted frequency bands 3.6.1 Emissions in non-restricted frequency bands limit Peak power in any 100 kHz bandwidth outside of the authorized frequency band shall be attenuated by at least 30 dB relative to the maximum in-band peak PSD level in 100 kHz 3.6.2 Measuring Instruments Refer a test equipment and calibration data table in this test report. 3.6.3 Test Procedures Reference level measurement 1. Set RBW=100kHz, VBW = 300kHz , Detector = Peak, Sweep time = Auto 2. Trace = max hold , Allow Trace to fully stabilize 3. Use the peak marker function to determine the maximum PSD level Emission level measurement 1. Set RBW=100kHz, VBW = 300kHz , Detector = Peak, Sweep time = Auto 2. Trace = max hold , Allow Trace to fully stabilize 3. Scan Frequency range is up to 25GHz 4. Use the peak marker function to determine the maximum amplitude level 3.6.4 Test Setup Transmitter Radiated Bandedge Emissions

. Test Result of Emissions in non-restricted frequency bands 3.6.5 This test item is performed on each TX output individually without summing or adding 10 log(NANT) since measurements are made relative to the in-band emissions on the individual outputs. Only worst test result of each operating mode is presented. Report No.: FR391801 Report Version: Rev. 02 Page : 51 of 60 3.6.6 Unwanted Emissions into Non-Restricted Frequency Bands 802.11b Reference Level TX 2412 MHz / 30MHz~25GHz (down 30dBc)

---

---

Report No.: FR391801 Report Version: Rev. 02 Page : 52 of 60 TX 2437 MHz / 30MHz~25GHz (down 30dBc) TX 2462 MHz / 30MHz~25GHz (down 30dBc) Report No.: FR391801 Report Version: Rev. 02 Page : 53 of 60 802.11g Reference Level TX 2412 MHz / 30MHz~25GHz (down 30dBc)

---

---

Report No.: FR391801 Report Version: Rev. 02 Page : 54 of 60 TX 2437 MHz / 30MHz~25GHz (down 30dBc) TX 2462 MHz / 30MHz~25GHz (down 30dBc) Report No.: FR391801 Report Version: Rev. 02 Page : 55 of 60 802.11n HT20 Reference Level TX 2412 MHz / 30MHz~25GHz (down 30dBc)

--

---

Report No.: FR391801 Report Version: Rev. 02 Page : 56 of 60 TX 2437 MHz / 30MHz~25GHz (down 30dBc) TX 2462 MHz / 30MHz~25GHz (down 30dBc) Report No.: FR391801 Report Version: Rev. 02 Page : 57 of 60 802.11n HT40 Reference Level Tx 2422MHz / 30MHz~25GHz (down 30dBc)

---

---

Report No.: FR391801 Report Version: Rev. 02 Page : 58 of 60 Tx 2437MHz / 30MHz~25GHz (down 30dBc) Tx 2452 / 30MHz~25GHz (down 30dBc) Report No.: FR391801 Report Version: Rev. 02 Page : 59 of 60 Test laboratory information 4 Established in 2012, ICC provides foremost EMC & RF Testing and advisory consultation services by our skilled engineers and technicians. Our services employ a wide variety of advanced edge test equipment and one of the widest certification extents in the business. International Certification Corp, it is our definitive objective is to institute long term, trust-based associations with our clients. The expectation we set up with our clients is based on outstanding service, practical expertise and devotion to a certified value structure. Our passion is to grant our clients with best EMC / RF services by oriented knowledgeable and accommodating staff. Our Test sites are located at Linkou District and Kwei Shan Hsiang. Location map can be found on our website http://www.icertifi.com.tw. Linkou Tel: 886-2-2601-1640 No. 30-2, Ding Fwu Tsuen, Lin Kou District, New Taipei City, Taiwan, R.O.C. If you have any suggestion, please feel free to contact us as below information Tel: 886-3-271-8666 Fax: 886-3-318-0155 Email: ICC_Service@icertifi.com.tw END Kwei Shan Tel: 886-3-271-8666 No. 3-1, Lane 6, Wen San 3rd St., Kwei Shan Hsiang, Tao Yuan Hsien 333, Taiwan, R.O.C. Report No.: FR391801 Report Version: Rev. 02 Page : 60 of 60