Blinds Chain Controller Mobile Version Character 1 2 3 4 5 6 No change of existing blinds , no tubular motor. One touch , manual to motor;
WIFI connector: work with google home , Alexa amazon Yandex etc directly;
Schedule: Setting open and close time as your like, open when sun rise, and close when sunset;
Long distance : open or close yourhome blinds on office or business with Wifi on ;
Easy mounting and setting : 3-5 minutes DIY on your fingertip position;
Control: Mobile and remote both can ;
1 Open Motor and Choose Blinds Direction 1 2 3 Open motor: Power adapter to wall outlet , cable to the device. Slide mini switch. Chain position: Left direction: Facing blinds, chain/rope on left hand. Right direction: Facing blinds, chain/rope on right hand. Slide mini switch on the bottom to same direction as chain. when switch sliding, light on surface shine from blue-green-red and stay on red. please be careful claiming this step as the switch is fragile. After complete APP connecting, you can also change motor direction by selecting motor direction from the more submenu. 2 Device In Pairing Mode For Network Discover 1 Search and download "Tuya Smart" in major application markets or scan the"QR code"below to download the App, https://en.tuya.com/
2 Open "
Tuya smart" or "
Smart life", and connector with motor;
Note: pls move carefully for mini button , as it can break easily. Small home appliance Add device Add device Curtain Confirm indicator Rapidly blink Sweep Downloads APP Add device Successfully Open
"Smart life"
Press
"Add device"
Or "Tuya Smart" App Or "+" on upper right corner Select Small home appliance"
motor--Curtain (wifi)Input your Wifi address and password (note:
wifi must be 2.4GHz band). Mobile: Confirm the indicator is blinking rapidly Push and hold the Up Arrow ( left ) & Stop button (middle) until Up Arrow starts flashing in blue (about 5 - 8 seconds). press confirm indicator rapidly blink in mobile. added!
Note:
1) The motor will no response after APP connector until step 4: Set Limits On The Device;
2) Pls make sure that the Limits setting is prior to any APP control of motor. Photo 1 Suitable gear and chain 3 Mounting 1 2 3 4 5 Pull down on the blinds, hang Installation mode 1:
Installation mode 2:
the supplied card on bottom of 3M Adhensive, To keep it Replace the card with mounting more stronger, advice bracket ,The whole on mounting mounting bracket stick on bracket aligned marked 3m adhensive at least 12 position, Fix screw on the hole;
hours before using. two position for choose: flat or back page). side. Open device back,Press up board outside, put suitable gear on, take chain around gear, close device backing ( Suitable gear pls ref photo 1: bottom on Tight chain on the motor , put motor slide groove down, until motor lock on groove, pls choose reasonable chain tension. chain, please note chain is straight and tight. According the chain position, mark L or R on the hole,
( pls note card outside of the bottom bar ). Note: Pls be sure use the suitable gear for the chain ( ref photo1 ), and adjust the tension , otherwise will noisy. 4 Set Limits On The Device Push the Up Arrow (left button) reach high limit position, Push shade stop,push and hold the Once the red light flashes, push until the shades open all the way. the Stop Button and release. Stop Button until the red light the Down Arrow until the flashes (about 5 seconds) shades reach low limit position. Hit the stop button when they are completely closed. The device will wait a few seconds then flash. Done!
Now, the device will automatically stop at the pre-set upper and lower limits. If the range changes please reset the limits. 5 Function Setting 6 Reset And Remove Device 1 Schedule: Can setting time as you like , Open when sunrise and close when sunset. Step 2:
Device added successfully More Schedule 2 Voice control Smart life Welcome home upper right conner Push UP &Down Arrow about 12 seconds, until the light flashes from redbluegreen 2-3 times , release , press stop button , reset device finish. Parameters Top up the projection on bottom, slide upon groove, open upback board and take out chain. Remove button 3 Connector with google Alexa etc Tuya Welcome home google Assistant , Yandex etc. me more service Alexa , More Name BLINDS CONTROLLER Control Method MOBILE or REMOTE 4 Device pair not only with mobile , but also remote push and hold the Stop Once its flashing, It will flash the lights, Button (middle button) push the up button and the remote is until the red light flashes on the remote. paired.
(about 5 seconds), Torque 1.35N.m Speed 55rpm Frequency 2.4GHz 433MHz Voltage 12V ADAPTER VOLTAGE 110V-240V Rated Current 1.2A Max Blinds Size 8FT(2.5M)*12FT(3.5M) Max Weight 10KG Battery
(optional) 12V/1200mAH Distance No limit , ask for good wifi signal Compatible Directly connector with google home , alexa etc FCC WARNING This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
-- Reorient or relocate the receiving antenna.
-- Increase the separation between the equipment and receiver.
-- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-- Consult the dealer or an experienced radio/TV technician for help. To maintain compliance with FCCs RF Exposure guidelines, This equipment should be installed and operated with minimum distance between 20cm the radiator your body: Use only the supplied antenna.