FCC ID: 2AQURZW39SU Z-Wave Mini Smart Dimmer Plug

MP21ZD SIZE: 190 x 190 mm 80G 47 x 47 mm Z-Wave Dimmer plug MP21ZD (ZW39SU) Specification Input: 125VAC 60Hz Frequency: 908.42 MHz Loading: 200W Incandescent 100W Dimmable CFL/LED Indoor use in dry location LED indicator Blue: Light status indicator Blue: ADD / Inclusion Purple: Remove / Exclusion Program button Press 1x: Manually Red: Network Failure / Over-temperature Warning Press 3x: Z-Wave Network configuration Reset: Press the button twice then hold it for 10 seconds is functional--single press can turn on / off the lamp. To Remove The Device:

5. S2 security and 700 Z-Wave chip for reliable wireless communication. Host reset: Remove it from hub the device will be restore to factory default. Z-WAVE INTEROPERABILITY Overloading Warning Warranty This product can be included and operated in any Z-Wave network with other Z-Wave certified devices from other manufa-

Our Products warrant this product to be free from manufacturing defects for a period of one year from the original date of cturers and/or other applications. All non-battery operated nodes within the network will act as repeaters regardless of consumer purchase. This warranty is limited to the repair or replacement of this product only and does not extend to cons-

vendor to increase the reliability of the network. This Device supports Lifeline (association group 1) supporting 1 node for equential or incidental damage to other products that may be used with this product. This warranty is in lieu of all other war-

lifeline communication. Group 1 must be assigned the Node ID of the primary controller where unsolicited notifications will ranties, expressed or implied. Some states do not allow limitations on how long an implied warranty lasts or permit the excl-

be sent. The Z-Wave controller should set this association automatically after inclusion. Lifeline association only supports the usion or limitation of incidental or consequential damage, so the above limitations may not apply to you. This warranty gives Features:

1. Z-Wave on / off + dimmer control. 2. Grounded 3-wire power connection for safety. 3. Remember and restore on/off status after power failure. 4. Built-in Z-Wave Plus signal repeater to extend network range. 6. Work with all certificated Z-Wave controllers. Please contact us if you have any questions:

www.minoston.com ask@minoston.com Device Reset Locally function. Adding Device To Z-Wave Network for QR CODE Scan here for SmartStar inclusion Note: DSK Code can be found on the packaging box. Do not remove or damage them. Notes:

1. Plug the device you want to control into the Z-Wave Smart plug controlled outlet. NOTE: Plug directly into the outlet, do not use with power strip. 2. Your device may need to be within 100 feet of the controller to be included. If so, include the device to the network within 10 feet of the controller and relocate it to the desired position in your home. Be sure to refresh the network if the device is included in this manner. 100 feet Adding Device To Z-Wave Network Z-Wave Network Configuration 1. Follow the instructions for your Z-Wave certified controller to add a device to the Z-Wave network. 2. Once the controller is ready to add your device, press the Manual/ Program button on the smart plug 3 times quickly. The blue LED will blink quickly. Auto-add mode: LED will blink within 30 seconds after first plugged in. Now, you have complet-

ed control to turn your fixture ON/OFF according to groups, schedules and interactive automation programmed by your controller. If your Z-Wave certified controller features remote access, you can control your fixture from your mobile devices. Again: If you have issues with pairing / including, please move the device as close as possible to the hub and try again--you can move to your final location when completed. Note: If the manual button doesn't light up after pressed 3 times, please reset the Device: click the button twice quickly then hold for at least 10 seconds. This operation could be done when manual control 1. Follow the instructions for your Z-Wave certified controller to remove a device from the Z-Wave network. 2. Once the controller is ready to remove your device, press the manual/program button on the smart plug 3 times quickly. If you'd like to reset the KWH record, just click the button 10 times very quickly. Network exclusion or factory reset will KWH Reset:

NOT automatically erase the KWH data. To Return The Device To Factory Defaults:

Manual: Click the button twice quickly then hold for at least 10 seconds. (Light flashes once when reset successfully.) Association Group:

Group 1 supports 1 node ID,Group 2 Supports maximum of 5 node IDs Association Group 1: Z-Wave Plus Lifeline Association Group 2: Send Basic Set ON / Off Over-temperature protection is protection against overheating of the protected equipment. When the device's temperature is high, the LED will light up in red and cut down the power. Please power off the device and use it after the temperature of the device drops. you specific rights, and you may also have other rights which vary from state to state. Parameter Settings LED Indicator This parameter can access you to choose the LED indicator to be on when the plug(light) is on/off, or LED indicator remains on/off all times. (LED flashes 3 times when the configuration parameter changed.)

--- Parameter =2, size =1byte, Default =0 Value=0 (default) LED is On when switch (light) is On. Value=1 --- LED is On when switch (light) is Off. Value=2 --- LED is always Off. Value=3 --- LED is always On. Auto Turn-Off Timer This parameter can access you to set a timer to make the switch turn off automatically after the switch turns on. The numberentered as value corresponds to number of minutes. Operation: Set up on the hub.

(LED flashes 3 times when the configuration parameter changed.)

--- Parameter =4, Size=4Value: 0 65535(minutes);

Value=0(default) disable FCC / IC This device complies with part 15 of the FCC and Industry Canada license-exempt RSS standard(s). Operation is subjected to the following two conditions: (1) This device may not cause harmful interference, (2) This device must accept any interference received, including interference that may cause undesired operation. FCC NOTE: The manufacturer is not responsible for any radio or TV interference caused by unauthorized modications to this equipment. Such modications could void the users authority to operate the equipment. Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio / TV technician for help. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential ins-

tallation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions may cause harmful interference to radio communications. However, there is no guarantee that interfe-

nce will not occur in a particular installation. If this equipment does cause harmful interference to radio or television recepre-

tion, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

CAUTION - PLEASE READ!

This device is intended for installation in accordance with the National Electric Code and local regulations in the United States, or the Canadian Electrical Code and local regulations in Canada If you are unsure or uncomfortable about performing this installation consult a qualied electrician. WARNING RISK OF FIRE / RISK OF ELECTRICAL SHOCK / RISK OF BURNS TO REDUCE THE RISK OF ELECTRIC SHOCK, THIS PRODUCT HAS A GROUN-

DING TYPE PLUG THAT HAS A THIRD (GROUNDING) PIN. THIS PLUG WILL ONLY FIT INTO A GROUNDING TYPE POWER OUTLET. IF THE PLUG DOES NOT FIT INTO THE OUTLET, CONTACT A QUALIFIED ELECTRICIAN TO INSTALL THE PROPER OUTLET. DO NOT CHANGE THE PLUG IN ANY WAY. CONTROLLING APPLIANCES:

CAUTION: TO REDUCE THE RISK OF OVERHEATING AND POSSIBLE DAMAGE TO OTHER EQUIPMENT DO NOT EXCEED RATINGS DO NOT USE TO CONTROL ANY DEVICE WHERE UNINTENDED OPERATION COULD CAUSE UNSAFE CONDITIONS (HEAT LAMP, SUN LAMP, ETC.) MEDICAL EQUIPMENT Please DO NOT use this switch to control Medical or Life Support equipment. Z-Wave devices should never be used to control the On / Off status of Medical and / or Life Support equipment. CONTROLLING APPLIANCES Please exercise EXTREME CAUTION when using Z-Wave devices to control appliances. Reason being is because the appli-

ance you want to control may be in a separate room and if unintentional behavior occurs (such as adevice turning on or off -

either intentionally via schedules, or unintentionally via network error) this event may lead to a hazardous condition. For these reasons, please note the following suggestions:

1) Do not include Z-Wave devices in Groups or Scenes if they control appliances. 2) Do not use Z-Wave devices to control electric heaters or any other appliances which may present a hazardous condition due to unattended, unintentional, or automatic power control. Command Class Information GRNERIC DEVICE CLASS: 0x10 - SWITCH BINARY SPECIFIC DEVICE CLASS: 0x00 NOT_USED COMMANDCLASS:

0x5E - ZWAVEPLUS_INFO 0x25 - SWITCH_BINARY 0x70 - CONFIGURANTION 0x72 - COMMAND_CLASS_MANUFACTURER_SPECIFIC 0x5A - COMMAND_CLASS_DEVICE_RESET_LOCALLY 0x85 - COMMAND_CLASS_ASSOCIATION 0x87 - COMMAND_CLASS_INDICATOR 0x8E - COMMAND_CLASS_MULTI_CHANNEL_ASSOCIATION 0x73 - COMMAND_CLASS_POWERLEVEL 0x59 - COMMAND_CLASS_ASSOCIATION_GRP_INFO 0x9F - COMMAND_CLASS_SECURITY_2 0x55 - COMMAND_CLASS_TRANSPORT_SERVICE 0x6C - COMMAND_CLASS_SUPERVISION 0x86 - COMMAND_CLASS_VERSION 0x7A - COMMAND_CLASS_FIRMWARE_UPDATE_MD Auto Turn-On Timer This parameter can access you to set a timer to make the switch turn on automatically after the switch turned on. The numberentered as value corresponds to number of minutes. Operation: Set up on the hub.

(LED flashes 3 times when the configuration parameter changed.)

--- Parameter =6, Size=4Value: 0 65535(minutes);

Value=0(default) disable turn on the outlet Night Light Set This parameter can access you to set a specific brightness for the light when you want to make it as a night light.

(LED flashes 3 times when the configuration parameter changed.)

--- Parameter =7, Size=1, Default = 2 Value=1 --- 10% brightness Value=2 --- 20% brightness Value=10 --- 100% brightness Restores state after power failure This parameter can access you to set the switch to be on/off after power failure. Operation: quickly press 8 times to change this parameter.

(LED flashes 3 times when the configuration parameter changed.) Parameter=8Size=1Value=2(default) Value=0 --- The switch is off regardless of the state prior to power failure. Value=1 --- The switch is on regardless of the state prior to power failure. Value=2(default) memory state before power failure This switch will be return to state prior to the power failure after power is restored. Dimmer speed (ON/OFF Control) This parameter can access you to set the time from maximum brightness to minimum brightness or minimum brightness to This parameter can access you to set the time from maximum brightness to minimum brightness or minimum brightness to

maximum brightness (Only when turn ON / OFF the light ) Operation: Set up on the hub.

(LED flashes 3 times when the configuration parameter changed.) Parameter=9Size=1, Default = 2 Value=0 --- instant on/off Value=1--- from 0x63 to 0x00 or from 0x00 to 0x63 need 1s Value=2 --- from 0x63 to 0x00 or from 0x00 to 0x63 need 2s Value=10 --- from 0x63 to 0x00 or from 0x00 to 0x63 need 10s Dimmer speed (Dimmer Control) maximum brightness.

(Only when hold it to change the brightness or control from HUB). Operation: Set up on the hub.

(LED flashes 3 times when the configuration parameter changed.) Parameter=10Size=1, Default = 4 Value=1 --- from 0x63 to 0x00 or from 0x00 to 0x63 need 1s Value=2 --- from 0x63 to 0x00 or from 0x00 to 0x63 need 2s Value=10 --- from 0x63 to 0x00 or from 0x00 to 0x63 need 10s Multilevel minimum value can be set Operation: quickly press 5 times to change this parameter.

(LED flashes 3 times when the configuration parameter changed.)

---Parameter=11Size=1Default = 10 Value=0 --- disable Multilevel maximum value can be set Operation: quickly press 10 times to change this parameter.

(LED flashes 3 times when the configuration parameter changed.)

---Parameter=12Size=1Default = 99 Value=0 --- disable Value=1 Value=99 Value=1 Value=99

Z-Wave Dimmer plug MINOsTON

@ilMI|

Made in China ZH09 DvAszT anduy WW FCCID: 2AQURZW39SU Date:

ZHWN 2806 Ouanbaiy For indoor use Loading: 200W incandescent

-100W Dimmable CFL/LED CA En HTT AT TTT 20 30 40 50 60 70 80 20140 i i My ROSLO- mi 8hteonn 10 20 30 40 50 60 70 80 9010 LivvtinvsTivvativvatioeelavcetineelssvstusnduned

| 74 I]

yuna gucinyeuey ty 10409 90 80 70 60 50 70 60 50 40 30 20 10 mm IVONTVNTNNTVOATOTVONTOR COTTON Ona 70 60 50 40 30 IVTTUNITTONTCUNTONTINN 20 10100 90 80 NA it

C5266091_X10_Ed.2 NIE-TECH Co., Ltd Date: 2022-07-23 Office of Engineering Technology Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 Subject: Request for Confidentiality FCC ID: 2AQURZW39SU To Whom It May Concern, Pursuant to the provisions of Sections 0.457 and 0.459 of Commission's rules

(47CFR0.457, 0.459), we are requesting the Commission to withhold the following attachment(s) as confidential document from public disclosure. Exhibits ID Label/Location Attestation Statement External Photos Block Diagram Schematics Test Report Test Setup Photos Users Manual Internal Photos Parts List / Tune Up RF Exposure Info Operational Description Cover Letter(s) SDR Software / Security Info Long-Term Confidentiality No No No No No NOTE 1 NOTE 1 No No Short-Term Confidentiality NOTE 2 No No No No No No NOTE 1: Long-Term Confidentiality may be permitted under special conditions (See II. LONG-TERM CONFIDENTIALITY, Section 3 of KDB 726920, use last in force) NOTE 2: Short-Term Confidentiality can be requested for a maximum of 180 days from the date of the grant. Above mentioned document contains detailed system and equipment description are considered as proprietary information in operation of the equipment. The public disclosure of above documents might be harmful to our company and would give competitor an unfair advantage in the market. In case of short-term Confidentiality, the applicant requests the exhibits selected above are withheld from public view for a period of days from the date of the Grant of Equipment Authorization and prior to marketing. It is our understanding that all measurement test reports, FCC ID label format and correspondent during certification review process cannot be granted as confidential documents and those information will be available for public review once the grant of equipment authorization is issued. Sincerely, 1/1 C5266091_X10_Ed.2 Signature:

Name:Jianghai Nie Title:Manager 1/1

Declaration on model difference We, Z-Wave Mini Smart Dimmer Plug, the undersigned hereby confirm that these models are identical, and all models have the same RF module and Antenna, except for selling different brands. Product name Z-Wave Mini Smart Dimmer Plug Model No. ZW39SU,MP21ZD Trade name Ministon FCC ID INPUT 2AQURZW39SU AC 125V/60Hz Confirmed by:

Clients signature:

Date:2022-07-23 Clients name / title: Jianghai Nie/Manager Page 1 of 1

C5266091_X8_Ed.1 Letter of Authorization NIE-TECH Co., Ltd Company: NIE-TECH Co., Ltd Address: Jinlian commercial center 9001, Jinxiu road No.273, Changan Town,Dongguan City, GuangDong Prov., CHINA Product Name: Z-Wave Mini Smart Dimmer Plug Model Number: ZW39SU, MP21ZD FCC Identifier:2AQURZW39SU We authorize LGAI Technological Center S.A., Ronda de la Font del Carme, s/n, 08193 Bellaterra, Spain, to act on our behalf on all matters concerning the above named equipment. Any individual within LGAI Technological Center S.A. is authorized to act on our behalf and take action on the application. We declare that authorize LGAI Technological Center S.A., Ronda de la Font del Carme, s/n, 08193 Bellaterra, Spain, is allowed to forward all information related to the approval project to the Federal Communication Commission and to discuss any issues concerning the approval application. Any and all acts carried out by LGAI Technological Center S.A. on our behalf shall have the same effect as acts of our own. Name: Jianghai Nie Date: 2022-07-23 Title: Manager Signature of applicant:

1/1