FCC ID: 2AQURZW38SU-V8 Z-Wave Mini Smart Plug

MP21ZP SIZE: 235 x 285 mm 80G 47 x 47.5 mm Z-Wave Plug with Energy Monitor(800S) MP21ZP Specication Input: 125VAC 60Hz Frequency: 908.42 MHz Loading: 15A 1875W RESISTIVE OR GENERAL PURPOSE 10A MAX 1250W TUNGSTEN 1/2 HP Indoor use in dry location LED indicator Blue: Light status indicator Blue: ADD / Inclusion Purple: Remove / Exclusion Red: Network Failure Program button Press 1x: Manually Press 3x: Z-Wave Network conguration Reset: Press the button quickly and then hold the 3rd press for 10 seconds Features:

1. Z-Wave control on/ o. 2. Z-Wave controlled AC outlet for standard incandescent lighting, CFL/LEDs, fansd or small appliances (1875W Resistive Max). 3. Grounded 3-wire power connection for safety. 4. Remembers and restores on / o status after power failure. 5. Built-in Z-Wave Plus signal repeater to extend network range. 6. S2security and 800 Z-Wave chip for reliable wireless communication. 7. Work with all certicated Z-Wave controllers. 8. Protection function(When the protection function is triggered, it needs to be powered the device on again for normal use.) Voltage protection: when the voltage>135V, the device will be forcibly shut down Current protection, when the current>16A, the device will be forcibly shut down Power Wattage protection, when the power>2000W, the device will be forcibly shut down. Please contact us if you have any questions:

www.minoston.com ask@minoston.com Z-WAVE INTEROPERABILITY This product can be included and operated in any Z-Wave network with other Z-Wave certied devices from other manufacturers and/or other applications. All non-battery operated nodes within the network will act as repeaters regardless of vendor to increase the reliability of the network. This Device supports Lifeline (association group 1) supporting 1 node for lifeline communication. Group 1 must be assigned the Node ID of the primary controller where unsolicited notications will be sent. The Z-Wave controller should set this association automatically after inclusion. Lifeline association only supports the "Device Reset Locally" function. Adding Device To Z-Wave Network for QR CODE Scan here for SmartStar inclusion Note: FULL DSK can be found on the packaging box. Do not remove or damage them. Notes:

1. Plug the device you want to control into the Z-Wave Smart plug controlled outlet NOTE: Plug directly into the outlet, do not use with power strip. Z-Wave Network Conguration Adding Device To Z-Wave Network 1. Follow the instructions for your Z-Wave certied controller to add a device to the Z-Wave 2. Once the controller is ready to add your device, press the Manual/ Program button on the smart plug 3 times quickly. Z-Wave Long Range Note:MP21ZP Support Z-Wave Long Range Z-Wave Long Range device can only support be included via SmartStart.Extract the DSK from end device and paste it into the Dsk Value in PC Controller, make sure the long Range' option is ticked. To Remove The Device 1. Follow the instructions for your Z-Wave certied controller to remove a device from the Z-Wave network. 2. Once the controller is ready to remove your device, press the manual / program button on the smart plug 3 times quickly. The green light is on for 2s when the removal is successful. To Return The Device To Factory Defaults Manual: Press the button quickly and then hold the 3rd press for 10 seconds. Host reset: Remove it from hub, the device will be restore to factory default. Association Group

(LED ashes twice when the conguration parameter changed.) Support 2 groups, each group max support 5 devices Group 1 lifeline Group 2 Left outlet send basic set. Regarding SmartThings usage exceptions:

If the SmartThings replacement service results in abnormal use of the product, please install a new driver(edge driver) according to the following solutions.

(SmartThings driver subscription channel)

(guide video) 1. Scan the above QR code(left)to open the SmartThings Edge Driver subscription channel f the product. 2. Log in to the SmartThings account after opening the SmartThings Edge Driver subscription channel. 3. Select the SmartThings Hub you are using, and click "Enroll". 4. After "Enroll" is completed, click "Available Drivers". 5. After entering the "Available Drivers" page, select "Z-Wave Switch" to "Install". Note: Please scan the QR code on the right to view the guide video. Value=1 --- Disable power report Parameter Settings Locally Button Press function:

1: press 1x: turn output ON or OFF 2: quickly press 3x: inclusion or exclusion 3: quickly press 5x: change Parameter 1 4: quickly press 8x: change Parameter 4 5: quickly press 10x: Reset KWH 6: Manual: Press the button quickly and then hold the 3rd press for 10 seconds. LED Indicator This parameter can access you to choose the LED indicator to be on when the plug (light) is on / o, or LED indicator remains on / o all times. Operation: quickly press 5 times to change

(LED ashes 3 times when the conguration parameter changed.)

--- Parameter=1, size=1byte, Default=0 Value=0 (default) LED is On when the switch(light) is On. Value=1 --- LED is On when switch(light) is O. Value=2 --- LED is always O. Value=3 --- LED is always On. Auto Turn-O Timer This parameter can access you to set a timer to make the switch turn o automatically after the switch turned on. The numberentered as value corresponds to number of minutes. 2. Your device may need to be within 100 feet of the controller to be included. If so, desired position in your home. Be sure to refresh the network if the device is included in this manner. 100 feet Operation: Set up on the hub.

(LED ashes 3 times when the conguration parameter changed.)

---Parameter=2, Size=4, Value: 0-65535 (minutes);

Value=0 (default) disable Auto Turn-On Timer This parameter can access you to set a timer to make the switch turn on automatically after the switch turned o. The numberentered as value corresponds to number of minutes. Operation: Set up on the hub.

(LED ashes 3 times when the conguration parameter changed.) Parameter=3, Size=4, Value: 0 65535 (minutes);

Value=0 (default) disable Restores state after power failure This parameter can access you to set the switch to be on / o after power failure. Operation: quickly press 8 times to change this parameter .

(LED ashes 3 times when the conguration parameter changed.) Parameter=4, Size=1, Value=0(default) Value=0(default) memory state before power failure. Value=1 --- The switch is o regardless of the state prior to power failure. Value=2 --- The switch is on regardless of the state prior to power failure. This switch will be return to state prior to the power failure after power is restored. Reports sending settings

(LED ashes 3 times when the conguration parameter changed.) Power Wattage(W) Report This parameter determines the minimum change in power wattage (W) that will result in sending new power report to the main controller. Parameter=5, size=1byte, value=5W (default) value range: 5 - 50W Time Report This parameter determines minimum time that has to elapse before sending new power report to the main controller. Parameter=6, size=4byte, value=5Minute (default) value range: 1 - 65535Minute Current(A) Report This parameter determines the minimum change in Current (A) that will result in sending new power report to the main controller. Parameter=7, size=1byte, Value=1: 0.1A (default) value range: (1~10) x0.1A value=1 --- 0.1A value=2 --- 0.2A value=3 --- 0.3A value=10 --- 1A Energy(KWH) Report This parameter determines the minimum change in consumed energy that will result in sending new energy report to the main controller. Parameter= 8, size=1byte, Value=1: 0.01KWH(default) value range: (1~100) x0.01KWH Value=1 --- 0.01KWH value=2 --- 0.02KWH value=3 --- 0.03KWH value=100 --- 1KWH Adjust LED brightness

(Green LED ashes twice to conrm the setting is successful.) Parameter=9, Size=1, Value=0 --- Bright Value=1 --- Medium Value=2 --- Low (default.) Power Report This parameter determines whether to enable or disable the power report. Parameter= 10, size=1byte, Default=0 Value=0 (Default)---Enable power report Current Report This parameter determines whether to enable or disable the current Parameter= 11, size=1byte, Default=0 Value=0 (Default) --- Enable current report Value=1 --- Disable current report Report Frequency of Current This parameter determines the interval minutes after the last report of the current. Parameter= 12, size=4byte, Value=60 Minutes (default) Value Range: 1-65535 Minutes Report Frequency of Voltage This parameter determines the interval minutes after the last report of the voltage. Parameter= 13, size=4byte, Default= 60 (Minutes) Value=0 --- disable the report FCC / IC This device complies with part 15 of the FCC and Industry Canada license-exempt RSS standard(s). Operation is subjected to the following two conditions:

(1) This device may not cause harmful interference,

(2) This device must accept any interference received, including interference that may cause undesired operation. FCC NOTE: The manufacturer is not responsible for any radio or TV interference caused by unauthorized modications to this equipment. Such modications could void the user's authority to operate the equipment. Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected. with Energy Monitor(800S) Consult the dealer or an experienced radio /TV technician for help. Specification Input: 125VAC 60Hz Frequency: 908.42 MHz Loading: 15A 1875W RESISTIVE OR GENERAL PURPOSE 5A MAX625W TUNGSTEN 1/3 HP Indoor use in dry location 2. Your device may need to be within 100 feet of the controller to be included. If so, include the device to the network within 10 feet of the controller and relocate it to the desired position in your home. Be sure to refresh the network if the device is included in this manner. 100 feet Z-Wave Plug Z-Wave Network Configuration MP31ZP 1. Follow the instructions for your Z-Wave certified controller to add a device to the Z-Wave network. LED indicator Blue: Light status indicator Blue: ADD / Inclusion Purple: Remove / Exclusion Red: Network Failure NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, Adding Device To Z-Wave Network pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment o and on, the user is Program button encouraged to try to correct the interference by one or more of the following measures:

Press 1x: Manually

-- Reorient or relocate the receiving antenna. Press 3x: Z-Wave Network configuration

-- Increase the separation between the equipment and receiver. Reset: Press the button twice then hold it

-- Connect the equipment into an outlet on a circuit dierent from that to which the receiver is for 10 seconds connected. Features:

-- Consult the dealer or an experienced radio/TV technician for help. Important note: To comply with the FCC RF exposure compliance requirements, no change to the antenna or the device is permitted. Any change to the antenna or the device could result in the device exceeding the RF exposure requirements and void user's authority to operate the device. 2. Z-Wave controlled AC outlet for standard incandescent lighting, CFL/LEDs, fans interactive automation programmed by your controller. or small appliances (1875W Resistive Max). 1. Z-Wave control on / off. from your mobile devices. 2. Once the controller is ready to add your device, press the Manual/ Program button on the smart plug 3 times quickly. The blue LED will blink quickly. Auto-add mode: LED will blink within 30 seconds after first plugged in. Now, you have completed control to turn your fixture ON/OFF according to groups, schedules and Again: If you have issues with pairing / including, please move the device as close as possible to the hub and try again--you can move to your final location when completed. Note: If the manual button doesn't light up after 3 pressed , please reset the Device: click the button twice quickly then hold for at least 10 seconds. This operation could be done when manual control is functional--single press can turn 3. Grounded 3-wire power connection for safety. CAUTION - PLEASE READ!

4. Remembers and restores on / off status after power failure. This device is intended for installation in accordance with the National Electric Code and local regulations in the United States, or the Canadian Electrical Code and local regulations in Canada If you are unsure or uncomfortable about performing this installation consult a qualied electrician. 5. Built-in Z-Wave Plus signal repeater to extend network range. 6. S2 security and for reliable wireless communication. To Remove The Device:

on / off the lamp. If your Z-Wave certified controller features remote access, you can control your fixture 1. Follow the instructions for your Z-Wave certified controller to remove a device from 2. Once the controller is ready to remove your device, press the manual/program again for normal use.) the Z-Wave network.

(When the protection function is triggered, it needs to be powered the device on Current protection, when the current16A, the device will be forcibly shut down Voltage protection: when the voltage135V, the device will be forcibly shut down 7. Work with all certificated Z-Wave controllers. WARNING 8. Protection function RISK OF FIRE /RISK OF ELECTRICAL SHOCK/ RISK OF BURNS TO REDUCE THE RISK OF ELECTRIC SHOCK, THIS PRODUCT HAS A GROUNDING TYPE PLUG THAT HAS A THIRD (GROUNDING) PIN. THIS PLUG WILL ONLY FIT INTO A GROUNDING TYPE POWER OUTLET. IF THE PLUG DOES NOT FIT INTO THE OUTLET, CONTACT A QUALIFIED ELECTRICIAN TO INSTALL THE PROPER OUTLET. DO NOT CHANGE THE PLUG IN ANY WAY. CONTROLLING APPLIANCES:

CAUTION: TO REDUCE THE RISK OF OVERHEATING AND POSSIBLE DAMAGE TO OTHER EQUIPMENT DO NOT EXCEED RATINGS Please contact us if you have any questions:

DO NOT USE TO CONTROL ANY DEVICE www.minoston.com WHERE UNINTENDED OPERATION COULD ask@minoston.com CAUSE UNSAFE CONDITIONS (HEAT LAMP, SUN LAMP, ETC.) Power Wattage protection, when the power2000W, the device will be forcibly

(Light flashes once when reset successfully.) button on the smart plug 3 times quickly. KWH Reset:

shut down. Association Group:

To Return The Device To Factory Defaults:

Manual: Click the button twice quickly then hold for at least 10 seconds. Host reset: Remove it from hub the device will be restore to factory default. If you'd like to reset the KWH record, just click the button 10 times very quickly. Network exclusion or factory reset will NOT automatically erase the KWH data. MEDICAL EQUIPMENT Please DO NOT use this switch to control Medical or Life Support equipment. Z-WAVE INTEROPERABILITY Z-Wave devices should never be used to control the On /O status of Medical and / or Life Support equipment. This product can be included and operated in any Z-Wave network with other Association Group 2: Send Basic Set ON / Off Association Group 1: Z-Wave Plus Lifeline Warranty Group 1 supports 1 node ID,Group 2 Supports maximum of 5 node IDs Our Products warrant this product to be free from manufacturing defects for a period of vendor to increase the reliability of the network. This Device supports Lifeline CONTROLLING APPLIANCES Z-Wave certified devices from other manufacturers and/or other applications. All Please exercise EXTREME CAUTION when using Z-Wave devices to control appliances. Reason being is non-battery operated nodes within the network will act as repeaters regardless of because the appliance you want to control may be in a separate room and if unintentional behavior occurs (such as adevice turning on or o - either intentionally via schedules, or unintentionally via network error) this event may lead to a hazardous condition. For these reasons, please note the following suggestions:

1) Do not include Z-Wave devices in Groups or Scenes if they control appliances. 2) Do not use Z-Wave devices to control electric heatersor any other appliances which may present a hazardous condition due to unattended, unintentional, or automatic power control.

(association group 1) supporting 1 node for lifeline communication. Group 1 must be assigned the Node ID of the primary controller where unsolicited notifications will be sent. The Z-Wave controller should set this association automatically after is in lieu of all other warranties, expressed or implied. inclusion. Lifeline association only supports the Device Reset Locally function. Some states do not allow limitations on how long an implied warranty lasts or permit the exclusion or limitation of incidental or consequential damage, so the above limitations may not apply to you. This warranty gives you specific rights, and you may one year from the original date of consumer purchase. This warranty is limited to the repair or replacement of this product only and does not extend to consequential or incidental damage to other products that may be used with this product. This warranty RF warning for Portable device:

Adding Device To Z-Wave Network for QR CODE The device has been evaluated to meet general RF exposure requirement. The device can be Scan here for SmartStar inclusion used in portable exposure condition without restriction. Locally Button Press function:

Note: DSK Code can be found on the packaging box. Parameter Settings also have other rights which vary from state to state. Do not remove or damage them. Notes:

1. Plug the device you want to control into the Z-Wave Smart plug controlled outlet. NOTE: Plug directly into the outlet, do not use with power strip. 1: press 1x: turn output ON or OFF 2: quickly press 3x: inclusion or exclusion 3: quickly press 5x: change Parameter 1 4: quickly press 8x: change Parameter 4 5: quickly press 10x: Reset KWH 6: Factory reset: click Z-Wave button twice quickly, then hold it at least 10 seconds. LED Indicator This parameter can access you to choose the LED indicator to be on when the plug

(light) is on / off, or LED indicator remains on / off all times.

MP21ZP(ZW38SU) Z-Wave Plug With Energy Monitor (800S) i a n h C n i e d a M e s u r o o d n i r o F FCC ID: 2AQURZW38SU-V8 VER: 8.0 Date:

Model: MP21ZP

(ZW38SU) Conforms to UL Std. 60730-1 Cert. to CSA Std. E60730-1 Loading: 15A 1875W RESISTIVE OR GENERAL PURPOSE 10A MAX 1250W TUNGSTEN 1/2 HP I n p u t

1 2 5 V A C 6 0 H z F r e q u e n c y

9 0 8

. 4 2 M H z

NIE-TECH CO., LTD Jinlian commercial center 9001, Jinxiu road No.2, Changan Town, Dongguan City, Guangdong Province, China Federal Communications Commission Authorization and Evaluation Division Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MD 21046 2022-12-29 To whom it may concern:

We, NIE-TECH CO., LTD, hereby certify that the equipment for which authorization is sought (FCC ID:

2AQURZW38SU-V8) is not covered equipment prohibited from receiving an equipment authorization pursuant to 2.903 of the FCC rules. We also certify that, as of the date of the filing of the application, we are not identified on the Covered List (https://www foc. gov/supplychain/coveredlist) as an entity producing covered equipment. By signing this form, we confirm the above and that we are aware of the application requirements listed under 2.914(b) and (4)(5) and (6). The information provided in this letter is based on the referenced rule parts of Title 47 of the CFR as well as KDB 986446 DO1 Sincerely,

[eamb Ate Signature Jiangh Manager NIE-TECH CO., LTD

NIE-TECH CO.,LTD Add: Jinlian commercial center 9001, Jinxiu road No.2, Changan Town, Dongguan City, Guangdong Province, China Date: 2022-12-29 FCC ID: 2AQURZW38SU-V8 Dear Sir/Madam, We, NIE-TECH CO., LTD Hereby declares the following statement for Federal Communications Commission, PCB board, circuit, structure and internal of these model(s) are the same, Only model number is different for these model:

Product name: Z-Wave Mini Smart Plug Model no.: ZW38SU, MP21Z, ZW36SU, MP21ZP Sincerely, front Mes J Name/Title; Jianghai Nie/Manager Company: NIE-TECH CO,, LTD Address: Jinlian commercial center 9001, Jinxiu road No.2, Changan Town, Dongguan City, Guangdong Province, China 13751285558 86 (769) 82286661 nie@nie-tech.com

CONFIDENTIALITY REQUEST for Certification Service in USA Federal Communication Commission Equipment Authorization Division, Application Processing Branch 7435 Oakland Mills Road Columbia, MD 21046 Date:<2022-12-29>

Pursuant to Paragraphs 0.457 and 0.459 of the Commission's Rules (47 C.F.R.) and Section 552(b)(4) of the Freedom of Information Act, we requests confidentiality for the following products:

FCC ID Model name 2AQURZW38SU-V8 ZW38SU For the product stated above, we request that the following information be held confidential;

Exhibits Long-Term Short-Term Short-Term Confidentiality | Confidentiality | Confidentiality Days Extemal Photos ial O Internal Photos D Block Diagram =

Schematics bs) 0 Test Setup Photos im]

User's Manual Parts List ial O Tune Up o Oo Operational Descriptions: x Oo The long-term confidentiality exhibits contain our trade secrets and proprietary information that could be of benefit to our competitors. The short-term confidentiality on the basis of ensuring that business sensitive information remains confidential until the actual marketing of our new device If you have any questions, please feel free to contact me at the address shown below. Sincerely, mnie J Name/Title: _Jianghai Nie/Manager Company: NIE-TECH CO,, LTD Address: Jinlian commercial center 9001, Jinxiu road No.2, Changan Town, Dongguan City, Guangdong Province, China Phone: 13751285558 Fax: 86 (769) 82286661 E-Mail: nie@nie-tech.com

NIE-TECH CO., LTD Jinlian commercial center 9001, Jinxiu road No.2, Changan Town, Dongguan City, Guangdong Province, China Federal Communications Commission Authorization and Evaluation Division Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MD 21046 2022-12-29 To whom it may concern:

We, the undersigned, hereby authorize Eurofins Product Service GmbH to act on our behaffin all matters relating to applications for equipment authorization FCC ID: 2A QURZW38SU-V8 including the signing of all documents related to these matters. Any and all acts carried out by Eurofins Product Service GmbH on our behalf shall have the same effect as acts of our own. By signing this application form, we agree to Eurofins current valid General Terms and Conditions

(AGB),Testing and Certification Regulations (PZO) which can be viewed on following website wwweurofins.de/ee or retrieved on request. We also hereby certify that no party to this application is subject to a denial of benefits, including FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 862 Sincerely,

[re tee Name/Title: Jianghai Nie/Manager Company: NIE-TECH CO,, LTD Address: Jinlian commercial center 9001, Jinxiu road No.2, Changan Town, Dongguan City, Guangdong Province, China Phone: 13751285558 Fax: 86 (769) 82286661 E-Mail: nie@nie-tech.com

{NIE-TECH Co., Ltd}

{ Jinlian commercial center 9001, Jinxiu road No.2, Changan Town,Dongguan City, GuangDongProv., CHINA }

Federal Communications Commission Authorization and Evaluation Division Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MD 21046 U.S. Agent Designation

{2023-12-30}

{ NIE-TECH Co., Ltd} acknowledges their consent for the following contact located in the United States to act as their agent for service of process for the equipment for which authorization is sought (FCC ID: 2AQURZW38SU-

V8):

Name and company of U.S. agent:

{ Jasco Products Company LLC }

Physical U.S. address of agent:

{10 e memorial road Office oklahoma city OK 73114}

FRN of U.S. agent:

{0017309360}

Email address of U.S. agent:

{msimpkins@jascoproducts.com}

{ Jasco Products Company LLC } acknowledges their obligation to accept service of process on behalf of {NIE-

TECH Co., Ltd}.

{ NIE-TECH Co., Ltd} with the FRN [{0027755610}] accepts its obligation to maintain an agent for service of process in the United States for no less than one year after either the grantee has permanently terminated all marketing and importation of the applicable equipment within the U.S., or the conclusion of any Commission-related administrative or judicial proceeding involving the equipment, whichever is later. By signing this form, we confirm the above and that we are aware of the application requirements listed under 2.911(d)(7). The information provided in this letter is based on the referenced rule parts of Title 47 of the CFR as well as KDB 986446 D01. An expiration date for this letter does not exist. In case the U.S. agent changes, the grantee is obligated to notify the FCC within 30 days via the granting TCB. 5 0 V

, U

) 7

) d

1 1 9

. 2 _ t n e g A _ S U

l e d o m

_ 8 4 Sincerely,

Signature

{ jianghai} { Nie }

{ Manager }

{NIE-TECH Co., Ltd}

Signature

{Mark Simpkins}

{Manager}

{Jasco Products Company LLC}