OKIN Refined Electric Technology Co., Ltd Operating Manual of Remote Control system 1 Interface of the remote control 2Button description A. HEAD UP buttonPress and hold the button, the Head actuator will go up. Stop when released. Page 1 of 5 OKIN Refined Electric Technology Co.,Ltd B. HEAD DN buttonPress and hold the button, the Head actuator will go down. Stop when released. C. FOOT UP buttonPress and hold the button, the Foot actuator will go up. Stop when released. D. FOOT DN buttonPress and hold the button, the Foot actuator will go down. Stop when released. E. HEAD & FOOT UP buttonPress and hold the button, the Head and Foot actuator will simultaneously go up. Stop when released. F. HEAD & FOOT DN buttonPress and hold the button, the Head and Foot actuator will simultaneously go down. Stop when released. 3Wireless pairing operation Step1: put in the batteries. Step2: Power on the control box. Step3: Double click the code pairing button on the control box, and then release it, the pairing instruction LED on the control box lights. The control box is in a state to be paired. Step4: Press simultaneously the Head-Up button and the Foot-Up button on the remote control, when the backlight LED on the remote flashes. release these two buttons, if the backlight LED still flashes, it represents that the remote is searching for paired control box. The pairing LED on the control box to be paired is always bright. When the backlight LED on the remote and LED on the control which is to be paired stop flash. The code pairing is finished. To test whether the code pairing is successful, or to test other relevant button of actuator such as the Head-Up
/Down button and the Foot-Up/Down button. If you can hear the tick sound of relay, the code pairing is successful. Otherwise, repeat all the processes above steps. It is strongly recommended that the near control boxes, for example, in a same house, should Page 2 of 5 OKIN Refined Electric Technology Co.,Ltd be configured differently. Each control box must be paired with the different remote control where the DIP-Switch position is deferent. Doesnt pair both control boxes with the same remote control or the different one but in which the DIP-switch position is same. 1. 2. 3. LED 4. LED LED LED LED LED /
DIP DIP 5Connect to the Control Box The control box is designed for using the SMPS of 29VDC/ around 2A as the power. It is Page 3 of 5 OKIN Refined Electric Technology Co.,Ltd necessary to use the SMPS provided by us when normal operation. 29VDC/ 2A In the case of the AC power utility failure, the batteries for backup of 18VDC can be used as the power. It is only for flatting the bed plate without load if the batteries used as the power and each one of the batteries must be new with 9V voltage. You can press and hold the emergency button on the body of the control box to flat the bed. The movement sequence is that the Foot actuator goes down until arrives to the limit the Head one goes down. If release the button, all movement will stop immediately including the massage motors. It isnt also strongly recommended to start the massage motors when the battery box used as power. 18V 9V Page 4 of OKIN Refined Electric Technology Co.,Ltd FCC STATEMENT 1. This device complies with Part 15 of the FCC Rules and Industry Canada licence-exempt RSS standard(s) . Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause undesired operation. 2. Changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/ TV technician for help. INDUSTRY CANADA NOTICE This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. The device can be used in portable exposure conditions without Rf restrictions. Avis dIndustrie Canada Le prsent appareil est conforme aux CNR dIndustrie Canada applicables aux appareils radio exempts de licence. Lexploitation est autorise aux deux conditions suivantes :
(1) lappareil ne doit pas produire de brouillage, et
(2) lutilisateur de lappareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible den compromettre le fonctionnement. Cet appareil numrique ne dpasse pas les Rlements sur linterfrence radio par un appareil numrique de classe B stipules dans les Rglement sur linterfrence redio dindustrie Canada. 2.Les changements ou modifi cations de cette unit non expressment approuvs par la partie responsable de la conformit pourraient annuler lautorit de lutilisateur utiliser lquipement.
Page of