MIX360 QUICK START GUIDE Visit our support site for more detailed instructions, FAQs and videos on using the Mix360. ONvocal.com/support DOWNLOAD For the best Mix360 experience, download the free ONvocal app, available for iPhone and Android. WEAR 1. Place earbuds on magnetic stays at neckband ends. 2. For a more secure fit, bend neckband smaller than your neck size using the Flex Zones before wearing. Bend only in the Flex Zone areas to prevent damage. 3. Put neckband on. One at a time, drape ear bud wires over each ear and squeeze foam tips before inserting, allowing foam to expand for optimal performance and sound isolation. 4. Slide wire cinch up or down to conceal excess wire. 5. Adjust microphone boom so it points toward the corner of your mouth. PAIR 1. Press and hold Power button to turn on the Mix360. The LED flashes red and white to indicate pairing mode is active. 2. Enable pairing on your Bluetooth-enabled device. 3. Select ONvocal from the list of available devices. WIRE CINCH If a PIN is requested, use 0000. CONTROL FLEX ZONE AREA Adjust Music Playback, Volume, Ambient and Voice levels using buttons on the neckband. COMMAND FLEX ZONE AREA FLEX ZONE AREA LED AUDIO UP AUDIO DOWN PLAY/PAUSE POWER VOICE AMBIENT Briefly press Ambient or Voice buttons to enable or disable. Press and hold Ambient or Voice buttons to cycle through volume levels. Press Command button to answer/end calls or activate your phones voice command app. Double press Play/Pause button to skip audio tracks while playing music; single press during a call to mute or un-mute the mic. MAGNETIC STAY LINE INPUT MICRO-USB CHARGING PORT MAGNETIC STAY Use the free ONvocal app for finer adjustments of Audio, Ambient, and Voice levels for music and phone calls alike. Save your favorite settings as presets.
*LED is red while charging and turns white when fully charged. OnVocal-QuickStartGuide-E.6.2.indd 1 1/13/16 3:46 PM All images, copy, specifications, and slogans are the exclusive property of ONvocal, Inc. ONvocal and Mix360 are registered trademarks of ONvocal, Inc. 2016 Hearing Components. Comply is a trademark of Hearing Components. 2016 CSR plc and its group companies. The aptX mark and the aptX logo are trade marks of CSR plc or one of its group companies and may be registered in one or more jurisdictions. iPhone and iPhone 5s are trademarks of Apple Inc., registered in the U.S. and other countries. Made for iPhone means that an electronic accessory has been designed to connect specifically to iPhone and has been certified by the developer to meet Apple performance standards. Apple is not responsible for the operation of this device or its compliance with safety and regulatory standards. Please note that the use of this accessory with iPhone may affect wireless performance. CAUTION: RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE. DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS. FEDERAL COMMUNICATIONS COMMISSION (FCC) STATEMENT 15.21 You are cautioned that changes or modifications not expressly approved by the part responsible for compliance could void the users authority to operate the equipment. 15.105(b) This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instruc-
tions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular in-
stallation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference and (2) this device must accept any interference received, including interference that may cause undesired operation of the device. For body worn operation, this device has been tested and meets FCC RF exposure guidelines when used with an accessory that contains no FCC RF RADIATION EXPOSURE STATEMENT metal and that positions the device a minimum of 5mm from the body. Use of other accessories may not ensure compliance with FCC RF exposure guidelines. To comply with the FCC RF exposure compliance requirements, this device and its antenna must not be co-located or operating in conjunction with any other antenna or transmitter. CANADA, INDUSTRY CANADA (IC) This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le prsent appareil est conforme aux CNR dIndustrie Canada applicables aux appareils radio exempts de licence.Lexploitation est au-
toriseauxdeuxconditionssuivantes: (1)lappareilne doitpasproduiredebrouillage,et (2)lutilisateurdelappareildoitacceptertoutbrouil-
lage radiolectriquesubi,mmesile brouillageestsusceptibledencompromettrelefonctionnement. Pour se conformer aux exigences de conformit RF canadienne lexposition, cet appareil et son antenne ne doivent pas tre co-localiss ou fonctionnant en conjonction avec une autre antenne ou transmetteur. DCLARATION DE LEXPOSITION AUX RADIATIONS RF 2016 ONvocal, Inc. www.ONvocal.com OnVocal-QuickStartGuide-E.6.2.indd 2 1/13/16 3:46 PM START MIXING