4) Device Dimensions Maintenance and Usage FCC Compliance Statement Increase the separation between the equipment and 88.00 25.90 5 1) If any cables become damaged, seek a replacement. 2) Do not insert unknown materials into any port on the CM20, this may cause serious damage to the device. If repairs are required, please contact a professional technician instead of attempting them on your own. Make sure the various cables connect to provide the appropriate voltages at the proper pins. For best performance, the antennas should be placed in an elevated area and kept free from obstructions. 3) 4) 5) This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
This device may not cause harmful interference, and This device must accept any interference received, including interference that may cause undesired operation. WARNING This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:
Reorient or relocate the receiving antenna. installed and used to radio or interference if not receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. CAUTION Any changes or modifications not expressly approved by the manufacturer could void the user's authority to operate this equipment. RADIATION EXPOSURE This device complies with FCC radiation exposure limits for general environments. do not throw away, requires professional recycling Index of Icons 7 Class II equipment for indoor use only VI energy efficiency marking (level VI)
~ AC voltage DC voltage 0 2 6 9
. Figure 6: device dimensions (mm) Instructions 1) Switching the device on and off Switch on:
Link the CM20 to a power source via the DC power jack or USB Type B port. Switch off:
Disconnect the CM30 from the power terminal it is connected to. 2) Environmental Conditions Storage Temperature:
Working Temperature:
Relative Humidity:
-30C
-30C 5%
70C (-22F 70C (-22F 158F) 158F)
95% (no condensation)
CM20 COMMUNICATION MODULE Contents The following items may be included with your CM20 unit, contents may vary based on specific product configuration. Name Quantity CM20 communication module USB A to B cable Wi-Fi antenna (optional) 2G/3G/4G antenna (optional) power adapter Product Description 1 1 1 1 1 Digital I/O USB Type A port RJ45 port (RS232) Ethernet port LED status indicators 3) Device Connection P/N: 200312000000454 Installation 1) SIM Card Insertion Wi-Fi antenna port 2G/3G/4G antenna port SIM card slot reset button USB Type B port DC power jack Figure 2: front view (right side) top bottom left front right back SIM card slot push button Figure 4: SIM card slot (CM20 right side) On the right side of the CM20, there is a mini-SIM sized SIM card slot. To install a SIM card, first open the mount by fully depressing the yellow button next to the card slot and inserting a card into the mount. Push the mount back into place to secure the card, and then restart the device to detect it. 2) Antenna is used The CM20 comes packaged with two antennas, one antenna for communicating with Wi-Fi networks, and another is for communicating with 2G, 3G, or 4G networks. These antennas can be attached to the CM20 at the two SMA connectors indicated in Figure 2. Figure 5: connecting the CM20 to the IM20 The CM20 is designed to function as a communications module for other PAX devices. It can connect to devices such as the IM20 POS terminal through its USB port to provide additional functionality. As shown in Figure 5, the USB Type A port of the CM20 can be connected to the USB Type B port of the IM20, both powering the IM20 and allowing for communications between the two devices. This device can provide similar functionality to other POS terminals such as the IM500 and IM700. Contact your dealer for any questions regarding the compatibility and connection of specific PAX devices. PAX TECHNOLOGY LIMITED reserves the right to change product specifications without prior notification. Manufacturer: PAX Computer Technology (Shenzhen) Co., Ltd. Address: 4FL, Building #3, Software Park, 2nd Central Science-Tech RD, High-Tech Industrial Park, Shenzhen, Guangdong, PRC Tel: 0755-86169630 Fax: 0755-86169634 Website: http://www.pax.com.cn Figure 1: front view (left side) Figure 3: view from all sides 1. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference.
(2) This device must accept any interference received, including interference that may cause undesired operation. 2. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate FCC Statement the equipment. NOTE:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. Body-worn Operation This device was tested for typical body-worn operations. To comply with RF exposure requirements, a minimum separation distance of 20 cm must be maintained between the users body and the handset, including the antenna. Third-party belt-clips, holsters, and similar accessories used by this device should not contain any metallic components. Body-worn accessories that do not meet these requirements may not comply with RF exposure requirements and should be avoided. Use only the supplied or an approved antenna. IC STATEMENT Thisdevicecontainslicenceexempttransmitter(s)/receiver(s)thatcomplywithInnovation,Science andEconomicDevelopmentCanadaslicenceexemptRSS(s).Operationissubject tothefollowingtwoconditions:
(1)Thisdevicemaynotcauseinterference.
(2)Thisdevicemustacceptanyinterference,includinginterferencethatmaycauseundesiredoperationofthedevice This device was tested for typical body-worn operations. To comply with RF exposurerequirements, a minimum separation distance of 20 cm must be maintained between the users body and the handset, including the antenna. Third-party belt-clips, holsters, and similar accessories used by this device should not contain any metallic components. Body-worn accessories that do not meet these requirements may not comply with RF exposure requirements and should be avoided. Use only the supplied or an approved antenna. Le prsent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. Cetappareilcontientdesmetteurs/rcepteursexemptsdelicenceconformesauxRSS(RSS) d'Innovation,SciencesetDveloppementconomiqueCanada.Lefonctionnementestsoumisaux deuxconditionssuivantes:
(1)Cetappareilnedoitpascauserd'interfrences.
(2)Cetappareildoitacceptertouteslesinterfrences,ycompriscellessusceptiblesde provoquerunfonctionnementindsirabledel'appareil. Cet appareil a t test pour des oprations ports sur le corps typiques. Pour se conformer aux exigences d'exposition aux radiofrquences, une distance minimale de 20 cm doit tre maintenue entre le corps de l'utilisateur et le combin, y compris l'antenne. Les pinces de ceinture, les tuis et autres accessoires similaires utiliss par cet appareil ne doivent pas contenir de composants mtalliques. Les accessoires portatifs qui ne rpondent pas ces exigences peuvent ne pas se conformer aux exigences d'exposition RF et doit tre vite. Utilisez uniquement l'antenne fournie ou une antenne approuve