E600 Integrated Smart Terminal 1.Contents Checklist Please check the components after unpacking. If any one of them is missing, or if there is a page missing from the product manual,ect.,please contact the dealer. Name E600 AC Power Adapter AC Power Cable Product manual 2, Product Description Qty. 1 1 1 1 3. Installation Power on: Press and hold the Power button for three seconds until the main screen displays normally. Power off: Press and hold the Power button for three seconds until the shutdown menu appears, tap Shutdown, and then shutting... appears. The terminal will be turned off after a few seconds. Swipe the magnetic stripe card: Place the magnetic stripe face down (keep the magnetic stripe card perpendicular to the main display), swipe card through the magnetic card slot at a constant speed. IC Card: Place the IC chip face down, then insert the IC card into the card slot, and push it to the end. Contactless card: Put the contactless card on the center of the payment module screen. Tear paper: Press the print paper downward along the cutter and tear it leftward or rightward when getting close to the main display. Charge: Insert the external adapter or the base to charge the device, the indicator lighting in red means the device is charging; the indicator lighting in green means charging is completed; the indicator flashing in red and green alternately meanscharging is abnormal. Replace SIM card: Open the battery cover on the bottom of the machine,remove the battery, and follow the prompt to insert/take out the SIM card. Replace SD card:Open the battery cover on the bottom of the machine, remove the battery, and follow the prompt to insert/take out the SD card. 4, Specification Operating System: Android 7.1 CPU: Cortex A53Qaud-core, 1.4GHz Memory: 1GB RAM + 8GB Flash Memory Display: 8" inch, resolution:800*1280, multi-touch capacitive touch screen Printer: 2" high-speed thermal printer, support 58*50mm print paper roll Audio: Built-in speaker, support headphone output Camera: Front camera, 5 mega-pixel, fixed-focus, high-speed code scanning Rear camera,30W-pixel,fixed-focus, high-speed code scanning L-Sensor (Ambient Light Sensor): Automatically adjust the backlight brightness of the main display Wireless Communication: Support WIFI, Bluetooth, 3G/4G Positioning: Support GPS, Compass, Gingileo, GLONASS Card Slots: SIM card slot Micro SD card slotmaximum supports 128GB magnetic stripe card/IC card slot, using two-in-onesupport MAG&ICC Magnetic Card Reader: Support track 1/2/3. IC Card Reader: Conform to the standard of ISO7816, EMV2000 L1&L2, PBOC3.0 Contactless Card Reader: Compatible with ISO14443 Type A&B Working Environment Temperature: 050(32122) R.H.: 10%93%( non-condense) Storage Environment Temperature:-2070(-4158) R.H.:595 (non-condense) 5. Cautions of installation and usage 1Avoid exposing the terminal in hot, humid,dusty or strong electromagnetic environment. 2Do not violently vibrate, shake or beat the product. 3Do not plug/unplug any units of the product when it is power on, otherwise it may damage the internal circuit. 4Do not maintain the terminal if you are non-professional 5Before inserting the magnetic stripe/IC/contactless card, please check whether there is any foreign object inside or surround the card slot , and if any , report to related personnel. Risk of explosion if battery replaced by an incorrect type. Dispose of used batteries according to the instructions. Hereby, PAX Computer Technology (Shenzhen) Co., Ltd. declares that the radio equipment type E600 is in compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity is available at the following internet address http://www.pax.com.cn/ProductCE.aspx Caution Icon shows Do not throw away, need professional recycling. Class II Equipment For indoor use only Energy Efficiency Marking AC voltage DC voltage The MAINS plug is used as the disconnected device. FCC Regulations:
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This device has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiated radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help. Caution: Changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. FCC RF Exposure Information (SAR) This device is designed and manufactured not to exceed the emission limits for exposure to radio frequency (RF) energy set by the Federal Communications Commission of the United States. During SAR testing, this device is set to transmit at its highest certified power level in all tested frequency bands, and placed in positions that simulate RF exposure in usage near the body. Although the SAR is determined at the highest certified power level, the actual SAR level of the while operating can be well below the maximum value. This is because the device is designed to operate at multiple power levels so as to use only the power required to reach the network. In general, the closer you are to a wireless base station antenna, the lower the power output. The exposure standard for wireless employs a unit of measurement known as the Specific Absorption Rate, or SAR. The SAR limit set by the FCC is 1.6W/kg. The FCC has granted an Equipment Authorization for this model device with all reported SAR levels evaluated as in compliance with the FCC RF exposure guidelines. SAR information on this model device is on file with the FCC and can be found under the Display Grant section of www.fcc.gov/oet/ea/fccid after searching on FCC ID: V5PE600 For this device, the highest reported SAR value for usage near the body is 1.21 W/kg. While there may be differences between the SAR levels of various devices and at various positions, they all meet the government requirement. ISED Notice prsentappareilestconforme This device complies with Innovation, Science and Economic Development Canada license-exempt RSS standard(s). Operation is subject to the following two conditions:
(1) this device may not cause interference, and
(2) this device must accept any interference, including interference that may cause undesired operation of the device. Le et Dveloppementconomique Canada applicables aux appareils radio exempts de licence. L'exploitationestautorise aux deux conditions suivantes:
(1) l'appareil ne doit pas produire de brouillage, et
(2) l'utilisateur de l'appareildoit accepter tout brouillageradiolectriquesubi, mmesi le brouillageest susceptible d'en IC: 11689A-E600 Innovation, Sciences CNR aux ISED Radiation Exposure Statement This EUT is in compliance with SAR for general population/uncontrolled exposure limits in ISED RSS-102 and had been tested in accordance with the measurement methods and procedures specified in IEEE 1528 and IEC 62209. This device and its antenna(s) must incontrle IEEE 1528 et limitesd'exposition DAS pour linnovation et aux la norme CNR-102 science de not be co-located or operating in conjunction with any other antenna or transmitter. la Cetappareilestconforme le populationgnrale de dveloppementconomique Canadaet a ttestenconformit avecles mthodes de mesure et procduresspcifiesdans IEC 62209.Cetappareil et saousesantennes ne doivent pas treco-localissoufonctionnerenconjonction avec tout autreantenneoutransmetteur. the device for operation in the band 51505250 MHz is only for indoor use to reduce the potential for harmful interference to co-channel mobile satellite systems Le dispositif a tutilis pour la construction de la bande 5150 5250 MHz pour la consommation de matriel pour rduire le potentiel pour les systmes de tlvision mobiles PAX TECHNOLOGY LIMITED reserves the right to change product technology specifications without notifying. PAX TECHNOLOGY LIMITED Manufacturer: PAX Computer Technology (Shenzhen) Co.,Ltd. Address:4/F, No.3 Building, Software Park, Second Central Science-Tech Road, High-Tech Industrial Park, Shenzhen, Guangdong, P.R.C. Tel: 0755-86169630 Website: http://www.pax.com.cn Responsible Party: PAX Technology, Inc. 8880 Freedom Crossing Trail, Building 400, 3rd Floor Suite 300, Jacksonville , Florida, 32256 Nikolai Francis T: (904) 217-6387 Fax: 0755-86169634