Installation Manual D190 Mobile payment terminal PAX TECHNOLOGY LIMITED PAX TECHNOLOGY LIMITED 1. Contents Checklist Please check the components after unpacking. If any one of them is missing, or if there is a page missing from the product manual, etc. Please use original accessories including power adapter, USB cable and battery, please contact the dealer if you need to change any accessories. Name D190 Mobile payment terminal AC Power Adapter USB Cable Battery Product Manual 2. Installation SAM/SIM Card 1) Remove the battery cover. 2) Remove the battery. Qty. 1 1 1 1 1 3) Insert the SAM/SIM card to the corresponding card slot (PS: The default hardware configuration only support SIM1 slot). Battery:
Alignment battery tip side to battery tip in terminal and insert. 3. Instructions 1) Power ON/OFF Power on: Plug in power adapter or insert the battery, Press until the PAX LOGO display on LCD. button for 3 seconds button for 3 seconds until the Power off display on the Power off: Press LCD ,then press ENTER, then the POS terminal is being turned off. IC Card Put IC card chip side upward, push-in IC card slot and to bottom. 2) 3) Contactless Card The card read area is above the LCD, Put the card above the LCD. 4) Battery Charge display Connecting USB port with external adapter can charge the battery. And there are charging display. 5) Battery Charge style Please use the original adapter, if you need to charge. Working Environment Temperature: 050(32122) Humidity: 10%93%( non-condense) Storage Environment Temperature:-2070(-4158) Humidity.:5%95% (non-condense) 4. Installation and Usage Tips 1) Avoid putting the terminal in direct sunlight, high temperature, moist, or dusty environment. 2) Forbid non-professional to repair the terminal. 3) Before insert the card, please check internal and around of IC card slot. if you found some suspicious objects , must report to related administrator. 5. Lithium Ion Battery Usage Tips WARNING:
1Don't use the battery in sunlight or smoke, dust environment. 2Prohibited to strike, squeeze and tread on battery or throw it into the liquid and fire. 3If battery is impressive, deformed, damaged or exothermic seriously, please stop using immediately and replace it!
4If the continuous working time is only half of new one, the battery life may be end. Please replace it!
5Must use the specified battery model and charger, otherwise there will be explosion 6Charging time can not exceed 24 hours. If the battery is out of power, please recharge in time. Avoid damaging the battery in over-charge and over-discharge. 7If be non-use for long time, please recharge the battery per 6 months to avoid shortening its life. 8Suggest to replace it when the battery have been used for 2 years. 9Be sure to follow the instructions to dispose the wasted batteries. 6. Icon shows Do not throw away, need professional recycling. Class II Equipment For indoor use only Energy Efficiency Marking AC voltage DC voltage The full text of the EU declaration of conformity is available at the following internet address https://www.pax.com.cn/ProductCE/index.aspx FCC compliance statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
-- Reorient or relocate the receiving antenna.
-- Increase the separation between the equipment and receiver.
-- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-- Consult the dealer or an experienced radio/TV technician for help. FCC SAR statement This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. End user must follow the specific operating instructions for satisfying RF exposure compliance. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. The portable device is designed to meet the requirements for exposure to radio waves established by the Federal Communications Commission (USA). These requirements set a SAR limit of 1.6 W/kg averaged over one gram of tissue. The highest SAR value reported under this standard during product certification for use when properly worn on the body The portable device is designed to meet the requirements for exposure to radio waves established by the Federal Communications Commission (USA). These requirements set a SAR limit of 4 W/kg averaged over ten gram of tissue. The highest SAR value reported under this standard during product certification for use when properly worn on the extremity. ISED compliance statement This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canadas licence-exempt RSS(s). Operation is subject to the following two conditions:
(1) This device may not cause interference.
(2) This device must accept any interference, including interference that may cause undesired operation of the device. Lmetteur/rcepteur exempt de licence contenu dans le prsent appareil est conforme aux CNR dInnovation, Sciences et Dveloppement conomique Canada applicables aux appareils radio exempts de licence. Lexploitation est autorise aux deux conditions suivantes :
(1) Lappareil ne doit pas produire de brouillage;
(2) Lappareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible den compromettre le fonctionnement. The device for operation in the band 51505250 MHz is only for indoor use to reduce the potential for harmful interference to co-channel mobile satellite systems;
le dispositif utilis dans la bande 5150-5250 MHz est rserv une utilisation en intrieur afin de rduire le risque de brouillage prjudiciable aux systmes mobiles par satellite dans le mme canal;
IC SAR statement This equipment complies with ISED radiation exposure limits set forth for an uncontrolled environment. End user must follow the specific operating instructions for satisfying RF exposure compliance. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. The portable device is designed to meet the requirements for exposure to radio waves established by the ISED. These requirements set a SAR limit of 1.6 W/kg averaged over one gram of tissue. The highest SAR value reported under this standard during product certification for use when properly worn on the body. The portable device is designed to meet the requirements for exposure to radio waves established by the ISED. These requirements set a SAR limit of 4W/kg averaged over ten gram of tissue. The highest SAR value reported under this standard during product certification for use when properly worn on the extremity. Cet quipement est conforme aux limites dexposition aux rayonnements ISED tablies pour un environnement non contrl. Lutilisateur final doit suivre les instructions spcifiques pour satisfaire les normes. Cet metteur ne doit pas tre co-implant ou fonctionner en conjonction avec toute autre antenne ou transmetteur. Le dispositif portatif est conu pour rpondre aux exigences dexposition aux ondes radio tablie par le dveloppement nergtique DURABLE. Ces exigences un SAR limite de 1,6 W/kg en moyenne pour un gramme de tissu. La valeur SAR la plus leve signale en vertu de cette norme lors de la certification de produit utiliser lorsquil est correctement port sur le corps. La conception de l'quipement portatif doit satisfaire aux exigences d'exposition aux ondes radio spcifies par l'ised. Ces exigences limitent le DAS moyen de 10 g de tissu 4 W / kg. La valeur SAR la plus leve rapporte conformment la prsente norme, lorsqu'elle est correctement porte sur les membres pendant la certification du produit. P/N: 200312000000360 PAX TECHNOLOGY LIMITED reserves the right to change product technology specifications without notifying. PAX TECHNOLOGY LIMITED Manufacturer: PAX Computer Technology (Shenzhen) Co.,Ltd. Address: 4/F, No.3 Building, Software Park, Second Central Science-Tech Road, High-Tech Industrial Park, Shenzhen, Guangdong, P.R.C. Tel: 0755-86169630 Website: http://www.pax.com.cn Fax: 0755-86169634