FCC ID: V5PS9204GBW Mobile Payment Terminal

S920 Mobile Payment Terminal PAX TECHNOLOGY LIMITED 1. Appearance Description 2. installation SAM/SIM/SD Card a) Use a coin or screwdriver to remove the battery cover (At the bottom of the terminal). b) Insert the SAM/SIM/SD card to the corresponding card slot. Battery replacement:

a) Use a coin or screwdriver to remove the battery cover (At the bottom of the terminal). b) Remove the old battery: hold the battery, and pull it out. c) Replace with a new battery: hold the battery connector and insert it into the power socket, then align the battery in the battery compartments 3. Instructions 1Power ON/OFF terminal turns on successfully. turns off successfully. 2Magnetic Stripe Card Power onPress the ON/OFF button two seconds until LCD backlight light, the Power offPress the ON/OFF button two seconds until LCD no display, the terminal Put magnetic stripe side of magnetic card towards device interior, swipe the card with a steady speed during through magnetic reader slot.

(Support bi-directional swiping) 3IC Card Put IC card chip side upward, push-in IC card slot and to bottom. 4Contactless Card Put the contactless card into the sensing area above the LCD 5Shred paper operating Instructions Make paper 45 degrees angle right to paper knife and shred paper. 4. Specifications Default CPU 32-bitARM11 Memory128MB DDR RAM , 256MB NAND Flash Display3.5 -inch 240x320 pixel color TFT LCDLED backlightTouch Screen Keypad10 alphanumeric keys, 5 functional keys Magnetic Card Reader Track 1/2/3bi-directional swipe IC Card Reader1 user card EMV2000 SAM slots2 SAM slots(ISO7816) Communication LTE GSM Peripheral Ports: 1 MicroUSB Printer : Thermal printer; Speed:20 lines/sec; Paper width:58mm Paper roll outside diameter:25mm Power Supply Input: 100240VAC50Hz/60Hz0.2A Max Output: 5.0VDC1A BatteryLi-ion bttery, 3350mAh, 3.6V Working Environment Temperature0 ~50(32~120) R.H.: 10%~93%(non-condense) Storage Environment Temperature:-20 ~ 70 (-4~150) R.H.:5% ~95%(non-condense) Dimensions165mm Weight330g 78mm 61mmL W H Optional: WiFi, BT, Single SIM slots Built-in contactless card reader moduleISO/IEC 14443 Type A/B, Mifare

/Felica, card sensing area: LCD screen) 5. Installation and Usage Tips 1Avoid putting the terminal in direct sunlight, high temperature, moist, or dusty environment. 2Forbid non-professional to repair the terminal. 3Before insert the card, please check internal and around of IC card slot. when you found some suspicious objects , must report to related administrator. 6. Lithium Ion Battery Usage Tips 1) Charge indoor by PAX charger, where is cool and well ventilated;

2) Do not apart the battery;

3) Do not short circuit the battery;

4) Keep the battery away from sunshine, smog and dust;

5) Do not squeeze, punch the battery, put it into liquid or near fire;

6) Keep way from environment which is too hot , too cold, damp and highly explosive;

7) Once a failure happens such as heating or distortion, or it was broken down. Please change new battery;

8) Change new battery if it cannot satisfy your requirement;

9) Change new battery if using more than two years. Risk of explosion if the battery is replaced by an incorrect type or equivalent text. FCC Regulations:

This device complies with part 15 of theFCC Rules. Operation is subject to the following two conditions: (1) This device maynot cause harmful interference, and (2) thisdevice must accept any interference received, including interference that maycause undesired operation. This device has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiated radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

-Reorient or relocate the receiving antenna.

-Increase the separation between the equipment and receiver.

-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

-Consult the dealer or an experienced radio/TV technician for help. Caution: Changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. FCC RF Exposure Information (SAR) This device is designed and manufactured not to exceed the emission limits for exposure to radio frequency (RF) energy set by the Federal Communications Commission of the United States. During SAR testing, this device is set to transmit at its highest certified power level in all tested frequency bands, and placed in positions that simulate RF exposure in usage near the body. Although the SAR is determined at the highest certified power level, the actual SAR level of the while operating can be well below the maximum value. This is because the device is designed to operate at multiple power levels so as to use only the power required to reach the network. In general, the closer you are to a wireless base station antenna, the lower the power output. The exposure standard for wireless employs a unit of measurement known as the Specific Absorption Rate, or SAR. The SAR limit set by the FCC is 1.6W/kg. The FCC has granted an Equipment Authorization for this model device with all reported SAR levels evaluated as in compliance with the FCC RF exposure guidelines. SAR information on this model device is on file with the FCC and can be found under the Display Grant section of www.fcc.gov/oet/ea/fccid after searching on FCC ID: V5PS9204GBW For this device, the highest reported SAR value for near the body is 2.98W/kg for FCC/ IC. The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction. While there may be differences between the SAR levels of various devices and at various positions, they all meet the government requirement. Industry Canada statement This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions:

1) 2) this device may not cause interference, and this device must accept any interference, including interference that may cause undesired operation of the device. Le prsent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorise aux deux conditions suivantes:

1) 2) l'appareil ne doit pas produire de brouillage, et l'utilisateur de l'appareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible d'en compromettre le fonctionnement. This device and its antenna(s) must not be co-located or operating in conjunction with any other antenna or transmitter, except tested built-in radios. Cet appareil et son antenne ne doivent pas tre situs ou fonctionner en conjonction avec une autre antenne ou un autre metteur, exception faites des radios intgres qui ont t testes. The County Code Selection feature is disabled for products marketed in the US/ Canada. La fonction de slection de l'indicatif du pays est dsactive pour les produits commercialiss aux tats-Unis et au Canada. Radiation Exposure Statement:

This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 0cm between the radiator & your body. Dclaration d'exposition aux radiations:

Cet quipement est conforme aux limites d'exposition aux rayonnements IC tablies pour un environnement non contrl. Cet quipement doit tre install et utilis avec un minimum de 0 cm de distance entre la source de rayonnement et votre corps.

a) b) c) d) e) f) g) SGS North America Inc. 620 Old Peachtree Road SUITE 100 Suwanee, Georgia 30024 United States Applicant Declaration Applicant Legal Business Name PAX Technology Limited Room 2416, 24/F., Sun Hung Kai Centre, 30 Harbour, Hong Kong, China Address Grantee Code FCC ID Contact Email Contact Phone Authorized Contact Name Jenna Tan V5P V5PS9204GBW certservice@paxsz.com 86-755-86156663 I, the undersigned, certify that I am an authorized signatory for the Applicant and therefore declare;

in accordance with 47CFR2.911(d), all of the statements herein and the exhibits attached hereto are true and correct to the best of my knowledge and belief. in accepting a Grant of Equipment Authorization issued by a TCB, under the authority of the FCC, as a result of the representations made in this application, the Applicant is responsible for:

labeling the equipment with the exact FCC ID as specified in this application,

(1)

(2) compliance statement labeling pursuant to the applicable rules,

(3) compliance of the equipment with the applicable technical rules, if the Applicant is not the actual manufacturer of the equipment, appropriate arrangements have been made with the manufacturer to ensure that production units of this equipment will continue to comply with the FCCs technical requirements. in accordance with 47 CFR 2.909 and KDB394321, the Applicant has read, understood and agrees to accept that they are the responsible party and agree to abide by their responsibilities as specified under 47 CFR 2.909 and KDB394321. in accordance with ISO17065, FCC KDB641163, FCC KDB610077, KDB394321 and RSP-100, the Applicant has read, understood, accepts and agrees to abide by the post market surveillance requirements.

(1)

(2)

(3) the Applicant understands, accepts and agrees that a sample may be requested for surveillance testing. the Applicant shall make provisions to always have a production sample available upon request by SGS, FCC and/or ISED. the Applicant shall, upon request by SGS, at the Applicants expense, provide a production sample of the requested product to SGS, FCC and/or ISED as instructed. The sample shall include all support devices, cables, software, accessories or other hardware or software required for evaluation, review, certification and audit surveillance of products certified by SGS. neither the Applicant nor any party to the application is subject to a denial of Federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 862 because of a conviction for possession or distribution of a controlled substance. See 47CFR 1.2002(b) for the definition of a party for these purposes. the Applicant has read, understood, accepts and agrees to abide by the SGS North America, Inc.(TCB) terms and conditions. Link to CFRs: https://www.fcc.gov/wireless/bureau-divisions/technologies-systems-and-innovation-division/rules-regulations-title-47 Link to KDBs: https://apps.fcc.gov/oetcf/kdb/index.cfm Link to RSP-100: https://www.ic.gc.ca/eic/site/smt-gst.nsf/eng/sf01130.html Applicant Signature:

Date:

November 14, 2020 Print Name:

Title:

*NOTE: This declaration cannot be signed by an Agent, it shall be signed by an authorized person listed in the FCC database Jenna Tan Certification supervisor Applicant Declaration Rev:0.0

PAX Technology Limited We, PAX Technology Limited declare that this EUT (FCC ID: V5PS9204GBW) doesnt have ad Hoc Mode function on non-US/Canada frequencies. In addition, the frequency selection feature is disabled by firmware for devices marketed to the US/ Canada. For DTS part of this device, only channels 1-11 will be used in North America. Country code selection is disabled. Should you have any questions or comments regarding this matter, Please have my best attention. Sincerely yours, Print Name: Jenna Tan Title: Certification supervisor Signature:

On behalf of Company: PAX Technology Limited Telephone: 86-755-86156663 E-mail: certservice@paxsz.com

PAX Technology Limited Date: 2020-11-14 TO:

Federal Communication Commission Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MID 21046 Regarding: FCC ID: V5PS9204GBW To whom it may concern:

We, the undersigned, hereby authorize SGS-CSTC Standards Technical Services Co., Ltd. (SGS) Shenzhen Branch and Keny Xu in SGS-CSTC Standards Technical Services Co., Ltd. (SGS) Shenzhen Branch to act on our behalf in all manners relating to application for equipment authorization with respect to the FCC ID above, including signing of all documents relating to these matters. Any and all acts carried out by the agent on our behalf shall have the same effect as acts of our own. We, the undersigned, hereby certify that we are not subject to a denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 853(a). Where our agent signs the application for certification on our behalf, I acknowledge that all responsibility for complying with the terms and conditions for Certification, as specified by SGS North America, Inc., still resides with PAX Technology Limited. This authorization is valid until further written notice from the applicant. Print Name: Jenna Tan Title: Certification supervisor Signature:

On behalf of Company: PAX Technology Limited Telephone: 86-755-86156663 E-mail: certservice@paxsz.com

PAX Technology Limited TO:

Federal Communication Commission Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MID 21046 Confidentiality Request regarding application for FCC ID: V5PS9204GBW Regarding:

LONG TERM CONFIDENTIALITY Pursuant to 47 CFR Section 0.459 and 0.457 of the commissions rules, the applicant hereby request confidential treatment of the documents listed below, associated with the certification application referenced above. Schematic(s) Block Diagrams Operational Descriptions BOM List Tune Up Procedure The documents above contain proprietary information not released to the public. Public disclosure of this information may prove harmful to the business of the applicant. SHORT TERM CONFIDENTIALITY Additionally, the applicant requests the following documents be held confidential until the device is marketed or 45 days from the grant date, whichever is less. If the device is marketed within 45 days of the Grant Date, the applicant will notify the TCB per FCC KDB 726920 D01 Confidentiality Request Procedures. External Photos Internal Photos Test Setup Photos User manual(s) Sincerely, Print Name: Jenna Tan Title: Certification supervisor Signature:

On behalf of Company: PAX Technology Limited Telephone: 86-755-86156663 E-mail: certservice@paxsz.com