S920 Mobile Payment Terminal PAX TECHNOLOGY LIMITED 1. Appearance Description 2. installation SAM/SIM/SD Card a) Use a coin or screwdriver to remove the battery cover (At the bottom of the terminal). b) Insert the SAM/SIM/SD card to the corresponding card slot. Battery replacement:
a) Use a coin or screwdriver to remove the battery cover (At the bottom of the terminal). b) Remove the old battery: hold the battery, and pull it out. c) Replace with a new battery: hold the battery connector and insert it into the power socket, then align the battery in the battery compartments 3. Instructions 1Power ON/OFF Power onPress the ON/OFF button two seconds until LCD backlight light, the terminal turns on successfully. Power offPress the ON/OFF button two seconds until LCD no display, the terminal turns off successfully. 2Magnetic Stripe Card Put magnetic stripe side of magnetic card towards device interior, swipe the card with a steady speed during through magnetic reader slot.
(Support bi-directional swiping) 3IC Card Put IC card chip side upward, push-in IC card slot and to bottom. 4Contactless Card Put the contactless card into the sensing area above the LCD 5Shred paper operating Instructions Make paper 45 degrees angle right to paper knife and shred paper. 4. Specifications Default CPU 32-bitARM11 Memory128MB DDR RAM , 256MB NAND Flash Display3.5 -inch 240x320 pixel color TFT LCDLED backlightTouch Screen Keypad10 alphanumeric keys, 5 functional keys Magnetic Card Reader Track 1/2/3bi-directional swipe IC Card Reader1 user card EMV2000 SAM slots2 SAM slots(ISO7816) Communication LTE Peripheral Ports: 1 MicroUSB Printer : Thermal printer; Speed:20 lines/sec; Paper width:58mm Paper roll outside diameter:25mm Power Supply Input: 100240VAC50Hz/60Hz0.2A Max Output: 5.0VDC1A BatteryLi-ion bttery, 3350mAh, 3.6V Working Environment Temperature0 ~50(32~120) R.H.: 10%~93%(non-condense) Storage Environment Temperature:-20 ~ 70 (-4~150) R.H.:5% ~95%(non-condense) Dimensions165mm Weight365g 78mm 61mmL W H Optional: WiFi, BT, Single SIM slots Built-in contactless card reader moduleISO/IEC 14443 Type A/B, Mifare
/Felica, card sensing area: LCD screen) 5. Installation and Usage Tips 1Avoid putting the terminal in direct sunlight, high temperature, moist, or dusty environment. 2Forbid non-professional to repair the terminal. 3Before insert the card, please check internal and around of IC card slot. when you found some suspicious objects , must report to related administrator. 6. Lithium Ion Battery Usage Tips 1) Charge indoor by PAX charger, where is cool and well ventilated;
2) Do not apart the battery;
3) Do not short circuit the battery;
4) Keep the battery away from sunshine, smog and dust;
5) Do not squeeze, punch the battery, put it into liquid or near fire;
6) Keep way from environment which is too hot , too cold, damp and highly explosive;
7) Once a failure happens such as heating or distortion, or it was broken down. Please change new battery;
8) Change new battery if it cannot satisfy your requirement;
9) Change new battery if using more than two years. FCC Regulations:
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This device has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiated radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help. Caution: Changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. FCC RF Exposure Information (SAR) This device is designed and manufactured not to exceed the emission limits for exposure to radio frequency (RF) energy set by the Federal Communications Commission of the United States. During SAR testing, this device is set to transmit at its highest certified power level in all tested frequency bands, and placed in positions that simulate RF exposure in usage near the body. Although the SAR is determined at the highest certified power level, the actual SAR level of the while operating can be well below the maximum value. This is because the device is designed to operate at multiple power levels so as to use only the power required to reach the network. In general, the closer you are to a wireless base station antenna, the lower the power output. The exposure standard for wireless employs a unit of measurement known as the Specific Absorption Rate, or SAR. The SAR limit set by the FCC is 1.6W/kg. The FCC has granted an Equipment Authorization for this model device with all reported SAR levels evaluated as in compliance with the FCC RF exposure guidelines. SAR information on this model device is on file with the FCC and can be found under the Display Grant section of www.fcc.gov/oet/ea/fccid after searching on FCC ID: V5PS920LTE For this device, the highest reported SAR value for near the body is 0.84W/kg. While there may be differences between the SAR levels of various devices and at various positions, they all meet the government requirement. Industry Canada statement This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions:
1) 2) this device may not cause interference, and this device must accept any interference, including interference that may cause undesired operation of the device. Le prsent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorise aux deux conditions suivantes:
1) 2) l'appareil ne doit pas produire de brouillage, et l'utilisateur de l'appareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible d'en compromettre le fonctionnement. This device and its antenna(s) must not be co-located or operating in conjunction with any other antenna or transmitter, except tested built-in radios. Cet appareil et son antenne ne doivent pas tre situs ou fonctionner en conjonction avec une autre antenne ou un autre metteur, exception faites des radios intgres qui ont t testes. The County Code Selection feature is disabled for products marketed in the US/ Canada. La fonction de slection de l'indicatif du pays est dsactive pour les produits commercialiss aux tats-Unis et au Canada. Radiation Exposure Statement:
The product comply with the Canada portable RF exposure limit set forth for an uncontrolled environment and are safe for intended operation as described in this manual. The further RF exposure reduction can be achieved if the product can be kept as far as possible from the user body or set the device to lower output power if such function is available. Dclaration d'exposition aux radiations:
Le produit est conforme aux limites d'exposition pour les appareils portables RF pour les Etats-Unis et le Canada tablies pour un environnement non contrl. Le produit est sr pour un fonctionnement tel que dcrit dans ce manuel. La rduction aux expositions RF peut tre augmente si l'appareil peut tre conserv aussi loin que possible du corps de l'utilisateur ou que le dispositif est rgl sur la puissance de sortie la plus faible si une telle fonction est disponible.