FCC ID: V5PA800 Smart Payment Terminal

A800 Smart Payment Terminal

PAX Technology Limited

1. Checklist

Congratulations on receiving your PAX Technology payment terminal. We do hope you enjoy it!

The box you have just opened should contain the following items:

1 x PAX A800 Smart Payment Terminal

1 x Thermal Paper Roll

1 x AC Power Adapter

1 x Product Manual

1 x Cable

2. Installation

SAM/SIM/microSD Card:

① Remove the battery cover (At the bottom of the terminal).

② Insert the SAM/SIM card to the corresponding card slot.

Battery replacement:

a) Remove the battery cover (At the bottom of the terminal).

b) Remove the old battery: Unplug the battery connector and hold the battery then pull it out.

c) Replace with a new battery: align the battery in the battery compartments and hold the battery

connector then insert it into the power socket

3. Instructions

a）Power On/Off

Power on: Press the side ON/OFF button

terminal turns on successfully.

Power off: Press the side ON/OFF button

click“Power off” to shut down the terminal

b）Magnetic Stripe Card

two seconds until LCD backlight light, the

two seconds until the shutdown menu pops up,

Put magnetic stripe side of magnetic card towards device interior, swipe the card with a steady

speed during through magnetic reader slot.(Support bi-directional swiping)

c）IC Card

d）Contactless Card

Put IC card chip side upward, push-in IC card slot and to bottom.

Put the contactless card into the sensing area above the cover of the printer

e）Shred paper operating Instructions

Make paper 45 degrees angle right to paper knife and shred paper.

4. General Usage Tips

a) Avoid placing this product in direct sunlight for extended periods, nor in environments with

excessively high temperature, moisture or dust.

b) Only qualified personnel should repair this product.

c) Before using cards in the chip reader, please ensure it is free from any foreign objects.

5. Battery Usage Tips

WARNING:

a) The terminal is equipped with a non-removable built-in battery.

Do not replace the battery by yourself to avoid damaging the battery or the terminal.

b) Do not use the battery in direct sunlight or smoky and dusty environments.

c) Do not strike, squeeze or step on the battery, nor throw it into liquid or fire.

d) If the battery is deformed or damaged, replace immediately.

e) Any product warranty is only valid if batteries supplied by PAX Technology Limited are used.

f) Charging time should not exceed 24 hours. Over-charging or over-discharging may damage the

g) If the product is not being used for an extended period, whether in storage or otherwise, make

sure to recharge the battery at least every 6 months.

h) PAX Technology Limited advises that best-practice is to replace batteries every 2 years.

i) Dispose of batteries in a responsible manner

battery.

6. Icons

Dispose in a professional recycling manner

Class II equipment

For indoor use only

Energy efficiency marking

AC voltage

DC voltage

microSD logo

Trademark notice:

“microSD logo is a trademark of SD-3C LLC.”

FCC compliance statement

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two

conditions: (1) this device may not cause harmful interference, and (2) this device must accept any

interference received, including interference that may cause undesired operation.

changes or modifications not expressly approved by the party responsible for compliance could

void the user’s authority to operate the equipment.

This equipment has been tested and found to comply with the limits for a Class B digital device,

pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection

against harmful interference in a residential installation. This equipment generates, uses and can

radiate radio frequency energy and, if not installed and used in accordance with the instructions,

may cause harmful interference to radio communications. However, there is no guarantee that

interference will not occur in a particular installation.

If this equipment does cause harmful interference to radio or television reception, which can be

determined by turning the equipment off and on, the user is encouraged to try to correct the

interference by one or more of the following measures:

-- Reorient or relocate the receiving antenna.

-- Increase the separation between the equipment and receiver.

-- Connect the equipment into an outlet on a circuit different from that to which the receiver is

connected.

-- Consult the dealer or an experienced radio/TV technician for help.

ISED compliance statement

This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation,

Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the

following two conditions:

(1) This device may not cause interference.

(2) This device must accept any interference, including interference that may cause undesired

operation of the device.

L’émetteur/récepteur exempt de licence contenu dans le présent appareil est conforme aux CNR

d’Innovation, Sciences et Développement économique Canada applicables aux appareils radio

exempts de licence. L’exploitation est autorisée aux deux conditions suivantes :

(1) L’appareil ne doit pas produire de brouillage;

(2) L’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est

susceptible d’en compromettre le fonctionnement.

ISED 5G Wi-Fi statement

The user manual for LE-LAN devices shall contain instructions related to the restrictions

mentioned in the above sections, namely that:

i.

the device for operation in the band 5150–5250 MHz is only for indoor use to reduce the

potential for harmful interference to co-channel mobile satellite systems;

ii. where applicable, antenna type(s), antenna models(s), and worst-case tilt angle(s) necessary

to remain compliant with the e.i.r.p. elevation mask requirement set forth in section

6.2.2.3 shall be clearly indicated.

i.

ii.

le dispositif utilisé dans la bande 5150-5250 MHz est réservé à une utilisation en intérieur

afin de réduire le risque de brouillage préjudiciable aux systèmes mobiles par satellite

dans le même canal;

le cas échéant, le (s) type (s) d'antenne, le (s) modèle (s) d'antenne et l'angle (s) d'inclinaison

le plus défavorable nécessaire (s) pour rester conforme (e) au p.e. L'exigence relative au

masque d'élévation énoncée à la section 6.2.2.3 doit être clairement indiquée.

SAR statement

This equipment complies with FCC/ISED radiation exposure limits set forth for an

uncontrolled environment. End user must follow the specific operating instructions for

satisfying RF exposure compliance. This transmitter must not be co-located or operating

in conjunction with any other antenna or transmitter.

The portable device is designed to meet the requirements for exposure to radio waves

established by the ISED. These requirements set a SAR limit of 1.6 W/kg averaged over

one gram of tissue. The highest SAR value reported under this standard during product

certification for use when properly worn on the body.

Cet équipement est conforme aux limites d’exposition aux rayonnements FCC/ISED

établies pour un environnement non contrôlé. L’utilisateur final doit suivre les instructions

spécifiques pour satisfaire les normes. Cet émetteur ne doit pas être co-implanté ou

fonctionner en conjonction avec toute autre antenne ou transmetteur.

Le dispositif portatif est conçu pour répondre aux exigences d’exposition aux ondes radio

établie par le développement énergétique DURABLE. Ces exigences un SAR limite de

1,6 W/kg en moyenne pour un gramme de tissu. La valeur SAR la plus élevée signalée en

vertu de cette norme lors de la certification de produit à utiliser lorsqu’il est correctement

porté sur le corps.

PAX Technology Limited Date: 2021-07-06 TO:

Federal Communication Commission Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MID 21046 Regarding: FCC ID: V5PA800 To whom it may concern:

We, the undersigned, hereby authorize SGS-CSTC Standards Technical Services Co., Ltd. (SGS) Shenzhen Branch and Keny Xu in SGS-CSTC Standards Technical Services Co., Ltd. (SGS) Shenzhen Branch to act on our behalf in all manners relating to application for equipment authorization with respect to the FCC ID above, including signing of all documents relating to these matters. Any and all acts carried out by the agent on our behalf shall have the same effect as acts of our own. We, the undersigned, hereby certify that we are not subject to a denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 853(a). Where our agent signs the application for certification on our behalf, I acknowledge that all responsibility for complying with the terms and conditions for Certification, as specified by SGS North America, Inc., still resides with PAX Technology Limited. This authorization is valid until further written notice from the applicant. Print Name: Jenna Tan Title: Certification supervisor Signature:

On behalf of Company: PAX Technology Limited Telephone: 86-755-86156663 E-mail: certservice@paxsz.com

PAX Technology Limited

We, PAX Technology Limited declare that this EUT (FCC ID: V5PA800) doesn’t have ad

Hoc Mode function on “US/Canada frequencies“. In addition, the frequency selection feature

is disabled by firmware for devices marketed to the US/ Canada. For DTS part of this device,

only channels 1-11 will be used in North America. Country code selection is disabled.

Should you have any questions or comments regarding this matter, Please have my best

attention.

Sincerely yours,

Print Name: Jenna Tan

Title: Certification supervisor

Signature:

On behalf of Company: PAX Technology Limited

Telephone: 86-755-86156663

E-mail: certservice@paxsz.com

PAX Technology Limited

TO:

Federal Communication Commission

Equipment Authorization Branch

7435 Oakland Mills Road

Columbia, MID 21046

Regarding:

Confidentiality Request regarding application for FCC ID: V5PA800

LONG TERM CONFIDENTIALITY

Pursuant to 47 CFR Section 0.459 and 0.457 of the commission’s rules, the applicant hereby request confidential

treatment of the documents listed below, associated with the certification application referenced above.

The documents above contain proprietary information not released to the public. Public disclosure of this

information may prove harmful to the business of the applicant.

SHORT TERM CONFIDENTIALITY

Additionally, the applicant requests the following documents be held confidential until the device is marketed or

45 days from the grant date, whichever is less. If the device is marketed within 45 days of the Grant Date, the

applicant will notify the TCB per FCC KDB 726920 D01 Confidentiality Request Procedures.

Schematic(s)

Block Diagrams

Operational Descriptions

Tune up procedure Software

Security Description

External Photos

Internal Photos

Test Setup Photos

User manual(s)

Sincerely,

Signature:

Print Name: Jenna Tan

Title: Certification supervisor

On behalf of Company: PAX Technology Limited

Telephone: 86-755-86156663

E-mail: certservice@paxsz.com

Applicant Declaration Applicant Declaration Rev:0.0 SGS North America Inc. 620 Old Peachtree Road SUITE 100 Suwanee, Georgia 30024 United States Applicant Legal Business Name PAX Technology Limited Address Room 2416, 24/F., Sun Hung Kai Centre, 30 Harbour ，Hong Kong，China Grantee Code V5P FCC ID V5PA800 Authorized Contact Name Jenna Tan Contact Email certservice@paxsz.com Contact Phone 86-755-86156663 I, the undersigned, certify that I am an authorized signatory for the Applicant and therefore declare; a) in accordance with 47CFR2.911(d), all of the statements herein and the exhibits attached hereto are true and correct to the best of my knowledge and belief. b) in accepting a Grant of Equipment Authorization issued by a TCB, under the authority of the FCC, as a result of the representations made in this application, the Applicant is responsible for: (1) labeling the equipment with the exact FCC ID as specified in this application, (2) compliance statement labeling pursuant to the applicable rules, (3) compliance of the equipment with the applicable technical rules, c) if the Applicant is not the actual manufacturer of the equipment, appropriate arrangements have been made with the manufacturer to ensure that production units of this equipment will continue to comply with the FCC’s technical requirements. d) in accordance with 47 CFR 2.909 and KDB394321, the Applicant has read, understood and agrees to accept that they are the responsible party and agree to abide by their responsibilities as specified under 47 CFR 2.909 and KDB394321. e) in accordance with ISO17065, FCC KDB641163, FCC KDB610077, KDB394321 and RSP-100, the Applicant has read, understood, accepts and agrees to abide by the post market surveillance requirements. (1) the Applicant understands, accepts and agrees that a sample may be requested for surveillance testing. (2) the Applicant shall make provisions to always have a production sample available upon request by SGS, FCC and/or ISED. (3) the Applicant shall, upon request by SGS, at the Applicant’s expense, provide a production sample of the requested product to SGS, FCC and/or ISED as instructed. The sample shall include all support devices, cables, software, accessories or other hardware or software required for evaluation, review, certification and audit surveillance of products certified by SGS. f) neither the Applicant nor any party to the application is subject to a denial of Federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. §862 because of a conviction for possession or distribution of a controlled substance. See 47CFR 1.2002(b) for the definition of a “party” for these purposes. g) the Applicant has read, understood, accepts and agrees to abide by the SGS North America, Inc.(TCB) terms and conditions. Link to CFRs: https://www.fcc.gov/wireless/bureau-divisions/technologies-systems-and-innovation-division/rules-regulations-title-47 Link to KDBs: https://apps.fcc.gov/oetcf/kdb/index.cfm Link to RSP-100: https://www.ic.gc.ca/eic/site/smt-gst.nsf/eng/sf01130.html Applicant Signature: Date: July 6, 2021 Print Name: Jenna Tan Title: Certification supervisor *NOTE: This declaration cannot be signed by an Agent, it shall be signed by an authorized person listed in the FCC database