FCC ID: V5PIM154GBW UNATTENDED PAYMENT TERMINAL

Quick Setup Guide IM15 UNATTENDED PAYMENT TERMINAL PAX TECHNOLOGY LIMITED 1 1. CONTENTS Please make sure the following items are included with your IM15 unattended payment terminal. If any items are missing, contact your dealer. 1. 1 x IM15 Unattended Payment Terminal 2. 4 x M4 nuts 3. 4 x M4 screws 4. 1 x IM15 Mounting Bracket 2. PRODUCT DESCRIPTION Figure 1: front view 1. LCD touchscreen 2. speaker 3. proximity and light detector 4. LED status indicator 5. camera flash LED 6. camera lens 1. Digital IO port 2. 4G antenna connector(Not include SIM card slot for configuration with only Figure 2: back view BT/WIFI/NFC or with only NFC) 2 3. MDB port 4. status LED 5. USB Type-A port 6. back cover 7. reset button 8. USB Type-C port 9. RJ45 port (RS233) 10. RJ45 port (Ethernet) Hardware Version IM154GBW IM15BW IM15 Figure 3: view from all sides RF configuration BT+Wi-Fi+NFC+LTE BT+Wi-Fi+NFC NFC 3 3. INSTALLATION 1. SIM Cards(Not include SIM card slot for configuration with only BT/WIFI/NFC or with only NFC) Figure 4: accessing SIM card slot Remove the back cover to reveal the 4G board. Hold the antenna connector and pull the 4G board away from the body of the IM15. Flip the 4G board over to access the SIM card slot. Open the card slot and insert the card into the slot with the contacts facing towards the 4G board and with the clipped corner of the card aligned with the slot, then lock the mount with the card inside. 2. SAM Cards Figure 5: SAM card slots The 2 SAM cards slots of the IM15 can be seen while the back cover and 4G board are removed. To install a SAM card, open the card slot and insert the card into the slot with the contacts facing towards the IM15 and with the clipped corner of the card aligned with the slot, then lock the mount with the card inside. Note Do not power on the IM15 while installing or removing SIM or SAM cards. To reassemble the device, slot the 4G board into the board to board connector while aligning 4 notches on the board with 4 plastic tabs on the body of the IM15, then replace the back cover and screw it in place. 3. Device Dimensions 4 Figure 6: device dimensions (mm) 4. Device Installation Figure 7: device installation 1) The back face of the installation should have four stud bolts corresponding to the mounting points located on mounting bracket. Slide the mounting bracket into place with the orientation shown in figure 7 and then fix it in place with four M4 nuts. 2) Slide the IM15 unit into place with the orientation shown in figure 7. The back portion of the device should rest securely inside the mounting bracket. 3) Apply a torque of 0.6 to 0.8 Nm to each of the four M4 screws to secure the IM15 unit to its mounting bracket. 5 4. INSTRUCTIONS 1. Power on/off Power on:

Power off:

Plug the IM15 into an appropriate power source (12 to 48 VDC) via the MDB port, the digital IO port, or the RS232 RJ45 port. Disconnect the IM15 from the power source it is connected to. 2. Contactless Transactions When the device is ready to accept a contactless transaction, the contactless icon should appear on screen. Orient the card or NFC device parallel to the screen and then hold it at a distance of 4 cm or less directly above the contactless icon. 3. Code Scanner Transactions When the device indicates on screen that it is ready to scan a 1D or 2D code, orient the code parallel to the code scanning camera and then place it directly in front of the camera. 4. Environmental Conditions Storage Temperature:

Operating Temperature:

Relative Humidity:

-30C ~ 70C (-22F ~ 158F)

-20C ~ 70C (-3F ~ 158F) 5% ~ 95% (non-condensing) 5. MAINTENANCE AND USAGE If any cables become damaged, seek a replacement. 1. 2. Do not insert unknown materials into any port on the IM15, this may cause serious damage to the device. 3. Only qualified personnel should repair this product. 4. Frequency from 5150 to 5250MHz is for indoor useduring normal use IM15 surface should still be keep clear of dirt and possible liquid contaminants. 5. While the IM15 is designed to resist ingress of dust and liquids, it is not designed to resist pressurized liquids such as water hoses. Keep the back of the device away from dust and liquids as much as possible. 6. Make sure the various cables connect to provide the appropriate voltages at the proper 7. pins. If the IM15 requires repair, contact a professional technician instead of attempting them yourself 6. COMPLIANCE STATEMENTS FCC COMPLIANCE STATEMENT This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1) 2) this device may not cause harmful interference this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. 3) Frequency from 5150 to 5250MHz is for indoor use. 6 Warning This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. Caution Any changes or modifications not expressly approved by the manufacturer could void the user's authority to operate this equipment. Radiation Exposure This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator and your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. INDUSTRY CANADA STATEMENT licence-exempt transmitter(s)/receiver(s) that comply with This device contains Innovation, Science and Economic Development Canadas licence-exempt RSS(s). Operation is subject to the following two conditions:

1) this device may not cause interference, and 2) this device must accept any interference, including interference that may cause undesired operation of the device. Le prsent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorise aux deux conditions suivantes:

1) 2) l'appareil ne doit pas produire de brouillage, et l'utilisateur de l'appareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible d'en compromettre le fonctionnement. The user manual for LE-LAN devices shall contain instructions related to the restrictions mentioned in the above sections, namely that i. the device for operation in the band 51505250 MHz is only for indoor use to reduce the potential for harmful interference to co-channel mobile satellite systems;

le dispositif utilis dans la bande 5150-5250 MHz est rserv une utilisation en intrieur afin de rduire le risque de brouillage prjudiciable aux systmes mobiles par satellite dans le mme canal;

Note: The above description only applies to IM15 BW, IM15 4GBW. i. 7 This device and its antenna(s) must not be co-located or operating in conjunction with any other antenna or transmitter, except tested built-in radios. Cet appareil et son antenne ne doivent pas tre situs ou fonctionner en conjonction avec une autre antenne ou un autre metteur, exception faites des radios intgres qui ont t testes. The Country Code Selection feature is disabled for products marketed in the US/Canada. La fonction de slection de lindicatif du pays est dsactive pour les produits commercialiss aux tats-Unis et au Canada. Radiation Exposure Statement This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. Dclaration d'exposition aux radiations Cet quipement est conforme aux limites d'exposition aux rayonnements IC tablies pour un environnement non contrl. Cet quipement doit tre install et utilis avec un minimum de 20 cm de distance entre la source de rayonnement et votre corps. 7. INDEX OF ICONS do not throw away, requires professional recycling Class II equipment for indoor use only energy efficiency marking (level VI) AC voltage DC voltage Although PAX Computer Technology (Shenzhen) Co., Ltd. strives to maintain the accuracy of the information presented in this document, it reserves the right to change product specifications without prior notification and does not guarantee that the material presented herein will accurately reflect the set up, installation, or use of PAX products. 8 Manufacture:

Address:

Tel:

Website:

PAX Computer Technology (Shenzhen) Co. Ltd. 4FL, Building #3, Software Park, 2nd Central Science-Tech RD, High-Tech Industrial Park, Shenzhen, Guangdong, PRC.

+86 755-86169630 www.pax.com.cn Responsible Party: PAX Technology Inc. Address:

8880 Freedom Crossing Trail, Building 400, 3rd Floor, Suite 300, Jacksonville, Florida 32256 1-877-859-0099 www.pax.us Tel:

Website:

9

PAX Technology Limited Date: 2022-2-20 TO:

Federal Communication Commission Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MID 21046 Regarding: FCC ID: V5PIM154GBW To whom it may concern:

We, the undersigned, hereby authorize Compliance Certification Services (Kunshan) Inc and winkey wang in Compliance Certification Services (Kunshan) Inc to act on our behalf in all manners relating to application for equipment authorization with respect to the FCC ID above, including signing of all documents relating to these matters. Any and all acts carried out by the agent on our behalf shall have the same effect as acts of our own.. We, the undersigned, hereby certify that we are not subject to a denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 853(a). Where our agent signs the application for certification on our behalf, I acknowledge that all responsibility for complying with the terms and conditions for Certification, as specified by SGS North America, Inc., still resides with PAX Technology Limited This authorization is valid until further written notice from the applicant. Print Name: Jenna Tan Title: Certification Leader Signature:

On behalf of Company: PAX Technology Limited Telephone: 86-755-86156663 E-mail: certservice@paxsz.com

PAX Technology Limited TO:

Federal Communication Commission Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MID 21046 Regarding:

Confidentiality Request regarding application for FCC ID: V5PIM154GBW LONG TERM CONFIDENTIALITY Pursuant to 47 CFR Section 0.459 and 0.457 of the commissions rules, the applicant hereby request confidential treatment of the documents listed below, associated with the certification application referenced above. Schematic(s) Block Diagrams Operational Descriptions Software Security Description The documents above contain proprietary information not released to the public. Public disclosure of this information may prove harmful to the business of the applicant. SHORT TERM CONFIDENTIALITY Additionally, the applicant requests the following documents be held confidential until the device is marketed or 0 days from the grant date, whichever is less. If the device is marketed within 0 days of the Grant Date, the applicant will notify the TCB per FCC KDB 726920 D01 Confidentiality Request Procedures. External Photos Internal Photos Test Setup Photos User manual(s) Sincerely, Print Name: Jenna Tan Title: Certification Leader Signature:

On behalf of Company: PAX Technology Limited Telephone: 86-755-86156663 E-mail: certservice@paxsz.com

SGS North America Inc. 620 Old Peachtree Road SUITE 100 Suwanee, Georgia 30024 United States Applicant Declaration Applicant Legal Business Name PAX Technology Limited Address Grantee Code FCC ID Room 2416, 24/F., Sun Hung Kai Centre, 30 Harbour Hong Kong V5P V5PIM154GBW Authorized Contact Name Jenna Tan Contact Email Contact Phone certservice@paxsz.com 86-755-86156663 I, the undersigned, certify that I am an authorized signatory for the Applicant and therefore declare;

a) b) c) d) e) in accordance with 47CFR2.911(d), all of the statements herein and the exhibits attached hereto are true and correct to the best of my knowledge and belief. in accepting a Grant of Equipment Authorization issued by a TCB, under the authority of the FCC, as a result of the representations made in this application, the Applicant is responsible for:

labeling the equipment with the exact FCC ID as specified in this application,

(1)

(2) compliance statement labeling pursuant to the applicable rules,

(3) compliance of the equipment with the applicable technical rules, if the Applicant is not the actual manufacturer of the equipment, appropriate arrangements have been made with the manufacturer to ensure that production units of this equipment will continue to comply with the FCCs technical requirements. in accordance with 47 CFR 2.909 and KDB394321, the Applicant has read, understood and agrees to accept that they are the responsible party and agree to abide by their responsibilities as specified under 47 CFR 2.909 and KDB394321. in accordance with ISO 17065, FCC KDB641163, FCC KDB610077, KDB394321 and RSP-100, the Applicant has read, understood, accepts and agrees to abide by the post market surveillance requirements.

(1)

(2)

(3) the Applicant understands, accepts and agrees that a sample may be requested for surveillance testing. the Applicant shall make provisions to always have a production sample available upon request by SGS, FCC and/or ISED. the Applicant shall, upon request by SGS, at the Applicants expense, provide a production sample of the requested product to SGS, FCC and/or ISED as instructed. The sample shall include all support devices, cables, software, accessories or other hardware or software required for evaluation, review, certification and audit surveillance of products certified by SGS. f) g) neither the Applicant nor any party to the application is subject to a denial of Federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 862 because of a conviction for possession or distribution of a controlled substance. See 47CFR 1.2002(b) for the definition of a party for these purposes. the Applicant has read, understood, accepts and agrees to abide by the SGS North America, Inc.(TCB) terms and conditions. Link to CFRs: https://www.fcc.gov/wireless/bureau-divisions/technologies-systems-and-innovation-division/rules-regulations-title-47 Link to KDBs: https://apps.fcc.gov/oetcf/kdb/index.cfm Link to RSP-100: https://www.ic.gc.ca/eic/site/smt-gst.nsf/eng/sf01130.html Link to the Covered List: Covered List

[PAX Technology Limited] (the applicant) certifies that the equipment for which authorization is sought is not covered equipment prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules.

[PAX Technology Limited] (the applicant) certifies that, as of the date of the filing of the application, the applicant [is not] identified on the Covered list, established pursuant to 1.50002, as an entity producing covered equipment. Applicant Signature:

Date:

2023/3/13 Print Name:

Title:

Jenna Tan Certification Leader

*NOTE: This declaration cannot be signed by an Agent, it shall be signed by an authorized person listed in the FCC database QSF27-14-04 Rev 1.0 Rev. Feb 6, 2023 Page 1 of 1 Original Issue: Jan. 4, 2021

UNITED STATES DESIGNATED AGENT LETTER TO: Federal Communication Commission Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MID 21046 Applicant Company Name:

Grantee Code:

Contact Name:

Address:

City/Province/Zip:

Telephone:

Fax:

Email:

PAX Technology Limited V5P Jenna Tan Room 2416, 24/F., Sun Hung Kai Centre, 30 Harbour Hong Kong 0755-86169676 0755-86155423 certservice@paxsz.com ATTN: Director of Certification:

We, PAX Technology Limited and John Hallisey understand and acknowledge the applicants consent and Date: Mar., 09, 2023 U.S. designated agent Company Name:

FRN:

Contact Name:

Address:

City/Province/Zip:

Telephone:

Fax:

Email:

Pax Technology, Inc. 0033507476 John Hallisey 8775 Baypine Road Jacksonville, FL 32256 904-302-9424 904-900-3751 John.Hallisey@pax.us the designated agent's obligation to accept service of process in the United States for matters related to the applicable equipment, and at the physical U.S. address and e-mail of the designated agent listed above. We, PAX Technology Limited and John Hallisey acknowledge the applicant's acceptance of its obligation to maintain an agent for service of process in the United States for no less than one year after either the grantee has permanently terminated all marketing and importation of the applicable equipment within the U.S., or the conclusion of any Commission-related administrative or judicial proceeding involving the equipment, whichever is later. Applicant Name (Printed): Jenna Tan Title: Certification Leader Signature:

Jesen Tao U.S. designated agent Name (Printed): John Hallisey Title: General Counsel Signature: