FCC ID: 2ARTP-PT82 Personal Communications Tablet

Users Manual PT82 Version 1.0 01/2023 All rights reserved. Copyright 2023 No part of this document may be reproduced, stored in a retrieval system, or transmitted in any form, by any means

(electronic, photocopying, recording, or otherwise) without the prior written permission of the publisher. Copyright protection claimed includes all forms and matters of copyrightable material and information allowed by statutory or judicial law or hereafter granted, including without limitation, material generated from the software programs which are displayed on the screen such as screen displays, menus, etc. Products that are referred to in this document may be either trademarks and/or registered trademarks of the respective owners. The publisher and the author make no claim to these trademarks. While every precaution has been taken in the preparation of this document, the publisher and the author assume no responsibility for errors or omissions, or for damages resulting from the use of information contained in this document or from the use of programs and source code that may accompany it. In no event shall the publisher and the author be liable for any loss of profit or any other commercial damage caused or alleged to have been caused directly or indirectly by this document. Content subject to change without notice. 2 Table of Contents Contents Table of Contents .............................................................................................................................................................. 3 1. Introduction .......................................................................................................................................................... 4 Explanation of Advisements ................................................................................................................................. 4 Symbols and Markings ......................................................................................................................................... 4 2. Device Layout ....................................................................................................................................................... 5 Front and side views ............................................................................................................................................. 5 Rear View ............................................................................................................................................................. 6 3. Managing Device Power ....................................................................................................................................... 6 Docking station ..................................................................................................................................................... 6 Power Supply and Batteries .................................................................................................................................. 7 Checking the charging Level ...................................................................................................................................... 8 Power LED Behavior on the Docking station ............................................................................................................. 8 4. Using the PT82 .................................................................................................................................................... 8 Starting the Device .............................................................................................................................................. 8 Shutting Down the PT82 ....................................................................................................................................... 8 Power Saving ........................................................................................................................................................ 8 Using the Camera ................................................................................................................................................ 8 Adjusting the Volume .......................................................................................................................................... 9 5. Product Care ......................................................................................................................................................... 9 Temperature & Humidity ..................................................................................................................................... 9 General Use Operating temperature ...................................................................................................................... 9 Transportation and Storage ...................................................................................................................................... 9 Transporting the PT82 Device ............................................................................................................................. 9 6. 7. Safety .................................................................................................................................................................... 9 Trouble shooting ................................................................................................................................................ 11 Appendix A Technical Specifications ............................................................................................................................ 12 Appendix B Compliance Information ........................................................................................................................... 12 B1 FCC Statement ............................................................................................................................................... 12 Part 15B Equipment ................................................................................................................................................ 13 FCC RF Radiation Exposure Statement: .................................................................................................................. 13 B2 Radio Wave Exposure and Specific Absorption Rate (SAR) Information........................................................ 13 3 1. Introduction Welcome to your PT82 Tablet PC. To ensure the optimal performance of this product, please take the time to read this manual carefully. The PT82 is a rugged tablet designed for use in correctional facilities. Explanation of Advisements In this manual we use three (3) levels of Advisements as follows:

The Note symbol is used for notifying the user of something important or of something that needs special attention. The Caution symbol is used to inform of something that could cause harm to normal function of the equipment. The Warning symbol is used to inform of something in which there is a conceivable risk of harm to the user if the Warning is ignored. Symbols and Markings This section provides information about the symbols that are used on the PT82, its accessories, or packaging. Symbol or Markings Description Power On/Off Indicator Dispose of in accordance with your country's requirements. This is a certification mark employed on electronic products manufactured or sold in the United States which certifies that the electromagnetic interference from the de-

vice is under limits approved by the Federal Communications Commission. 4 2. Device Layout Front and side views Component MIC Front Camera Charge LED Indicator MIC Speaker Lock Docking Connector Headset Telephone Receiver Volume + Button Volume Button Power Button Description Audio Recording Device Record Still and Video Images White Blinking Light Battery Charging Solid Green Charge Complete Red Blinking Light Low Battery (Battery Below 10%) Audio Recording Device Sends Out Audio For locking tablet in associated wall charger. When it is under Lock mode, the tablet cannot be taken out from the wall charger. Connects the tablet with the Tablet Docking Station Connect headphone Handset function for voice calls Increases the audio volume Decreases the audio volume Turn power On/Off (Hold 10s to Reset) 5 Rear View Component SN Label Description Position to place SN Label 3. Managing Device Power Docking station You can charge the PT82 tablet using a Docking station. The docking station has a DC input and a USB Port, the docking connecter is shown in the layout Front view in chapter 2. 6 Use only the docking station included with your Tablet PC. Using other docking stations may damage the device. Power Supply and Batteries The PT82 device has one rechargeable battery. Android OS will give battery warnings at certain battery levels. If the PT82 device is not charged or powered by the power supply, the PT82 device will shut down automatically. For more information, more details about the specification, please see Appendix A Technical Specifications To charge the Battery Pack:

1. 2. 3. Connect the tablet to the docking station using docking connector. Connect the docking station to an electrical outlet and charge the tablet until the battery is fully charged. After your device is fully charged, disconnect the charger from both the device and the electrical outlet. NOTE: To prevent damage to batteries, please see Section 8: Safety You cannot overcharge the battery. It is fine to charge the battery overnight. Battery life naturally degrades over time. Failure to follow instructions for recommended operating temperatures, charge and discharge rates, and other instructions may accelerate battery decay rates. If your tablet battery will not accept or hold a satisfactory charge, it may need to be replaced. For battery storage and charging temperatures, see Section 8: Safety 7 Checking the charging Level To check the battery charge level of the PT82, the battery monitor is shown on the Android Top navigation bar. Power LED Behavior on the Docking station The Power LED will only shine when the Power adapter is plugged in. Green Fully charged Blue Charging 4. Using the PT-82 No special skills are required to setup the PT82 device. Follow this Users Manual and the Quick Start Manual. Starting the Device Start the device by pressing the power button on the top of the device. Shutting Down the PT-82 The device should be shut down in the following way:

Use the menu in Android OS. Hold the power button for 3 seconds then select Power Off/Shutdown.

(recommended when possible). Should you be unable to shut the device down using the above, you can hold the power button on the top side of the device down for more than 10 seconds. The device will consequently shut down immediately, without waiting for open applications to close. Reset can be performed by holding the power button on the top side of the device for five (5) seconds. Using the physical power button to turn off the device is not considered a "clean" shut down, and is thus not recommended unless completely necessary because it can harm your device. Power Saving The Power saving settings in the PT82 tablet are preset to optimize the battery runtime. Using the Camera The builtin camera allows you to take snapshots or video of items from the display side. 8 Adjusting the Volume To adjust the volume, use the Volume Up and Down buttons on the upper side of the PT82 device. For position references, see the layout in Chapter two. Volume adjustments can also be adjusted in Android OS. 5. Product Care Temperature & Humidity General Use - Operating temperature The PT82 is best kept in dry conditions at room temperature. The recommended range for temperature and the humidity value for the device is as follows:

Ambient temperature: 0 to 35 (32 to 95) Relative humidity: 10% to 90% (no condensation on the device) Atmospheric Pressure: 80 kPa to 106 kPa (600 mmHg to 795 mmHg) Transportation and Storage For transportation and storage, the recommended range for temperature and the humidity value for the device is as follows:

Temperature: 20 to 60 (4 to 140) Relative humidity: 10% to 90% (no condensation on the device) Transporting the PT-82 Device Disconnect all the cables from the PT82 while carrying the device. When you transport the device for any reason, use the original casing and packaging materials where possible. It is recommended to keep the original packaging materials for the PT82. If the device needs to be returned to the Device Manufacturer for Warranty related issues or repair, it is recommended that the original packaging or equivalent is used for shipping. Most shipping carriers recommend at least 2 inches of packing material around the device. Due to Joint Commission regulations, any shipping materials including boxes sent to the Device Manufacturer must be discarded and will be replaced. 6. Safety The PT82 device has been tested and approved as compliant to all the Specifications and Standards listed in Appendix B Compliance Information, and in the Appendix A Technical Specifications. Nevertheless, to ensure safe operation of your PT82 device, there are a few safety warnings to bear in mind:

Do not disassemble this product. You may receive an electric shock, or foreign matter may enter and result in a fire. If a malfunction or trouble occurs, immediately turn the power off and unplug 9 any power sources. Then contact your suppliers technical support office for repair. Do not service or perform maintenance on the device while the device is in use. Make sure to shut the device down and unplug all cables before starting and service or maintenance work on the device. 2.1 Power Supply and Batteries The PT82 device contains one rechargeable battery. All rechargeable batteries degrade over time. Thus, the possible usage times for the PT82 after a full charge can become shorter over time compared to when the device was new. The PT82 device uses a Liion Polymer battery. If you are in a hot environment, be aware that it can affect the ability to charge the battery. The internal temperature must be between 0 /32 and 45 /113 for the battery to charge. If the internal battery temperature rises above 45 /113 the battery will not charge at all. Avoid exposing the PT82 device to fire or to temperatures above 60 /140 . These conditions may cause the battery to malfunction, generate heat, ignite, or explode. Be aware that it is possible, in a worstcase scenario, for temperatures to reach greater than those stated above in, for example, the trunk of a car on a hot day. Only charge the PT82 battery in an ambient temperature of 0 /32 to 45 /113 . Use only the supplied power adapter to charge the PT82 device. Using unauthorized power adapters may severely damage the PT82 device. For safe operation of the PT82 device, use only charger and accessories approved by Device Manufacturer. If the Power Supply Cord is damaged it needs to be replaced by Service Personnel only. Do not use the Power Supply Cord until replaced. Disconnect the AC power plug of the Power adapter from the wall socket when not charging the device and disconnect the power cable from the device. Special regulations apply to shipping devices containing LiIon Polymer batteries. If dropped, crushed, or short circuited, these batteries can release dangerous amounts of heat, may ignite, and/or may be dangerous near fires. The plug/adapter plug pins insulate the device from the power supply. Do not position the device in a position where it is difficult to disconnect the device from power safely terminate operation of the device. 2.2 Temperature 10 Use in direct sunlight or in any other hot environment may cause the PT82 device to develop hot surfaces. There is a builtin temperature sensor that monitors the device temperature. If the sensor detects high internal temperature; the device will automatically trigger a Shut Down. It may take a while before PT82 device can be restarted as the unit may first need time to cool down. 2.3 Electricity The device contains no user serviceable parts. Do not open the case of the PT82 Tablet Device. Doing so will void the product warranty and may expose you to electrical hazards. 2.4 Software Using an antivirus program is strongly recommended. Software other than that which is preinstalled on the PT82 is installed at the user's own risk. External software could cause the PT82 to malfunction and might not be covered by the warranty. 2.5 Magnetic Field The PT82 device contains magnets. Magnetic fields may interfere with pacemakers, defibrillators, or other medical devices. As a rule, maintain a minimum distance of 6 inches (15 centimeters) between any item with magnets and a heart device. 2.6 Third Party Any use of the PT82 outside the intended use and together with any thirdparty software or hardware that changes the intended use voids the responsibility of the device manufacturer. 7. Trouble shooting In most cases, restarting your device will resolve any problem. To restart your device, hold the power button for 5 seconds, then select Shut down/Restart. If your device has crashed (and displays nothing on the screen), hold down the power button for 10 seconds to hard shutdown. Press the power button again to turn the PT82 back on. If this does not fix the problem, contact your supplier. Please have your serial number ready. This can be found on the back of your device. 11 Appendix A Technical Specifications Processor:

Touch Screen:

Top Glass:

Audio jack:

OS:

System Memory:

Storage:

LCD:

RK3566 Quadcore CortexA55 Mali-G52 GPU Android 11 3GB LPDDR4 16G eMMC 8 LCD 800 x 1280 resolution Multitouch capacitive PMMA+PC Headphone and Microphone 3.5 mm 1xSpeaker, 1xHeadset Front camera: 5M Imaging/input:

WiFi6: IEEE 802.11.ax Wireless:

Sensors:

3axis accelerometer Light sensor 3200mA 7.4V battery, 23.7w Battery:

Support 12v in and USB function Dock:

Charging LED LED:

Chassis:

Front chassis: Dual injection molding Rear chassis: ABS+PC Operating Temperature: 040C Durability:

Storage Temperature: 2060 C Humidity: 10% to 90%

Drop: 3FT drop resistant on 4 corners ROHS: Compliant ESD protection: 6K touch, 8KV air IATA FCC Regulatory Cert:

Appendix B Compliance Information B1 FCC Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) this device may not cause harmful interference and (2) this device must accept any interference received, including interference that may cause undesired operation. 12 Modifications not expressly approved by Device Manufacturer could void the users authority to operate the equipment under FCC rules. Part 15B Equipment This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna. Connect the equipment into an outlet on a circuit different from that to which the receiver is Increase the separation between the equipment and receiver. connected. Consult the dealer or an experienced radio/TV technician for help. The device for operation in the band 51505250 MHz is only for indoor use FCC RF Radiation Exposure Statement:

B2 Radio Wave Exposure and Specific Absorption Rate (SAR) Information The SAR (Specific Absorption Rate) limit as dictated by the FCC (in the USA) is 1.6W/kg averaged over 1 gram of tissue. with FCC RF exposure requirements. have been tested against these SAR limits to maintain compliance The Devices, PT82 This equipment complies with FCC RF radiation exposure limits set forth for environment. an uncontrolled The highest reported SAR level for usage near the body (0mm) is 1.172 W/kg 13

Pay Tel Communications, Inc. Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Date: March 30, 2023 SUBJECT: FCC Application for (FCC ID: 2ARTP-PT82) To Whom It May Concern:

We, the undersigned, hereby authorize Mina Xu at Centre Testin International Grou Co. Ltd/ Buildin C Hon wei Industrial Park Block 70 Bao'an District Shenzhen China on our behalf, to apply to the Federal Communications Commission on our equipment. Any and all acts carried out by Mina Xu at Centre Testin International Grou Co. Ltd /

Buildin C Hon wei Industrial Park Block 70 Bao'an District Shenzhen China on our behalf shall have the same effect as acts of our own. This is to advise that we are in full compliance with the Anti- Drug Abuse Act. We, the applicant, are not subject to a denial of federal benefits pursuant to Section 5301 of the Anti-Drug Act of 1988, 21 USC853a, and no party to the application is subject to a denial of federal benefits pursuant to that section. Regards, printed name: Rick Lubbehusen C:\Users\rlubbehusen\A ppData\Local\Microsoft\Windows\INetCache\Content.Outlook\GC46SROE\POA Letter.docx

fo Pay Tel Communications, Inc. Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 USA Date: March 21, 2023 FCC ID: 2ARTP-PT8&2 Pay Tel Communications, Inc (the applicant) certifies that, as of the date of the filing of the application, we designate ourselves as the U.S. agent for service of process. Designated U.S. Agent Information:

FRN: 0028011476 Name: Pay Tel Communications, Inc. Address: PO Box 8179,Greensboro North Carolina 27419 United States Contact Person: Rick Lubbehusen Tel.: 336 852 7419 Extension: 325 Email: RLubbehusen@paytel.com Sincerely, Pay Tel Communications, Inc. Rev 1/26/2023 printed name: Rick Lubbehusen Ref: Attestation Statements Part 2.911(d)(7) Filing

Pay Tel Communications, Inc. Federal Communications Commission Date: 2023-03-30 Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 To Whom it may concern, We, as the grantee of this project, would like to declare that this device has been tested according to the FCC requirement and found compliant with the following standards: FCC Part 15 Subpart B. Product Name Personal Communications Tablet Brand Name > N/A Model Name PT-82 Testing Lab . Centre Testing International Group Co., Ltd Company Name : Pay Tel Communications, Inc. Name : Rick Lubbehusen Job Title : Senior Director of Business E-mail : fubbehusen@paytel.com Tel. 336 852 7419 Extension: 325 SUBJECT: FCC SDoC declaration for FCC ID: 2ARTP-PT82

Pay Tel Communications, Inc. Federal Communications Commission Authorization and Evaluation Division Confidentiality Request regarding application for certification of FCC ID: 2ARTP-PT82 Pursuant to Sections 0.457 and 0.459 of the Commissions Rules, we hereby request confidential treatment of information accompanying this application as outlined below:

Exhibit Type File Name

(Block Diagram, Schematics, Operational (Block Diagram-.pdf, Schematics.pdf, Description, Software Security Description) Operational Description.pdf, Software Security Description.pdf) The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these materials may be harmful to the applicant and provide unjustified benefits to its competitors. The applicant understands that pursuant to Section 0.457 of the Rules, disclosure of this application and all accompanying documentation will not be made before the date of the Grant for this application. Pursuant to DA04-1705 June 15, 2004 of the Commissions public notice, we also request temporary confidential treatment of information accompanying this application as outlined below:

Exhibit Type File Name

Sincerely, Signature:

printed name: Rick Lubbehusen Date: March 30, 2023 Rev 11/20/07

Sincerely, Signature:

Pay Tel Communications, Inc. Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 USA Date: March 30, 2023 Ref: Attestation Statements Part 2.911(d)(5)(i) Filing FCC ID: 2ARTP-PT82 Pay Tel Communications, Inc (the applicant) certifies that the equipment for which authorization is sought is not covered equipment prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules. Rev 2/17/2023 Printed name: Rick Lubbehusen Pay Tel Communications, Inc. Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 USA Date: March 30, 2023 Ref: Attestation Statements Part 2.911(d)(5)(ii) Filing FCC iD: 2ARTP-PT82 Pay Tel Communications, Inc (the applicant) certifies that, as of the date of the filing of the application, the applicant is not identified on the Covered List as an entity producing covered equipment. Sincerely, Signature:

Rev 2/17/2023 Printed name: Rick Lubbehusen