Bluetooth Module RM3030 Users Guide Introduction You can connect to other Bluetooth wireless devices by integrating the RM3030 module to your device. Specification Product Name Model Number Standard Frequency Band Transfer rates (Max) Antenna terminal Dimension Operating Temperature Storage Temperature Humidity Bluetooth Module RM3030 Bluetooth v4.0 2.402GHz ~ 2.480GHz unlicensed ISM band Max UART baud rates up to 4Mbits/s 50 Ohms 12.5 x 16.6 mm
-10 ~ +50
-40 ~ +70 5 ~ 95% (non-condensing) Pin Assignment NO. Pin Name 1 2 3 GND NC PIO[0]
Description Ground No connect Programmable input/output line and 32kHz sleep clock input UART data input, active high UART data output, active high UART request to send, active low UART clear to send, active low No connect No connect No connect No connect No connect No connect No connect Programmable input/output line Power supply UART_RX 4 UART_TX 5 UART_RTS 6 UART_CTS 7 NC 8 NC 9 10 NC 11 NC 12 NC 13 NC 14 NC 15 PIO[9]
16 VDD 17 VREG_EN_RST# Take high to enable internal regulators. Also 18 VDD 19 NC acts as active low reset Power supply No connect 20 NC 21 GND No connect Ground Module Installation Manual Material:
Description BT_CSR PCBA Qty:1 Shielding Case Qty:1 Picture Description Qty:1 Picture Tools:
Description Picture Description Picture Iron Fan Tin wire Description Job Type:
Put BT_CSR PCBA on board, solder fixed, avoid short circuits. Note:
Welding BT_CSR PCBA temperature of 3500C 100C, not too high or too low. Job Type:
The Shielding Case welded on BT_CSR PCBA, careful not to short circuit and BT_CSR PCBA. Note:
1 Welded shielding case temperature of 3500C 100C, not too high or too low. 2 Shielding Case not skew or subsidence short circuit. Job Description and Notes:
Step Picture 01 02 Requires a clearance, Avoid short circuit Description 1. Welded shielding case temperature of 3500C 100C, not too high or too low. 2. Welding BT_CSR PCBA temperature of 3500C 100C, not too high or too low. 3. Welding BT_CSR PCBA requires a clearance and avoid short circuit. 4. Shielding Case not skew or subsidence short circuit. Finished:
Picture Requires a clearance, Avoid short circuit Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This device and its antenna(s) must not be co-located or operating in conjunction with any other antenna or transmitter. IMPORTANT NOTE:
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. LABEL OF THE END PRODUCT:
The final end product must be labeled in a visible area with the following " Contains TX FCC ID: SBC-RM3030 ".