FCC ID: 2AXD6-JS1000 Multi-function Jump Starter

DMARREUR + CHARGEUR SANS FIL JUMP STARTER WIRELESS CHARGER 12V CAR JUMP STARTER &

PORTABLE POWER BANK WITH WIRELESS CHARGING 4010229 INSTRUCTI ON MANUAL model no. ENJ1000 IMPORTANT:

Please read this manual carefully before operating this jum I N O T A M R O F N I Y T E F A S 2 WARNING model no. ENJ1000 | contact us 1-866-295-6775 Always wear safety glasses when jump starting a battery, and gloves when handling a battery. When jump starting a vehicle please ensure that the clamp connection is securely fitted into the jump starter socket. Ensure the battery clamps are connected correctly, and the connectors are free from rust and dirt. Do not allow this product to become wet. Do not immerse the product in water. Do not operate the product in explosive atmospheres, such as in the presence of flammable liquid, gas or dust. Do not modify or disassemble this product. Do not store in locations where the temperature may exceed 140F (60C). Charge only using the charger provided. Under extreme heat conditions, battery leakage may occur. Avoid contact with your skin. In case of skin or eye contact, rinse immediately with clean water and seek medical attention. BATTERY DISPOSAL The battery is self-contained and not consumer replaceable. The battery must be disposed of properly when it no longer holds a charge. Proper charging practices will increase the life of the product. For Information on battery recycling, call toll-free 800-822-8837. For information regarding air travel safety with batteries please reference this website by the U.S. Department of Transportation:

http://phmsa.dot.gov/safetravel/batteries NOTE: This Car jump starter and portable power bank contains the equivalent of 2.4g of lithium and gives 26.7 watt hours of power. PROP 65 WARNING This product contains lead, a chemical known to the state of California to cause cancer, birth defects or other reproductive harm. TO CHARGE YOUR JUMP STARTER At home:

1. Plug the AC Power Adaptor into any 120V outlet. 2. Attach the DC plug into the USB-C port on the Power Bank with the equipped USB-A to USB-C cable In the Car:

1. Plug the car adaptor into the socket of cigarette lighter. 2. Attach the DC plug into the USB-C port on the Power Bank with the equipped USB-A to USB-C cable. 3 I G N G R A H C TO POWER YOUR MOBILE DEVICES Use the original manufacturer's USB cable that came with your device and plug it into the USB output ports. The USB charging port can charge at 5V/2A, 9V/2A or 12V/2A compatible Quick Charge technology devices or charges nonQuick Charge devices at up to 2.4A. Once you charge your device, the power level gauge will show the battery level. To check the power capacity again, simply press the power button once. TO CHARGE USING WIRELESS CHARGING SURFACE Make sure your device is Qi-compatible. If the case is metal, remove prior to charging. If you are having issues charging, remove your case and try again. Place the Qi-

compatible device directly onto the indicated wireless charging icon. Your device will display the charging progress. Charging time will depend on the type of device. Do not place magnetic cards or similar items near this product. Place the unit on a sturdy and flat surface during charging. Keep the unit out of reach of children 4 S T N E T N O C E G A K C A P model no. ENJ1000 | contact us 1-866-295-6775 1 Portable charger/wireless 4 Jumper cable PACKAGE CONTENTS charger 2 USB-A to USB-C cable 3 Car DC charger 2 JUMP STARTER WIRELESS CHARGER DMARREUR CHARGEUR SANS FIL

1 4 3 PRODUCT SPECIFICATION Product Dimensions: 5.35 x 2.99 x 0.98 inch (136 x 76 x 25 mm) Product Weight: 0.68 lbs (310g) Multi-function Jump Starter Dmarreur Batterie Multi-

fonction Cap.: 7,200mAh Input (TypeC): 5V/2.4A, 9V/2A Output: QC3.0 Temp: -13F to 104F / -25C to 40C Start Current:

16V/500A Peak Current: 16V/1000A USB: QC3.0, 5V/2A, 9V/2A, 12V/2A E Battery level indicator F Wireless charging surface G Battery clamps with cross polarity protection 5 I I I S N O T A C F C E P S T C U D O R P FUNCTIONALITIES A Power & LED light button B USB output port C Jumpstarter connection port 9V/2A D Input (TypeC): 5V/2.4A, F A B C D G E POWER LEVEL GAUGE LIGHTS Press the power button to check the capacity of the Power Bank Indicator Lights 1 Flashing 1 Solid 2 Solid 3 Solid 4 Solid Battery Capacity Below 5%

5-25%

26-50%

51-75%

76%-full When charging, the indicator gauge will light up one by one. The number of stable lights show the battery capacity. When all the indicator lights are firm, then the Power Bank is fully topped up. I G N T R A T S P M U J 6 model no. ENJ1000 | contact us 1-866-295-6775 IN ORDER TO JUMP START THE AUTOMOBILE BATTERY, FOLLOW THESE INSTRUCTIONS 4. Fasten the BLACK jumper cable to the NEGATIVE (-) post on the car battery.The NEGATIVE will be marked with a MINUS (-) sign. There may also be a BLACK plastic protective cover over the negative battery post. Jumper cables have designated colors, RED for POSITIVE (+) and BLACK for NEGATIVE (-). DO NOT allow the metal ends to touch together, this may harm the battery, charging system and/or electronics in the vehicle. 1. Press on the power button on jump starter once. Ensure that the power level gauge is 3 lights or more. 2. Take the BLACK end of the jumper cord and plug it into the power bank jump start socket which is found underneath the grey cover. 3. Fasten the RED jumper cord to the POSITIVE (+) post on the car battery. The POSITIVE battery post will be slightly bigger than the NEGATIVE post, and will be marked with a PLUS

(+) sign. There may also be a RED plastic protective cover over the positive battery post. NOTE: Do not attach the red clamp (+) and the black clamp (-) at the same time. CAUTION: DO NOT lean directly over the battery while making jumper connections. 5. Check the LED status on the indicator box found on the BLACK jumper cable. Unless the light is flashing RED, proceed to the next step. Please refer to the LED status chart found on the next page if necessary. 6. You now have 30 seconds to start your vehicle. If it does not crank or cranks very slowly, secure the jumper connections to make sure there is a good contact on battery posts of the vehicle. Then try again. The engine should start if there are no other issues (such as a bad starter or ignition circuit issues). Do not attempt to jump start the vehicle more than 3 times from the jump starter. If the vehicle fails to start then it is likely that there is another issue. 7. Please detach the jumper cables from the vehicle within 30 seconds. TO USE A FLASHLIGHT Press the power button for 3 seconds to start the LED illumination. You can then select from 2 modes

(On/SOS) by pressing the power button lightly in sequence. 7 I G N T R A T S P M U J Remove the RED/POSTIVE end first and then the BLACK/NEGATIVE clamp. Do not allow the metal ends of the jumper cables to touch each other or the RED cables to touch anything metal on the car. Now unplug the BLUE end of the jumper cable from the power bank.This will reset the jumper cable. In 10 seconds the power bank will power off automatically. 8. Keep the engine running 20 to 30 minutes, or drive the car to recharge the battery. NOTE: If the engine dies shortly after it has been jump started, or as soon as the jumper cables are disconnected, it probably means the vehicle charging system is not working (bad alternator, voltage regulator, wiring problem or loose/dirty battery cables). Please mechanic or vehicles manufacture for assistance. POLARITY PROTECTION CIRCUIT STATUS Status (Light & Sound Indicator) Red Light Green Light Sound None None On Flashing Off Mode The car battery is ready for jump start. The Power Bank needs to be charged. 8 R E G R A H C S S E L E R W I model no. ENJ1000 | contact us 1-866-295-6775 This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the device. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canadas licence-exempt RSS(s). Operation is subject to the following two conditions:

(1) This device may not cause interference.

(2) This device must accept any interference, including interference that may cause undesired operation of the device. Lmetteur/rcepteur exempt de licence contenu dans le prsent appareil est conforme aux CNR dInnovation, Sciences et Dveloppement conomique Canada applicables aux appareils radio exempts de licence. Lexploitation est autorise aux deux conditions suivantes :

1) Lappareil ne doit pas produire de brouillage;

2) Lappareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible den compromettre le fonctionnement. S N R U T E R D N A Y T N A R R A W 9 model no. ENJ1000 | contact us 1-866-295-6775 WARRANTY AND RETURNS IF ANY PARTS ARE MISSING OR DAMAGED, OR IF YOU HAVE ANY QUESTIONS, PLEASE CALL OUR TOLL-FREE HELPLINE AT 1-866-295-6775 Read and understand this instruction manual thoroughly before using the product. It contains important information for your safety as well as operating and maintenance advice. Keep this instruction manual for future use. Should this product be passed on to a third party, this instruction manual must be included. The English version of this manual is available online at:

www.energizerpower.com Bright Manufacturing LLC and/or its affiliates are not responsible for a user's intended or actual use of the car jump starter. In no event shall Bright Manufacturing LLC and/or its affiliates have any liability for any losses

(whether direct or indirect, in contract, tort or otherwise) incurred in connection with the car jump starter, including but not limited to damaged property, personal injury and/or loss of life. Neither shall Bright Manufacturing LLC and/or its affiliates have any liability for any decision, action taken based on relying on the stability or performance of the car jump starter. Bright Manufacturing LLC and/or its affiliates, the manufacturer, distributor and seller shall not be liable for any injury, loss or dam age, incidental or consequential, arising out of the use or intended use of the product. This Energizer jump starter product carries a one (1) year warranty against defects in workmanship and materials. At its discretion, Bright Manufacturing agrees to have any defective part(s) repaired or replaced free of charge, within the stated warranty period, when returned by the original purchaser with proof of purchase. This product is not guaranteed against wear or breakage due to misuse and/or abuse. 4010229 Bright Manufacturing LLC and/or its affiliates, the manufacturer, distributor and seller shall not be liable for any injury, loss or damage, incidental or consequential, arising out of the use or intended use of the product. MADE IN CHINA IMPORTED BY BRIGHT MANUFACTURING LLC, FORT LAUDERDALE, FL 10 S E T O N

DMARREUR + CHARGEUR SANS FIL JUMP STARTER WIRELESS CHARGER 12V CAR JUMP STARTER &

PORTABLE POWER BANK WITH WIRELESS CHARGING 4010229 INSTRUCTI ON MANUAL model no. ENX1000 IMPORTANT:

Please read this manual carefully before operating this jum I N O T A M R O F N I Y T E F A S 2 WARNING model no. ENX1000 | contact us 1-866-295-6775 Always wear safety glasses when jump starting a battery, and gloves when handling a battery. When jump starting a vehicle please ensure that the clamp connection is securely fitted into the jump starter socket. Ensure the battery clamps are connected correctly, and the connectors are free from rust and dirt. Do not allow this product to become wet. Do not immerse the product in water. Do not operate the product in explosive atmospheres, such as in the presence of flammable liquid, gas or dust. Do not modify or disassemble this product. Do not store in locations where the temperature may exceed 140F (60C). Charge only using the charger provided. Under extreme heat conditions, battery leakage may occur. Avoid contact with your skin. In case of skin or eye contact, rinse immediately with clean water and seek medical attention. BATTERY DISPOSAL The battery is self-contained and not consumer replaceable. The battery must be disposed of properly when it no longer holds a charge. Proper charging practices will increase the life of the product. For Information on battery recycling, call toll-free 800-822-8837. For information regarding air travel safety with batteries please reference this website by the U.S. Department of Transportation:

http://phmsa.dot.gov/safetravel/batteries NOTE: This Car jump starter and portable power bank contains the equivalent of 2.4g of lithium and gives 26.7 watt hours of power. PROP 65 WARNING This product contains lead, a chemical known to the state of California to cause cancer, birth defects or other reproductive harm. TO CHARGE YOUR JUMP STARTER At home:

1. Plug the AC Power Adaptor into any 120V outlet. 2. Attach the DC plug into the USB-C port on the Power Bank with the equipped USB-A to USB-C cable In the Car:

1. Plug the car adaptor into the socket of cigarette lighter. 2. Attach the DC plug into the USB-C port on the Power Bank with the equipped USB-A to USB-C cable. 3 I G N G R A H C TO POWER YOUR MOBILE DEVICES Use the original manufacturer's USB cable that came with your device and plug it into the USB output ports. The USB charging port can charge at 5V/2A, 9V/2A or 12V/2A compatible Quick Charge technology devices or charges nonQuick Charge devices at up to 2.4A. Once you charge your device, the power level gauge will show the battery level. To check the power capacity again, simply press the power button once. TO CHARGE USING WIRELESS CHARGING SURFACE Make sure your device is Qi-compatible. If the case is metal, remove prior to charging. If you are having issues charging, remove your case and try again. Place the Qi-

compatible device directly onto the indicated wireless charging icon. Your device will display the charging progress. Charging time will depend on the type of device. Do not place magnetic cards or similar items near this product. Place the unit on a sturdy and flat surface during charging. Keep the unit out of reach of children 4 S T N E T N O C E G A K C A P model no. ENX1000 | contact us 1-866-295-6775 Portable charger/wireless 4 Jumper cable PACKAGE CONTENTS 1 2 3 charger USB-A to USB-C cable Car DC charger 2 J UM P S TAR TE R WI RE LE SS DM ARRE CHARG E R UR

+ CHARG E UR S ANS FI L 1 4 3 PRODUCT SPECIFICATION Product Dimensions: 5.35 x 2.99 x 0.98 inch (136 x 76 x 25 mm) Product Weight: 0.68 lbs (310g) Multi-function Jump Starter Dmarreur Batterie Multi-

fonction Cap.: 7,200mAh Input (TypeC): 5V/2.4A, 9V/2A Output: QC3.0 Temp: -13F to 104F / -25C to 40C Start Current:

16V/500A Peak Current: 16V/1000A USB: QC3.0, 5V/2A, 9V/2A, 12V/2A E Battery level indicator F Wireless charging surface G Battery clamps with cross polarity protection 5 I I I S N O T A C F C E P S T C U D O R P FUNCTIONALITIES A Power & LED light button B USB output port C Jumpstarter connection port 9V/2A D Input (TypeC): 5V/2.4A, F A B C D G E POWER LEVEL GAUGE LIGHTS Press the power button to check the capacity of the Power Bank Indicator Lights 1 Flashing 1 Solid 2 Solid 3 Solid 4 Solid Battery Capacity Below 5%

5-25%

26-50%

51-75%

76%-full When charging, the indicator gauge will light up one by one. The number of stable lights show the battery capacity. When all the indicator lights are firm, then the Power Bank is fully topped up. I G N T R A T S P M U J 6 model no. ENX1000 | contact us 1-866-295-6775 IN ORDER TO JUMP START THE AUTOMOBILE BATTERY, FOLLOW THESE INSTRUCTIONS 4. Fasten the BLACK jumper cable to the NEGATIVE (-) post on the car battery.The NEGATIVE will be marked with a MINUS (-) sign. There may also be a BLACK plastic protective cover over the negative battery post. Jumper cables have designated colors, RED for POSITIVE (+) and BLACK for NEGATIVE (-). DO NOT allow the metal ends to touch together, this may harm the battery, charging system and/or electronics in the vehicle. 1. Press on the power button on jump starter once. Ensure that the power level gauge is 3 lights or more. 2. Take the BLACK end of the jumper cord and plug it into the power bank jump start socket which is found underneath the grey cover. 3. Fasten the RED jumper cord to the POSITIVE (+) post on the car battery. The POSITIVE battery post will be slightly bigger than the NEGATIVE post, and will be marked with a PLUS

(+) sign. There may also be a RED plastic protective cover over the positive battery post. NOTE: Do not attach the red clamp (+) and the black clamp (-) at the same time. CAUTION: DO NOT lean directly over the battery while making jumper connections. 5. Check the LED status on the indicator box found on the BLACK jumper cable. Unless the light is flashing RED, proceed to the next step. Please refer to the LED status chart found on the next page if necessary. 6. You now have 30 seconds to start your vehicle. If it does not crank or cranks very slowly, secure the jumper connections to make sure there is a good contact on battery posts of the vehicle. Then try again. The engine should start if there are no other issues (such as a bad starter or ignition circuit issues). Do not attempt to jump start the vehicle more than 3 times from the jump starter. If the vehicle fails to start then it is likely that there is another issue. 7. Please detach the jumper cables from the vehicle within 30 seconds. TO USE A FLASHLIGHT Press the power button for 3 seconds to start the LED illumination. You can then select from 2 modes

(On/SOS) by pressing the power button lightly in sequence. 7 I G N T R A T S P M U J Remove the RED/POSTIVE end first and then the BLACK/NEGATIVE clamp. Do not allow the metal ends of the jumper cables to touch each other or the RED cables to touch anything metal on the car. Now unplug the BLUE end of the jumper cable from the power bank.This will reset the jumper cable. In 10 seconds the power bank will power off automatically. 8. Keep the engine running 20 to 30 minutes, or drive the car to recharge the battery. NOTE: If the engine dies shortly after it has been jump started, or as soon as the jumper cables are disconnected, it probably means the vehicle charging system is not working (bad alternator, voltage regulator, wiring problem or loose/dirty battery cables). Please mechanic or vehicles manufacture for assistance. POLARITY PROTECTION CIRCUIT STATUS Status (Light & Sound Indicator) Red Light Green Light d Soun None The car battery is ready for jump start. The Power Bank needs to be charged. None Mod e On Flashing Off 8 R E G R A H C S S E L E R W I model no. ENX1000 | contact us 1-866-295-6775 This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the device. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canadas licence-exempt RSS(s). Operation is subject to the following two conditions:

(1) This device may not cause interference.

(2) This device must accept any interference, including interference that may cause undesired operation of the device. Lmetteur/rcepteur exempt de licence contenu dans le prsent appareil est conforme aux CNR dInnovation, Sciences et Dveloppement conomique Canada applicables aux appareils radio exempts de licence. Lexploitation est autorise aux deux conditions suivantes :

1) Lappareil ne doit pas produire de brouillage;

2) Lappareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible den compromettre le fonctionnement. S N R U T E R D N A Y T N A R R A W 9 model no. ENX1000 | contact us 1-866-295-6775 WARRANTY AND RETURNS IF ANY PARTS ARE MISSING OR DAMAGED, OR IF YOU HAVE ANY QUESTIONS, PLEASE CALL OUR TOLL-FREE HELPLINE AT 1-866-295-6775 Read and understand this instruction manual thoroughly before using the product. It contains important information for your safety as well as operating and maintenance advice. Keep this instruction manual for future use. Should this product be passed on to a third party, this instruction manual must be included. The English version of this manual is available online at:

www.energizerpower.com Bright Manufacturing LLC and/or its affiliates are not responsible for a user's intended or actual use of the car jump starter. In no event shall Bright Manufacturing LLC and/or its affiliates have any liability for any losses

(whether direct or indirect, in contract, tort or otherwise) incurred in connection with the car jump starter, including but not limited to damaged property, personal injury and/or loss of life. Neither shall Bright Manufacturi ng LLC and/or its affiliates have any liability for any decision, action taken based on relying on the stability or performance of the car jump starter. Bright Manufacturing LLC and/or its affiliates, the manufacturer, distributor and seller shall not be liable for any injury, loss or damage, incidental or consequential, arising out of the use or intended use of the product. This Energizer jump starter product carries a one (1) year warranty against defects in workmanship and materials. At its discretion, Bright Manufacturing agrees to have any defective part(s) repaired or replaced free of charge, within the stated warranty period, when returned by the original purchaser with proof of purchase. This product is not guaranteed against wear or breakage due to misuse and/or abuse. 4010229 Bright Manufacturing LLC and/or its affiliates, the manufacturer, distributor and seller shall not be liable for any injury, loss or damage, incidental or consequential, arising out of the use or intended use of the product. MADE IN CHINA IMPORTED BY BRIGHT MANUFACTURING LLC, FORT LAUDERDALE, FL 10 S E T O N

JUMP STARTER + WIRELESS CHARGER 12V CAR JUMP STARTER &

PORTABLE POWER BANK WITH WIRELESS CHARGING 4010229 INSTRUCTI ON MANUAL model no. KRJ1000 IMPORTANT:

Please read this manual carefully before operating this jum I N O T A M R O F N I Y T E F A S 2 WARNING model no. KRJ1000 | contact us 1-866-295-6775 Always wear safety glasses when jump starting a battery, and gloves when handling a battery. When jump starting a vehicle please ensure that the clamp connection is securely fitted into the jump starter socket. Ensure the battery clamps are connected correctly, and the connectors are free from rust and dirt. Do not allow this product to become wet. Do not immerse the product in water. Do not operate the product in explosive atmospheres, such as in the presence of flammable liquid, gas or dust. Do not modify or disassemble this product. Do not store in locations where the temperature may exceed 140F (60C). Charge only using the charger provided. Under extreme heat conditions, battery leakage may occur. Avoid contact with your skin. In case of skin or eye contact, rinse immediately with clean water and seek medical attention. BATTERY DISPOSAL The battery is self-contained and not consumer replaceable. The battery must be disposed of properly when it no longer holds a charge. Proper charging practices will increase the life of the product. For Information on battery recycling, call toll-free 800-822-8837. For information regarding air travel safety with batteries please reference this website by the U.S. Department of Transportation:

http://phmsa.dot.gov/safetravel/batteries NOTE: This Car jump starter and portable power bank contains the equivalent of 2.4g of lithium and gives 26.7 watt hours of power. PROP 65 WARNING This product contains lead, a chemical known to the state of California to cause cancer, birth defects or other reproductive harm. TO CHARGE YOUR JUMP STARTER At home:

1. Plug the AC Power Adaptor into any 120V outlet. 2. Attach the DC plug into the USB-C port on the Power Bank with the equipped USB-A to USB-C cable In the Car:

1. Plug the car adaptor into the socket of cigarette lighter. 2. Attach the DC plug into the USB-C port on the Power Bank with the equipped USB-A to USB-C cable. 3 I G N G R A H C TO POWER YOUR MOBILE DEVICES Use the original manufacturer's USB cable that came with your device and plug it into the USB output ports. The USB charging port can charge at 5V/2A, 9V/2A or 12V/2A compatible Quick Charge technology devices or charges nonQuick Charge devices at up to 2.4A. Once you charge your device, the power level gauge will show the battery level. To check the power capacity again, simply press the power button once. TO CHARGE USING WIRELESS CHARGING SURFACE Make sure your device is Qi-compatible. If the case is metal, remove prior to charging. If you are having issues charging, remove your case and try again. Place the Qi-

compatible device directly onto the indicated wireless charging icon. Your device will display the charging progress. Charging time will depend on the type of device. Do not place magnetic cards or similar items near this product. Place the unit on a sturdy and flat surface during charging. Keep the unit out of reach of children 4 S T N E T N O C E G A K C A P model no. KRJ1000 | contact us 1-866-295-6775 1 Portable charger/wireless 4 Jumper cable PACKAGE CONTENTS charger 2 USB-A to USB-C cable 3 Car DC charger 2 J UM P S TAR TE R + WI RE LE SS CHARG E R 1 4 3 PRODUCT SPECIFICATION Product Dimensions: 5.35 x 2.99 x 0.98 inch (136 x 76 x 25 mm) Product Weight: 0.68 lbs (310g) Multi-function Jump Starter Dmarreur Batterie Multi-

fonction Cap.: 7,200mAh Input (TypeC): 5V/2.4A, 9V/2A Output: QC3.0 Temp: -13F to 104F / -25C to 40C Start Current:

16V/500A Peak Current: 16V/1000A USB: QC3.0, 5V/2A, 9V/2A, 12V/2A E Battery level indicator F Wireless charging surface G Battery clamps with cross polarity protection 5 I I I S N O T A C F C E P S T C U D O R P FUNCTIONALITIES A Power & LED light button B USB output port C Jumpstarter connection port 9V/2A D Input (TypeC): 5V/2.4A, F A B C D G E POWER LEVEL GAUGE LIGHTS Press the power button to check the capacity of the Power Bank Indicator Lights 1 Flashing 1 Solid 2 Solid 3 Solid 4 Solid Battery Capacity Below 5%

5-25%

26-50%

51-75%

76%-full When charging, the indicator gauge will light up one by one. The number of stable lights show the battery capacity. When all the indicator lights are firm, then the Power Bank is fully topped up. I G N T R A T S P M U J 6 model no. KRJ1000 | contact us 1-866-295-6775 IN ORDER TO JUMP START THE AUTOMOBILE BATTERY, FOLLOW THESE INSTRUCTIONS 4. Fasten the BLACK jumper cable to the NEGATIVE (-) post on the car battery.The NEGATIVE will be marked with a MINUS (-) sign. There may also be a BLACK plastic protective cover over the negative battery post. Jumper cables have designated colors, RED for POSITIVE (+) and BLACK for NEGATIVE (-). DO NOT allow the metal ends to touch together, this may harm the battery, charging system and/or electronics in the vehicle. 1. Press on the power button on jump starter once. Ensure that the power level gauge is 3 lights or more. 2. Take the BLACK end of the jumper cord and plug it into the power bank jump start socket which is found underneath the grey cover. 3. Fasten the RED jumper cord to the POSITIVE (+) post on the car battery. The POSITIVE battery post will be slightly bigger than the NEGATIVE post, and will be marked with a PLUS

(+) sign. There may also be a RED plastic protective cover over the positive battery post. NOTE: Do not attach the red clamp (+) and the black clamp (-) at the same time. CAUTION: DO NOT lean directly over the battery while making jumper connections. 5. Check the LED status on the indicator box found on the BLACK jumper cable. Unless the light is flashing RED, proceed to the next step. Please refer to the LED status chart found on the next page if necessary. 6. You now have 30 seconds to start your vehicle. If it does not crank or cranks very slowly, secure the jumper connections to make sure there is a good contact on battery posts of the vehicle. Then try again. The engine should start if there are no other issues (such as a bad starter or ignition circuit issues). Do not attempt to jump start the vehicle more than 3 times from the jump starter. If the vehicle fails to start then it is likely that there is another issue. 7. Please detach the jumper cables from the vehicle within 30 seconds. TO USE A FLASHLIGHT Press the power button for 3 seconds to start the LED illumination. You can then select from 2 modes

(On/SOS) by pressing the power button lightly in sequence. 7 I G N T R A T S P M U J Remove the RED/POSTIVE end first and then the BLACK/NEGATIVE clamp. Do not allow the metal ends of the jumper cables to touch each other or the RED cables to touch anything metal on the car. Now unplug the BLUE end of the jumper cable from the power bank.This will reset the jumper cable. In 10 seconds the power bank will power off automatically. 8. Keep the engine running 20 to 30 minutes, or drive the car to recharge the battery. NOTE: If the engine dies shortly after it has been jump started, or as soon as the jumper cables are disconnected, it probably means the vehicle charging system is not working (bad alternator, voltage regulator, wiring problem or loose/dirty battery cables). Please mechanic or vehicles manufacture for assistance. POLARITY PROTECTION CIRCUIT STATUS Status (Light & Sound Indicator) Red Light Green Light d Soun None The car battery is ready for jump start. The Power Bank needs to be charged. None Mod e On Flashing Off 8 R E G R A H C S S E L E R W I model no. KRJ1000 | contact us 1-866-295-6775 This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the device. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canadas licence-exempt RSS(s). Operation is subject to the following two conditions:

(1) This device may not cause interference.

(2) This device must accept any interference, including interference that may cause undesired operation of the device. Lmetteur/rcepteur exempt de licence contenu dans le prsent appareil est conforme aux CNR dInnovation, Sciences et Dveloppement conomique Canada applicables aux appareils radio exempts de licence. Lexploitation est autorise aux deux conditions suivantes :

1) Lappareil ne doit pas produire de brouillage;

2) Lappareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible den compromettre le fonctionnement. S N R U T E R D N A Y T N A R R A W 9 model no. KRJ1000 | contact us 1-866-295-6775 WARRANTY AND RETURNS IF ANY PARTS ARE MISSING OR DAMAGED, OR IF YOU HAVE ANY QUESTIONS, PLEASE CALL OUR TOLL-FREE HELPLINE AT 1-866-295-6775 Read and understand this instruction manual thoroughly before using the product. It contains important information for your safety as well as operating and maintenance advice. Keep this instruction manual for future use. Should this product be passed on to a third party, this instruction manual must be included. The English version of this manual is available online at:

www.kriegermfg.com Bright Manufacturing LLC and/or its affiliates are not responsible for a user's intended or actual use of the car jump starter. In no event shall Bright Manufacturing LLC and/or its affiliates have any liability for any losses

(whether direct or indirect, in contract, tort or otherwise) incurred in connection with the car jump starter, including but not limited to damaged property, personal injury and/or loss of life. Neither shall Bright Manufacturing LLC and/or its affiliates have any liability for any decision, action taken based on relying on the stability or performance of the car jump starter. Bright Manufacturing LLC and/or its affiliates, the manufacturer, distributor and seller shall not be liable for any injury, loss or damage, incidental or consequential, arising out of the use or intended use of the product. This Krieger jump starter product carries a one (1) year warranty against defects in workmanship and materials. At its discretion, Bright Manufacturing agrees to have any defective part(s) repaired or replaced free of charge, within the stated warranty period, when returned by the original purchaser with proof of purchase. This product is not guaranteed against wear or breakage due to misuse and/or abuse. 4010229 Bright Manufacturing LLC and/or its affiliates, the manufacturer, distributor and seller shall not be liable for any injury, loss or damage, incidental or consequential, arising out of the use or intended use of the product. MADE IN CHINA IMPORTED BY BRIGHT MANUFACTURING LLC, FORT LAUDERDALE, FL 10 S E T O N

JUMP STARTER + WIRELESS CHARGER 12V CAR JUMP STARTER &

PORTABLE POWER BANK WITH WIRELESS CHARGING 4010229 INSTRUCTI ON MANUAL model no. KRX1000 IMPORTANT:

Please read this manual carefully before operating this jum I N O T A M R O F N I Y T E F A S 2 WARNING model no. KRX1000 | contact us 1-866-295-6775 Always wear safety glasses when jump starting a battery, and gloves when handling a battery. When jump starting a vehicle please ensure that the clamp connection is securely fitted into the jump starter socket. Ensure the battery clamps are connected correctly, and the connectors are free from rust and dirt. Do not allow this product to become wet. Do not immerse the product in water. Do not operate the product in explosive atmospheres, such as in the presence of flammable liquid, gas or dust. Do not modify or disassemble this product. Do not store in locations where the temperature may exceed 140F (60C). Charge only using the charger provided. Under extreme heat conditions, battery leakage may occur. Avoid contact with your skin. In case of skin or eye contact, rinse immediately with clean water and seek medical attention. BATTERY DISPOSAL The battery is self-contained and not consumer replaceable. The battery must be disposed of properly when it no longer holds a charge. Proper charging practices will increase the life of the product. For Information on battery recycling, call toll-free 800-822-8837. For information regarding air travel safety with batteries please reference this website by the U.S. Department of Transportation:

http://phmsa.dot.gov/safetravel/batteries NOTE: This Car jump starter and portable power bank contains the equivalent of 2.4g of lithium and gives 26.7 watt hours of power. PROP 65 WARNING This product contains lead, a chemical known to the state of California to cause cancer, birth defects or other reproductive harm. TO CHARGE YOUR JUMP STARTER At home:

1. Plug the AC Power Adaptor into any 120V outlet. 2. Attach the DC plug into the USB-C port on the Power Bank with the equipped USB-A to USB-C cable In the Car:

1. Plug the car adaptor into the socket of cigarette lighter. 2. Attach the DC plug into the USB-C port on the Power Bank with the equipped USB-A to USB-C cable. 3 I G N G R A H C TO POWER YOUR MOBILE DEVICES Use the original manufacturer's USB cable that came with your device and plug it into the USB output ports. The USB charging port can charge at 5V/2A, 9V/2A or 12V/2A compatible Quick Charge technology devices or charges nonQuick Charge devices at up to 2.4A. Once you charge your device, the power level gauge will show the battery level. To check the power capacity again, simply press the power button once. TO CHARGE USING WIRELESS CHARGING SURFACE Make sure your device is Qi-compatible. If the case is metal, remove prior to charging. If you are having issues charging, remove your case and try again. Place the Qi-

compatible device directly onto the indicated wireless charging icon. Your device will display the charging progress. Charging time will depend on the type of device. Do not place magnetic cards or similar items near this product. Place the unit on a sturdy and flat surface during charging. Keep the unit out of reach of children 4 S T N E T N O C E G A K C A P model no. KRX1000 | contact us 1-866-295-6775 Portable charger/wireless 4 Jumper cable PACKAGE CONTENTS 1 2 3 charger USB-A to USB-C cable Car DC charger 2 JUMP STARTER + WIRELESS CHARGER 1 4 3 PRODUCT SPECIFICATION Product Dimensions: 5.35 x 2.99 x 0.98 inch (136 x 76 x 25 mm) Product Weight: 0.68 lbs (310g) Multi-function Jump Starter Dmarreur Batterie Multi-

fonction Cap.: 7,200mAh Input (TypeC): 5V/2.4A, 9V/2A Output: QC3.0 Temp: -13F to 104F / -25C to 40C Start Current:

16V/500A Peak Current: 16V/1000A USB: QC3.0, 5V/2A, 9V/2A, 12V/2A E Battery level indicator F Wireless charging surface G Battery clamps with cross polarity protection 5 I I I S N O T A C F C E P S T C U D O R P FUNCTIONALITIES A Power & LED light button B USB output port C Jumpstarter connection port 9V/2A D Input (TypeC): 5V/2.4A, F A B C D G E POWER LEVEL GAUGE LIGHTS Press the power button to check the capacity of the Power Bank Indicator Lights 1 Flashing 1 Solid 2 Solid 3 Solid 4 Solid Battery Capacity Below 5%

5-25%

26-50%

51-75%

76%-full When charging, the indicator gauge will light up one by one. The number of stable lights show the battery capacity. When all the indicator lights are firm, then the Power Bank is fully topped up. I G N T R A T S P M U J 6 model no. KRX1000 | contact us 1-866-295-6775 IN ORDER TO JUMP START THE AUTOMOBILE BATTERY, FOLLOW THESE INSTRUCTIONS 4. Fasten the BLACK jumper cable to the NEGATIVE (-) post on the car battery.The NEGATIVE will be marked with a MINUS (-) sign. There may also be a BLACK plastic protective cover over the negative battery post. Jumper cables have designated colors, RED for POSITIVE (+) and BLACK for NEGATIVE (-). DO NOT allow the metal ends to touch together, this may harm the battery, charging system and/or electronics in the vehicle. 1. Press on the power button on jump starter once. Ensure that the power level gauge is 3 lights or more. 2. Take the BLACK end of the jumper cord and plug it into the power bank jump start socket which is found underneath the grey cover. 3. Fasten the RED jumper cord to the POSITIVE (+) post on the car battery. The POSITIVE battery post will be slightly bigger than the NEGATIVE post, and will be marked with a PLUS

(+) sign. There may also be a RED plastic protective cover over the positive battery post. NOTE: Do not attach the red clamp (+) and the black clamp (-) at the same time. CAUTION: DO NOT lean directly over the battery while making jumper connections. 5. Check the LED status on the indicator box found on the BLACK jumper cable. Unless the light is flashing RED, proceed to the next step. Please refer to the LED status chart found on the next page if necessary. 6. You now have 30 seconds to start your vehicle. If it does not crank or cranks very slowly, secure the jumper connections to make sure there is a good contact on battery posts of the vehicle. Then try again. The engine should start if there are no other issues (such as a bad starter or ignition circuit issues). Do not attempt to jump start the vehicle more than 3 times from the jump starter. If the vehicle fails to start then it is likely that there is another issue. 7. Please detach the jumper cables from the vehicle within 30 seconds. TO USE A FLASHLIGHT Press the power button for 3 seconds to start the LED illumination. You can then select from 2 modes

(On/SOS) by pressing the power button lightly in sequence. 7 I G N T R A T S P M U J Remove the RED/POSTIVE end first and then the BLACK/NEGATIVE clamp. Do not allow the metal ends of the jumper cables to touch each other or the RED cables to touch anything metal on the car. Now unplug the BLUE end of the jumper cable from the power bank.This will reset the jumper cable. In 10 seconds the power bank will power off automatically. 8. Keep the engine running 20 to 30 minutes, or drive the car to recharge the battery. NOTE: If the engine dies shortly after it has been jump started, or as soon as the jumper cables are disconnected, it probably means the vehicle charging system is not working (bad alternator, voltage regulator, wiring problem or loose/dirty battery cables). Please mechanic or vehicles manufacture for assistance. POLARITY PROTECTION CIRCUIT STATUS Status (Light & Sound Indicator) Red Light Green Light d Soun None The car battery is ready for jump start. The Power Bank needs to be charged. None Mod e On Flashing Off 8 R E G R A H C S S E L E R W I model no. KRX1000 | contact us 1-866-295-6775 This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the device. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canadas licence-exempt RSS(s). Operation is subject to the following two conditions:

(1) This device may not cause interference.

(2) This device must accept any interference, including interference that may cause undesired operation of the device. Lmetteur/rcepteur exempt de licence contenu dans le prsent appareil est conforme aux CNR dInnovation, Sciences et Dveloppement conomique Canada applicables aux appareils radio exempts de licence. Lexploitation est autorise aux deux conditions suivantes :

1) Lappareil ne doit pas produire de brouillage;

2) Lappareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible den compromettre le fonctionnement. S N R U T E R D N A Y T N A R R A W 9 model no. KRX1000 | contact us 1-866-295-6775 WARRANTY AND RETURNS IF ANY PARTS ARE MISSING OR DAMAGED, OR IF YOU HAVE ANY QUESTIONS, PLEASE CALL OUR TOLL-FREE HELPLINE AT 1-866-295-6775 Read and understand this instruction manual thoroughly before using the product. It contains important information for your safety as well as operating and maintenance advice. Keep this instruction manual for future use. Should this product be passed on to a third party, this instruction manual must be included. The English version of this manual is available online at:

www.kriegermfg.com Bright Manufacturing LLC and/or its affiliates are not responsible for a user's intended or actual use of the car jump starter. In no event shall Bright Manufacturing LLC and/or its affiliates have any liability for any losses

(whether direct or indirect, in contract, tort or otherwise) incurred in connection with the car jump starter, including but not limited to damaged property, personal injury and/or loss of life. Neither shall Bright Manuf acturing LLC and/or its affiliates have any liability for any decision, action taken based on relying on the stability or performance of the car jump starter. Bright Manufacturing LLC and/or its affiliates, the manufacturer, distributor and seller shall not be liable for any injury, loss or damage, incidental or consequential, arising out of the use or intended use of the product. This Krieger jump starter product carries a one (1) year warranty against defects in workmanship and materials. At its discretion, Bright Manufacturing agrees to have any defective part(s) repaired or replaced free of charge, within the stated warranty period, when returned by the original purchaser with proof of purchase. This product is not guaranteed against wear or breakage due to misuse and/or abuse. 4010229 Bright Manufacturing LLC and/or its affiliates, the manufacturer, distributor and seller shall not be liable for any injury, loss or damage, incidental or consequential, arising out of the use or intended use of the product. MADE IN CHINA IMPORTED BY BRIGHT MANUFACTURING LLC, FORT LAUDERDALE, FL 10 S E T O N

ISO VIEW Model/Modle: ENJ1000 Multi-function Jump Starter Dmarreur Batterie Multi-fonction 12V/100A (5s) Cap.: 7,200mAh Input/Entre (TypeC): 5V/2.4A, 9V/2A

, Output/Sortie: QC3.0 Wireless charger10W. Max Temp: 10C Wireless charger 45C 12V/100A (5s) USB: QC3.0, 5V/2A, 9V/2A, 12V/2A Pousse: 12V/1000A(1ms) Boost: 12V/1000A (1ms) to/

CAUTION / MISE EN GA This device is not intended for use in a commercial repair factory. This device is intended to be stored indoors when not in use. This device is intended for temporary use outdoors and reasonable care should be exercised when using the device in wet conditions. Risk of injury to persons. Do not use this product if the battery cables are damaged in any way. Le dispositif n'est pas destin tre utilis dans un atelier de rparation commerciale. Le dispositif est destin tre rang l'intrieur lorsqu'ils n'est pas utilise. Le dispositif ne doit pas tre range ou laiss l'extrieur lorsqu'il n'est pas utilis. Le dispositf est destin une utilization l'extrieur temporaire et il faut faire prevue d'une prudence raisonnable lorsqu'il est utilis dans des conditions humides. Risque de blessures aux personnes. Ne pas utiliser ce produit si le cordon d'alimentation ou les cbles de batterie sont endommags de quelque facon. WARNING / ATTENTION Do not ocercharge the internal battery. See instruction manual. Do not smoke, strike a match, or cause a spark in the vicinity of the power pack. Only charge the internal battery in a well ventillated area. Ne pas surchargez la batterie interne. Consulter le manuel d'instructions. II ne faut pas fumer, allumer une allumette ou produire des tincelle proximit du bloc d'alimentation. Charger la batterie uniquement dans un endroit bien ar. FCC ID: 2AXD6-JS1000 and IC: 26426-JS1000 This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. MFG DATE MM/YY Made in China Fabriqu en Chine SERVICE CERTIFIED TO ANSI/CAN/UL STD.2743 2020 Energizer. Energizer and certain graphic designs are trademarks of Energizer Brands, LLC and related subsidiaries and are used under license by Bright Manufacturing LLC. 2020 Energizer. Energizer et certains graphiques sont des marques de commerce de Energizer Brands, LLC et ses filiales associs et sont utilises sous licence par Bright Manufacturing LLC. Energizer Jump Starter bottom side 07/17/20 LZ

This drawing is the proprietary and confidential property of Powerbright Electric Corporation. Dissemination of this document or the information contained herein is prohibited without the express permission of the Director of Engineering. Use of this document by any supplier or distributor is expressly limited to the use authorized by Powerbright Electric Corporation in providing it to you. Energizer Jump Starter wireless charger

INITIAL RELEASE 07/17/20 LZ NO. ECN DATE SIG. FRACTIONAL ANGULAR UNLESS OTHERWISE SPECIFIED TOLERANCES THIRD ANGLE PROJECTI ON Powerbright SOLIDWORKS Model/Modle: ENX1000 Multi-function Jump Starter Dmarreur Batterie Multi-fonction 12V/100A (5s) Cap.: 7,200mAh Pousse: 12V/1000A (1ms) Input/Entre (TypeC): 5V/2.4A, 9V/2A

, Output/Sortie: QC3.0 Wireless charger10W. Max Temp: 10C Wireless charger 45C USB: QC3.0, 5V/2A, 9V/2A, 12V/2A Boost: 12V/1000A (1ms) 12V/100A (5s) to/

CAUTION / MISE EN GA This device is not intended for use in a commercial repair factory. This device is intended to be stored indoors when not in use. This device is intended for temporary use outdoors and reasonable care should be exercised when using the device in wet conditions. Risk of injury to persons. Do not use this product if the battery cables are damaged in any way. Le dispositif n'est pas destin tre utilis dans un atelier de rparation commerciale. Le dispositif est destin tre rang l'intrieur lorsqu'ils n'est pas utilise. Le dispositif ne doit pas tre range ou laiss l'extrieur lorsqu'il n'est pas utilis. Le dispositf est destin une utilization l'extrieur temporaire et il faut faire prevue d'une prudence raisonnable lorsqu'il est utilis dans des conditions humides. Risque de blessures aux personnes. Ne pas utiliser ce produit si le cordon d'alimentation ou les cbles de batterie sont endommags de quelque facon. WARNING / ATTENTION Do not ocercharge the internal battery. See instruction manual. Do not smoke, strike a match, or cause a spark in the vicinity of the power pack. Only charge the internal battery in a well ventillated area. Ne pas surchargez la batterie interne. Consulter le manuel d'instructions. II ne faut pas fumer, allumer une allumette ou produire des tincelle proximit du bloc d'alimentation. Charger la batterie uniquement dans un endroit bien ar. FCC ID: 2AXD6-JS1000 and IC: 26426-JS1000 This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. MFG DATE MM/YY Made in China Fabriqu en Chine SERVICE CERTIFIED TO ANSI/CAN/UL STD.2743 2020 Energizer. Energizer and certain graphic designs are trademarks of Energizer Brands, LLC and related subsidiaries and are used under license by Bright Manufacturing LLC. 2020 Energizer. Energizer et certains graphiques sont des marques de commerce de Energizer Brands, LLC et ses filiales associs et sont utilises sous licence par Bright Manufacturing LLC. ISO VIEW Energizer Jump Starter bottom side ID2 NO. Electric Corporation. Dissemination of this document or the information contained herein is prohibited without the express permission of the Director of Engineering. Use of this document by any supplier or distributor is expressly limited to the use authorized by Powerbright Electric Corporation in providing it to you. Energizer Jump Starter wireless charger ID2

07/21/20 LZ

UNLESS OTHERWISE SPECIFIED TOLERANCES THIRD ANGLE PROJECTI ON Powerbright SOLIDWORKS INITIAL RELEASE 07/21/20 LZ ECN DATE SIG. FRACTIONAL ANGULAR ISO VIEW Model/Modle: KRJ1000 Multi-function Jump Starter Dmarreur Batterie Multi-fonction 12V/100A (5s) Cap.: 7,200mAh Input/Entre (TypeC): 5V/2.4A, 9V/2A

, Output/Sortie: QC3.0 Wireless charger10W. Max Temp: 10C Wireless charger 45C 12V/100A (5s) USB: QC3.0, 5V/2A, 9V/2A, 12V/2A Pousse: 12V/1000A (1ms) Boost: 12V/1000A (1ms) to/

CAUTION / MISE EN GA This device is not intended for use in a commercial repair factory. This device is intended to be stored indoors when not in use. This device is intended for temporary use outdoors and reasonable care should be exercised when using the device in wet conditions. Risk of injury to persons. Do not use this product if the battery cables are damaged in any way. Le dispositif n'est pas destin tre utilis dans un atelier de rparation commerciale. Le dispositif est destin tre rang l'intrieur lorsqu'ils n'est pas utilise. Le dispositif ne doit pas tre range ou laiss l'extrieur lorsqu'il n'est pas utilis. Le dispositf est destin une utilization l'extrieur temporaire et il faut faire prevue d'une prudence raisonnable lorsqu'il est utilis dans des conditions humides. Risque de blessures aux personnes. Ne pas utiliser ce produit si le cordon d'alimentation ou les cbles de batterie sont endommags de quelque facon. WARNING / ATTENTION Do not ocercharge the internal battery. See instruction manual. Do not smoke, strike a match, or cause a spark in the vicinity of the power pack. Only charge the internal battery in a well ventillated area. Ne pas surchargez la batterie interne. Consulter le manuel d'instructions. II ne faut pas fumer, allumer une allumette ou produire des tincelle proximit du bloc d'alimentation. Charger la batterie uniquement dans un endroit bien ar. FCC ID: 2AXD6-JS1000 and IC: 26426-JS1000 This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. MFG DATE MM/YY Made in China Fabriqu en Chine SERVICE CERTIFIED TO ANSI/CAN/UL STD.2743 2020 Kriger. Kriger and certain graphic designs are trademarks of Bright Manufacturing, LLC. 2020 Kriger. commerce de Bright Manufacturing, LLC. Kriger et certains graphiques sont des marques de Energizer Jump Starter bottom side NO. 07/17/20 LZ

This drawing is the proprietary and confidential property of Powerbright Electric Corporation. Dissemination of this document or the information contained herein is prohibited without the express permission of the Director of Engineering. Use of this document by any supplier or distributor is expressly limited to the use authorized by Powerbright Electric Corporation in providing it to you. Energizer Jump Starter wireless charger

INITIAL RELEASE 07/17/20 LZ ECN DATE SIG. FRACTIONAL ANGULAR UNLESS OTHERWISE SPECIFIED TOLERANCES THIRD ANGLE PROJECTI ON Powerbright SOLIDWORKS Model/Modle: KRX1000 Multi-function Jump Starter Dmarreur Batterie Multi-fonction 12V/100A (5s) Cap.: 7,200mAh Input/Entre (TypeC): 5V/2.4A, 9V/2A

, Output/Sortie: QC3.0 Wireless charger10W. Max Temp: 10C Wireless charger 45C 12V/100A (5s) USB: QC3.0, 5V/2A, 9V/2A, 12V/2A Pousse: 12V/1000A (1ms) Boost: 12V/1000A (1ms) to/

CAUTION / MISE EN GA This device is not intended for use in a commercial repair factory. This device is intended to be stored indoors when not in use. This device is intended for temporary use outdoors and reasonable care should be exercised when using the device in wet conditions. Risk of injury to persons. Do not use this product if the battery cables are damaged in any way. Le dispositif n'est pas destin tre utilis dans un atelier de rparation commerciale. Le dispositif est destin tre rang l'intrieur lorsqu'ils n'est pas utilise. Le dispositif ne doit pas tre range ou laiss l'extrieur lorsqu'il n'est pas utilis. Le dispositf est destin une utilization l'extrieur temporaire et il faut faire prevue d'une prudence raisonnable lorsqu'il est utilis dans des conditions humides. Risque de blessures aux personnes. Ne pas utiliser ce produit si le cordon d'alimentation ou les cbles de batterie sont endommags de quelque facon. WARNING / ATTENTION Do not ocercharge the internal battery. See instruction manual. Do not smoke, strike a match, or cause a spark in the vicinity of the power pack. Only charge the internal battery in a well ventillated area. Ne pas surchargez la batterie interne. Consulter le manuel d'instructions. II ne faut pas fumer, allumer une allumette ou produire des tincelle proximit du bloc d'alimentation. Charger la batterie uniquement dans un endroit bien ar. FCC ID: 2AXD6-JS1000 and IC: 26426-JS1000 This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. MFG DATE MM/YY Made in China Fabriqu en Chine SERVICE CERTIFIED TO ANSI/CAN/UL STD.2743 2020 Kriger. Kriger and certain graphic designs are trademarks of Bright Manufacturing, LLC. 2020 Kriger. commerce de Bright Manufacturing, LLC. Kriger et certains graphiques sont des marques de ISO VIEW Energizer Jump Starter bottom side ID2 NO. Electric Corporation. Dissemination of this document or the information contained herein is prohibited without the express permission of the Director of Engineering. Use of this document by any supplier or distributor is expressly limited to the use authorized by Powerbright Electric Corporation in providing it to you. Energizer Jump Starter wireless charger ID2

07/21/20 LZ

UNLESS OTHERWISE SPECIFIED TOLERANCES THIRD ANGLE PROJECTI ON Powerbright SOLIDWORKS INITIAL RELEASE 07/21/20 LZ ECN DATE SIG. FRACTIONAL ANGULAR

uaa SS SRT FZ ek

~ FOUR AAP ER tw POWER SOL HT ONE Power Bright (SIP) Ltd Authority to Act as Agent Date: November 11, 2020 American Certification Body, Inc. 6731 Whittier Avenue Suite C110 McLean, VA 22101 To Whom It May Concern:

Intertek Testing Services Shanghai is authorized to act on our behalf, until otherwise notified, for applications to American Certification Body, Inc. (ACB). We certify that we are not subject to denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 862. Further, no party, as defined in 47 CFR 1.2002 (b), to the application is subject to denial of federal benefits, that includes FCC benefits. We also declare that the information provided to the FCC is true and correct to the best of our knowledge (47 CFR 2.911(d)) and we have been informed of the grantee responsibilities (47 CFR 2.909) with regard to certified equipment. Thank you, By: Jacky Sun

(Print name) Title: General Manager On behalf of: _ Power Bright (SIP) Ltd.

(Company Name) Telephone: +86-512-62872 133-808 1 _ Must be signed by applicant contact given for applicant on the FCC site, or by the authorized agent if an appropriate authorized agent letter has been provided. Letters should be placed on appropmiate letterhead.

S TOUR EAGER AH POWTER BOL ETIO NEG Power Bright (SIP) Ltd Request for Confidentiality Date: November 11, 2020 Subject: Confidentiality Request for: FCC ID: 2AXD6-JS1000 Pursuant to FCC 47 CFR 0.457(d) and 0.459, the applicant requests that a part of the subject FCC application be held confidential. Type of Confidentiality Requested Exhibit LC] Short Term X] Permanent Block Diagrams 0) Short Term External Photos . 0 Short Term 0 Permanent *! Internal Photos OO Short Term & Permanent Operation Description/Theory of Operation CO) Short Term C Permanent Parts List & Placement/BOM CO) Short Term CO Permanent Tune-Up Procedure C Short Term Permanent Schematics C Short Term Test Setup Photos CO Short Term OO Permanent *3 Users Manual Power Bright (SIP) Ltd. __has spent substantial effort in developing this product and it is one of the first of its kind in industry. Having the subject information easily available to "competition" would negate the advantage they have achieved by developing this product. Not protecting the details of the design will result in financial hardship. Permanent Confidentiality:

The applicant requests the exhibits listed above as permanently confidential be permanently withheld from public review due to materials that contain trade secrets and proprietary information not customarily released to the public. Short-Term Confidentiality:

The applicant requests the exhibits selected above as short term confidential be withheld from public view for a period of __ (specify number of days not to exceed 180) __ days from the date of the Grant of Equipment Authorization and prior to marketing. This is to avoid premature release of sensitive information prior to marketing or release of the product to the public. Applicant is also aware that they are responsible to notify ACB in the event information regarding the product or the product is made available to the public before the requested period has expired. ACB will then release the documents listed above for public disclosure pursuant to FCC Public Notice DA 04-1705. NOTE for Industry Canada Applications:

IC currently only distinguishes Permanent Confidentiality exhibits as shown above. Short Term confidentiality is not considered applicabie to IC applications. ___Jacky Sun

(Print name) a

- The asterisked items (*) requite further information to be provided to ACB before permanent confidentiality will be extended to these exhibits. Please refer to FCC KDB 726920 and the specific Document link for DO1 found at:

https://apps. fec.gow/oetcf/kdb/forms/FTSSearchResultPage.cfm?switch=P&id=41731 and review section Il, 3) regarding specific information that must accompany these requests. 2 . Please refer to http://acbcert.com/documents/misc-docs/Memo-Short-Term-Vs-Standard-Confidentiality. pdf for complete details. 3 - Must be signed by applicant contact given for applicant on the FCC site, or by the authorized agent if an appropriate authorized agent letter has been provided. Letters should be placed on appropriate letterhead.

TREO LEACH tw CH MWEF CHLvTiOas Power Bright (SIP) Ltd Cover Letter for Wireless Charger Data:2020-11-11 Dear Sir/Madam, Theres a Multi-function Jump Starter _ that would like to have your authorization as an Inductive wireless power transfer applications approval. The specific product as below Wireless Charger with its designed features and specified description, meets special requirements for KDB 680106 DO1 section 5 b) requirements. Applicant: POWER BRIGHT (SIP) LTD Product Description: Input: 5V, 2.4A or 9V, 2.0A Output: USB : SVDC 2A; 9V 2A; 12V 2A Wireless Charger: 10W Max Boost: 12Vdc, 1000A (ims) ; 12Vdc, 100A (5s), ENJ1000, ENX1000, KRJ1000, KRX1000 a 1) Power transfer frequency is less than 1MHz =| Power transfer frequency is less than 1 MHz 110-149kHz Complied a Output power from each primary coil is less than 10W Complied 15 watts 3) The transfer system includes only single primary Models ENJ1000, ENX1000 and secondary cals. This includes charging systems KRJ1000, KRX1000 contains one that may have multiple primary coils and clients that : . wireless charging module, the are able to detect and allow coupling only between : :

a=. : 4 module contains only one coil. individual pairs of coils 4) Client device is inserted in or placed directly in Plated dinactly lntransenttter Complied contact with the transmitter 5) Mobile exposure conditions only Mobile Complied Complied 6) Aggregate leakage fields at 15 cm surrounding the device and 20cm above the top surface from all simultaneous transmitting coils are demonstrated to be less than 50% of the MPE limit. Complied Sincerely, By: UH ee ITN SF dackySun

(Print name)

ie a CIz Sits ip FOCUS LEADER 1H POWER BOLOTIR MS Power Bright (SIP) Ltd Statement of model Difference ENJ1000 is totally the same as ENX1000 only except it has different enclosure. KRJ1000 is totally the same as ENJ1000 only except the brand name. KRX1000 is totally the same as ENX1000 only except the brand name. Brand name Energizer is for ENJ1000, ENX1000. Brand name "KRIEGER" is for KRJ1000, KRX1000. By: Jacky Sun

(Print name) Title: General Manaq yer Date: 2020-11-11