FCC ID: RWO-RC30035302 WModule

FCC Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. This device complies with FCC radiation exposure limits set forth for an uncontrolled environment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Caution!

Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Canada Statement This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canadas licence-exempt RSS(s). Operation is subject to the following two conditions:

(1) This device may not cause interference.

(2) This device must accept any interference, including interference that may cause undesired operation of the device. Lmetteur/rcepteur exempt de licence contenu dans le prsent appareil est conforme aux CNR dInnovation, Sciences et Dveloppement conomique Canada applicables aux appareils radio exempts de licence. Lexploitation est autorise aux deux conditions suivantes

1) Lappareil ne doit pas produire de brouillage;

2) Lappareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible den compromettre le fonctionnement. The device meets the exemption from the routine evaluation limits in section 2.5 of RSS 102 and compliance with RSS-102 RF exposure, users can obtain Canadian information on RF exposure and compliance. Le dispositif rencontre l'exemption des limites courantes d'valuation dans la section 2.5 de RSS 102 et la conformit l'exposition de RSS-102 rf, utilisateurs peut obtenir l'information canadienne sur l'exposition et la conformit de rf.

. WIRELESS KEYBOARD (RZ03-0436) A. B. C. D. E. F. G. H. I. J. K. L. M. FO R G AM E R S. B Y G A M E R S . 1 FO R G AM E R S. B Y G A M E R S . 1 PRODUCT REQUIREMENTS RAZER SYNAPSE REQUIREMENTS FO R G AM E R S. B Y G A M E R S . 2 COLOR Red Orange Yellow Green STATUS Critical Very Low Low Charged FO R G AM E R S. B Y G A M E R S . 3 2.4 GHz mode FO R G AM E R S. B Y G A M E R S . 4 BT mode FO R G AM E R S. B Y G A M E R S . 5 WIRED MODE FO R G AM E R S. B Y G A M E R S . 6 FO R G AM E R S. B Y G A M E R S . 7 MEDIA CONTROLS KEYBOARD FUNCTIONS FO R G AM E R S. B Y G A M E R S . 8 ON-THE-FLY MACRO RECORDING GAMING MODE FO R G AM E R S. B Y G A M E R S . 9 CHROMA EFFECTS FO R G AM E R S. B Y G A M E R S . 10 SAFETY GUIDELINES COMFORT FO R G AM E R S. B Y G A M E R S . 11 MAINTENANCE AND USE FO R G AM E R S. B Y G A M E R S . 12 COPYRIGHT AND INTELLECTUAL PROPERTY INFORMATION LIMITED PRODUCT WARRANTY LIMITATION OF LIABILITY GENERAL FO R G AM E R S. B Y G A M E R S . 13 FO R G AM E R S. B Y G A M E R S . 14 FO R G AM E R S. B Y G A M E R S . 15 FCC Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. This device complies with FCC radiation exposure limits set forth for an uncontrolled environment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Caution!

Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. FCC SAR Exposure to Radio Frequency Energy (SAR) To maintain compliance with FCC RF exposure guidelines when you carry this device on your body, use only belt clips, holsters or similar accessories that have no metallic component in the assembly. Use of other non-approved accessories might violate FCC RF exposure guidelines. This equipment has been evaluated as a body worn device with 0 cm separation and complies with FCC radiation exposure limits set forth for an uncontrolled environment. In order to comply with FCC RF exposure safety guidelines, the antenna(s) used for this transmitter must not transmit simultaneously with any other antenna or transmitter, except in accordance with FCC multi-

transmitter product procedures. The user of this device should ensure that the operation of this device is in compliance with these provisions. FO R G AM E R S. B Y G A M E R S . 16 Canada Statement This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canadas licence-exempt RSS(s). Operation is subject to the following two conditions:

(1) This device may not cause interference.

(2) This device must accept any interference, including interference that may cause undesired operation of the device. Lmetteur/rcepteur exempt de licence contenu dans le prsent appareil est conforme aux CNR dInnovation, Sciences et Dveloppement conomique Canada applicables aux appareils radio exempts de licence. Lexploitation est autorise aux deux conditions suivantes

1) Lappareil ne doit pas produire de brouillage;

2) Lappareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible den compromettre le fonctionnement. FO R G AM E R S. B Y G A M E R S . 17

Specifications Manufacturer Name Manufacturing country (Full Address) Product Name Model Name Chipset Use (Specify: PMR, Amateur, Small Boats or other) Pl explain in detail the functionality Frequency/Frequency Range/BT/Lower power/Wifi?

//BT//Wifi RF Power output (EIRP) EIRP Modulation Channel Spacing:

rand of Antenna B Antenna Height Antenna Gain Antenna Type (Stubby Dipole):

9 Pasteur, Suite 100, Irvine, CA92618, USA Tech Specs for WModule Value Razer Inc. WModule RC30-035302 nRF52840 (QIAA) 2.4GHz and BLE Module 2.4G/BLE - 2402MHz to 2480MHz BLE: 1Mbps 6dBm BLE: 2Mbps 6dBm 2.4GHz: 2Mbps 6dBm GFSK Walsin, RFPCA451321IMAB301 BLE:2MHz 2.4GHz:1MHz PCB Antenna PCB on PCB 4.75dBi(max.) Product Picture FCC Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) this device may not cause harmful interference,

(2) this device must accept any interference received, including interference that may cause undesired operation. Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Caution!

Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. FCC Radiation Exposure Statement:

The modular can be installed or integrated in mobile, portable or fix devices. This modular complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. If the FCC identification number is not visible when the module is installed inside another device, then the outside of the device into which the module is installed must also display a label referring to the enclosed module. This exterior label can use wording such as the following:

Contains Transmitter Module FCC ID: RWO-RC30035302 or Contains FCC ID: RWO-RC30035302 . The devices must be installed and used in strict accordance with the manufacturer's instructions as described in the user documentation that comes with the product. When the module is installed inside another device, the user manual of this device must contain below warning statements:

1. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference.

(2) This device must accept any interference received, including interference that may cause undesired operation. 2. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protectio n against harmful interference in a residential installation. This equipment generates, uses and c an radiate radio frequency energy and, if not installed and used in accordance with the instruction s, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipme nt off and on, the user is encouraged to try to correct the interference by one of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

- Consult the dealer or an experienced radio/TV technician for help. Canada Statement This device complies with Industry Canadas licence-exempt RSSs. Operation is subject to the following two conditions:

(1) this device may not cause interference,

(2) this device must accept any interference, including interference that may cause undesired operation of the device. Le prsent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorise aux deux conditions suivantes :

(1) l'appareil ne doit pas produire de brouillage, et

(2) l'utilisateur de l'appareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible d'en compromettre le fonctionnement. Caution Exposure:

This device meets the exemption from the routine evaluation limits in section 2.5 of RSS102 and users can obtain Canadian information on RF exposure and compliance. Le dispositif rpond l'exemption des limites d'valuation de routine dans la section 2.5 de RSS102 et les utilisateurs peuvent obtenir des renseignements canadiens sur l'exposition aux RF et le respect. The final end product must be labelled in a visible area with the following:

The Industry Canada certification label of a module shall be clearly visible at all times when installed in the host device, otherwise the host device must be labelled to display the Industry Canada certification number of the module, preceded by the words Contains transmitter module, or the word Contains, or similar wording expressing the same meaning, as follows:

Contains transmitter module IC: 8092D-RC30035302 The module must be installed in WModule. The end user manual shall include all required regulatory information/warning as show in this manual. RF Specification RC30-035302 Module contains an integrated balun which provides a single-ended RF TX / RX IPEX connector. The transmitter has been optimised to deliver power in to a 50 load. And then,the RC30-035302 RF Spec base on N52840 DataSheet Bluetooth Transmitter Manual Information to the End User The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF module in the users manual of the end product which integrates this module. The end user manual shall include all required regulatory information/warning as show in this manual.

Barcode spec:

Format: 128 Size: 50mm x 5mm CM please ensure while scanning, barcode result SHOULD NOT INCLUDED the S/N:

Font: RazerF5 Regular, 7 pt. Olive T1 (Linear Red Switch)- PID label Rev: 202202 by Gary@ Razer Size: 126.6 x 39.2mm Printing: 1C Material: PET sticker with matte lamination 1:1 scale

[LINEAR OPTICAL SWITCH]

CMIIT ID: XXXXXXXXXXX SDPPI: XXXXXX/SDPPI/2022 CAN ICES-003(B)/

NMB-003(B) R39212 RoHS IS 13252 (Part 1)/

IEC 60950-1 Contains Module model: RC30-035302 FCC ID: RWO-RC30035302 IC: 8092D-RC30035302 S/N: PM22WWAAAAXXXXX MODEL NO. [/]: RZ03-0436 Wireless Keyboard// P/NO. [/]:

RATING [/]: 5V 2.0A This device is manufactured under one or more of the following patents:

U.S. Pat. Nos. 8,367,947; 8,605,063; 9,841,825; 8,566,431; 9,235,277 P.R.C. Pat. Nos. ZL200680054309.2; ZL201410360065.7; ZL200780100766.5; ZL 200980102126.7; ZL201180058303.3 TW Pat. Nos. I 370219 ; I 507922; I 484339; I 493360 KR Pat. Nos. 10-1278955; 10-1451249; 10-1433277; 10-1600078; 10-1770419. Further patents pending in various territories. R-R-RAZ-

RZ03-0436 CCAH20LP6920T1 R-XXXXXX R-R-RAZ-RC30-035302 Razer (Europe) GmbH Essener Bogen 23, 22419 Hamburg, Germany 201-XXXXXX RAZER INC.

MADE IN CHINA Razer F5 Regular font, 7 pointsize Complete sku P/N. reference:

RZ03-0436XX00-R3X1

RF_160, Issue 02 Razer Inc. Declaration of Authorization We Name: Razer Inc. Address: 9 Pasteur, Suite 100 City: Irvine State: California Country: United States Declare that:

Name Representative of agent: Ms. Rose Liu Agent Company name: BTL Inc. Address: No.3 Jinshagang 1st Road, Shixia, Dalang Town City: Dong Guan Country: China is authorized to apply for Certification and signing related documents of the following product(s), including 731 form(s):

Product description: Wmodule Type designation: RC30-035302 Trademark: RAZER FCC ID : RWO-RC30035302 on our behalf. Date: 2022-06-16 City: Irvine Name: Johnsen Tia Function: Senior Director, Regulatory & Compliance Signature: . Notes:

(1): Required for FCC application

(2): For FCC it must be the Grantee Code owner or the authorized agent.

Razer Inc. Federal Communications Commission 7435 Oakland Mills Road Columbia MD 21046 C.C.: Telefication B.V., Dept. FCC TCB Edisonstraat 12A 6902 PK ZEVENAAR The Netherlands Subject: Requesting Class II permissive change for FCC ID: RWO-RC30035302 To Whom It May Concern:

The purpose of this letter is to request a Class II Permissive change for FCC ID: RWO-RC30035302, original granted on 09/15/2020. 1. The subject approved limited module, and it is to register or add the specific host (s) of the portable one - a Wireless Keyboard (Brand name/Model: RAZER/ RZ03-0436). 2. The identical antenna are being used. Original module:

Wireless Keyboard:

Please contact me if you have any questions or need further information regarding this application. Best Regards, Name: Johnsen Tia Funtion: Senior Director, Regulatory & Compliance Date: 2022-06-16 Signed :

FCC, Request for non-disclosure RF_501, Issue 5 Date: 10-Aug-09 Page 1 of 1 Company Name: Razer Inc. Address:

City:

Country:

9 Pasteur, Suite 100 Irvine California United States Edisonstraat 12A 6902 PK ZEVENAAR The Netherlands To: Telefication B.V., Dept. FCC TCB Subject: Request for confidentiality FCC ID: RWO-RC30035302 Reference number: ######

Dear FCC TCB, 1. Long-Term Confidentiality Pursuant to 47 CFR Section 0.459(a) & (b), we hereby requests non-disclosure and confidential treatment of the following materials submitted in support of FCC certification application:

Bill(s) of Material Block Diagrams Operational Description Schematic Diagrams Tune-up Procedure Above materials contain secrets, proprietary and technical information, which would customarily be guarded from competitors under 47 CFR, section 0.457(d)(2). Disclosure or publication or any portion of this company confidential material to other parties could cause substantial competitive harm and provide unjustified benefits for competitors. 2. Short-Term Confidentiality (STC) Pursuant to Public Notice DA 04-1705 of the Commissions policy, in order to comply with the marketing regulations in 47 CFR 2.803 and the importation rules in 47 CFR 2.1204, applicant hereby requests Short-Term Confidential treatment of the following materials (note 1):

Internal Photos Users Manual Test Set-up Photos External Photos Justification: This document contains detailed system and equipment description are considered as proprietary information in operation of the equipment. The public disclosure of above documents might be harmful to our company and would give competitor unfair advantage in the market. Planned Release Date STC: 180 days from date of grant (notes 2, 3, 4, 5) Name and signature of applicant: Johnsen Tia Senior Director, Date: 2022-06-24 Regulatory & Compliance Notes:

1) A document or type of document can only have ONE type of confidentiality!

2) Short-Term confidentiality is in principle for 45 days from date of grant; it can be extended max 3 times (total time 180 days max.)!

3) FCC must be informed when marketing begins earlier. 4) Release takes place automatically thus extension must be requested in time. Telefication does not remind you of this!

FCC, Request for non-disclosure RF_501, Issue 5 Date: 10-Aug-09 Page 1 of 1 5) Request for extension or for release must be received by Telefication at least 7 days before date of actual marketing or before expiration of the STC period

RF_160, Issue 02 Declaration of Authorization We Name: Razer Inc. Address: 9 Pasteur, Suite 100 City: Irvine State: California Country: United States Declare that:

Name Representative of agent: Ms. Rose Ll Agent Company name: BTL Inc. Address: No.3 Jinshagang 1st Road, Shixia, Dalang Town City: Dong Guan Country: China is authorized to apply for Certification and signing related documents of the following product(s), including 731 form(s):

Product description: WModule Type designation: RC30-035302 Trademark: RAZER FCC ID : RWO-RC30035302 on our behalf. Date: 2021-03-02 City: Irvine Name: Johnsen Tia Function: Senior Director, Regulatory & Compliance Signature: . Notes:

(1): Required for FCC application

(2): For FCC it must be the Grantee Code owner or the authorized agent.

Razer Inc. Federal Communications Commission 7435 Oakland Mills Road Columbia MD 21046 C.C.: Cetecom GmbH, Im Teelbruch 116, 45219 Essen, Germany Subject: Requesting Class II permissive change for FCC ID: RWO-RC30035302 To Whom It May Concern:

The purpose of this letter is to request a Class II Permissive change for FCC ID: RWO-RC30035302, original granted on 09/15/2020. 1. The subject approved limited module, and it is to register or add the specific host (s) of the portable one - a Wireless Keyboard (Brand name/Model: RAZER/ RZ03-0389). 2. The identical antenna are being used. Original module:

Wireless Keyboard:

Please contact me if you have any questions or need further information regarding this application. Best Regards, Name: Johnsen Tia Funtion: Senior Director, Regulatory & Compliance Date: 2021-03-03 Signed :

RF_734_02 04 April 16 2. 3. 4. 5. 8. Modular Approval Request FCC (KDB 996369 D01 & Part 15.212) FCC ID: RWO-RC30035302 Items to be covered by Single modular transmitters. 1. The modular transmitter must have its own RF shielding. The modular transmitter must have buffered modulation/data inputs (if such inputs are provided) to ensure that the module will comply with Part 15 requirements under conditions of excessive data rates or over-modulation. The modular transmitter must have its own power supply regulation. The modular transmitter must comply with the antenna requirements of Section 15.203 and 15.204(b)(c). The antenna must either be permanently attached or employ a unique antenna coupler (at all connections between the module and the antenna, including the cable). Answer from applicant YES, Please refer to External Photos. YES, U1 N52840 is used for the function. NO YES, it is PCB antenna. The modular transmitter must be tested in a stand-alone configuration, i.e., the module must not be inside another device during testing. This is intended to demonstrate that the module is capable of complying with Part 15 emission limits regardless of the device into which it is eventually installed. Yes, the module is tested in a stand-alone configuration as the test photos show. 6. The modular transmitter must be equipped with either a permanently affixed label or must be capable of electronically displaying its FCC identification number in accordance with 15.212 (a)(1)(vi)(A) / (B). YES, please refer to the exhibition label sample for this module. 7. The modular transmitter must comply with any specific rule or operating requirements applicable to the transmitter and the manufacturer must provide adequate instructions along with the module to explain any such requirements. A copy of these instructions must be included in the application for equipment authorization. For example, timing requirements that must be met before a transmitter is authorized for operation under Section 15.231. For instance, data transmission is prohibited, except for operation under Section 15.231(e), in which case there are separate field strength level and timing requirements. Compliance with these requirements must be assured. there are very strict operational and The modular transmitter must comply with any applicable RF exposure requirements. For example, FCC Rules in Sections 1.1310, 2.1091, 2.1093, and specific Sections of Part 15, including 15.319(i), 15.407(f), 15.253(f) and 15.255(g), require that Unlicensed PCS, UNII and millimeter wave devices perform routine environmental evaluation for RF Exposure to demonstrate compliance. In addition, spread spectrum transmitters operating under Section 15.247 are required to address RF Exposure compliance. Modular transmitters approved under other Sections of Part 15, when necessary, may also need to address certain RF Exposure concerns, typically by providing specific installation and operating instructions for users, installers and other interested parties to ensure compliance. YES, please refer to the user manual. YES, RF exposure statement is attached in the user manual. Note: A limited modular approval (LMA) may be granted for single or split modular transmitters that comply partially with the requirements above. Name and surname of applicant (or authorized representative): Johnsen Tia Date: 2020-07-20 Signature: ___________________________

FCC, Request for non-disclosure RF_501, Issue 5 Date: 10-Aug-09 Page 1 of 1 Company Name: Razer Inc. Address:

City:

Country:

9 Pasteur, Suite 100 Irvine California United States Edisonstraat 12A 6902 PK ZEVENAAR The Netherlands To: Telefication B.V., Dept. FCC TCB Subject: Request for confidentiality FCC ID: RWO-RC30035302 Reference number: ######

Dear FCC TCB, 1. Long-Term Confidentiality Pursuant to 47 CFR Section 0.459(a) & (b), we hereby requests non-disclosure and confidential treatment of the following materials submitted in support of FCC certification application:

Bill(s) of Material Block Diagrams Operational Description Schematic Diagrams Tune-up Procedure Above materials contain secrets, proprietary and technical information, which would customarily be guarded from competitors under 47 CFR, section 0.457(d)(2). Disclosure or publication or any portion of this company confidential material to other parties could cause substantial competitive harm and provide unjustified benefits for competitors. 2. Short-Term Confidentiality (STC) Pursuant to Public Notice DA 04-1705 of the Commissions policy, in order to comply with the marketing regulations in 47 CFR 2.803 and the importation rules in 47 CFR 2.1204, applicant hereby requests Short-Term Confidential treatment of the following materials (note 1):

Internal Photos Users Manual Test Set-up Photos External Photos Justification: This document contains detailed system and equipment description are considered as proprietary information in operation of the equipment. The public disclosure of above documents might be harmful to our company and would give competitor unfair advantage in the market. Planned Release Date STC: 180 days from date of grant (notes 2, 3, 4, 5) Name and signature of applicant: Johnsen Tia Senior Director, Regulatory Date: 2020-07-20

& Compliance Notes:

1) A document or type of document can only have ONE type of confidentiality!

2) Short-Term confidentiality is in principle for 45 days from date of grant; it can be extended max 3 times (total time 180 days max.)!

3) FCC must be informed when marketing begins earlier. 4) Release takes place automatically thus extension must be requested in time. Telefication does not remind you of this!

FCC, Request for non-disclosure RF_501, Issue 5 Date: 10-Aug-09 Page 1 of 1 5) Request for extension or for release must be received by Telefication at least 7 days before date of actual marketing or before expiration of the STC period