Realtek Ameba1 DEV01 User Manual This document define pin out of Ameba DEV. Version 1.5 Document Number: UM0058 _______________________________________________________________ Table of Contents 1 2 3 4 5 Hardware block diagram ......................................................................................................... 3 System requirements .............................................................................................................. 4 Pin out reference ..................................................................................................................... 4 3.1 Pin out table .................................................................................................................... 4 3.2 Pin out reference ............................................................................................................ 5 3.3 Pin connection table ...................................................................................................... 6 Antenna hardware setup ........................................................................................................ 7 Peripherals support ................................................................................................................. 7 5.1 Pin function table setup .................................................................................................. 8 6 Hardware configuration .......................................................................................................... 8 6.1 CMSIS-DAP ...................................................................................................................... 8 6.2 J-Link/JTAG ...................................................................................................................... 9 6.3 DAP mode ..................................................................................................................... 11 7 8 Ameba1 DEV01 pin out ......................................................................................................... 13 Sensor board ......................................................................................................................... 14 9 Warning ................................................................................................................................. 15 10.1 Federal Communication Commission Interference Statement ....................................... 15 10.2 Industry Canada Statement ......................................................................................... 17 10.3 NCC ....................................................................................................................... 20 10.4 Japan Statement ............................................................................................................... 20 March 8, 2016 2 Document Number: UM0058 _______________________________________________________________ 1 Hardware block diagram IC: RTL8195AM DEV HDK version: RTL-AMEBA_DEV01_1v1 J22 J20 NFC Antenna Wi-Fi external ANT connector Wi-Fi PCB Antenna J-TAG UART RTL8711AF DAP DAP+DC
+serial port USB Host DC 5V Ameba reset button J21 J19 DAP update Mode button DAP reset button March 8, 2016 3 Document Number: UM0058 _______________________________________________________________ 2 System requirements Windows PC (XP, Vista, 7) USB type A to Micro-B USB cable x 1 RS-232 to UART board(debug) x 1, JTAG cable x1 (option) 3 Pin out reference 3.1 Pin out table Con DEV name Pin Net name Con DEV name J20 I2C_SCL*
I2C_SDA*
DAC A2 A1 A0 6 GPIOD_6 5 GPIOD_7 4 DAC_CH0 3 ADC_CH2 2 ADC_CH1 1 ADC_CH1 J19 RX/D0 TX/D1 D2 D3/PWM2*
D4/PWM1*
D5 D6 D7 Con DEV name Pin Net name Con VIN GND GND 5V 3.3V RESET IOREF RSVD D16 D17 D18 RSVD sJ22 12 NC 11 GROUND 10 GROUND 9 5VDD 8 VDD33 7 NC 6 VDD33 5 NC 4 GPIOA_1 3 GPIOA_0 2 GPIOE_5 1 NC J21 DEV name D8/PWM0*
D9/PWM1*
D10/CS/PWM0 D11/MOSI/PWM2 D12/MISO/PWM3 D13/SCK/PWM1 GND AREF I2C_SDA I2C_SCL D14 D15 Pin Net name 8 GPIOA_6 7 GPIOA_7 6 GPIOA_5 5 GPIOD_4 4 GPIOD_5 3 GPIOA_4 2 GPIOA_3 1 GPIOA_2 Pin Net name 12 GPIOB_4 11 GPIOB_5 10 GPIOC_0 9 GPIOC_2 8 GPIOC_3 7 GPIOC_1 6 GND 5 VDD33 4 GPIOC_4 3 GPIOC_5 2 GPIOB_3 1 GPIOB_2 March 8, 2016 4 Document Number: UM0058 _______________________________________________________________ 3.2 Pin out reference GPIOD_6 GPIOD_7 DAC_CH0 ADC_CH2 ADC_CH1 ADC_CH1 GND GND 5VDD VDD33 VDD33 GPIOA_1 GPIOA_0 GPIOE_5 GPIOA_6 GPIOA_7 GPIOA_5 GPIOD_4 GPIOD_5 GPIOA_4 GPIOA_3 GPIOA_2 GPIOB_4 GPIOB_5 GPIOC_0 GPIOC_2 GPIOC_3 GPIOC_1 GND VDD33 GPIOC_4 GPIOC_5 GPIOB_3 GPIOB_2 March 8, 2016 5 Document Number: UM0058 _______________________________________________________________ 3.3 Pin connection table March 8, 2016 6 PCB Decal nameI2C_SCL*I2C_SDA*DACA2A1A0VINGNDGND5V3.3VRESETIOREFRSVDD16D17D18RSVDJ20J22Header Pin Num654321121110987654321Module Pin Num56161514142019128DEV board Pin net GPIOD_6GPIOD_7DAC_CH0ADC_CH2ADC_CH1ADC_CH1NCGROUNDGROUND5VDDVDD33NCVDD33NCGPIOA_1GPIOA_0GPIOE_5GPIO_AGPIO_BCON2GPIO_CGPIO_DGPIO_ECON1DEV board Pin net GPIOA_6GPIOA_7GPIOA_5GPIOD_4GPIOD_5GPIOA_4GPIOA_3GPIOA_2GPIOB_4GPIOB_5GPIOC_0GPIOC_2GPIOC_3GPIOC_1GROUNDVDD33GPIOC_4GPIOC_5GPIOB_3GPIOB_2Module Pin Num2625243423222146473937363840414243Header Pin Num87654321121110987654321J19J21RX/D0TX/D1D2D3/PWM2*D4/PWM1*D5D6D7D8/PWM0*D9/PWM1*D10/CS/PWM0D11/MOSI/PWM2D12/MISO/PWM3D13/SCK/PWM1GNDAREFI2C_SDAI2C_SCLD14D15RTL-AMEBA_DEV01RTL8195AM Document Number: UM0058 _______________________________________________________________ 4 Antenna hardware setup I-PEX/U.FL connector: R206 External antenna: R207 PCB antenna: R208 6 0 2 R R207 R208 5 Peripherals support Debug UART: GPIOB_[0..1]
March 8, 2016 7 Document Number: UM0058 _______________________________________________________________ JTAG: GPIOE_[0..4]
5.1 Pin function table setup Multiple functions are supported by group setup. For example: GPIOA_6(Rx), GPIOA_7(Tx), GPIOA_3(RTS) and GPIOA_5(CTS) are used if UART0 function. GPIOA_3(RTS) and GPIOA_5(CTS) can not be used as other functions. For example: GPIOC_0, GPIOC_1, GPIOC_2, GPIOC_2, GPIOC_3 are used if PWM is occupied. GPIOC_1(PWM1) and GPIOC_2(PWM2) can not be used as other functions. 6 Hardware configuration 6.1 CMSIS-DAP RTL-AMEBA_DEV01 supports CMSIS-DAP debugger. It requires installing serial to USB driverat first. Serial to USB driver can be found in tools\serial_to_usb\mbedWinSerial_16466. Connect board to the PC with micro-USB cable. March 8, 2016 8 Document Number: UM0058 _______________________________________________________________ 6.2 J-Link/JTAG Weld JTAG and log UART connectors to HDK board and connect with pitch 2.54mm 2x5pins connector. It is recommended to weld the connector on the bottom side. Users can connect extension boards from top side. March 8, 2016 9 Document Number: UM0058 _______________________________________________________________ JTAG 5V DC UART Dupont Line or 2.54mm 2x5 pins connector. Power On(Disable DAP mode) Holding TGT_NRESET button (J24, red-circled) then press Pdn button (J13, blur-
circled). Release the button after power on. March 8, 2016 10 Document Number: UM0058 _______________________________________________________________ J24 J17 J13 6.3 DAP mode In DAP mode, the DAP firmware can be updated. Holding TGT_NRESET button (J24, red-circled) then press nRESET button (J17, blur-circled). Then the DAP mode window will show up. March 8, 2016 11 Document Number: UM0058 _______________________________________________________________ J24 J17 J13 DAP window will show up when entering DAP mode. March 8, 2016 12 Document Number: UM0058 _______________________________________________________________ 7 Ameba1 DEV01 pin out March 8, 2016 13 Document Number: UM0058 _______________________________________________________________ 8 Sensor board Extension board: RTL-AMEBA_EXT B2_2V0 March 8, 2016 14 Document Number: UM0058 _______________________________________________________________ 9 Warning 10.1 Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:
-
-
-
-
Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. March 8, 2016 15 Document Number: UM0058 _______________________________________________________________ IMPORTANT NOTE:
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. IEEE 802.11b or 802.11g operation of this product in the U.S.A. is firmware-limited to channels 1 through 13. This device and its antenna(s) must not be co-located with any other transmitters except in accordance with FCC multi-transmitter product procedures. Refering to the multi-transmitter policy, multiple-transmitter(s) and module(s) can be operated simultaneously without C2PC. This module is intended for OEM integrator. The OEM integrator is responsible for the compliance to all the rules that apply to the product into which this certified RF module is integrated. Additional testing and certification may be necessary when multiple modules are used. USERS MANUAL OF THE END PRODUCT:
In the users manual of the end product, the end user has to be informed to keep at least 20cm separation with the antenna while this end product is installed and operated. The end user has to be informed that the FCC radio-frequency exposure guidelines for an uncontrolled environment can be satisfied. The end user has to also be informed that any changes or modifications not expressly approved by the manufacturer could void the user's authority to operate this equipment. If the size of the end product is smaller than 8x10cm, then additional FCC part 15.19 statement is required to be available in the users manual: This device complies with Part 15 of FCC rules. Operation is subject to the following two conditions: (1) this device March 8, 2016 16 Document Number: UM0058 _______________________________________________________________ may not cause harmful interference and (2) this device must accept any interference received, including interference that may cause undesired operation. LABEL OF THE END PRODUCT:
The final end product must be labeled in a visible area with the following " Contains TX FCC ID:
TX2-RTL8195AM ". If the size of the end product is larger than 8x10cm, then the following FCC part 15.19 statement has to also be available on the label: This device complies with Part 15 of FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference and (2) this device must accept any interference received, including interference that may cause undesired operation. 10.2 Industry Canada Statement This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions:
1) this device may not cause interference and 2) this device must accept any interference, including interference that may cause undesired operation of the device French translation:
Ce dispositif est conforme aux CNR d'IndustrieCanada applicable aux appareils radio exempts de licence. Son fonctionnement est sujet aux deux conditions suivantes: (1) le dispositif ne doit pas produire de brouillage prjudiciable, et (2) ce dispositif doit accepter tout brouillage reu, y compris un brouillage susceptible de provoquer un fonctionnement indsirable. This device has been designed to operate with an antenna having a maximum gain of 3.5dBi. Antenna having a higher gain is strictly prohibited per regulations of Industry Canada. The required antenna impedance is 50 ohms. March 8, 2016 17 Document Number: UM0058 _______________________________________________________________ To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the EIRP is not more than required for successful communication. This module is intended for OEM integrator. The OEM integrator is responsible for the compliance to all the rules that apply to the product into which this certified RF module is integrated. Additional testing and certification may be necessary when multiple modules are used. French translation:
Ce dispositif a t conu pour fonctionner avec une antenne ayant un gain maximum de 3.5 dBi. Une antenne gain plus lev est strictement interdite par les rglements d'Industrie Canada. L'impdance d'antenne requise est de 50 ohms. Conformment la rglementation d'Industrie Canada, le prsent metteur radio peutfonctionner avec une antenne d'un type et d'un gain maximal (ou infrieur) approuv pourl'metteur par Industrie Canada. Dans le but de rduire les risques de brouillage radiolectrique l'intention des autres utilisateurs, il faut choisir le type d'antenne et son gain de sorte que lapuissance isotrope rayonne quivalente (p.i.r.e.) ne dpasse pas l'intensit ncessaire l'tablissement d'une communication satisfaisante. IMPORTANT NOTE:
IC Radiation Exposure Statement:
This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. French translation:
NOTE IMPORTANTE: (Pour l'utilisation de dispositifs mobiles) Dclaration d'exposition aux radiations:
Cet quipement est conforme aux limites d'exposition aux rayonnements IC tablies pour un environnement non contrl. Cet quipement doit tre install et utilis avec un minimum de 20 cm de distance entre la source de rayonnement et votre corps. For product available in the Canada market, only channel 1~11 can be operated. Selection of other channels is not possible. March 8, 2016 18 Document Number: UM0058 _______________________________________________________________ French translation:
Pour les produits disponibles aux Canada du march, seul le canal 1 11 peuvent tre exploits. Slection d'autres canaux n'est pas possible. This device and its antenna(s) must not be co-located with any other transmitters except in accordance with IC multi-transmitter product procedures. Refering to the multi-transmitter policy, multiple-transmitter(s) and module(s) can be operated simultaneously without reassessment permissive change. Cet appareil et son antenne (s) ne doit pas tre co-localiss ou fonctionnement en association avec une autre antenne ou transmetteur. USERS MANUAL OF THE END PRODUCT:
In the users manual of the end product, the end user has to be informed to keep at least 20cm separation with the antenna while this end product is installed and operated. The end user has to be informed that the IC radio-frequency exposure guidelines for an uncontrolled environment can be satisfied. The end user has to also be informed that any changes or modifications not expressly approved by the manufacturer could void the user's authority to operate this equipment. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference and (2) this device must accept any interference received, including interference that may cause undesired operation. LABEL OF THE END PRODUCT:
The final end product must be labeled in a visible area with the following " Contains TX IC :
6317A-RTL8195AM ". This radio transmitter (IC: 6317A-RTL8195AM) has been approved by Industry Canada to operate with the antenna types listed below with the maximum permissible gain and required antenna impedance for each antenna type indicated. Antenna types not included in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device. French translation:
Le prsent metteur radio (IC: 6317A-RTL8195AM) a t approuv par Industrie Canada pour fonctionner avec les types d'antenne numrs ci-dessous et ayant un gain admissible maximal et l'impdance requise pour chaque type d'antenne. Les types March 8, 2016 19 Document Number: UM0058 _______________________________________________________________ d'antenne non inclus dans cette liste, ou dont le gain est suprieur au gain maximal indiqu, sont strictement interdits pour l'exploitation de l'metteur. The following antenna type and max. gain be used and approved for the module:
1) Dipole antenna, max. gain: 3dBi 2) PIFA antenna, max. gain: 3.5dBi 3) Printed antenna, max. gain: 2dBi 4) PIFA antenna, max. gain:2.89dBi 10.3 NCC XXXyyyLPDzzzz-x (NCC ID) 10.4 Japan Statement Host system must be labeled with "Contains MIC ID:xxxx, MIC ID displayed on label March 8, 2016 20