FCC ID: CHQ9054TA Transmitter

INSTRUCTIONS FOR OPERATION SETING THE OPERATING CONTROLS 1. Provide DC 7-12V power. 2. Store the controller away from excess heat or humidity . 3. Operation buttons on the panel of transmitter . key For light brightness and light ON/OFF control . key For fan 4 speed (HIGH) control . key For fan 3 speed control . key For fan 2 speed control . Key For fan LOW speed control . key For fan ON / OFF control . POWER SWITCH for POWER ON/OFF 1/4 4. Fan control :

Press the fan speed button,to select the needed speed. 5. Light control :

Turn the light on or off by only touching the LIGHT button . Keep pressing the button in excess of 0.7 second it becomes a dimmer , 6. Power switch Turn off the power for Fan and Light GENERAL INFORMATION :

This remote controller is designed to separately control your ceiling fan speed and light brightness . INSTRUCTIONS FOR INSTALLATION AND OPERATION OF FAN SPEED CONTROLLER Setup for ceiling fan controller 1. Turn off the power. (In order to make sure the electricity is entirely released, please press any button on the controller till no LED display showing) 2. Turn on the power 3. Press the FAN OFF button for more than 3 sec. The ceiling fan controller will has 2 blinks. It means the setup is successful. You could start to control the ceiling fan light and fan speed. NOTICE :

The changes or modifications not expressly approved by the party responsible for compliance could void users authority to operate the equipment . 2/4 IMPORTANT NOTE: To comply with the FCC RF exposure compliance requirements, no change to the antenna or the device is permitted. Any change to the antenna or the device could result in the device exceeding the RF exposure requirements and void users authority to operate the device. FEDERAL COMMUNICATIONS COMMISSION INTERFERENCE STATEMENT This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

-Reorient or relocate the receiving antenna.

-Increase the separation between the equipment and receiver.

-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

-Consult the dealer or an experienced radio/ TV technician for help. CAUTION:

Any changes or modifications not expressly approved by the grantee of this device could void the user's authority to operate the equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause 3/4 Canada, Industry Canada (IC) Notices This device complies with Canada licenceexempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Canada, avis d'Industry Canada (IC) Cet appareil est conforme avec Industrie Canada exemptes de licence RSS standard(s). Son fonctionnement est soumis aux deux conditions suivantes : (1) cet appareil ne doit pas causer d'interfrence et (2) cet appareil doit accepter toute interfrence, notamment les interfrences qui peuvent affecter son fonctionnement. Radio Frequency (RF) Exposure Information The radiated output power of the Wireless Device is below the Industry Canada (IC) radio frequency exposure limits. The Wireless Device should be used in such a manner such that the potential for human contact during normal operation is minimized. person's body). This device has also been evaluated and shown compliant with the IC RF Exposure limits under portable exposure conditions. (antennas are less than 20 cm of a Informations concernant l'exposition aux frquences radio (RF) La puissance de sortie mise par lappareil de sans fil est infrieure la limite d'exposition aux frquences radio d'Industry Canada (IC). Utilisez lappareil de sans fil de faon minimiser les contacts humains lors du fonctionnement normal. Ce priphrique a galement t valu et dmontr conforme aux limites d'exposition aux RF d'IC dans des conditions d'exposition des appareils portables.

(les antennes sont moins de 20 cm du corps d'une personne). 4/4

14mm 12mm

MODEL : UC9054TA FCC ID : CHQ9054TA IC : 2968A-9054TA Complies with Canada RSS210 This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions:

(1)This device may not cause harmful interference and

(2)This device must accept any interference received, Including interference that

\ may cause undesired operation. IN 23mm piseesad (S)ON JusIed sn 52mm MODEL : UC9054TA This control to be used only with a Cc US a fan speed control. USTED FAN SPEED CONTROL E161552 8F36 T RHINE ELECTRONIC CO.,LTD. MADE IN TAIWAN

=> asada angen P eo aaa PaNICC es oats guuaplto the following two |

C Moet: ucsesara er fogecseee dit yis'cesa Lon qooied sr Atataccet any aa erties ose

\ = eis Label location

No. 29, Fong Li Road, Tan-Zi Dist, Taichung City 42754,Taiwan DATE : 2022/1/3 Equipment Autorisation Division Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 FCC ID: CHQ9054TA Product Name: Transmitter Request for Confidentiality Pursuant to Sections 0.457 and 0.459 of the commissions rules, we hereby request that the following documents be held confidential:

These materials contain trade secrets and proprietary information and are not customarily released to the public. The public disclosure of this information might be harmful to the company and provide unjustified benefits to our competitors. Schematics Block diagram Operation description Dated this 2022/1/3 By:

Signature Title: General manager Joseph Liao Printed On behalf of :

RHINE ELECTRONIC CO., LTD.

No. 29, Fong Li Road, Tan-Zi Dist, Taichung City 42754,Taiwan DATE : 2022/1/3 Nemko Canada Inc 303 River Road Ottawa, Ontario, Canada K1V 1H2 Attn: Director of Certification (FCC ID: CHQ9054TA; IC : 2968A-9054TA) Authority to Act as Agent On our behalf, I appoint Chenz Ker (MRT Technology (Taiwan) Co., Ltd./ No.38 Fuxing 2nd Road, Guishan Dist., Taoyuan City, Taiwan 33377). to act as our agent in the preparation of this application for equipment certification. I certify that submitted documents properly describe the device or system for which equipment certification is sought. I also certify that each unit manufactured, imported or marketed, as defined in the Federal Communications Commissions regulations will have affixed to it a label identical to that submitted for approval with this application. For instances where our authorized agent signs the application for certification on our behalf, I acknowledge that all responsibility for complying with the terms and conditions for certification, as specified by Nemko Canada Inc, still resides with Rhine Electronics Co Ltd / NO. 29, AN HE ROAD,TAN-ZI SHIANG, TAICHUNG COUNTY, 427 Taiwan Dated this 2022/1/3 Agency agreement expiration date:

2022/4/3 By:

Signature Title: General manager Joseph Liao Printed On behalf of :

RHINE ELECTRONIC CO., LTD.

No. 29, Fong Li Road, Tan-Zi Dist, Taichung City 42754,Taiwan DATE : 2022/1/3 Equipment Autorisation Division Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 FCC ID: CHQ9054TA Product Name: Transmitter Request for Short-Term Confidentiality Test Setup Photos External Photos Internal Photos User Manual Pursuant to Sections 0.457 and 0.459 of the commission rules, and in accordance with the FCC Public notice dated June 15, 2004 (DA 04-1705), we hereby request short-term confidentiality for the following items prior to marketing the device.:

These documents contain detailed system and equipment description and related information about the product which Rhine Electronics Co., Ltd. considers to be proprietary, confidential, and a custom design and, otherwise would not release to the general public. Since this design is a basis from which future technological products will evolve, Rhine Electronics Co., Ltd. considers this information to be of benefit to its competitors, and that the disclosure of information in these documents would give competitors an unfair advantage in the market. This request is being made retroactively due to an over site on our part. We understand that the information has been publicly available 180 days after date of grant. Dated this 2022/1/3 By:

Signature Title: General manager Joseph Liao Printed On behalf of :

RHINE ELECTRONIC CO., LTD. Telephone: 886 4-2531-2825