FCC ID: 2AYIBRV001 Ride Vision 1

The board has two antenna, the one is WI-FI/BT antenna, the other is GPS antenna. Ride Vision 1 Instructions Power on the device 1. Connect the #2 Type-C port with DC adapter 2. The LED turn on when the DC adapter insert. Antenna SD Card Network The board has support the SD Card, you can insert the SD card. The board has WI-FI module, you can get network with WI-FI USB-C connections The board has two USB-C connections. They can be used for the following:

1. Connecting a USB external device. 2. Connecting a DC adater. Electrical and Performance Specification Ride Vision 1 Ride Vision 1 Connecting a USB external device WiFi:

BT:

IEEE802.11a, IEEE802.11b, IEEE802.11g, IEEE802.11n, IEEE802.11ac, BT V5.0 BT:2.402~2.48GHz(BT) 2.4GWIFI:2.412~2.472GHz(USA 5GWIFI:5.18~5.24GHz/5.745~5.825GHz Wifi802.11b: CCK, DQPSK, DBPSK 11Channels, Europe and others 13 channels) 802.11a/g: 64-QAM, 16-QAM, QPSK, BPSK 802.11n: 64-QAM, 16-QAM, QPSK, BPSK 802.11ac: 256-QAM, 64-QAM, 16-QAM, QPSK, BPSK BT: 8DPSK, /4 DQPSK, GFSK 1575.42MHz Wifi802.11b: 11, 5.5, 2, 1 Mbps 802.11a/g: 54, 48, 36, 24, 18, 12, 9, 6 Mbps 802.11n: MCS 0 to 7 for HT20 802.11ac: MCS 0 to 9 for VHT80 BT: 1 Mbps for Basic Rate and LE Mode; 2,3 Mbps for Enhanced Data Rate IEEE 802.11b: DSSS (Direct Sequence Spread Spectrum) IEEE 802.11a/g/n/ac:OFDM (Orthogonal Frequency Division Multiplexing) BT: FHSS(Frequency-Hopping Spread Spectrum) RF Power(Typical) 2.4GWiFi:13.01dBm(Max) 5.2GWiFi:13.22dBm(Max) 5.8GWiFi:12.14dBm(Max) BT:4.464dBm(Max) BLE:1.395dBm(Max) Antenna type Power supply FPC Antenna, 4.0dBi(Max.) DC 12V Item Product Name Model Host Interface Standard Frequency Range Modulation Type GPS Data Transfer Rate Spread Spectrum FCC Statement This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) thi s device may not cause harmful interference, and (2) this device must accept any interference received, incl uding interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursua nt to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful inte rference in a residential installation. This equipment generates uses and can radiate radio frequency energy a nd, if not installed and used in accordance with the instructions, may cause harmful interference to radio com munications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turn ing the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help important announcement Important Note:

Radiation Exposure Statement This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 0cm between the radiator and your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Country Code selection feature to be disabled for products marketed to the US/Canada. This device is intended only for OEM integrators under the following conditions:

1. The antenna must be installed such that 20 cm is maintained between the antenna and users, and 2. The transmitter module may not be co-located with any other transmitter or antenna, 3. For all products market in US, OEM has to limit the operation channels in CH1 to CH11 for 2.4G band supplied firmware programming tool. OEM shall not supply any tool or info to the end-user Regulatory Domain change.

(if modular only test Channel 1-11) the event As long as the three conditions above are met, further transmitter testing will not be required. However, the OEM integrator is still responsible for testing their end-product for any additional compliance requirements required with this module installed. Important Note:

In co-location that with another transmitter), then the FCC authorization is no longer considered valid and the FCC ID cannot be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product (including the transmitter) and obtaining a separate FCC authorization. End Product Labeling must product be The ID:2AYIBRV001"

configurations conditions following"

Contains example a visible labeled certain cannot laptop these with final met area

(for FCC the be or in by regarding to end Manual Information to the End User The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF module in the users manual of the end product which integrates this module. The end user manual shall include all required regulatory information/warning as show in this manual. Integration instructions for host product manufacturers according to KDB 996369 D03 OEM Manual v01 2.2 List of applicable FCC rules CFR 47 FCC PART 15 SUBPART C and SUBPART E have been investigated. It is applicable to the modular transmitter 2.3 Specific operational use conditions This module is stand-alone modular. If the end product will involve the Multiple simultaneously transmitting condition or different operational conditions for a stand-alone modular transmitter in a host, host manufacturer have to consult with module manufacturer for the installation method in end system. 2.4 Limited module procedures Not applicable 2.5 Trace antenna designs Not applicable 2.6 RF exposure considerations This equipment installed and operated with minimum distance 20cm between the radiator & your body. 2.7 Antennas This radio transmitter antenna types listed below, with the maximum permissible gain indicated. Antenna types not included in this list that have a greater than the maximum gain indicated for any type listed are strictly prohibited for use with this device. complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be Communications Commission to operate with the has been approved by Federal 2AYIBRV001 gain Model Type Connector 2400-2483.5 5150-5250 5250-5350 5470-5725 5725-5850 MHz MHz MHz MHz Peak gain ( dBi ) 2400-2483.5 MHz 2.4GWIFI 5GWIFI FPC FPC FPC

MHz 4.0dBi 4.0dBi

4.0dBi

4.0dBi 2.8 Label and compliance information The final end product must be labeled in a visible area with the following" Contains FCC ID:2AYIBRV001". 2.9 Information on test modes and additional testing requirements Host manufacturer is strongly recommended to confirm compliance with FCC requirements for the transmitter when the module is installed in the host. 2.10 Additional testing, Part 15 Subpart B disclaimer Host manufacturer is responsible for compliance of the host system with module installed with all other applicable requirements for the system such as Part 15 B.

SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: 2AYIBRV001 Label and Location Ride Vision 1 Model No.: Ride Vision 1 FCC ID: 2AYIBRV001 Size: L1.0cm*W1.0cm Label Location This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd. Page 1 of 1

CONFIDENTIALITY REQUEST for Certification Service in USA Federal Communication Commission Equipment Authorization Division, Application Processing Branch 7435 Oakland Mills Road Columbia, MD 21046 Date:<2020/12/31>

Pursuant to Paragraphs 0.457 and 0.459 of the Commissions Rules (47 C.F.R.) and Section 552(b)(4) of the Freedom of Information Act, we requests confidentiality for the following products:

FCC ID 2AYIBRV001 Model name Ride Vision 1 For the product stated above, we request that the following information be held confidential;

Exhibits Long-Term Confidentiality Short-Term Confidentiality Short-Term Confidentiality Days External Photos Internal Photos Block Diagram Schematics Test Setup Photos Users Manual Parts List Tune Up Operational Descriptions The long-term confidentiality exhibits contain our trade secrets and proprietary information that could be of benefit to our competitors. The short-term confidentiality on the basis of ensuring that business sensitive information remains confidential until the actual marketing of our new device. If you have any questions, please feel free to contact me at the address shown below. Sincerely, Name/Title Uri Lavi/CEO & Co-founder Company:

Address:

Phone:

Fax:

E-Mail:

Ride Vision LTD Galgalei Haplada 11 str, POB: 13104 Herzliya, Israel 972773621656 972773621656 ask@ride-vision.com

Galgalei Haplada 11 str, POB: 13104 Herzliya, Israel Ride Vision LTD Date: 2020/12/31 FCC ID: 2AYIBRV001 Model Number: Ride Vision 1 To:

Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD To Whom It May Concern, We, Ride Vision LTD, declare that this EUT (FCC ID: 2AYIBRV001) doesnt have Ad Hoc mode function on non-US/Canada frequencies. In addition. The frequency selection feature is disabled by firmware for devices marked to the US/Canada. For DTS part of this device, only channels 1-11 will be used in North America, Country code selection is disabled. Should you have any questions or comments regarding this matter, please have my best attention. Sincerely, Name/Title Uri Lavi/CEO & Co-founder Company:

Address:

Phone:

Fax:

E-Mail:

Ride Vision LTD Galgalei Haplada 11 str, POB: 13104 Herzliya, Israel 972773621656 972773621656 ask@ride-vision.com

Galgalei Haplada 11 str, POB: 13104 Herzliya, Israel Ride Vision LTD Federal Communications Commission Authorization and Evaluation Division Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MD 21046 To whom it may concern:

2020/12/31 We, Ride Vision LTD the undersigned, hereby authorize Eurofins Product Service GmbH to act on our behalf in all matters relating to applications for equipment authorization FCC ID: 2AYIBRV001 including the signing of all documents related to these matters. Any and all acts carried out by Eurofins Product Service GmbH on our behalf shall have the same effect as acts of our own. We also hereby certify that no party to this application is subject to a denial of benefits, including FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 862. Sincerely, Name/Title Uri Lavi/CEO & Co-founder Company:

Address:

Phone:

Fax:

E-Mail:

Ride Vision LTD Galgalei Haplada 11 str, POB: 13104 Herzliya, Israel 972773621656 972773621656 ask@ride-vision.com

Ride Vision LTD Galgalei Haplada 11 str, POB: 13104 Herzliya, Israel Module Approval Request Letter Date: 2020/12/31 To:

Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD Subjects: Module Approval Request Letter The Device, FCC ID: 2AYIBRV001, is seeking FCC authorization as a modular transmitter. The EUT meets the requirement for modular approval as detailed in FCC Public Notice DA 00-1407. Compliance to each of the requirement is described below:

(a) The radio elements must have the radio frequency circuitry be shielded. Physical/discrete and tuning capacitors may be located external to the shield, but must be on the module assembly. Yes the module with a shield. Yes.

(b) The module shall have buffered modulation/data input(s) (if such inputs are provided) to ensure that the module will comply with the requirements set out in the applicable RSS standard under conditions of excessive data rates or over-modulation.

(c) The module shall have its own power supply regulation on the module. This is to ensure that the module will comply with the requirements set out in the applicable standard regardless of the design of the power supplying circuitry in the host device which houses the module. The modular has an onboard 3.3V regulator(integrated in AP6256).

(d) The module shall comply with the provisions for external power amplifiers and antennas detailed in this standard. The equipment certification submission shall contain a detailed description of the configuration of all antennas that will be used with the module. The modular has a External antenna which comply with the antenna requirement of Section 15.203.

(e) The module shall be tested for compliance with the applicable standard in a stand-alone configuration, i.e. the module must not be inside another device during testing. The modular was tested in a standalone configuration apart from host units.

(f) The module shall comply with the Category I equipment labeling requirements and CFR 15.212(a)(1)(vi). The modular has its own FCC ID number.

(g) The module shall comply with any applicable FCC RF exposure requirement which are based on the intended use/configurations. Yes, RF cexposure evaluation performed at 20cm.

(h) The modular transmitter complies with all applicable FCC rules. Instructions for maintaining compliance are given in the user instructions. Yes If you have any questions, please feel free to contact us at the address shown below Sincerely, Name/Title Uri Lavi/CEO & Co-founder Company:

Address:

Phone:

Fax:

E-Mail:

Ride Vision LTD Galgalei Haplada 11 str, POB: 13104 Herzliya, Israel 972773621656 972773621656 ask@ride-vision.com

Ride Vision LTD Galgalei Haplada 11 str, POB: 13104 Herzliya, Israel UNII Device Declaration Letter To whom it may concern:

We have declared below featured for FCC equipment authorization, Device FCC ID: 2AYIBRV001

(1) DFS Device:

(2) Active / Passive Scanning , adhoc mode access point capability Frequency Band (MHz) 5180-5240 5190-5230 5210-5210 5745-5825 5755-5795 5775-5775 Active Scanning

(the device can transmit a probe

(beacon)) Yes Yes Yes Yes Yes Yes No No No No No No passive scanning

(where the device is can listen only with no probes) No No No No No No Yes Yes Yes Yes Yes Yes No

(3) Country code selection ability Yes If yes, pls explain how it was implemented:

Master N/A Client with Radar detection capability Client without radar detection capability, Ad Hoc Mode capability Access point capability Yes Yes Yes Yes Yes Yes No No No No No No Yes Yes Yes Yes Yes Yes No No No No No No

(4) Meet 15.202 requirement Yes No pls check below :

A master device is defined as a device operating in a mode in which it has the capability to transmit without receiving an enabling signal. In this mode it is able to select a channel and initiate a network by sending enabling signals to other devices A client device is defined as a device operating in a mode in which the transmissions of the device are under control of the master. A device in client mode is not able to initiate a network.

(5) For client devices that have software configuration control to operate in different modes (active scanning in some and passive scanning in others) in different bands (devices with multiple equipment classes or those that operate on non-DFS frequencies) or modular devices which configure the modes of operations through software, the application must provide software and operations description on how the software and / or hardware is implemented to ensure that proper operations modes cannot be modified by end user or an installer. Apply Does not apply

(If apply, pls help to provide explanation on it was implement, and how software was controlled) Should you have any questions or comments regarding this matter, please have my best attention. Sincerely,

(Signed) Name/Title Uri Lavi/CEO & Co-founder Company:

Address:

Phone:

Fax:

E-Mail:

Ride Vision LTD Galgalei Haplada 11 str, POB: 13104 Herzliya, Israel 972773621656 972773621656 ask@ride-vision.com