all | frequencies |
|
|
exhibits | applications |
---|---|---|---|---|---|
manuals |
app s | submitted / available | |||||||
---|---|---|---|---|---|---|---|---|
1 2 |
|
Users Manual 1 | Users Manual | 1.70 MiB | ||||
1 2 |
|
Users Manual 2 | Users Manual | 3.32 MiB | ||||
1 2 | Cover Letter(s) | |||||||
1 2 | External Photos | |||||||
1 2 | Internal Photos | |||||||
1 2 | Test Report | |||||||
1 2 | Test Setup Photos | |||||||
1 2 | Block Diagram | |||||||
1 2 | ID Label/Location Info |
1 2 | Users Manual 1 | Users Manual | 1.70 MiB |
CD-R/RW DRIVE SW-248B SERVICE Manual CONTENTS Specifications Cautions at Service External Part Name Necessary equipments and Specifications in needing Service(P/U replacement) Exploded Views & Part List Packing Options Block Diagram Troubleshooting Circuit Diagram Main Components Block Diagram & Pin Descriptions Electrical Parts List The design and part of this product is subject to change without prior notice for performance improvement. Resd(MAX) : 2,000~6,000KBytes/Sec(CAV 40X)
- Access time : 110ms (Random. TYPICAL)
- Buffer Capacity : 8Mbyte
- Error ratio : Mode 1: Below 10-12 Mode 2: Below 10-9
- Frequency response : 20Hz~20kHz (Lineout) 100Hz~20kHz (H/P out)
- Signal to noise ratio : 70dB(1kHz, Lineout)
- Distortion factor : 0.15% Less than(1KHz)
- Channel separation : 65dB(1kHz, Lineout) 55dB(1kHz, H/P out)
- Used laser : Semiconductor laser
- Audio Output : Line out 0.75 20%(Vrms), 47K H/P out 0.65 20%(Vrms), 33 Specifications 1. General Specifications
- Drive type : Computer built-in
- Power consumption : DC +5V, 1.5A DC +12V, 1.5A
- Dimensions : 146mm (W)X42mm (H)X184mm (L)
- Net Weight : 750g 2. Electrical Features
- Interface : ATAPI BUS(IDE)
- Data transfer rate :
Write(CD-R) : 600KBytes/Sec(4X) 1,200KBytes/Sec(8X) 1,800KBytes/Sec(12X) 2,400KBytes/Sec(16X) 3,000KBytes/Sec(20X) 3,600KBytes/Sec(24X) 4,200KBytes/Sec(28X) 4,800KBytes/Sec(32X) Write(CD-RW) : 600KBytes/Sec(4X) Write(High Speed CD-RW) : 600KBytes/Sec(4X) 1,500KBytes/Sec(10X) Cautions at Service 1. General Items 1) Be careful not to have your eyes or a part of body touch with-
laser diode at repair because this product uses laser diode. 2) Do not disassemble Pick-up at repair. If the laser diode is bad, replace the entire Pick-up. 2. Earthing cautions at handling Pick-up
- Because the laser diode in optical Pick-up is subject to get out of order due to the potential difference occurring by electricity load charged in clothes or bodies, observe the following earthing items at handling. 3) Keep away from TV or other electrical units at repair to 1) Body earthing(hand) : Be sure to wear a wrist strip prevent influence from surrounding units. 4) If you replace the parts during repair, be sure to unplug the with one side earthed.(Impedance : Below 104). It removes the electricity formed in body. 2) Work table earthing : Put the earthed conductive plate
(Impedance : Below 104) such as copper plate on work table. 3) Cautions for clothes : Do not have any clothes touch with Pick-up because the electricity formed in clothes is destroyed easily. power cable before replacement. 5) If you insert a disc into the drive, be sure to load it corectly. 6) Because this unit can't be used by itself, surely mount it on PC (586 DMA support) and check the operations in use of private device driver floppy diskette. Refer to Instruction manual. 7) This unit has many parts with features related to safety and especially, for essential parts, the importance is indicated on circuit diagram and part list. Be certain to use the parts with same specifications at replaing these parts. 1 Electricity sensing device Some semiconductor units may be damaged easily by electricity. These elements are called as electricity sensing device(ESD) in general. For example, integrated circuit, field effect transister, semiconductor chip. The following methods have to be used to reduce the accident of element damage generated by electricity. 1) Emit all electric charges in your body through contact with earthing materail at once before handling a semiconductor factor or device including it. In other way, make use of commercial wristlet against electricity It shall be detached before power impression to the unit on testing because of shock. 2) After detaching an electrical device including ESD, it shall be placed on conductive surface such as aluminium to prevent the charge acummulation and unit exposure. 3) Utilize only the soldering iron with earthed end for ESD soldering or release 4) Make use of only anti-static soldering release unit. A soldering release unit not to be classified as antistatic may generate the enough charge to damage ESD unit. 5) Never use a Freon-propelling chemical product. It may generate the enough charge to damage ESD. 6) Untill installing ESD unit for replacement, never it from protection package.
(Most of ESD unit for replacement have lead composed of package shorted electrically by conductive foam, aluminium or similar conductive material.) 7) Contact with shassis including ESD or protection material in circuit parts just before detaching the protection material from lead of ESD unit for replacement Note : Be sure to avoid the power impression to the shassis or circuit and observe the safety instruction. 8) Minimize the body action at handling an unpacked ESD unit for replacement.
(Otherwise, an unconscious action, so to speak, friction between clothes or foot lifting from carpet floor may generate the enough charge to damage ESD unit.) Safety instructions 1) Read all safety and operational manuals before 11) Overload : Be careful that the wall outlet and operating this product 2) Keep the safety and operational manuals for future reference. 3) Observe all precations and operational instructions in or on the surface of this product. 4) Follow all operation and maintenance cautions. 5) Be sure to plug off the power cable before cleaning. Use a dry cloth to clean a dusty cover of cabinet instead of liquid or aersol cleaner. 6) Never use a attachment not to be recommended by this company. It may result in danger and damage. 7) Never use this product around water such as bathtub, washbasin, laundry machine, swimming pool or lakeside. 8) Never place this product on bed, sofa or around radiator and heater. 9) Power : Utilize the only power displayed on lebel If the power type can't be checked, call to dealer or Korea Electricity, Co, Ltd. Refer tooperate this product by battery or other power. 10) Lightning : Plug off the power cable for product protection during thunder and lightning flashes or this product is unused for a long time. 2 expanded cord is overloaded due to danger of fire and electrical shock. 12) Never insert a substance or liquid into this product. It may cause fire or shorck by contact with voltage point or short. 13) Part replacement : The service engineer has to use the parts of same specification at replacement. Otherwire, fire, shock or other dangers may be occurred. 14) Safety check : Be sure to perform the safety check at service or repair completion Importance : This product includes special impotrant parts on safety. These parts are indicated by on schematic diagram. At replacement of these parts, use the parts of same specification due to shock, fire or other dangers. Never transform the original design without permission of this company. External Part Name 1. Front Up/Down Volume Emergency Stop/Open HOLE button Earphhone jack Disc tray LED 2. Rear Sound output terminal Digital output terminal
(Optional) Master/Slave select pin Interface terminal Power terminal 3 Disassembly Diagram 4 Device Part List PART NAME ASSY DECK LOADING TRAY DISC FEEDING ETC CODE No BG97-02248A BG60-00009A BG97-02250A BG61-00203A BG66-00061A BG66-00032A BG66-00044A BG97-00789A BG31-00027A BG66-00033A BG66-00034A BG66-00062A BG66-00060A BG97-02251A BG61-00078A BG73-00012A BG73-00027A BG61-00238A BG61-00237A BG31-00025A BG61-00180A BG61-00122A BG31-00036A
BG97-02247A BG59-00017A BG63-00084A BG59-00018A BG73-00026A BG59-00019A BG61-00018A BG30-00025A BG41-00184A BG97-01729A BG66-00052A BG61-00225A BG61-20031A AH60-10145A AC60-10074A 6001-001348 6003-001260 BG69-00127A BG73-00022A BG61-00178A 3409-001138 BG63-00052A BG41-00182A
1.SCREW 1.ASSY LOADING 1.MAIN FRAME 2.GEAR TRAY 3.GEAR PULLEY 4.BELT PULLEY 5.ASSY LOADING M/T
- LOADING MOTOR
- PULLEY MOTOR 6.LEVER EJECT 7.SLIDE CAM 1.TRAY DISC 1.ASSY FEEDING 1.SUB CHASSIS 2.RUBBER-INSULATOR 3.RUBBER-INSULATOR 4.MAIN BASE M
- MAIN BASE P 5.ASSY STEP M/T 6.GUIDE PU 7.SHAFT PU R 8.MOTOR SPINDLE FFC-SPM 9. ASSY TURN TABLE TURN TABLE ABS COVER T/T ABS TURN TABLE BALL RUBBER-T/T ABS MAGNET BRKT-T/T 10.PICK-UP 11.EFFC PU 12.ASSY SLIDER STEP
- SLIDE STEP
- SPRING STEP 13.HOLDER CAM 14.SCREW 15.SCREW 16.SCREW 17.SCREW 18.PAD-DECK 19.RUBBER-DVA 20.PLA-VIB/ABSORBER
-.SWITCH DETECTOR
-.SHEET PU
-.FFC MAIN
-.OIL
-.GREASE
-.GREASE SPECFICATION
TITE M1.7*5(10)
HIPS(HG1760S) POM(F20-03) POM(F20-03) CR-70(BLK 1.3t)
RF-300CH-11440 POM(F20-03) POM(F20-03) KOCETAL(K700) ABS ( SR-0320D )
ABS(GF20%) BUTHYL 25Hs BUTHYL 25Hs SECC+POM SECC 2.0T SPS-15RF-054K, P4.5mm POM(NW-02) SUS420J2,3.0,L85.5mm RSM-2615A,DMBSPC75A 15 PIN
ADC12 SN PLATE T0.6 STEEL 2.5,11EA CR(NEO-B-6150) T1.5 SECC T1.0 SW-232B 32 PIN (P0.5),88mm
POM(NW-02) SUS 304-WPB POM(M90-44) TITE M1.7*5(5.5) TITE M2.6*6 M1.7*3.5 TITE M1.7*4.0*3.5 PORON LE-20 2T SILICON 25 SECC 2T PVC FILM 0.85T 13 PIN EP-100 KG-110 G-754 5 Disassembly and assembly Exterior and PCB disassembly Door-tray 1) Supply power to open the trayin direction of arrow A 2) Lift up the door in direction of arrow B 3) Close the trayand power off. Reference : If the traydoesn't open, push the clip3 into specified hole shown in detailed figure to open it compulsorily. Figure - Door-tray 6 Disassembly and assembly Exterior and PCB disassembly Panel-front 1) Remove 6 hooks 2) Take out the panel-frontforward. Figure - Panel-front 7 Disassembly and assembly Exterior and PCB disassembly Top-cabinet 1) Remove 4screws in the bottom 2) Lift up the top-cabinet Figure - Top-cabinet 8 Disassembly and assembly Exterior and PCB disassembly Ass'y-frame Low 1) Lift up the assy frame low Figure - Ass'y-frame Low 9 Disassembly and assembly Exterior and PCB disassembly MAIN-PCB 1) Disassemble the PICK-UP FPC in PCB. 2) Disassemble the FFCbetween Main PCB and Front PCB. 3) Disassemble the FFCbetween Main PCB and Front PCB. 4) Push 2hooksfor PCB fixing in deck. 5) Disassemble the MAIN-PCB 6) Remove soldering at motor connection wirePCB. 7) Press 2hooksfor PCB fixing in deck and Disassemble the FRONT-PCB Figure - Disassembly connector 10 Disassembly and assembly Deck disassembly Tray 1) Push 2hooks. 2) Take out the Trayin direction of arrow. Figure - Tray 11 Disassembly and assembly Deck disassembly Assy-Deck 1) Move the slide cam in left direction. 2) Remove screws. 3) Disassemble the Assy-feeding in arrow B direction with pushing the 2hooks in direction of arrow A Figure - Assy-Deck 12 Packing Diagram and Part List NO 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 ASSY CODE-NO BG69-00146A BG69-00147A BG69-00034A BG69-30305A BG46-00024A BG68-00352A BG95-50004A BG60-12001H BG39-30002A BG39-00010A BG39-42001B BG69-30307A 0203-001222 BG68-00355A BG68-50005A BG68-00296C BG68-00327A EPS T0.05 SPECIFICATION DM 3 DESCRIPTION MASTER CATON-BOX PACKING-CASE SW-224B/DOM SW-1 MANILA 240g CUSHION-SET BAG-PE S-W UTILITY MANUAL USERS ASSY-SCREW SCREW-MACHINE BAG-PE CABLE-IF CABLE-WIRE HARNESS BAG-PE TAPE-MASKING LABEL-RATING LABEL-QMS LABEL-BAR CODE LABEL-BROKEN SR 380MM 4P, 3P, N, UL2547/UL 1061 T0.05 PP-BEING SW-224B/DOM, ART PAPER ART PAPER DOM MODEL, ART PAPER ART PAPER M3 * 6 QTY 1/8EA 1EA 2EA 2EA 1EA 1EA 1EA 1EA 1EA 1EA 4EA 1EA 0.34M 1EA 1EA 1/8EA 1EA 13 Block Diagram 14 Trouble Shooting Check the power source and initial state. Is electrity of 5V and 12V normally input after the connecting the power cable ?
Y Do RL3E804, RL5E935 oscillate ?
Y Dose the voltage of the 1pin of IC502 change from 3.3V ?
Y Is electricity of 2.5V normally output from the 3pin of IC503?
Y When you transfer the PICK-UP to the outer cycle, and turn the power on, dose it move to the inner one?
Y TRAY IN / OUT ?
Y LASER DIODE ON ?
N N N N N N N Check the connection of the power short and cable. If the power of RL3E804, RL5E935 is normal when you check, replace X201, X301. If the power of ICIC502 (3pin) is normal when you check, replace IC502. If the power of IC503 (2pin) 5V is normal when you check, replace IC503. Refer to NO SLED operation Refer to Check TRAY IN / OUT Refer to check LASER DIODE ON 15 FOCUS UP / DOWN ?
Y FOCUS LOCK ?
Y DISC rotation ?
Y SPINDLE LOCK ?
Y AUDIO OUTPUT ?
Y WRITING Normall ?
NN NN N N N N Refer to FOCUS LOCK Refer to NO DISC ROTATION Refer to NO AUDIO OUTPUT Refer to NO WRITING 16 No SLED OPERATION When you transfer the pick-up to the outer cycle and turn the power on, dose the pick-up move to the inner one ?
Y The below waveform is outputted in IC301 1, 99pin ?
N N SLED operation of normal. Y If the constant of IC301 and GND, patterns when you check, replace. Y Y The below waveform is outputted in N IC401 35, 37pin ?
If the constant of IC401 and GND, patterns when you check, replace. Y Y Replace stepping Motor. 17 No Tray open / close operation Is the connector properly inserted into CN30 ?
Y When pressing the EJECT SW, does the peak value of the IC301 3Pin become 3.3V?
Y When it is in the Tray Open mode, does the IC301 6Pin show 1.65V?
Y OPEN When pressing the EJECT SW, does the IC401 Pin26 vary from 0V to the value between1.15V and 2.15V and then show 1.65V finally?
N N N Try the operation after inserting the connector to CN3 properly. Check the SW701 patterns and the welding condition.Replace it if the condition is normal. Check the SW701 Open and Close patterns and the welding condition. Replace it if the condition is normal. N Check the condition and patterns of R409, R410.If they are normal, N replace IC401. N Y CLOSE When pressing the EJECT SW, does the IC401 Pin26 vary from 1.65V to the value between 1.15V and 2.15V and then show 0V finally?
Y Is the Tray Motor able to output the Pin49 and 50 of IC401?
Y Y Replace TRAY MOTER. 18 No LASER DIODE ON Is the connector inserted normally into the CN10?
Y Isnt there any problem with the FPC Wire ?
Y When the SLED is moved to the inner circle, is electricity of about 1.65V output from the 80pin of IC101 ?
Y Is electricity of about 1.65V input through 71pin of CN101 ?
Y Replace PICK -UP. N N N N Try again after a normal insertion of the connector into CN10. Try again after replace of FPC Wire. If the pattern of IC101 and sodering is normal when you checked, replace IC301. If the time transfer 71pin of IC101 and soldering are ok is when you checked replace IC101 The value of voltage can be modified slightly, depending on the result of power calibration or the media. 19 No FOCUS LOCK Y FOCUS UP / DOWN ?
N Dose the S-curve below come out of the 76(TP:FE)pin of IC101after insertion of a disc ?
N If the power of IC101 and GND, soldering is normal when you check, replace IC101. N The below waveform(CH B) is outputted in IC201 132pin ?
N If the power of IC201 and GND, soldering is normal when you check, replace IC401. CH 2 : Focus Up / Down FE CH 3 : S curve CH 4 : Focus Servo On Y Is the waveform above input through the 128pin of IC201 ?
N If the power of IC201 and GND, constant is normal when you check, replace IC201. Y If the power of IC201 and GND, soldering is normal when you check, replace IC201. Y The below waveform(CH B) is outputted in ICIC401 45, 46pin ?
1. Try again after a normal insertion of the N 1. Is the FPC Wire inserted normally connector into FPC Wire. 2. Try again after replace of FPC Wire. into the CN10?
2. Isnt the FPC wire disconnected ?
Y Y Replace Pick-up. 20 No SPINDLE MOTOR ROTATION Is the waveform below output through 140pin of IC201 ?
N N If the power of IC201 and patterns, soldering is normal when you check, replace IC201. Y Y Y Is the waveform above input through 24pin of IC401 ?
N If the power of IC401 and patterns, soldering is normal when you check, replace IC401. Y Y Does output but spindle Motor rotate ?
NN Replace MOTOR. 21 No AUDIO OUTPUT Replay of AUDIO after insertion of AUDIO DISC ?
Y Is the audio output from the 164, 167pin of IC201 ?
Y Is the audio output from the 11, 13pin of CN30 ?
Y Is the audio input from the JK701 ?
Y Check the connection of the JK701 is and normal when you checked, replace JK701. N N N If the power of IC401, GND, soldering is normal when you check, replace IC200. Check the connection of the CN30 is and normal when you checked, replace VR701. Replace FRONT PCB 22 No WRITING Was the Power Calibration executed properly?
Y N Can WLT216B.EXE be executed properly?
N Replace P/UP or the entire MECHA. Y When you try to write the records again,does it work properly?
N When writing the records,does the voltage at the PIN 20 (XWGATE) of CN10 decrease from 5V to 0V?
N Check the condition of the power at CN10, GND and the welded part. If they are normal, replace IC101. Y 23 Circuit Diagram Main 24 Circuit Diagram Front 25
1 2 | Users Manual 2 | Users Manual | 3.32 MiB |
Main Components Block Diagram and Pin Descrition RL3E804 26 RL3E804 27 RL3E804 28 RL3E804
29 RL3E804 30 RL3E804
31 RL3E804 32 RL3E804 33 RL3E804 34 RL3E804 35 RL3E804 36 RL3E804 37 RL3E804 38 RL3E804 39 RL3E804 40 Pin Functions in Each Operating Mode Pin No. TFP-100B FP-100A 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 Mode 4 P12/TIOCC0/
TCLKA/A22 P13/TIOCD0/
TCLKB/A23 P14/TIOCA1 P15/TIOCB1/
TCLKC P16/TIOCA2 P17/TIOCB2/
TCLKD VSS P30/TxD0 P31/TxD1 P32/RxD0 P33/RxD1 P34/SCK0/IRQ4 P35/SCK1/IRQ5 PE0/D0 PE1/D1 PE2/D2 PE3/D3 VSS PE4/D4 PE5/D5 PE6/D6 PE7/D7 D8 D9 D10 D11 D12 D13 D14 D15 VSS A0 A1 A2 A3 A4 A5 A6 A7 VCC A8 A9 A10 A11 A12 A13 A14 A15 Mode 5 P12/TIOCC0/
TCLKA/A22 P13/TIOCD0/
TCLKB/A23 P14/TIOCA1 P15/TIOCB1/
TCLKC P16/TIOCA2 P17/TIOCB2/
TCLKD VSS P30/TxD0 P31/TxD1 P32/RxD0 P33/RxD1 P34/SCK0/IRQ4 P35/SCK1/IRQ5 PE0/D0 PE1/D1 PE2/D2 PE3/D3 VSS PE4/D4 PE5/D5 PE6/D6 PE7/D7 D8 D9 D10 D11 D12 D13 D14 D15 VSS A0 A1 A2 A3 A4 A5 A6 A7 VCC A8 A9 A10 A11 A12 A13 A14 A15 Pin Name Mode 6 *1 P12/TIOCC0/
TCLKA/A22 P13/TIOCD0/
TCLKB/A23 P14/TIOCA1 P15/TIOCB1/
TCLKC P16/TIOCA2 P17/TIOCB2/
TCLKD VSS P30/TxD0 P31/TxD1 P32/RxD0 P33/RxD1 P34/SCK0/IRQ4 P35/SCK1/IRQ5 PE0/D0 PE1/D1 PE2/D2 PE3/D3 VSS PE4/D4 PE5/D5 PE6/D6 PE7/D7 D8 D9 D10 D11 D12 D13 D14 D15 VSS PC0/A0 PC1/A1 PC2/A2 PC3/A3 PC4/A4 PC5/A5 PC6/A6 PC7/A7 VCC PB0/A8 PB1/A9 PB2/A10 PB3/A11 PB4/A12 PB5/A13 PB6/A14 PB7/A15 41 Mode 7 *1 P12/TIOCC0/
TCLKA P13/TIOCD0/
TCLKB P14/TIOCA1 P15/TIOCB1/
TCLKC P16/TIOCA2 P17/TIOCB2/
TCLKD VSS P30/TxD0 P31/TxD1 P32/RxD0 P33/RxD1 P34/SCK0/IRQ4 P35/SCK1/IRQ5 PE0 PE1 PE2 PE3 VSS PE4 PE5 PE6 PE7 PD0 PD1 PD2 PD3 PD4 PD5 PD6 PD7 VSS PC0 PC1 PC2 PC3 PC4 PC5 PC6 PC7 VCC PB0 PB1 PB2 PB3 PB4 PB5 PB6 PB7 Flash Memory Programmer Mode *2 NC NC NC NC NC NC VSS NC NC NC NC NC NC NC NC NC NC VSS NC NC NC NC FO0 FO1 FO2 FO3 FO4 FO5 FO6 FO7 VSS A0 A1 A2 A3 A4 A5 A6 A7 VCC A8 A9 A10 A11 A12 A13 A14 A15 Pin Functions in Each Operating Mode Pin No. TFP-100B FP-100A 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 Mode 4 VSS A16 A17 A18 A19 P20/TIOCA3 P21/TIOCB3 P22/TIOCC3/
TMRI0 MD0 MD1 P23/TIOCD3/
TMCI0 WDTOVF
(FWE, EMLE)*3 MD2 RES NMI STBY VCC XTAL EXTAL VSS PF7/
PF6/AS RD HWR PF3/LWR/IRQ3 PF2/WAIT/
IRQ2/DREQO PF1/BACK/
IRQ1/CS5 PF0/BREQ/
IRQ0/CS4 AVCC Vref P40/AN0 P41/AN1 P42/AN2 P43/AN3 P44/AN4 P45/AN5 P46/AN6/DA0 P47/AN7/DA1 AVSS VSS P24/TIOCA4/
TMRI1 P25/TIOCB4/
TMCI1 P26/TIOCA5/
TMO0 Mode 5 VSS A16 A17 A18 A19 P20/TIOCA3 P21/TIOCB3 P22/TIOCC3/
TMRI0 MD0 MD1 P23/TIOCD3/
TMCI0 WDTOVF
(FWE, EMLE)*3 MD2 RES NMI STBY VCC XTAL EXTAL VSS PF7/
PF6/AS RD HWR PF3/LWR/IRQ3 PF2/WAIT/
IRQ2/DREQO PF1/BACK/
IRQ1/CS5 PF0/BREQ/
IRQ0/CS4 AVCC Vref P40/AN0 P41/AN1 P42/AN2 P43/AN3 P44/AN4 P45/AN5 P46/AN6/DA0 P47/AN7/DA1 AVSS VSS P24/TIOCA4/
TMRI1 P25/TIOCB4/
TMCI1 P26/TIOCA5/
TMO0 Pin Name Mode 6 * 1 VSS PA0/A16 PA1/A17 PA2/A18 PA3/A19 P20/TIOCA3 P21/TIOCB3 P22/TIOCC3/
TMRI0 MD0 MD1 P23/TIOCD3/
TMCI0 WDTOVF
(FWE, EMLE)*3 MD2 RES NMI STBY VCC XTAL EXTAL VSS PF7/
PF6/AS RD HWR PF3/LWR/IRQ3 PF2/WAIT/
IRQ2/DREQO PF1/BACK/
IRQ1/CS5 PF0/BREQ/
IRQ0/CS4 AVCC Vref P40/AN0 P41/AN1 P42/AN2 P43/AN3 P44/AN4 P45/AN5 P46/AN6/DA0 P47/AN7/DA1 AVSS VSS P24/TIOCA4/
TMRI1 P25/TIOCB4/
TMCI1 P26/TIOCA5/
TMO0 42 Mode 7 * 1 VSS PA0 PA1 PA2 PA3 P20/TIOCA3 P21/TIOCB3 P22/TIOCC3/
TMRI0 MD0 MD1 P23/TIOCD3/
TMCI0 WDTOVF
(FWE, EMLE)*3 MD2 RES NMI STBY VCC XTAL EXTAL VSS PF7/
PF6 PF5 PF4 PF3/IRQ3 PF2/IRQ2 PF1/IRQ1 PF0/IRQ0 AVCC Vref P40/AN0 P41/AN1 P42/AN2 P43/AN3 P44/AN4 P45/AN5 P46/AN6/DA0 P47/AN7/DA1 AVSS VSS P24/TIOCA4/
TMRI1 P25/TIOCB4/
TMCI1 P26/TIOCA5/
TMO0 Flash Memory Programmer Mode * 2 VSS A16 A17 A18 NC OE CE WE VSS VSS VCC FWE VSS RES VCC VCC VCC XTAL EXTAL VSS NC NC NC NC NC VCC VSS VSS VCC VCC NC NC NC NC NC NC NC NC VSS VSS NC VSS NC Pin Functions in Each Operating Mode Pin No. TFP-100B FP-100A 92 93 94 95 96 97 98 99 100 94 95 96 97 98 99 100 1 2 Mode 4 Mode 5 P27/TIOCB5/
TMO1 PG0/IRQ6/
ADTRG PG1/CS3/
IRQ7/CS6 PG2/CS2 PG3/CS1/CS7 PG4/CS0 VCC P10/TIOCA0/A20 P11/TIOCB0/A21 P27/TIOCB5/
TMO1 PG0/IRQ6/
ADTRG PG1/CS3/
IRQ7/CS6 PG2/CS2 PG3/CS1/CS7 PG4/CS0 VCC P10/TIOCA0/A20 P11/TIOCB0/A21 Pin Name Mode 6 * 1 P27/TIOCB5/
TMO1 PG0/IRQ6/
ADTRG PG1/CS3/
IRQ7/CS6 PG2/CS2 PG3/CS1/CS7 PG4/CS0 VCC P10/TIOCA0/A20 P11/TIOCB0/A21 Mode 7 * 1 P27/TIOCB5/
TMO1 PG0/IRQ6/
ADTRG PG1/IRQ7 PG2 PG3 PG4 VCC P10/TIOCA0 P11/TIOCB0 Flash Memory Programmer Mode * 2 NC NC NC NC NC NC VCC NC NC Notes : 1. Only modes 4 and 5 are available on the ROMless version. 2. Flash memory programmer mode information is preliminary. 3. The FWE pin function is only available on the H8S/2318 F-ZTAT and H8S/2315 F-ZTAT versions. The EMLE pin function is only available on the H8S/2319 F-ZTAT version. It cannot be used as a WDTOVF pin on the F-ZTAT version. 43 BD7902CFS 44 BD7902CFS Pin Descriptions Terminal Symbol Terminal Function Terminal Symbol Terminal Function 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 HU+
HU-
HV+
HV-
HW+
HW-
HB Hall amp.U positive input Hall amp.U negative input Hall amp.U positive input Hall amp.U negative input Hall amp.U positive input Hall amp.U negative input Hall bias PGND1 Spindle driver power ground1 U Spindle driver output U SPVM1 Spindle driver power supply1 V GND GND GND GND GND Spindle driver output V GND GND GND GND GND PGND2 Spindle driver power ground 2 W Spindle driver output W SPVM2 Spindle driver power supply 2 SPRNF Spindle driver ourrent sense FG CTL1 CTL2 SPIN Frequency generator output Driver logic control input1 Driver logic control input2 Spindle driver input DGND PWM block pre-ground LDIN VC Loading driver input Reference voltage input 54 53 52 51 50 49 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 32 31 30 29 28 45 DVCC PWM block control power supply FCIN TKIN VCC LDO+
LDO-
TKO+
TKO-
FCO+
FCO-
AVM GND GND GND GND GND AGND SLO1+
SLO1-
SLO2+
SLO2-
Focus driver input Tracking driver input BTL pre and Loading power supply Loading driver positive output Loading driver negative output Tracking driver positive output Tracking driver negative output Focus driver positive output Focus driver negative output Actuator driver block power supply GND GND GND GND GND Ground Sled drive 1 positive output Sled drive 1 negative output Sled drive 2 positive output Sled drive 2 negative output SLGND Sled driver power ground SLRNF2 Sled driver 2 current sense SLRNF1 Sled driver 1 current sense SLVDD Sled driver PowerMos pre-supply SLIN2 SLIN1 Sled driver 2 input Sled driver 1 input Electrical Parts List LOC B501 B502 B503 B504 B505 C101 C102 C103 C104 C105 C106 C107 C108 C109 C110 C111 C112 C113 C114 C115 C116 C117 C118 C119 C120 C122 C123 C124 C126 C127 C128 C129 C131 C133 C135 C136 C137 C138 C139 C140 C141 C142 C143 C144 C145 C146 C148 C149 C150 C151 C199 C201 CODE NO 3301-001082 3301-001082 3301-001082 3301-001082 3301-001082 2203-000888 2203-000972 2203-000236 2203-001724 2203-000440 2203-000888 2203-000888 2203-001607 2203-000783 2203-001656 2404-001020 2203-000189 2402-000136 2203-000257 2203-001630 2203-000189 2203-002398 2203-000257 2203-000257 2402-000112 2203-000440 2203-000440 2402-000112 2203-000236 2203-001724 2203-000236 2203-000236 2404-001020 2404-001020 2203-000357 2203-000357 2203-000783 2203-000189 2404-001131 2203-000189 2404-001131 2203-000531 2203-005065 2203-001724 2203-001598 2203-000189 2203-000189 2203-000189 2203-001402 2203-001126 2203-001086 2203-000257 DESCRIPTION CORE-FERRITE BEAD;AB,60OHM,3.2X2.5X1.3MM CORE-FERRITE BEAD;AB,60OHM,3.2X2.5X1.3MM CORE-FERRITE BEAD;AB,60OHM,3.2X2.5X1.3MM CORE-FERRITE BEAD;AB,60OHM,3.2X2.5X1.3MM CORE-FERRITE BEAD;AB,60OHM,3.2X2.5X1.3MM C-CERAMIC,CHIP;4.7nF,10%,50V,X7R,TP,1608 C-CERAMIC,CHIP;47nF,10%,16V,X7R,TP,1608 C-CERAMIC,CHIP;0.1nF,5%,50V,NP0,TP,1608 C-CERAMIC,CHIP;4700NF,+80-20%,16V,Y5V,TP C-CERAMIC,CHIP;1nF,10%,50V,X7R,TP,1608,-
C-CERAMIC,CHIP;4.7nF,10%,50V,X7R,TP,1608 C-CERAMIC,CHIP;4.7nF,10%,50V,X7R,TP,1608 C-CERAMIC,CHIP;0.22nF,5%,50V,NP0,TP,1608 C-CERAMIC,CHIP;0.33nF,5%,50V,NP0,TP,1608 C-CERAMIC,CHIP;0.47nF,5%,50V,NP0,TP,1608 C-TA,CHIP;10uF,20%,10V,GP,TP,3216,3.2 C-CERAMIC,CHIP;100nF,+80-20%,25V,Y5V,TP, C-AL,SMD;22uF,20%,16V,GP,TP,5.3x5.3x5.2 C-CERAMIC,CHIP;10nF,10%,50V,X7R,TP,1608 C-CERAMIC,CHIP;330nF,+80-20%,16V,Y5V,TP, C-CERAMIC,CHIP;100nF,+80-20%,25V,Y5V,TP, C-CERAMIC,CHIP;22nF,10%,50V,X7R,TP,1608 C-CERAMIC,CHIP;10nF,10%,50V,X7R,TP,1608 C-CERAMIC,CHIP;10nF,10%,50V,X7R,TP,1608 C-AL,SMD;10uF,20%,16V,GP,TP,3.3x3.3x5.4 C-CERAMIC,CHIP;1nF,10%,50V,X7R,TP,1608,-
C-CERAMIC,CHIP;1nF,10%,50V,X7R,TP,1608,-
C-AL,SMD;10uF,20%,16V,GP,TP,3.3x3.3x5.4 C-CERAMIC,CHIP;0.1nF,5%,50V,NP0,TP,1608 C-CERAMIC,CHIP;4700NF,+80-20%,16V,Y5V,TP C-CERAMIC,CHIP;0.1nF,5%,50V,NP0,TP,1608 C-CERAMIC,CHIP;0.1nF,5%,50V,NP0,TP,1608 C-TA,CHIP;10uF,20%,10V,GP,TP,3216,3.2 C-TA,CHIP;10uF,20%,10V,GP,TP,3216,3.2 C-CERAMIC,CHIP;0.15nF,5%,50V,NP0,TP,1608 C-CERAMIC,CHIP;0.15nF,5%,50V,NP0,TP,1608 C-CERAMIC,CHIP;0.33nF,5%,50V,NP0,TP,1608 C-CERAMIC,CHIP;100nF,+80-20%,25V,Y5V,TP, C-TA,CHIP;22UF,10%,10V,GP,TP,3528 C-CERAMIC,CHIP;100nF,+80-20%,25V,Y5V,TP, C-TA,CHIP;22UF,10%,10V,GP,TP,3528 C-CERAMIC,CHIP;2.7nF,10%,50V,X7R,TP,1608 C-CERAMIC,CHIP;1000nF,+80-20%,10V,Y5V,TP C-CERAMIC,CHIP;4700NF,+80-20%,16V,Y5V,TP C-CERAMIC,CHIP;2200nF,+80-20%,16V,Y5V,TP C-CERAMIC,CHIP;100nF,+80-20%,25V,Y5V,TP, C-CERAMIC,CHIP;100nF,+80-20%,25V,Y5V,TP, C-CERAMIC,CHIP;100nF,+80-20%,25V,Y5V,TP, C-CERAMIC,CHIP;220nF,+80-20%,16V,Y5V,TP, C-CERAMIC,CHIP;0.68nF,10%,50V,X7R,TP,160 C-CERAMIC,CHIP;0.005nF,0.25pF,50V,NP0,TP C-CERAMIC,CHIP;10nF,10%,50V,X7R,TP,1608 46 Electrical Parts List LOC C202 C203 C204 C205 C206 C207 C208 C209 C210 C211 C212 C213 C214 C215 C216 C217 C218 C220 C221 C223 C224 C225 C226 C227 C228 C229 C230 C231 C232 C233 C234 C235 C236 C237 C238 C240 C241 C242 C243 C244 C245 C246 C247 C248 C249 C250 C251 C301 C302 C303 C304 C305 C306 C307 C308 C309 C310 CODE NO 2203-000257 2203-000257 2203-000257 2203-000257 2203-000257 2203-001103 2203-005342 2203-002085 2404-001020 2203-000189 2203-000041 2203-000041 2203-000041 2203-000041 2203-000257 2203-000236 2203-000189 2203-000257 2203-001724 2203-000189 2203-000257 2203-002398 2203-000440 2203-000783 2203-001052 2203-000783 2203-000189 2203-000372 2203-000372 2203-000972 2203-000257 2203-000041 2203-000041 2404-001020 2404-001020 2203-001724 2203-000189 2203-000257 2203-001598 2203-000257 2404-001020 2404-001020 2203-000140 2203-000140 2203-000257 2203-000257 2404-001020 2203-001683 2203-001656 2203-001598 2203-000783 2203-000257 2203-000041 2203-000041 2203-000257 2203-001607 2203-000715 DESCRIPTION C-CERAMIC,CHIP;10nF,10%,50V,X7R,TP,1608 C-CERAMIC,CHIP;10nF,10%,50V,X7R,TP,1608 C-CERAMIC,CHIP;10nF,10%,50V,X7R,TP,1608 C-CERAMIC,CHIP;10nF,10%,50V,X7R,TP,1608 C-CERAMIC,CHIP;10nF,10%,50V,X7R,TP,1608 C-CERAMIC,CHIP;6.8nF,10%,50V,X7R,TP,1608 C-CERAMIC,CHIP;82nF,10%,16V,X7R,TP,1608 C-CERAMIC,CHIP;56nF,10%,50V,X7R,TP,2012, C-TA,CHIP;10uF,20%,10V,GP,TP,3216,3.2 C-CERAMIC,CHIP;100nF,+80-20%,25V,Y5V,TP, C-CERAMIC,CHIP;0.01nF,0.25pF,50V,NP0,TP, C-CERAMIC,CHIP;0.01nF,0.25pF,50V,NP0,TP, C-CERAMIC,CHIP;0.01nF,0.25pF,50V,NP0,TP, C-CERAMIC,CHIP;0.01nF,0.25pF,50V,NP0,TP, C-CERAMIC,CHIP;10nF,10%,50V,X7R,TP,1608 C-CERAMIC,CHIP;0.1nF,5%,50V,NP0,TP,1608 C-CERAMIC,CHIP;100nF,+80-20%,25V,Y5V,TP, C-CERAMIC,CHIP;10nF,10%,50V,X7R,TP,1608 C-CERAMIC,CHIP;4700NF,+80-20%,16V,Y5V,TP C-CERAMIC,CHIP;100nF,+80-20%,25V,Y5V,TP, C-CERAMIC,CHIP;10nF,10%,50V,X7R,TP,1608 C-CERAMIC,CHIP;22nF,10%,50V,X7R,TP,1608 C-CERAMIC,CHIP;1nF,10%,50V,X7R,TP,1608,-
C-CERAMIC,CHIP;0.33nF,5%,50V,NP0,TP,1608 C-CERAMIC,CHIP;0.56nF,10%,50V,X7R,TP,160 C-CERAMIC,CHIP;0.33nF,5%,50V,NP0,TP,1608 C-CERAMIC,CHIP;100nF,+80-20%,25V,Y5V,TP, C-CERAMIC,CHIP;15nF,10%,50V,X7R,TP,1608, C-CERAMIC,CHIP;15nF,10%,50V,X7R,TP,1608, C-CERAMIC,CHIP;47nF,10%,16V,X7R,TP,1608 C-CERAMIC,CHIP;10nF,10%,50V,X7R,TP,1608 C-CERAMIC,CHIP;0.01nF,0.25pF,50V,NP0,TP, C-CERAMIC,CHIP;0.01nF,0.25pF,50V,NP0,TP, C-TA,CHIP;10uF,20%,10V,GP,TP,3216,3.2 C-TA,CHIP;10uF,20%,10V,GP,TP,3216,3.2 C-CERAMIC,CHIP;4700NF,+80-20%,16V,Y5V,TP C-CERAMIC,CHIP;100nF,+80-20%,25V,Y5V,TP, C-CERAMIC,CHIP;10nF,10%,50V,X7R,TP,1608 C-CERAMIC,CHIP;2200nF,+80-20%,16V,Y5V,TP C-CERAMIC,CHIP;10nF,10%,50V,X7R,TP,1608 C-TA,CHIP;10uF,20%,10V,GP,TP,3216,3.2 C-TA,CHIP;10uF,20%,10V,GP,TP,3216,3.2 C-CERAMIC,CHIP;1.5nF,10%,50V,X7R,TP,1608 C-CERAMIC,CHIP;1.5nF,10%,50V,X7R,TP,1608 C-CERAMIC,CHIP;10nF,10%,50V,X7R,TP,1608 C-CERAMIC,CHIP;10nF,10%,50V,X7R,TP,1608 C-TA,CHIP;10uF,20%,10V,GP,TP,3216,3.2 C-CERAMIC,CHIP;0.068nF,5%,50V,NP0,TP,160 C-CERAMIC,CHIP;0.47nF,5%,50V,NP0,TP,1608 C-CERAMIC,CHIP;2200nF,+80-20%,16V,Y5V,TP C-CERAMIC,CHIP;0.33nF,5%,50V,NP0,TP,1608 C-CERAMIC,CHIP;10nF,10%,50V,X7R,TP,1608 C-CERAMIC,CHIP;0.01nF,0.25pF,50V,NP0,TP, C-CERAMIC,CHIP;0.01nF,0.25pF,50V,NP0,TP, C-CERAMIC,CHIP;10nF,10%,50V,X7R,TP,1608 C-CERAMIC,CHIP;0.22nF,5%,50V,NP0,TP,1608 C-CERAMIC,CHIP;3.3nF,10%,50V,X7R,TP,1608 47 Electrical Parts List LOC C311 C312 C313 C314 C315 C316 C317 C318 C319 C320 C321 C322 C323 C324 C401 C402 C403 C405 C406 C407 C408 C409 C410 C411 C412 C413 C414 C419 C501 C502 C503 C504 C505 C506 C507 C508 C509 C510 C511 C512 C513 C514 C515 C516 CN30 CN40 D501 IC102 IC202B IC203 IC402 IC501 JP101 JP201 JP211 Q101 Q501 CODE NO 2203-000783 2203-000783 2203-000140 2203-000815 2203-000888 2203-000783 2203-000189 2203-000189 2203-001607 2203-001607 2203-000257 2203-000783 2203-000041 2203-001724 2402-001042 2203-000189 2203-001598 2203-001598 2203-000888 2203-000888 2203-000189 2402-001042 2203-000189 2203-000189 2203-000189 2203-000189 2203-000189 2203-000189 2203-000189 2203-000189 2402-001042 2203-000189 2203-001724 2402-001042 2203-000189 2203-000189 2203-000189 2203-000140 2203-001724 2203-000257 2203-000257 2203-000189 2404-001270 2203-000189 3708-001524 3708-001606 0407-000123 1002-001262 1105-001261 0801-002414 1201-001001 1203-001394 2007-000070 2007-000070 2007-000070 0504-000110 0504-000110 DESCRIPTION C-CERAMIC,CHIP;0.33nF,5%,50V,NP0,TP,1608 C-CERAMIC,CHIP;0.33nF,5%,50V,NP0,TP,1608 C-CERAMIC,CHIP;1.5nF,10%,50V,X7R,TP,1608 C-CERAMIC,CHIP;0.033nF,5%,50V,NP0,TP,160 C-CERAMIC,CHIP;4.7nF,10%,50V,X7R,TP,1608 C-CERAMIC,CHIP;0.33nF,5%,50V,NP0,TP,1608 C-CERAMIC,CHIP;100nF,+80-20%,25V,Y5V,TP, C-CERAMIC,CHIP;100nF,+80-20%,25V,Y5V,TP, C-CERAMIC,CHIP;0.22nF,5%,50V,NP0,TP,1608 C-CERAMIC,CHIP;0.22nF,5%,50V,NP0,TP,1608 C-CERAMIC,CHIP;10nF,10%,50V,X7R,TP,1608 C-CERAMIC,CHIP;0.33nF,5%,50V,NP0,TP,1608 C-CERAMIC,CHIP;0.01nF,0.25pF,50V,NP0,TP, C-CERAMIC,CHIP;4700NF,+80-20%,16V,Y5V,TP C-AL,SMD;100uF,20%,16V,GP,TP,6.6x6.6x5. C-CERAMIC,CHIP;100nF,+80-20%,25V,Y5V,TP, C-CERAMIC,CHIP;2200nF,+80-20%,16V,Y5V,TP C-CERAMIC,CHIP;2200nF,+80-20%,16V,Y5V,TP C-CERAMIC,CHIP;4.7nF,10%,50V,X7R,TP,1608 C-CERAMIC,CHIP;4.7nF,10%,50V,X7R,TP,1608 C-CERAMIC,CHIP;100nF,+80-20%,25V,Y5V,TP, C-AL,SMD;100uF,20%,16V,GP,TP,6.6x6.6x5. C-CERAMIC,CHIP;100nF,+80-20%,25V,Y5V,TP, C-CERAMIC,CHIP;100nF,+80-20%,25V,Y5V,TP, C-CERAMIC,CHIP;100nF,+80-20%,25V,Y5V,TP, C-CERAMIC,CHIP;100nF,+80-20%,25V,Y5V,TP, C-CERAMIC,CHIP;100nF,+80-20%,25V,Y5V,TP, C-CERAMIC,CHIP;100nF,+80-20%,25V,Y5V,TP, C-CERAMIC,CHIP;100nF,+80-20%,25V,Y5V,TP, C-CERAMIC,CHIP;100nF,+80-20%,25V,Y5V,TP, C-AL,SMD;100uF,20%,16V,GP,TP,6.6x6.6x5. C-CERAMIC,CHIP;100nF,+80-20%,25V,Y5V,TP, C-CERAMIC,CHIP;4700NF,+80-20%,16V,Y5V,TP C-AL,SMD;100uF,20%,16V,GP,TP,6.6x6.6x5. C-CERAMIC,CHIP;100nF,+80-20%,25V,Y5V,TP, C-CERAMIC,CHIP;100nF,+80-20%,25V,Y5V,TP, C-CERAMIC,CHIP;100nF,+80-20%,25V,Y5V,TP, C-CERAMIC,CHIP;1.5nF,10%,50V,X7R,TP,1608 C-CERAMIC,CHIP;4700NF,+80-20%,16V,Y5V,TP C-CERAMIC,CHIP;10nF,10%,50V,X7R,TP,1608 C-CERAMIC,CHIP;10nF,10%,50V,X7R,TP,1608 C-CERAMIC,CHIP;100nF,+80-20%,25V,Y5V,TP, C-TA,CHIP;47UF,20%,10V,-,TP,3216 C-CERAMIC,CHIP;100nF,+80-20%,25V,Y5V,TP, CONNECTOR-FPC/FFC/PIC;13P,1mm,SMD-A,SN CONNECTOR-FPC/FFC/PIC;15P,1MM,SMD-A,SN DIODE-ARRAY;DAN202K,80V,100MA,CA2-3,SOT-
IC-D/A CONVERTER;BU2505FV,10BIT,SOIC,20P IC-DRAM;12L1616A,16BIT,TSOP,50P,400MIL IC-CMOS LOGIC;7W53,MULTI/DEMULTIPLEXER,S IC-OP AMP;2100,SOP,8P,250MIL,DUAL,80mV/V IC-VOL. DETECTOR;9735,SOT-23,3P,-,PLASTI R-CHIP;0ohm,5%,1/16W,DA,TP,1608 R-CHIP;0ohm,5%,1/16W,DA,TP,1608 R-CHIP;0ohm,5%,1/16W,DA,TP,1608 TR-DIGITAL;DTC114EU,NPN,200MW,10K/10K,SC TR-DIGITAL;DTC114EU,NPN,200MW,10K/10K,SC 48 Electrical Parts List LOC Q502 Q503 Q504 R101 R102 R103 R106 R107 R109 R110 R111 R112 R113 R114 R115 R116 R117 R118 R119 R120 R121 R122 R201 R202 R203 R204 R205 R206 R207 R208 R209 R210 R212 R213 R214 R215 R216 R217 R218 R220 R222 R223 R224 R226 R227 R228 R229 R230 R231 R232 R233 R234 R235 R236 R237 R238 R239 CODE NO 0504-000110 0504-000105 0504-000105 2007-000669 2007-000109 2007-000074 2007-000102 2007-000090 2007-000076 2007-000090 2007-001179 2007-000134 2007-000134 2007-000067 2007-000090 2007-000084 2007-000070 2007-000070 2007-001002 2007-001044 2007-000071 2007-000071 2007-000115 2007-000071 2007-000071 2007-000115 2007-000071 2007-000115 2007-000115 2007-000071 2007-000115 2007-000070 2007-000074 2007-000074 2007-000512 2007-000076 2007-000113 2007-000116 2007-000882 2007-000708 2007-000772 2007-000772 2007-000772 2007-000060 2007-000583 2007-001206 2007-000090 2007-000090 2007-000133 2007-000090 2007-000092 2007-000090 2007-000084 2007-000431 2007-000109 2007-000070 2007-000312 DESCRIPTION TR-DIGITAL;DTC114EU,NPN,200MW,10K/10K,SC TR-DIGITAL;DTA114EU,PNP,200MW,10K/10K,SC TR-DIGITAL;DTA114EU,PNP,200MW,10K/10K,SC R-CHIP;2Kohm,1%,1/16W,DA,TP,1608 R-CHIP;1Mohm,5%,1/16W,DA,TP,1608 R-CHIP;100ohm,5%,1/16W,DA,TP,1608 R-CHIP;100Kohm,5%,1/16W,DA,TP,1608 R-CHIP;10KOHM,5%,1/16W,DA,TP,1608 R-CHIP;330ohm,5%,1/16W,DA,TP,1608 R-CHIP;10KOHM,5%,1/16W,DA,TP,1608 R-CHIP;8.2Kohm,5%,1/16W,DA,TP,1608 R-CHIP;33Kohm,5%,1/16W,DA,TP,1608 R-CHIP;33Kohm,5%,1/16W,DA,TP,1608 R-CHIP;15Kohm,1%,1/16W,DA,TP,1608 R-CHIP;10KOHM,5%,1/16W,DA,TP,1608 R-CHIP;4.7Kohm,5%,1/16W,DA,TP,1608 R-CHIP;0ohm,5%,1/16W,DA,TP,1608 R-CHIP;0ohm,5%,1/16W,DA,TP,1608 R-CHIP;510ohm,5%,1/16W,DA,TP,1608 R-CHIP;56ohm,5%,1/16W,DA,TP,1608 R-CHIP;22ohm,5%,1/16W,DA,TP,1608 R-CHIP;22ohm,5%,1/16W,DA,TP,1608 R-CHIP;82ohm,5%,1/16W,DA,TP,1608 R-CHIP;22ohm,5%,1/16W,DA,TP,1608 R-CHIP;22ohm,5%,1/16W,DA,TP,1608 R-CHIP;82ohm,5%,1/16W,DA,TP,1608 R-CHIP;22ohm,5%,1/16W,DA,TP,1608 R-CHIP;82ohm,5%,1/16W,DA,TP,1608 R-CHIP;82ohm,5%,1/16W,DA,TP,1608 R-CHIP;22ohm,5%,1/16W,DA,TP,1608 R-CHIP;82ohm,5%,1/16W,DA,TP,1608 R-CHIP;0ohm,5%,1/16W,DA,TP,1608 R-CHIP;100ohm,5%,1/16W,DA,TP,1608 R-CHIP;100ohm,5%,1/16W,DA,TP,1608 R-CHIP;2.4Kohm,5%,1/16W,DA,TP,1608 R-CHIP;330ohm,5%,1/16W,DA,TP,1608 R-CHIP;33ohm,5%,1/16W,DA,TP,1608 R-CHIP;120ohm,5%,1/16W,DA,TP,1608 R-CHIP;4.7ohm,5%,1/16W,DA,TP,1608 R-CHIP;3.9Kohm,1%,1/16W,DA,TP,1608 R-CHIP;33Kohm,1%,1/16W,DA,TP,1608 R-CHIP;33Kohm,1%,1/16W,DA,TP,1608 R-CHIP;33Kohm,1%,1/16W,DA,TP,1608 R-CHIP;100Kohm,1%,1/16W,DA,TP,1608 R-CHIP;22Kohm,1%,1/16W,DA,TP,1608 R-CHIP;82Kohm,1%,1/16W,DA,TP,1608 R-CHIP;10KOHM,5%,1/16W,DA,TP,1608 R-CHIP;10KOHM,5%,1/16W,DA,TP,1608 R-CHIP;330Kohm,5%,1/16W,DA,TP,1608 R-CHIP;10KOHM,5%,1/16W,DA,TP,1608 R-CHIP;15Kohm,5%,1/16W,DA,TP,1608 R-CHIP;10KOHM,5%,1/16W,DA,TP,1608 R-CHIP;4.7Kohm,5%,1/16W,DA,TP,1608 R-CHIP;16Kohm,5%,1/16W,DA,TP,1608 R-CHIP;1Mohm,5%,1/16W,DA,TP,1608 R-CHIP;0ohm,5%,1/16W,DA,TP,1608 R-CHIP;10OHM,5%,1/8W,DA,TP,3216 49 Electrical Parts List LOC R240 R241 R242 R243 R245 R246 R247 R250 R251 R301 R302 R303 R304 R305 R306 R307 R308 R309 R312 R313 R314 R315 R316 R317 R318 R319 R322 R323 R324 R325 R326 R327 R328 R329 R331 R332 R333 R334 R335 R336 R337 R338 R339 R340 R341 R342 R345 R346 R395 R396 R397 R398 R399 R401 R402 R403 R404 CODE NO 2007-000074 2007-000074 2007-000078 2007-000078 2007-000077 2007-000084 2007-000094 2007-000309 2007-000883 2007-000075 2007-001157 2007-000075 2007-000076 2007-000090 2007-000123 2007-000094 2007-000094 2007-000094 2007-000075 2007-000076 2007-000090 2007-000094 2007-000070 2007-000094 2007-000109 2007-000094 2007-000094 2007-000094 2007-000094 2007-000080 2007-000080 2007-000080 2007-000080 2007-000078 2007-000125 2007-000125 2007-000125 2007-000125 2007-000075 2007-000076 2007-000080 2007-000094 2007-000094 2007-000094 2007-000094 2007-000094 2007-000080 2007-000078 2007-000084 2007-000120 2007-000120 2007-000094 2007-000094 2007-000113 2007-000034 2007-000034 2007-000034 DESCRIPTION R-CHIP;100ohm,5%,1/16W,DA,TP,1608 R-CHIP;100ohm,5%,1/16W,DA,TP,1608 R-CHIP;1Kohm,5%,1/16W,DA,TP,1608 R-CHIP;1Kohm,5%,1/16W,DA,TP,1608 R-CHIP;470ohm,5%,1/16W,DA,TP,1608 R-CHIP;4.7Kohm,5%,1/16W,DA,TP,1608 R-CHIP;22Kohm,5%,1/16W,DA,TP,1608 R-CHIP;10ohm,5%,1/16W,DA,TP,1608 R-CHIP;4.7OHM,5%,1/8W,DA,TP,3216 R-CHIP;220ohm,5%,1/16W,DA,TP,1608 R-CHIP;750ohm,5%,1/16W,DA,TP,1608 R-CHIP;220ohm,5%,1/16W,DA,TP,1608 R-CHIP;330ohm,5%,1/16W,DA,TP,1608 R-CHIP;10KOHM,5%,1/16W,DA,TP,1608 R-CHIP;1.5Kohm,5%,1/16W,DA,TP,1608 R-CHIP;22Kohm,5%,1/16W,DA,TP,1608 R-CHIP;22Kohm,5%,1/16W,DA,TP,1608 R-CHIP;22Kohm,5%,1/16W,DA,TP,1608 R-CHIP;220ohm,5%,1/16W,DA,TP,1608 R-CHIP;330ohm,5%,1/16W,DA,TP,1608 R-CHIP;10KOHM,5%,1/16W,DA,TP,1608 R-CHIP;22Kohm,5%,1/16W,DA,TP,1608 R-CHIP;0ohm,5%,1/16W,DA,TP,1608 R-CHIP;22Kohm,5%,1/16W,DA,TP,1608 R-CHIP;1Mohm,5%,1/16W,DA,TP,1608 R-CHIP;22Kohm,5%,1/16W,DA,TP,1608 R-CHIP;22Kohm,5%,1/16W,DA,TP,1608 R-CHIP;22Kohm,5%,1/16W,DA,TP,1608 R-CHIP;22Kohm,5%,1/16W,DA,TP,1608 R-CHIP;2Kohm,5%,1/16W,DA,TP,1608 R-CHIP;2Kohm,5%,1/16W,DA,TP,1608 R-CHIP;2Kohm,5%,1/16W,DA,TP,1608 R-CHIP;2Kohm,5%,1/16W,DA,TP,1608 R-CHIP;1Kohm,5%,1/16W,DA,TP,1608 R-CHIP;3.9Kohm,5%,1/16W,DA,TP,1608 R-CHIP;3.9Kohm,5%,1/16W,DA,TP,1608 R-CHIP;3.9Kohm,5%,1/16W,DA,TP,1608 R-CHIP;3.9Kohm,5%,1/16W,DA,TP,1608 R-CHIP;220ohm,5%,1/16W,DA,TP,1608 R-CHIP;330ohm,5%,1/16W,DA,TP,1608 R-CHIP;2Kohm,5%,1/16W,DA,TP,1608 R-CHIP;22Kohm,5%,1/16W,DA,TP,1608 R-CHIP;22Kohm,5%,1/16W,DA,TP,1608 R-CHIP;22Kohm,5%,1/16W,DA,TP,1608 R-CHIP;22Kohm,5%,1/16W,DA,TP,1608 R-CHIP;22Kohm,5%,1/16W,DA,TP,1608 R-CHIP;2Kohm,5%,1/16W,DA,TP,1608 R-CHIP;1Kohm,5%,1/16W,DA,TP,1608 R-CHIP;4.7Kohm,5%,1/16W,DA,TP,1608 R-CHIP;680ohm,5%,1/16W,DA,TP,1608 R-CHIP;680ohm,5%,1/16W,DA,TP,1608 R-CHIP;22Kohm,5%,1/16W,DA,TP,1608 R-CHIP;22Kohm,5%,1/16W,DA,TP,1608 R-CHIP;33ohm,5%,1/16W,DA,TP,1608 R-CHIP;1OHM,5%,1/4W,DA,TP,3216 R-CHIP;1OHM,5%,1/4W,DA,TP,3216 R-CHIP;1OHM,5%,1/4W,DA,TP,3216 50 Electrical Parts List LOC R405 R406 R407 R408 R409 R410 R411 R412 R413 R414 R415 R416 R417 R418 R419 R420 R421 R422 R423 R424 R425 R426 R501 R502 R503 R504 R505 R506 R507 R508 RA201 CODE NO 2007-000883 2007-000094 2007-000094 2007-000094 2007-000131 2007-000131 2007-000090 2007-000090 2007-000034 2007-002749 2007-000034 2007-002749 2007-000104 2007-000092 2007-000103 2007-000134 2007-000097 2007-000125 2007-000124 2007-000103 2007-000127 2007-001134 2007-000036 2007-000036 2007-000090 2007-000090 2007-000090 2007-000094 2007-000102 2007-000102 2011-001085 DESCRIPTION R-CHIP;4.7OHM,5%,1/8W,DA,TP,3216 R-CHIP;22Kohm,5%,1/16W,DA,TP,1608 R-CHIP;22Kohm,5%,1/16W,DA,TP,1608 R-CHIP;22Kohm,5%,1/16W,DA,TP,1608 R-CHIP;91Kohm,5%,1/16W,DA,TP,1608 R-CHIP;91Kohm,5%,1/16W,DA,TP,1608 R-CHIP;10KOHM,5%,1/16W,DA,TP,1608 R-CHIP;10KOHM,5%,1/16W,DA,TP,1608 R-CHIP;1OHM,5%,1/4W,DA,TP,3216 R-CHIP;3.3OHM,5%,1/8W,DA,TP,3216 R-CHIP;1OHM,5%,1/4W,DA,TP,3216 R-CHIP;3.3OHM,5%,1/8W,DA,TP,3216 R-CHIP;150Kohm,5%,1/16W,DA,TP,1608 R-CHIP;15Kohm,5%,1/16W,DA,TP,1608 R-CHIP;120Kohm,5%,1/16W,DA,TP,1608 R-CHIP;33Kohm,5%,1/16W,DA,TP,1608 R-CHIP;47Kohm,5%,1/16W,DA,TP,1608 R-CHIP;3.9Kohm,5%,1/16W,DA,TP,1608 R-CHIP;2.2Kohm,5%,1/16W,DA,TP,1608 R-CHIP;120Kohm,5%,1/16W,DA,TP,1608 R-CHIP;9.1Kohm,5%,1/16W,DA,TP,1608 R-CHIP;68ohm,5%,1/16W,DA,TP,1608 R-CHIP;2OHM,5%,1/8W,DA,TP,3216 R-CHIP;2OHM,5%,1/8W,DA,TP,3216 R-CHIP;10KOHM,5%,1/16W,DA,TP,1608 R-CHIP;10KOHM,5%,1/16W,DA,TP,1608 R-CHIP;10KOHM,5%,1/16W,DA,TP,1608 R-CHIP;22Kohm,5%,1/16W,DA,TP,1608 R-CHIP;100Kohm,5%,1/16W,DA,TP,1608 R-CHIP;100Kohm,5%,1/16W,DA,TP,1608 R-NETWORK;82ohm,5%,63mW,L,CHIP,8P,TP 51 Samsung Electronics Co., Ltd. 01, 2002 Printed in Korea Code No.: BG68-00435A
frequency | equipment class | purpose | ||
---|---|---|---|---|
1 | 2002-09-24 | JBP - Part 15 Class B Computing Device Peripheral | Class II permissive change or modification of presently authorized equipment | |
2 | 2002-07-30 | JBP - Part 15 Class B Computing Device Peripheral | Original Equipment |
app s | Applicant Information | |||||
---|---|---|---|---|---|---|
1 2 | Effective |
2002-09-24
|
||||
1 2 |
2002-07-30
|
|||||
1 2 | Applicant's complete, legal business name |
Samsung Electronics Co Ltd
|
||||
1 2 | FCC Registration Number (FRN) |
0027908797
|
||||
1 2 | Physical Address |
19 Chapin Rd., Building D
|
||||
1 2 |
Pine Brook, New Jersey 07058
|
|||||
1 2 |
United States
|
|||||
app s | TCB Information | |||||
1 2 | TCB Application Email Address |
r******@pctestlab.com
|
||||
1 2 |
r******@pctestlab.co
|
|||||
1 2 | TCB Scope |
A1: Low Power Transmitters below 1 GHz (except Spread Spectrum), Unintentional Radiators, EAS (Part 11) & Consumer ISM devices
|
||||
app s | FCC ID | |||||
1 2 | Grantee Code |
A3L
|
||||
1 2 | Equipment Product Code |
SW248
|
||||
app s | Person at the applicant's address to receive grant or for contact | |||||
1 2 | Name |
J**** C********
|
||||
1 2 | Title |
General Manager
|
||||
1 2 | Telephone Number |
973-8********
|
||||
1 2 | Fax Number |
973-8********
|
||||
1 2 |
j******@samsung.com
|
|||||
app s | Technical Contact | |||||
1 2 | Firm Name |
PCTEST Engineering Lab., Inc.
|
||||
1 2 | Name |
R****** O******
|
||||
1 2 | Physical Address |
6660-B Dobbin Road
|
||||
1 2 |
Columbia, Maryland 21045
|
|||||
1 2 |
United States
|
|||||
1 2 | Telephone Number |
410-2********
|
||||
1 2 | Fax Number |
410-2********
|
||||
1 2 |
r******@pctestlab.com
|
|||||
app s | Non Technical Contact | |||||
n/a | ||||||
app s | Confidentiality (long or short term) | |||||
1 2 | Does this application include a request for confidentiality for any portion(s) of the data contained in this application pursuant to 47 CFR § 0.459 of the Commission Rules?: | No | ||||
1 2 | Long-Term Confidentiality Does this application include a request for confidentiality for any portion(s) of the data contained in this application pursuant to 47 CFR § 0.459 of the Commission Rules?: | No | ||||
if no date is supplied, the release date will be set to 45 calendar days past the date of grant. | ||||||
app s | Cognitive Radio & Software Defined Radio, Class, etc | |||||
1 2 | Is this application for software defined/cognitive radio authorization? | No | ||||
1 2 | Equipment Class | JBP - Part 15 Class B Computing Device Peripheral | ||||
1 2 | Description of product as it is marketed: (NOTE: This text will appear below the equipment class on the grant) | CD-RW Drive | ||||
1 2 | Internal CD-R/RW Drive | |||||
1 2 | Related OET KnowledgeDataBase Inquiry: Is there a KDB inquiry associated with this application? | No | ||||
1 2 | Modular Equipment Type | Does not apply | ||||
1 2 | Purpose / Application is for | Class II permissive change or modification of presently authorized equipment | ||||
1 2 | Original Equipment | |||||
1 2 | Composite Equipment: Is the equipment in this application a composite device subject to an additional equipment authorization? | No | ||||
1 2 | Related Equipment: Is the equipment in this application part of a system that operates with, or is marketed with, another device that requires an equipment authorization? | No | ||||
1 2 | Grant Comments | Class II Permissive Change | ||||
1 2 | Is there an equipment authorization waiver associated with this application? | No | ||||
1 2 | If there is an equipment authorization waiver associated with this application, has the associated waiver been approved and all information uploaded? | No | ||||
app s | Test Firm Name and Contact Information | |||||
1 2 | Firm Name |
Samsung Electronics Co., Ltd.
|
||||
1 2 |
SAMSUNG ELECTRONICS CO., LTD.
|
|||||
1 2 | Name |
T******** S********
|
||||
1 2 |
N****** P******
|
|||||
1 2 | Telephone Number |
82-33********
|
||||
1 2 |
82-31********
|
|||||
1 2 | Fax Number |
82-33********
|
||||
1 2 |
82-31********
|
|||||
1 2 |
@******@.
|
|||||
1 2 |
n******@samsung.co..kr
|
|||||
Equipment Specifications | |||||||||||||||||||||||||||||||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
Line | Rule Parts | Grant Notes | Lower Frequency | Upper Frequency | Power Output | Tolerance | Emission Designator | Microprocessor Number | |||||||||||||||||||||||||||||||||
1 | 1 | 15B | |||||||||||||||||||||||||||||||||||||||
Line | Rule Parts | Grant Notes | Lower Frequency | Upper Frequency | Power Output | Tolerance | Emission Designator | Microprocessor Number | |||||||||||||||||||||||||||||||||
2 | 1 | 15B |
some individual PII (Personally Identifiable Information) available on the public forms may be redacted, original source may include additional details
This product uses the FCC Data API but is not endorsed or certified by the FCC