320+520-E 7/21/98 11:33 AM Page i Color Monitor Owners Instructions 320+520-E 7/21/98 11:33 AM Page ii C A U T I O N RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulat-
ed dangerous voltage within the products enclosure that may be of sufficient magnitude to constitute a risk of electric shock. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and servicing instructions in the literature accompanying the appliance. About this Manual This manual shows the precautions, features, specifications, installation, and opea-
ration of your LCD monitor. Unpacking your Monitor Please make sure the following items are included with your computer monitor:
This Manual Warranty Card
(not available in all areas) Monitor and Stand-base Microphone Output Cable Sound Cable Signal Cable Diskette DC Adapter (Optional) Power Cable Note: You can connect the LCD monitor to a Macintosh computer using an optional adapter. For the optional adapter, please contact your LCD monitor dealer. ii 320+520-E 7/21/98 11:33 AM Page 1 Table of Contents Precautions . 2 Overview of LCD Monitor . 3 Frontview........................................................................................3 Rearview ........................................................................................4 Installation . 5 Connecting Your LCD Monitor ....................................................5 Adjusting Your LCD Monitor . 6 Screen Image Adjustment...........................................................6 Automatic Adjustment ..........................................................7 Manual Adjustments.............................................................8 Non-OSD Controls ...............................................................12 Audio Controls......................................................................13 Audio Adjustment................................................................13 Power Saver.................................................................................14 Troubleshooting ..........................................................................15 A p p e n d i x . 1 8 Electrical Specifications............................................................18 Mechanical Specifications.......................................................19 Pin Assignments .........................................................................20 Display Modes Timing Chart.....................................................21 1 320+520-E 7/21/98 11:33 AM Page 2 Precautions Please read and follow these instructions when connecting and using your LCD monitor. Do not touch the surface of the LCD monitor panel with objects having sharp tips or edges. Although the surface of the TFT-LCD monitor has been coated to have scratch resistance, touching the surface with sharp objects can damage the panel. Do not press hard or allow heavy objects to fall onto the sur face of the LCD monitor. Keep the LCD monitor away fr om direct sunlight and other heat sources. Setting up the LCD monitor under direct sunlight can significantly decrease the contrast and increase glare. Also, if the ambient temperature is out of the guaranteed operation specifi-
cation, the panel can show residual images that will overlap other images. This ghost-like residual image will gradually disappear as time passes, but for some extreme cases this residual image means that the LCD panel has been permanently dam-
aged. When you set up the LCD monitor, allow enough r oom for ventilation ar ound the back of the LCD monitor cabinet. The LCD monitor has guaranteed operation temperature specifications. Reserving ample space for ventilation and not blocking the ventilation holes on the back of the monitor is essential for the safe and stable operation of the LCD monitor. Use the enclosed power cord and optional adapter. The enclosed power cord and optional adapter are specifically designed for the LCD monitor you just purchased. Connecting a different power cord and adapter can cause a fire or equipment damage. Keep liquids away fr om the LCD monitor. Although the LCD panel is especially coated to protect it from scratches, dust and moisture, it is not waterproof. Spillage onto the LCD panel or cabinet can result in electric shock and/or permanent equipment damage. When you spill liquid on the cabinet, unplug the LCD monitor immediately and have it checked by a qualified technician. Do not use any strong solvents or abrasive cleansers to clean the LCD panel. The use of any strong solvents or abrasive cleansers can damage the very thin coating layer. This coating improves the screen quality of the LCD monitor. Use a soft cloth to protect the surface of the LCD monitor when removing dust or any stains. 2 320+520-E 7/21/98 11:34 AM Page 3 Overview of LCD Monitor Frontview 2 3 10 5 Screen Controls 4 1 10 6 9 8 7 1. Menu [
] button. Use this button to activate the on-screen display or to enter a selection in the on-screen display. 2. Exit button. Use this button to exit the on-screen display. 3. Up [ s
] and /+ buttons.
] / Down [ t Use these buttons to choose or adjust items in the on-screen display. 4. Power button and Indicator. Use this button to turn the monitor On and Off. The indicator light in the middle of the button glows green during normal operation and glows amber while the monitor is in the power saving mode or if the signal cable is disconnected. Audio Controls 5. Audio On/Off and Volume. Use this button to turn the sound On and Off and to control the sound volume. 6. Bass. Use this button to adjust the volume of the low sounds. 7. Treble. Use this button to adjust the volume of the high sounds. 8. Microphone On/Off. Use this button to turn the internal microphone On or Off. 9. Microphone. Picks up sound and sends it to the sound card in your PC. 10. Amplified Ster eo Speakes 3 320+520-E 7/21/98 11:34 AM Page 4 Overview of LCD Monitor Rearview 2 6 5 1 3 4 1. Signal cable. Connect your signal cable to the port of video card in the PC. 2. Power port. Connect the power cable here. 3. Microphone out port. Connect a cable here to send sound from the monitors microphone to the com-
puters sound card. 4. Audio in por t. Connect a cable here to bring in sound from your computers sound card. 5. External microphone jack. Connect an external microphone here. Using an external microphone automati-
cally disconnects the monitors internal microphone. 6. Headphone jack. Connect headphones here. When you connect headphones, the monitors speak-
ers are turned off. 4 320+520-E 7/21/98 11:34 AM Page 5 Installation Before connecting the LCD monitor to your computer, make sure that your computer supports the video mode supported by the LCD monitor. If the video mode, at the time of installation, is not one supported by the LCD monitor, the LCD monitor may not dis-
play the image as it is intended. Connecting Your LCD Monitor 1. Be sure that the power switches of both the Computer and the LCD monitor are OFF. 2. If you are using a Macintosh computer, connect the other end of the signal cable to a Macintosh adapter. (The adapter is not included with your monitor. Contact your dealer for more information.) If you are using a standard PC and graphics board, skip to step 5. 3. Follow the instructions included with your Macintosh-to-PC adapter to set the configurations on your adapter, if necessory. 4. Connect the signal cable to the video port on the back of your computer. This port might be directly attached to your computer, or it might be part of a video board, video card, or graphics card. 5. Connect the power cable for the LCD monitor to the back of your monitor. 6. Follow the directions that came with your sound card or your computer to connect the monitors speakers and microphone. 7. Plug the computer and monitor power cables into a nearby outlet. 8. Turn your computer and monitor on. If your monitor displays an image, you have successfully installed the monitor. If the monitor does not display an image, check all the connections and follow the troubleshooting guide beginning on page 15. 9. Your LCD monitor is now ready to use, but to get the best image on the LCD moni tor, most of the LCD monitor parameters must be fine tuned to work with the video adapter you are using. The following sections will guide you through the step-by-
step procedures for adjusting the parameters for your specific needs. Your LCD monitor uses an On-Screen Display (OSD) which gives you a convenient way to fine tune the quality of the screen image. Six control buttons on the front panel of the LCD monitor are used to operate the OSD menu. 5 320+520-E 7/21/98 11:34 AM Page 6 Adjusting Your LCD Monitor 1. The MENU button turns on the menu and activates the highlighted function. 2. Push the EXIT button to stop and close the OSD. 3. Use the s buttons to move between the function menus, and use the and + but-
and t tons to make adjustments to the selected function option. Your LCD monitor also provides audio controls located on the front of the stand. The audio controls are described starting on page 13. Screen Image Adjustment Tip 1:
The LCD monitor needs time to become thermally stable the first time you turn it on each day. Thus, to achieve more accurate adjustments for parameters, allow the LCD monitor to warm up (be On) for at least 20 minutes before making any screen adjustments. Tip 2:
The image on the LCD monitor is viewed best when the monitor is placed just below eye level. Please tilt the monitor screen for your viewing comfort. Tip 3:
The accompanying installation diskette with the label Screen Manager contains utilities that are useful when making screen adjustments. Install and run the Screen Manager and read the readme.txt file before you make adjustments. Caution: Do not push and hold in for more than 3 seconds any control button on the front panel of the monitor. Doing so may activate a special function that replaces the parameters with the factory preset values. 6 320+520-E 7/21/98 11:34 AM Page 7 Adjusting Your LCD Monitor Automatic Adjustment Your LCD monitor is designed to interface with the standard analog Red, Green and Blue video signals from a PC or graphics video board. The video signal from a PC is converted to a digital signal through an Analog-to-Digital Converter (ADC). To make the proper conversion for accu-
rate image performance, the LCD monitor must generate exactly the same pixel clock rate and must synchronize it with the clock signal coming from the PC. When the clocks are not cor-
rectly matched, some vertical and horizontal distortion may appear on the screen. Using the Automatic Adjustment function, you can get a more stable image. Your LCD monitor can automatically set most adjustment parameters: Video Gain, Frequency, Fine, and Position using the OSD Auto Adjustment function. Even though you can set most image adjustments automatically, distortion or noise may remain depending on the video board performance. Thus, after using the Auto Adjustment function, we recommend that you readjust the function settings to get the very best picture possible. Caution: Use only the Samsung provided software and the OSD to make parameter adjust ments. Software available from other vendors will not work properly with this LCD monitor and may damage the monitor. Procedure 1. Turn on your PC in accordance with its instructions and push the Power button on the front 2. of your LCD monitor. Install the Screen Manager utility program into your PC system in accordance with the readme.txt file. 3. Run the Screen Manager utility program by clicking the icon, and follow the instructions. button to move down and to highlight the icon and see the Auto/Reset 4. Use the t 5. menu, then push the MENU button again. If Auto Adjustment is not highlighted, use the s button again. button to highlight it and push the MENU Quick Step : Push the + button twice to star t the Auto Adjustment Function. 6. Push the + button to activate the Auto Adjustment function. 7. If you notice horizontal or ver tical lines flickering on your scr een, use the Coarse and Fine functions found on the Image Lock menu to r educe or eliminate these lines. If the display area is not centered on the screen, use the Position menu to move the display area horizontally and/or vertically on the screen. 8. 9. Use the Brightness and Contrast menus to adjust the screen for your eye comfort. 10. Make any other desired adjustments using the OSD menus and the directions found in the following sections. 11. We suggest that you lock the OSD menu system when you have your LCD monitor properly 12. Exit the OSD menu system by pushing the EXIT button 1 or 2 times until the OSD menu disap-
adjusted. pears. Caution: After the OSD disappears, do not continue holding in the EXIT button. If you do, the OSD may reset to the original factory settings and you will need to make your adjust ments again. 7 320+520-E 7/21/98 11:34 AM Page 8 Adjusting Your LCD Monitor Manual Adjustments When making adjustments to the way your LCD monitor displays an image, we recommend that you use the test pattern provided by the SyncMaster Screen Manager. If your computer operating system cannot run this utility program, display a checkerboard pattern on the screen. For Macintosh users, you can display a checkerboard pattern using the General Controls from the Macintosh Control Panel menu. The information provided below describes the OSD menu options in the order that they appear on the OSD. When you first install your monitor, we recommend that you first use the Automatic Adjustment procedure as outlined above before making other adjustments. The numbers shown along the right side of the Brightness, Contrast, Image Lock, Position, Color Control and Menu Position OSD windows represent arbitrary values for reference only. OSD Icon
& Menu Function Name Brightness Contrast Effect of Button
+
Image Lock These functions correct for noise (slight i n t e rf e rence) in the video signal from the computer or video board. Fine Fine eliminates or limits noise which causes horizontal lines or areas on the scre e n where the image appears to be unstable and jitters, shimmers or flickers. Use the and +
buttons to adjust away the interf e rence. If you cannot get satisfactory results using the Fine adjustment, get the best results you can with the Coarse adjustment then use Fine again. 8 320+520-E 7/21/98 11:34 AM Page 9 Adjusting Your LCD Monitor OSD Icon
& Menu Function Name Coarse Effect of Button
+
Coarse eliminates or limits noise which causes vertical lines or areas on the screen where the image appears to be unstable and jitters, shimmers or flickers. This function slightly changes the width of the display image. Use the H-Position function on the Position menu to center the display image on the screen. Position H-Position V-Position Color Temperature Mode 1 Mode 2 Mode 3 Color temperature changes the color coordi-
nates to make the colors appear more warm
(red) or cool (blue) or to use the LCD natural characteristics. Select the mode you find most comfortable using then fine tune the colors using the Color Control menu. Colors appear with the LCD panels natural characteristics. Colors appear more cool with a bluish cast Colors appear more warm with a reddish cast Color Control After selecting a Color Te m p e r a t u re mode, you can adjust the hue that the screen dis-
plays for red, green and blue. Red Green Blue Decrease redness Increase redness Decrease greenness Increase greenness Decrease blueness Increase blueness 9 320+520-E 7/21/98 11:34 AM Page 10 Adjusting Your LCD Monitor OSD Icon
& Menu Function Name Auto / Reset Effect of Button
+
See page 7 for a complete description of the Automatic Adjustment function. Use the two Reset functions to re s t o re the scre e n settings to their original manufacturing set-
t i n g s . Auto Adjustment Geometry Reset Color Reset No No Yes Yes Resets the Position and Zoom functions. No Yes Resets the Brightness, Contrast and Color Control functions. Image Size Move highlight left Move highlight right Zoom Scales the contents of the entire display are a to 1, 2, 4, and 8 times the normal size. Display Size Normal Expand If your computer or video board supplies a signal rate and resolution lower than 1024x768, this LCD monitor provides a scal-
ing processor which can expand the rate up to 1024x768. If the signal rate is already XGA
(1024x768) you will see (Disable) below Expand. This means that this function is not available because the screen is already at its largest size. Normal
(VGA:640X480) Expanded
(1024X768) Normal
(SVGA:800X600) 10 320+520-E 7/21/98 11:34 AM Page 11 OSD Icon
& Menu Adjusting Your LCD Monitor Effect of Button
+
This menu offers functions that you may find useful, but will probably use only when initially setting up your LCD monitor. and t Use the s buttons to select one of the five languages to use for the OSD. The language you choose affects only the lan-
guage that the OSD displays. It has no effect on any software running on your computer. This function allows you to set the location where the OSD menu displays on your screen. The default location is in the center of the screen. Function Name M i s c e l l a n e o u s Language English Deutsch Espaol Franais Italiano Menu Position H-Position V-Position Menu Display Time This function defines how long the OSD will stay active, after you stop pushing any but-
tons. Use the and + buttons to select between 5, 10, 20, and 200 seconds. 11 320+520-E 7/21/98 11:34 AM Page 12 Adjusting Your LCD Monitor OSD Icon
& Menu Function Name Display Mode Effect of Button
+
This is an information only screen which shows the frequency and resolution that your LCD monitor is receiving from your computer or video board. Non-OSD Controls OSD Locking You can lock the OSD controls to protect your settings from accidental or unwanted changes by pushing and holding in the MENU button for 5 seconds. The OSD will open then close automatically. When you open the OSD again, Locked will appear along the bottom of most menus and you cannot change any controls except Brightness and Contrast.To unlock the OSD, push and hold in the MENU button for 5 seconds again. 12 320+520-E 7/21/98 11:34 AM Page 13 Adjusting Your LCD Monitor Audio Controls Your LCD monitor provides four audio control buttons located on the front of the stand. Audio Adjustments To access the On/Off, Volume, Bass and Treble functions, push the appropriate blue control button until it pops out, then turn it to the right or left to adjust the function. Function Name Audio On/Off and Volume Bass Treble Effect of Control Movement Left Off Decrease volume Decrease low sounds Decrease high sounds Right On Increase volume Increase low sounds Increase high sounds Your LCD monitor includes an internal microphone which you can turn On or Off using the rightmost control of the Audio controls. Function Name Microphone On/Off Effect of Control Movement In On Out Off 13 320+520-E 7/21/98 11:34 AM Page 14 Adjusting Your LCD Monitor Power Saver This monitor has a built-in power management system called PowerSaver. This system saves energy by switching your monitor into an off mode when it has not been used for a certain amount of time. This system operates with a VESA DPMS compliant video card installed in your computer. You use a software utility installed on your computer to set up this feature. See the table below for details. State Normal operation Horizontal Sync Vertical Sync Video Active Active Active Power Indicator Green Power Consumption 320TFT : 40W(max.) 30W(nominal) 520TFT : 45W(max.) 35W(nominal) Power-Saving Function Mode EPA/NUTEK Standby mode Inactive Active Blanked Amber Suspend mode/ Power-off mode/
Position A1 Position A2 Active Inactive Blanked Inactive Inactive Blanked Amber Blinking Amber Blinking
(0.5 Sec,Interval) (1.0 Sec,Interval) Less than 5 W Less than 5 W Less than 5 W NOTE: This monitor automatically returns to normal operation when horizontal and vertical sync return. This occurs when you move the computer's mouse or press a key on the keyboard. This monitor is EPA Energy Star compliant and NUTEK compliant when used with a computer equipped with VESA DPMS functionality. If your computer system cannot support a display power management function, you can purchase an optional DPMS software program to enable the power saving function. Please contact Samsung or your dealer for more informa-
tion. For energy conservation, turn your monitor OFF when it is not needed, or when leaving it unattended for long periods. 14 320+520-E 7/21/98 11:34 AM Page 15 Adjusting Your LCD Monitor Troubleshooting If you have a problem setting up or using your LCD monitor, you may be able to solve it your-
self. Before contacting customer service, try the suggested actions that are appropriate to your problem. Image Problems Problem Suggested Action Screen is blank and power indicator is off. Ensure that the power cord is firmly connected and the LCD monitor is On. Reference Installation, page 5 Check Signal Cable appears on screen. Installation, page 5 Ensure that the signal cable is firmly connected to the PC or video board. Ensure that the PC is turned On. The image is too light or too dark Adjust the Brightness and Contrast. Brightness, page 8 Contrast, page 8 Horizontal bars appear to flicker, jitter or shimmer on the image. Adjust the Fine function. Image Lock, Fine, page 8 Vertical bars appear to flicker, jitter or shimmer on the image. Adjust the Coarse function and then adjust the Fine function. Image Lock, Coarse, page 9 Image Lock, Fine, page 8 Image is not stable and may appear to vibrate. Check that the display res-
olution and frequency from your PC or video board is an available mode for your LCD monitor. If the setting is not correct, use your computer utility program to change the dis-
play settings. Misc., Display Mode, page 12 Display Modes Timing Chart, page 21 On your computer: Display Settings. For Windows 95 or later, use Start, Settings, Control Panel, Display, and Settings. Note: Your LCD monitor supports the multiscan display func tion within the following frequency domain:
Horizontal frequency:
Vertical frequency:
Maximum refresh rate:
30 kHz - 61 kHz 50 Hz - 75 Hz 1024 x 768 @ 75 Hz 15 320+520-E 7/21/98 11:34 AM Page 16 Adjusting Your LCD Monitor Problem Suggested Action Reference Image is too small using the VGA and SVGA resolution. Use the Expand function to stretch the image to 1024x768. Image Size, Expand, page 10 Image is too big and extends beyond the edge of the screen. Disable or adjust the Image Size, Zoom, page 10 Zoom-in function as appro-
priate. Image is not centered on the screen. Adjust the image horizontal and vertical position. Position, H-Position, page 9 Position, V-Position, page 9 Suggested Action Ensure that the audio cable is firmly connected to both the audio-in port on your LCD monitor and to the audio-out port on your sound card or computer. Rotate the Audio On/Off and Volume control to the right to turn it on and raise the volume. Rotate the Audio On/Off and Volume control to the right to raise the volume. If the volume is still too low after turning the control to its maximum, check the volume control on the com-
puter sound card or soft-
ware program. Reference Installation, page 5 Audio Controls, page 13 Audio Controls, page 13 Refer to your computer, sound card or software docu-
mentation. Audio Problems Problem No sound. Sound level is too low. 16 320+520-E 7/21/98 11:34 AM Page 17 Adjusting Your LCD Monitor Problem Suggested Action Reference Howling effect occurs. Decrease the volume Audio Controls, page 13 slightly. If you are using an external microphone, move it away from the speakers and adjust the volume level. Sound is too high pitched or too low pitched. Adjust the Treble and Bass as appropriate. Audio Controls, page 13 Microphone is not working. Installation, page 5 Your computer or sound card documentation. Check the microphone cable connection. Your sound card must be compatible with an inter-
nal, embedded micro-
phone. If it is not, use the microphone that came with your computer or sound card. 17 320+520-E 7/21/98 11:34 AM Page 18 Appendix Electrical Specifications LCD Panel Size:
Display area:
Type:
Pixel pitch:
Viewing angle:
SyncMaster 320TFT 13.3 diagonal 270.3 (H) x 207.8 (V) Amorphous silicon TFT LCD (Liquid Crystal Display) 0.264 (H) x 0.264 (V) 55/55/60/60 (U/D/L/R) (degrees) SyncMaster 520TFT 15.0 diagonal 304.1 (H) x 228.1 (V) 0.297 (H) x 0.297 (V) Synchronization (Scan Frequency) Horizontal:
Vertical:
30 -61kHz (Automatic scanning) 50-75Hz(Automatic scanning)
(1024x768 is upto 75Hz) 16.7 Million colors Display Colors:
Display Resolution Optimum mode:
Native mode:
Expand mode:
1024 dots x 768 lines 640 x 480, 800 x 600, 832 x 624 (Macintosh), 1024 x 768 640 x 480 -> 1024 x 768 800 x 600 -> 1024 x 768 832 x 624 -> 1024 x 768 (Macintosh) 1024 x768-> 1024 x 768 Maximum Input Pixel Clock:
80MHz at 1024x768@75Hz Input Signal Sync:
Video signal:
Signal Cable:
H/V Separate, TTL, Positive or Negative H/V Composite, TTL, Positive or Negative Sync-On-Green 0.3 Vp-p, Negative 0.714Vp-p@75 ohm, Positive 26 pin MDR connector (monitor) to 15 pin d-sub (PC) AC 100-240 Volt 10%, 60Hz/50Hz 3Hz Power Supply:
Power Consumption Normal:
Maximum:
Power Saving:
30 Watt (without audio) 40 Watt (with audio) 5 Watt
(VESA DPMS compliance) 35 Watt (without audio) 45 Watt (with audio) 5 Watt
(VESA DPMS compliance) 18 320+520-E 7/21/98 11:34 AM Page 19 Appendix Mechanical Specifications SyncMaster 320TFT SyncMaster 520TFT Unit (WxHxD):
Carton (WxHxD):
355.0 x 395.0 x 196.0 mm 455.0 x 488.0 x 282.0 mm 404.0 x 419.0 x 196.0mm 475.0 x 510.0 x 282.0 mm Dimension Weight Unit:
Carton:
6.4Kg 8.0Kg 7.5Kg 9.5Kg Environmental Considerations Operating Temperature:
Operating Humidity:
50 F to 104 F (10 C to 40 C) 10% to 80%
Storage Temperature:
Storage Humidity:
-13 F to 113 F (-25 C to 45 C) 5% to 95%
Audio Characteristics Built-in Microphone:
Audio Input:
Sound Output:
Frequency Response:
High Sensitivity Condenser Microphone (mono) Left/Right Stereo Phone Jack, 0.5Vrms 1.0W (left) + 1.0W (right)/THD 1% at 4ohm 80Hz - 20KHz (at -3dB) Headphone: Max 50mW output (3.5-pi jack) 19 320+520-E 7/21/98 11:34 AM Page 20 Appendix Pin Assignments 1. 15pin-26pin D-sub connector (slim-type), 15-pin side Pin 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 Separate H/V Composite H/V Sync-on-green Red Green Blue GND GND (DDC Return) GND-Red GND-Green GND-Blue No Connection GND-Sync/Self Test GND DDC Data Horizontal Sync Vertical Sync DDC Clock Red Green Blue GND GND (DDC Return) GND-Red GND-Green GND-Blue No Connection GND-Sync/Self Test GND DDC Data H/V Sync Not used DDC Clock Red Green + H/V Sync Blue GND GND (DDC Return) GND-Red GND-Green GND-Blue Not used GND-Sync/Self Test GND DDC Data Not used Not used DDC Clock 2. 15pin-26pin D-sub connector (slim-type), 26-pin side Separate H/V Composite H/V Sync-on-green Red Green Blue GND GND (DDC Return) GND-Red GND-Green GND-Blue No Connection GND-Sync/Self Test GND DDC Data Horizontal Sync Vertical Sync DDC Clock Red Green Blue GND GND (DDC Return) GND-Red GND-Green GND-Blue No Connection GND-Sync/Self Test GND DDC Data H/V Sync Not used DDC Clock Red Green + H/V Sync Blue GND GND (DDC Return) GND-Red GND-Green GND-Blue Not used GND-Sync/Self Test GND DDC Data Not used Not used DDC Clock GND GND GND Pin 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16~
26 20 320+520-E 7/21/98 11:34 AM Page 21 Appendix Display Modes Timing Chart (Factory preset Modes) No. Display mode Horizontal Frequency Vertical Frequency Pixel Clock Sync Polarity
(horiz./vert.) 1 2 3 4 5 6 7 8 9 10 11 12 VGA, 640x350 VGA, 720x400 VGA, 640x480 VGA, 640x480 Mac, 640x480 SVGA, 800x600 SVGA, 800x600 SVGA, 800x600 Mac, 832x624 XGA, 1024x768 XGA, 1024x768 XGA, 1024x768 70.00Hz 31.47kHz 70.00Hz 31.47kHz 60.00Hz 31.47kHz 37.50kHz 75.00Hz 35.00kHz 66.667Hz 56.20Hz 35.16kHz 60.30Hz 37.88kHz 75.00Hz 46.87kHz 75.00Hz 49.73kHz 48.36kHz 60.00Hz 70.00Hz 56.48kHz 60.02kHz 75.00Hz 25.175MHz 28.322MHz 25.175MHz 31.500MHz 30.240MHz 36.000MHz 40.000MHz 49.500MHz 57.250MHz 65.000MHz 75.000MHz 78.750MHz
+/-
-/+
+,-/+,-
+,-/+,-
-/-
+,-/+,-
+,-/+,-
+,-/+,-
+,-/+,-
+,-/+,-
+,-/+,-
+,-/+,-
21 320+520-E 7/21/98 11:34 AM Page 22 85 West Tasman Drive San Jose, CA 95134 USA Tel) 408-544-5124 Fax) 408-544-5191 Provided with this monitor is a detachable power supply cord with IEC320 style terminations. It may be suitable for connection to any UL Listed personal computer with simi-
lar configuration. Before making the connection, make sure the voltage rating of the computer convenience out-
let is the same as the monitor and that the ampere rating of the computer convenience outlet is equal to or exceeds the monitor voltage rating. For 120 Volt applications, use only UL Listed detachable power cord with NEMA configuration 5-15P type (parallel blades) plug cap. For 240 Volt applications use only UL Listed Detachable power supply cord with NEMA config-
uration 6015P type (tandem blades) plug cap. IC Compliance Notice This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations of ICES-003. Cet appareil numrique de classe B respecte toutes les exigences du Rglement ICES-003 sur les quipements produisant des interfrences au Canada. MPR II Compliance This monitor complies with SWEDAC (MPR II) re c o m m e n d a-
tions for reduced electric and magnetic fields. European Notice Products with the CE Marking comply with both the EMC Directive (89/336/EEC), (92/31/EEC), (93/68/EEC) and the Low Voltage Directive (73/23/EEC) issued by the Commission of the European Community. Compliance with these directives implies conformity to the following European Norms:
EN55022 (CISPR 22) Radio Frequency Interference EN50082-1 : 1992 Electromagnetic Immunity EN60555-2 (IEC555-2) Power Line Harmonics EN60555-3 (IEC555-3) Voltage Fluctuations EN60950 (IEC950) Product Safety. FCC Information User Instructions The Federal Communications Commission Radio Frequency Interference Statement includes the following warning:
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide re a s o n-
able protection against harmful interf e rence in a re s i d e n t i a l installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accor-
dance with the instructions, may cause harmful interf e re n c e to radio communications. However, there is no guarantee that i n t e rf e rence will not occur in a particular installation. If this equipment does cause harmful interf e rence to radio or television receptions, which can be determined by turning the equipment off and on, the user is encouraged to try to corre c t the interf e rence by one or more of the following measure s :
Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit dif-
ferent from that to which the receiver is connected. Consult the dealer or an experienced radio/TV techni-
cian for help. User Information Changes or modifications not expressly approved by the p a rty responsible for compliance could void the users authority to operate the equipment. If necessary, consult your dealer or an experienced radio/television technician for additional suggestions. Yo u may find the booklet called How to Identify and Resolve Radio/TV Interf e rence Pro b l e m s helpful. This booklet was p re p a red by the Federal Communications Commission. It is available from the U.S. Government Printing Off i c e , Washington, DC 20402, Stock Number 004-000-00345-4. Warning User must use shielded signal interface cables to main-
tain FCC compliance for the product. Declaration of conformity for prod-
ucts Marked with FCC Logo This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interf e rence, and (2) this device must accept any interf e rence received, includ-
ing interference that may cause undesired operation. The party responsible for product compliance:
SAMSUNG ELECTRONICS CO., LTD QA Lab of Samsung America 320+520-E 7/21/98 11:34 AM Page 23 U.S.A. :
Samsung Electronics America (SEA) One Samsung Place Ledgewood, NJ 07852 Tel. : 1-800-SAMSUNG (1-800-726-7864) Fax-on-Demand for product information :
1-800-229-2239 CANADA :
Samsung Electronics Canada Inc. 7037 Financial Drive Mississauga, Ontario L5N 6R3 Tel. : 1-800-SAMSUNG (1-800-726-7864) Fax. : (905) 542-1199 GERMANY :
Samsung Electronics GmbH Samsung-Haus Am Kronberger Hang 6/65824 Schwalbach/Ts. Tel. : 06196-66-1134 Fax. : 06196-66-1133 AUSTRALIA :
Samsung Electronics Australia Pty Ltd. Unit G, 10-16 South Street, Rydalmere, N.S.W. 2116 P.O. BOX 368 Tel. : (02) 638 5200 ITALIA :
Samsung Electronics Italia SpA Via C. Donat Cattin, 5-20063 Cernusco sul Naviglio (Mi) Tel. : 167-010740 PANAMA :
Servicios Samsung (Zona Libre), S.A. 50 and 61 Streets Sta, Cecilia Bdl. Don Camilo, Panama City Tel. : (507) 264-0195 or 269-5571 Fax : (507) 269-5568 ESPAA :
Samsung Electrnics Comercial Ibrica, S.A. Ciencies, 55-65 (Polgono Pedrosa) 08908 Hospitalet de Llobregat (Barcelona) Tel. : (93) 261 67 00 Fax. : (93) 261 67 50 UK :
Samsung Electronics (UK) Ltd. Samsung House, 225 Hook Rise South Surbiton, Surrey KT6 7LD Tel. : (0181) 391 0168 Fax. : (0181) 397 9949
<European Service Center & National Service>
Stafford Park 12 Telford, Shropshire, TF3 3BJ Tel. : (01952) 292 262 Fax. : (01952) 292 033 THAILAND :
Samsung Service Center 729-729/1 JSP Tower Rachadapisek RD., Bangpongpang, Yannawa, Bangkok 10120 Tel : (662) 2954508-14 Fax : (662) 2954267 SOUTH AFRICA :
Samsung Electronics South Africa Somerset Office Park 5 Libertas Road Bryanston, South Africa Tel : (27)-11-463-5678 Fax : (27)-11-463-5215 BRASIL :
Samsung Eletrnica da Amazonia Ltda. R. Prof. Manoelito de Ornellas, 303-2 Andar Chcara Sto. Antnio cep : 04719-040 So Paulo SP Tel. : (011) 541-8500 Fax : (011) 523-3995, 522-0726 CODE NO. : BN68-60002A ( Rev. 0.3 ) Printed on recyclable paper