HBH34 Quick Start Guide - Front Size: 432 x 140 mm Printing Color: Black Matl: 100 gsm WF paper Nov 11, 2016 FCC ID: EMOHBH34 IC: 986B-HBH34 Set Up HBH34 Staff Quick Start Guide Included HBH34 system Security tether 1 2 4 Set the Volume Limiter Switch on the back of the unit (Off for large rooms, On for smaller rooms). off on volume limit Security tether Setting the Time Zone and Clock
(Factory Preset Clock) Remove thumbscrew and remove back cover to access staff controls. Secure the attached Security Tether to a wall or other permanent surface. CAUTION: DO NOT attach to an AC outlet or cause it to become entangled with anything that can create a hazardous situation. outlet 3 Connect AC plug to a working outlet that is not controlled by an On/Off switch. The first time you connect your new preset clock to the AC outlet, the unit will automatically show the correct Eastern Standard time, which is the default setting. If you are not in the Eastern time zone, you must change the default setting to match your time zone (see Time Zone Setting below). Once the correct time zone is set, if the time displayed is not correct, follow steps under Manual Clock Setting to set the correct time, year and date. Time Zone Setting Make sure unit is in Power OFF mode. Press and hold the Time Zone Button on the back of the unit for 2 seconds. The time zone will flash. time zone 2 SECS Press the or + Button to cycle to local time zone. Press Time Zone Button again to confirm. Daylight Saving Time The unit ships with the Daylight Saving Time (DST) switch in Auto position, and will automatically adjust when the time changes in March and November. If Daylight Saving Time is NOT observed in your loca-
tion, move the DST switch from AUTO to -1 or +1 BEFORE setting time. dst
+1 -1 auto Bluetooth Pairing 1. Press and hold the Bluetooth Button. Unit will enter pairing mode. 2. Select HBH34 on your devices Bluetooth menu. HBH34 Quick Start Guide - Inside Size: 432 x 140 mm Printing Color: Black Matl: 100 gsm WF paper Manual Clock Setting Press and hold the Time Set Button for 2 seconds to enter clock setting mode. time set 2 SECS Press the - or + button to set the time. Press the Time Set Button to confirm the time. The year will flash. time set Press the Time Set Button to confirm the year. The date will flash. time set Press the - or + button to set the date. Hold for rapid adjustment. Press the Time Set Button to confirm the date and exit clock setting. time set Backup Batteries Keep unit connected to AC power when replacing batteries or you will lose settings. Reset Button The courtesy plug on top of the unit is rated for 15 amps. If a guest connects a device that overloads the outlet, the built in circuit breaker will prevent damage to the unit. The Reset Button on the back of the unit will pop out to indicate the outlet was overloaded. Press and release the Reset Button to reset the circuit breaker and restore the courtesy plug to operation. reset Remove pull tab from Backup Battery Compartment located on bottom of theunit. When Low Battery Icon appears on display, replace backup batteries with 2 fresh AA batteries. Make sure polarity (+/) markings match illustration. Maintenance Place the unit on a level surface away from sources of direct sunlight or excessive heat. Press the - or + button to set the year. Once staff has completed setup, replace security cover on back of unit and tighten thumbscrew. Protect your furniture when placing your unit on a natural wood and lacquered finish. A cloth or other protective material should be placed between it and the furniture. Clean your unit with a soft cloth moistened only with mild soap and water. Stronger cleaning agents, such as thinner or similar materials can damage the surface of the unit. HBH34QSG-103116-A 2016 HTI Industries, LLC. All rights reserved Printed in China Generic Legal Sheet for all Hotel model items - Front Size: 108 x 140 mm Color: 1C + 1C (Black) Material: 100 gsm WF paper Aug. 04, 2015 Generic Legal Sheet for all Hotel model items - Back IMPORTANT SAFETY INSTRUCTIONS When used in the directed manner, this unit has been designed and manufactured to ensure your personal safety. However, improper use can result in potential electrical shock or fire hazards. Please read all safety and operating instructions carefully before installation and use, and keep these instructions handy for future reference. Take special note of all warnings listed in these instructions and on the unit. 1. Water and Moisture The unit should not be used near water. For example: near a bathtub, washbowl, kitchen sink, laundry tub, swimming pool or in a wet basement. 2. Ventilation The unit should be situated so that its location or position does not interfere with its proper ventilation. For example, it should not be situated on a bed, sofa, rug or similar surface that may block ventilation openings. Also, it should not be placed in a built-in installation, such as a bookcase or cabinet, which may impede the flow of air through the ventilation openings. 3. Heat The unit should be situated away from heat sources such as radiators, heat registers, stoves or other appliances
(including amplifiers) that produce heat. or as marked on the appliance. 4. Power Sources The unit should be connected to a power supply only of the type described in the operating instructions 5. Power-Cable Protection Power supply cables should be routed so that they are not likely to be walked on or pinched by items placed upon or against them. It is always best to have a clear area from where the cable exits the unit to where it is plugged into an AC socket. 6. Cleaning The unit should be cleaned only as recommended. See the Maintenance section of this manual for 7. Objects and Liquid Entry Care should be taken so that objects do not fall and liquids are not spilled into any cleaning instructions. openings or vents located on the product. 8. Attachments Do not use attachments not recommended by the product manufacturer. 9. Lightning and Power Surge Protection Unplug the unit from the wall socket and disconnect the antenna or cable system during a lightning storm or when it is left unattended and unused for long periods of time. This will prevent damage to the product due to lightning and power-line surges. 10. Overloading Do not overload wall sockets, extension cords, or integral convenience receptacles as this can result in a risk of fire or electric shock. 11. Damage Requiring Service The unit should be serviced by qualified service personnel when:
A. the power supply cable or plug has been damaged. B. objects have fallen into or liquid has been spilled into the enclosure. C. the unit has been exposed to rain. D. the unit has been dropped or the enclosure damaged. E. the unit exhibits a marked change in performance or does not operate normally. 12. Periods of Nonuse If the unit is to be left unused for an extended period of time, such as a month or longer, the power cable should be unplugged from the unit to prevent damage or corrosion. 13. Servicing The user should not attempt to service the unit beyond those methods described in the users operating instructions. Service methods not covered in the operating instructions should be referred to qualified service personnel. FCC Information This device complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. equipment. This device complies with Part 15 of the FCC Rules, operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the users authority to operate the NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. CAN ICES-3 (B)/NMB-3(B) Increase the separation between the equipment and receiver. Questions? visit www.hoteltech.com or call 1-888-744-6835 Toll Free LIMITED 30 DAY WARRANTY
(valid in contiguous U.S.A. only: not valid in Hawaii or Alaska) Hotel Technologies, a division of HTI Industries LLC, (hereafter referred to as Hotel Technologies), warrants this product to be free from defects in workmanship and materials, under normal use and conditions, for a period of 30 days from the date of receipt of the item. Should service be required by reason of any defect or malfunction during the warranty period, Hotel Technologies will repair or, at its discretion, replace this product without charge. This decision is subject to verification of the defect or malfunction upon delivery of this product to the Factory Service Center listed below. Before returning this product for service, please first replace the batteries (if applicable) with fresh ones, as exhausted or defective batteries are the most common cause of problems encountered. If service is still required:
1. Fax a representative at 915.633.1388 with a Return Authorization request including proof of purchase date
(i.e., invoice number and date from distributor or HTI) to receive a Return Authorization Number. Issuance of Return Authorization Number is subject to review prior to granting. NO ITEM CAN BE ACCEPTED WITHOUT A RETURN AUTHORIZATION NUMBER. 2. Remove batteries (if applicable) and pack the unit in a well-padded, heavy corrugated box. 3. Send the unit by method agreed to with your representative to the Factory Service Center listed below:
Consumer Repair Department Hotel Technologies Inc. 1330 Goodyear Drive El Paso TX 79936-6420 NOTE: Improperly packed items or Items received without an RA # cannot receive credit. NOTE: This warranty is valid only if the product is used for the purpose for which it was designed. It does not cover (i) products which have been damaged by negligence, misuse or accident, or which have been modified or repaired by unauthorized persons; (ii) cracked or broken cabinets, or units damaged by excessive heat; (iii) damage to tape cassettes (if applicable); (iv) the cost of shipping this product to the Factory Service Center and its return to the owner. This warranty is valid only in the United States of America and does not extend to owners of the product subsequent to the original purchaser. Any applicable implied warranties are also limited to 30 days, and Hotel Technologies will not be liable for consequential damages. (Some states do not allow limitations on implied warranties or exclusion of consequential damages, so these restrictions may not apply to you.) This warranty gives you specific legal rights, and you may also have other rights which vary from state to state. please contact the appropriate distributor for their warranty terms IC Statement for RF Device This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions:
(1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le prsent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorise aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible d'en compromettre le fonctionnement. The device meets the exemption from the routine evaluation limits in section 2.5 of RSS 102 and compliance with RSS-102 RF exposure, users can obtain Canadian information on RF exposure and compliance. Le dispositif rencontre l'exemption des limites courantes d'valuation dans la section 2.5 de RSS 102 et la conformit l'exposition de RSS-102 rf, utilisateurs peut obtenir l'information canadienne sur l'exposition et la conformit de rf. HBN21-150425-A 2015 HTI Industries, LLC. All rights reserved Printed in China