iBTW750 QSG (English) Size: 420 x 160 mm (folded: 140 x 160 mm) Color: 4C + 4C Material: 260gsm Art Card, 2C + 2C Mar 19, 2019 FRONT PMS185C Color Changing Stereo Speaker System with Wireless Charging Model: iBTW750 QUICK SET-UP Connecting to Power BLUETOOTH PAIRING Pairing and Playing Audio QUICK START GUIDE iBTW750 USB Charging Cable USB Wall Adapter Connect the USB plug to the USB wall adapter, then plug the adapter into a working power outlet. Press and hold the Power Button for 2 seconds to power on the unit. CHARGE UNIT BEFORE USE ABOUT 7 HOURS BACK 8 6 5 4 1 2 7 reset 3 1 Power Button Press and hold for 2 seconds to power unit ON or OFF. 2 Battery/Charge indicator Solid red = charging Solid green = fully charged 3 USB Charge Port Connect included USB cable to charge iBTW750 for portable use. 4 Bluetooth Indicator Fast blinking blue = pairing Slow blinking blue = linking Solid blue = paired to device 5 Bluetooth Button Press and hold for 2 seconds to pair a device with the unit. Press to answer incoming call. Press and hold for 2 seconds to end or decline call. 6 Color Change Button Press and release to cycle through color change modes:
slow fade, fast change, favorite color, pulse to music, preset pulse mode and off. ET RES RES ET EST T T EST reset ET RES RES ET EST T T EST Next, plug the micro USB connector to the micro USB port located under the button controls. Now plug the other micro USB connector to the micro USB port located near the top of the unit. Once connected, the unit should match the drawing below:
7 Pinhole Reset Port If unit fails to respond properly, insert a paper clip or similar tool into the Reset Port on the back of the unit. 8 Wireless Charging USB Port Connect included USB cable for wireless charging operation. reset BATTERY LEVEL A voice prompt will automatically announce when the battery level is very low. Press and hold the Color Mode Button to hear current battery level announcement. BACK IMPORTANT SAFETY INSTRUCTIONS When used in the directed manner, this unit has been designed and manufactured to ensure your personal safety. However, improper use can result in potential electrical shock or re hazards. Please read and follow all safety and operating instructions carefully before installation and use, and keep these instructions handy for future reference. Take special note of all warnings listed in these instructions and on the unit. 1. Water and Moisture The unit should not be used near water. For example: near a bathtub, washbowl, kitchen sink, laundry tub, swimming pool or in a wet basement. 2. Ventilation The unit should be situated so that its location or position does not interfere with its proper ventilation. For example, it should not be situated on a bed, sofa, rug or similar surface that may block ventilation openings. Also, it should not be placed in a built-in installation, such as a bookcase or cabinet, which may impede the ow of air through the ventilation openings. 3. Heat The unit should be situated away from heat sources such as radiators, heat registers, stoves or other appliances (including ampliers) that produce heat. 4. Power Sources The unit should be connected to a power supply only of the type described in the operating instructions or as marked on the appliance. Only use the AC adapter that came with the unit. 5. Power-Cable Protection Power supply cables should be routed so that they are not likely to be walked on or pinched by items placed upon or against them. It is always best to have a clear area from where the cable exits the unit to where it is plugged into an AC socket. 6. Cleaning The unit should be cleaned only using a warm damp cloth. Do not use solvents, etc. 7. Objects and Liquid Entry Care should be taken so that objects do not fall and liquids are not spilled into any openings or vents located on the product. 8. Attachments Do not use attachments not recommended by the product manufacturer. 9. Lightning and Power Surge Protection Unplug the unit from the wall socket and disconnect the antenna or cable system during a lightning storm or when it is left unattended and unused for long periods of time. This will prevent damage to the product due to lightning and power-line surges. 10. Overloading Do not overload wall sockets, extension cords, or integral convenience receptacles as this can result in a risk of re or electric shock. 11. Damage Requiring Service The unit should be serviced by qualied service personnel when:
A. the power supply cable or plug has been damaged. B. objects have fallen into or liquid has been spilled into the enclosure. C. the unit has been exposed to rain. D. the unit has been dropped or the enclosure damaged. E. the unit exhibits a marked change in performance or does not operate normally. 12. No naked ame sources, such as lighted candles, should be placed on the apparatus 13. The power adapter, used as the disconnected device, It is always best to have a clear area from where the cable exits the unit to where it is plugged into an AC socket 14. Periods of Nonuse If the unit is to be left unused for an extended period of time, such as a month or longer, the backup battery should be removed from the unit to prevent damage or corrosion. 15. Servicing The user should not attempt to service the unit beyond those methods described in the users operating instructions. Service methods not covered in the operating instructions should be referred to qualied service personnel. FCC Information FCC Radiation Exposure Statement The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction. Model: iBTW750 FCC ID: EMOIBTW750 IC: 986B-IBTW750 This device complies with Part 15 of the FCC Rules, operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Warning: Changes or modications to this unit not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. CAN ICES-3 (B)/NMB-3(B) Canada Statement This device complies with Industry Canadas licence-exempt RSS standard(s). Operation is subject to the following two conditions:
(1) This device may not cause interference; and
(2) This device must accept any interference, including interference that may cause undesired operation of the device. Le prsent appareil est conforme aux CNR dIndustrie Canada applicables aux appareils radio exempts de licence. Lexploitation est autorise aux deux conditions suivantes :
(1) lappareil ne doit pas produire de brouillage;
(2) lutilisateur de lappareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible den compromettre le fonctionnement. The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction. le dispositif a t valu satisfaire l'exigence gnrale de l'exposition aux rf. l'appareil peut tre utilis dans des conditions d'exposition portatif sans restriction. WARNING/DISPOSAL OF UNIT Do NOT attempt to change the battery. Doing so will void the warranty and could cause injury and damage to your device. To dispose of the unit, follow the instructions below:
Never dispose of used batteries/electronics with ordinary solid wastes, since they contain toxic substances. Always dispose of used batteries/electronics in accordance with the prevailing community regulations. Many electronics retailers now recycle batteries and other electronic components at no charge. GENERAL BATTERY PRECAUTIONS Never use or charge a battery if it appears to be leaking, discolored, deformed, or in any way abnormal. Never disassemble the unit or attempt to remove battery as that could cause leakage of alkaline solution or other electrolytic substances. Avoid charging a rechargeable battery when the temperature is not within 5C - 35C (41 - 95 Fahrenheit). Never expose a battery to any liquid. Never expose a battery to excessive heat such as direct sunlight or re. Never use a battery pack in an unventilated vehicle where excessive internal temperatures may be encountered. Always keep batteries out of the reach of infants and small children. Press and hold the Bluetooth Button for 2 seconds to enter pairing mode. iHome iAV5 Select iHome iAV5 on your Bluetooth device. You will hear a Connected announcement once your device is paired. Use your Bluetooth device to navigate/control audio. WIRELESS CHARGING Charging Rest This unit will wirelessly charge Qi compatible wireless charging phones when connected to a power outlet. Place Qi compatible device face up on Charging Rest. Check the Charging LED on the iBTW750 for charging status:
Do not place metal phone case or metal objects in the wireless charging area Slow blinking Blue LED: Device is charging properly. Solid Red LED: Device is charged. Rapid blinking Red LED: Device is not charging properly. Reposition device. please confirm blue LED Charging LED Note: The LED may continue to blink slowly when iOS devices are fully charged. CAUTION: Remove metal protective or magnetic case from phone before charging. When charging phone, do not place magnetic-striped or other metal objects on the charger. Doing so could damage the object or this unit. Qi compatible phones with metallic looking nishes will charge normally. Contact Us: 18002882792 For full warranty and full instructions visit: www.ihome.com/support For warranty and full instructions visit: www.ihome.com/support 2019 SDI Technologies, Inc. All rights reserved. Questions? Visit www.ihome.com or call 1-800-288-2792 Toll Free iBTW750-19-0319-A Printed in China