iW18 - Instruction Sheet - English Color: Black text on white paper (1C + 1C) Size: 102 W x 150 H mm Material: 85gsm wood free paper Jun. 24, 2019 OVERVIEW Wireless Charging Area Model: iW18 Bedside/Oce Clock with Dual Charging ALARM SET
- Press to Preview
- Press Again to Arm/Disarm Alarm
- Press & Hold to Set Alarm
(adjust with +/- and press alarm to confirm) SNOOZE
- Press Top Surface to Snooze Alarm
- Press & Hold to Adjust Snooze Duration
(adjust with +/- and press Snooze to confirm) PM Indicator QI Charge Status Indicator Low Backup Battery Indicator Alarm Indicator TIME SET/DIMMER
- Press & Hold to Set Clock
(adjust with +/- and press time to confirm)
- Press to Adjust Display Brightness
(cycle for 5 brightness levels, including OFF) press down whole unit to snooze and to dim display SET
- Press to increase/decrease time & settings Battery Backup Compartment
(for clock accuracy)
*Before use, remove battery pull tab from bottom panel. REAR CONTROLS Connect AC adapter to DC Jack, and plug into outlet. USB Charging
(5V/1A) usb charging DST DC 9V, 2.5A
-1 +1 Auto DST Switch
(Daylight Savings) DC Jack for power supply
(9V/2.5A) WIRELESS CHARGING Supports:
Qi compatible phones (also works with plastic cases up to 3mm thick) AirPods with wireless charging case Place Qi compatible device face up on the charging rest. Charging status will be indicated on display:
Rapid blinking icon:
Device is not charging (reposition device) Slow blinking icon:
Device is charging Solid icon:
Device is fully charged Note: Icon may continue to blink slowly when iOS devices are fully charged. For questions, full instructions, warranty, and additional safety information, please scan the QR code or visit:
www.ihome.com/help/iW18 or call 1-800-288-2792 Toll Free FCC Information This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. FCC ID: EMOIW18 IC: 986B-IW18 This device complies with Part 15 of the FCC Rules, operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. Increase the separation between the equipment and receiver. CAN ICES-3 (B) / NMB-3(B), CAN RSS216 / CNR-216 IC Statement This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canadas licence-exempt RSS(s). Operation is subject to the following two conditions:
(1) This device may not cause interference.
(2) This device must accept any interference, including interference that may cause undesired operation of the device. The device meets the exemption from the routine evaluation limits in section 2.5 of RSS 102 and compliance with RSS-102 RF exposure, users can obtain Canadian information on RF exposure and compliance. This equipment should be installed and operated with a minimum distance of 20 cm between the radiator and your body. Lmetteur/rcepteur exempt de licence contenu dans le prsent appareil est conforme aux CNR dInnovation, Sciences et Dveloppement conomique Canada applicables aux appareils radio exempts de licence. Lexploitation est autorise aux deux conditions suivantes :
(1) Lappareil ne doit pas produire de brouillage;
(2) Lappareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible den compromettre le fonctionnement. Le dispositif rencontre l'exemption des limites courantes d'valuation dans la section 2.5 de RSS 102 et la conformit l'exposition de RSS-102 rf, utilisateurs peut obtenir l'information canadienne sur l'exposition et la conformit de rf. Cet quipement doit tre install et utilis avec une distance minimale de 20 cm entre le radiateur et votre corps. CAUTION - RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE. DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS. The socket-outlet shall be installed near the equipment and shall be easily accessible. 2019 SDI Technologies, Inc. All rights reserved CAUTION: Remove phones metal protective case before charging. Do not place magnetic or metal objects on charger during charging. Qi compatible phones with metallic looking finishes will charge normally. iW18_FCC_062419-A Printed in China