FCC ID: P27F3D100 Alocity All-in-One Access Control Reader

FCC ID: P27F3D100 F3D100 All-in-one Access Control Device Installation Prerequisite Installation to be performed only by certied installer!

Power Sourcing Requirement: PoE+ (802.3at Type 2) 30W!

Unit to be powered by UL294B certied IEEE PoE+ 802.3at Type 2 Power Sourcing Equipment using unshielded cat5e or better cable with a maximum cable length of 330 feet (100 meters)!

A ULC 60839-11-1 Listed power supply with appropriate grade is required to be provided for ULC installations!

Wiegand/OSDP Badge Reader max cable length: 5 ft - 22 AWG (1.5 m)!

Wiegand Panel max cable length: 500 ft - 22 AWG (152 m), 300 ft - 24 AWG (91 m) OSDP Panel max cable length: 4000 ft - 24 AWG (1,219 m), Connect Directly to an Electric Lock Fail Safe Lock There is normally a current owing through the relay on the Fail Safe lock. When the relay is activated, the current own is blocked, and the door lock will open. If the power supply is cut o"

due to a power failure or an external factor, the door will remain open. NC -Burgundy/Yellow COM - Brown/Red F3D100 Pigtail Connect the two NC wires together to the + wire on the lock. !

Connect the two COM (Brown/Red) wires to the

+ wire on the power source.!

Connect the - negative wire from the power source to the - negative on the lock.!

Each wire supports up to 1A, connecting together will allow for up to 2A current to ow.

Fail Secure Lock There is no current owing through the relay on the Fail Secure lock. When the relay is activated, the current ow is opened, and the door lock will open. If the power supply is cut o" due to a power failure or an external factor, the door will remain closed. NO - Orange/Red COM - Brown/Red F3D100 Pigtail Connect the two NO wires together to the + wire on the lock. !

Connect the two COM (Brown/Red) wires to the

+ on the power source.!

Connect the - wire from the power source to the

- on the lock.!

Each wire supports up to 1A, connecting together will allow for up to 2A current to ow.

Connect Power over Ethernet Cable (PoE) The F3D100 uses 802.3at (PoE+).!

Connect a Cat5/6 ethernet cable to the RJ45 located on the pigtail of the F3D100.!

To setup network connection use the Alocity setup app.!

Wiegand Input/Output Wiring Diagram Wiegand Output Wiegand 0 Green / Black Output Wiegand 1 Orange / Balck Input Wiegand 0 Burgundy / Blue Input Wiegand 1 Brown / White Ground Black OSDP Wiring Diagram OSDP / RS485 RS485 A RS485B Ground Orange /White Green / White Black Input for Exit button & Door Contact Sensor Wiring Diagram Inputs Input 1 Input 2 Ground Green / Yellow White Brown / Yellow Max number of face/templates enrolled shall not exceed 10,000!

Ethernet/PoE+ and Wiegand Cable to Reader and Panel are Class II/Power Limited !

Equipment not intended for connection to telephone, or outside wiring as covered by Article 800 in the National Electrical Code, NFPA 70!

FCC This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.!

CAUTION: Any changes or modications to this device not explicitly approved by the manufacturer could void your authority to operate this equipment.!

ATTENTION: Tout changement ou toute modication apports cet appareil sans lapprobation expresse du fabricant risque dinvalider lautorisation relative son utilisation.!

CE Marking Alcatraz AI hereby declares that these facial authentication devices are in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC.

SGS North America Inc. 620 Old Peachtree Road SUITE 100 Suwanee, Georgia 30024 United States Applicant Declaration Applicant Legal Business Name Sercomm Corporation 8F, No. 3-1, YuanQu St., NanKang, Taipei 115, Taiwan Address Grantee Code FCC ID Contact Email Contact Phone Authorized Contact Name P27 P27F3D100 Nick Wu nick_wu@sercomm.com

+886-2-2655-3988, ext:2556 I, the undersigned, certify that I am an authorized signatory for the Applicant and therefore declare;

a) b) c) d) e) in accordance with 47CFR2.911(d), all of the statements herein and the exhibits attached hereto are true and correct to the best of my knowledge and belief. in accepting a Grant of Equipment Authorization issued by a TCB, under the authority of the FCC, as a result of the representations made in this application, the Applicant is responsible for:

(1)

(2)

(3) labeling the equipment with the exact FCC ID as specified in this application, compliance statement labeling pursuant to the applicable rules, compliance of the equipment with the applicable technical rules, if the Applicant is not the actual manufacturer of the equipment, appropriate arrangements have been made with the manufacturer to ensure that production units of this equipment will continue to comply with the FCCs technical requirements. in accordance with 47 CFR 2.909 and KDB394321, the Applicant has read, understood and agrees to accept that they are the responsible party and agree to abide by their responsibilities as specified under 47 CFR 2.909 and KDB394321. in accordance with ISO17065, FCC KDB641163, FCC KDB610077, KDB394321 and RSP-100, the Applicant has read, understood, accepts and agrees to abide by the post market surveillance requirements.

(1)

(2)

(3) the Applicant understands, accepts and agrees that a sample may be requested for surveillance testing. the Applicant shall make provisions to always have a production sample available upon request by SGS, FCC and/or ISED. the Applicant shall, upon request by SGS, at the Applicants expense, provide a production sample of the requested product to SGS, FCC and/or ISED as instructed. The sample shall include all support devices, cables, software, accessories or other hardware or software required for evaluation, review, certification and audit surveillance of products certified by SGS. f) neither the Applicant nor any party to the application is subject to a denial of Federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 862 because of a conviction for possession or distribution of a controlled substance. See 47CFR 1.2002(b) for the definition of a party for these purposes. g) the Applicant has read, understood, accepts and agrees to abide by the SGS North America, Inc.(TCB) terms and conditions. Link to CFRs: https://www.fcc.gov/wireless/bureau-divisions/technologies-systems-and-innovation-division/rules-regulations-title-47 Link to KDBs: https://apps.fcc.gov/oetcf/kdb/index.cfm Link to RSP-100: https://www.ic.gc.ca/eic/site/smt-gst.nsf/eng/sf01130.html Date:November 11, 2021 Applicant Signature:

Print Name:

Title:

*NOTE: This declaration cannot be signed by an Agent, it shall be signed by an authorized person listed in the FCC database Nick Wu Engineer Applicant Declaration Rev:0.0

TO:

Federal Communication Commission Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MID 21046 Regarding FCC ID: P27F3D100 To whom it may concern:

Date: November 11, 2021 We, the undersigned, hereby authorize Kevin Tsai / Deputy Manager of SGS Compliance Certification Services Inc. respect to the FCC ID above, including signing of all documents relating to these matters. Any and all acts carried out by the agent on our behalf shall have the same effect as acts of our own. to act on our behalf in all manners relating to application for equipment authorization with We, the undersigned, hereby certify that we are not subject to a denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 853(a). Where our agent signs the application for certification on our behalf, I acknowledge that all responsibility for complying with the terms and conditions for Certification, as specified by SGS North America, Inc., still resides with Sercomm Corporation. This authorization is valid until further written notice from the applicant. Nick Wu / Engineer Sercomm Corporation Phone: 886-2-2655-3988, ext:2556 E-Mail: nick_wu@sercomm.com

8F, No. 3-1, YuanQu St., NanKang, Taipei 115, Taiwan Regarding:

Confidentiality Request regarding application for FCC ID: P27F3D100 LONG TERM CONFIDENTIALITY Pursuant to 47 CFR Section 0.459 and 0.457 of the commissions rules, the applicant hereby request confidential treatment of the documents listed below, associated with the certification application referenced above. The documents above contain proprietary information not released to the public. Public disclosure of this information may prove harmful to the business of the applicant. SHORT TERM CONFIDENTIALITY Additionally, the applicant requests the following documents be held confidential until the device is marketed or 180 days from the grant date, whichever is less. the Grant Date, the applicant will notify the TCB per FCC KDB 726920 D01 Confidentiality Request Procedures. If the device is marketed within 180 days of To:

SGS North America Inc. 620 Old Peachtree Road SUITE 100 Suwanee, Georgia United States From: Sercomm Corporation Schematic(s) Block Diagrams Operational Descriptions External Photos Internal Photos Test Setup Photos User manual(s) Sincerely, Nick Wu / Engineer Sercomm Corporation Phone: 886-2-2655-3988, ext:2556 E-Mail: nick_wu@sercomm.com