FCC ID: P27MDC450 IC : 5604A-MDC450 Full HD PoE Mini Dome MDC450 Camera Installation Guide Version: 1.0 Copyright 2019. All Rights Reserved. All trademarks and trade names are the properties of their respective owners i FCC ID: P27MDC450 IC : 5604A-MDC450 Package Contents The following items should be included: If any of these items are damaged or missing, please contact your service provider immediately. 1. Mini Dome Camera 2. L Tool
+
3. Mounting Screws: M3*16(5.5*16mm) *3 4. Mounting Template Sheet ii Chapter 1 Introduction FCC ID: P27MDC450 IC : 5604A-MDC450 1 This Chapter provides details of the Mini Dome Camera's features, components and capabilities. Overview The MDC450 is a weather-resistant, HD mini dome camera. It comes with an IP66 rated housing, with a F1.8 large aperture lens, high sensitivity imaging sensor and high power IR LED illumination. The MDC450 displays high quality colorful images in low light conditions, enabling it to view distances of up to 20 meters at night. The MDC450 is an all-in-one camera that has automatic day-night switching, a built-in heater and mechanical Pan/Tilt/Rotate orientation adjustment. Features Dual Video Support: The camera supports H.264 and MJEPG video compression. PoE Support. You can use PoE (Power over Ethernet) to provide power to the Mini Dome Camera, so only a single cable connection is required. IR LED Support. The two built-in infrared LEDs can provide illumination for up to 20 meters. Built-in Heater. The built-in heater ensures that the camera will continue to operate even in extremely cold climates. The heater turns on when the temperature falls below 42F (6C). Security Features User Authentication. If desired, access to live video can be restricted to known users. Users will have to enter their username and password before being able to view the video stream. Password-Protected Configuration. Configuration data can be password protected, so that it only can be changed by the Network Camera Administrator. 1 FCC ID: P27MDC450 IC : 5604A-MDC450 Physical Details - Mini Dome Camera Front Panel - Mini Dome Camera IR LEDs Light Sensor Lens LAN Port Figure 1: Camera Components These are used to provide illumination for night time viewing. Ensure that the two IR LEDs are not obstructed beneath the transparent dome bubble. This is a hardware sensor to detect lux. Ensure that the light sensor is not obstructed beneath the transparent dome bubble. No physical adjustment is required for the lens. Ensure that the lens cover remains clean. Use a standard Ethernet cable (not included) to connect the LAN port of the supplied cable to the gateway. This port supports PoE which provides both power and network connectivity via a single Ethernet cable. 2 FCC ID: P27MDC450 IC : 5604A-MDC450 On (Green) - Power on. Off - No power. Slow Blinking (Green) - The LED blinks during start up. Fast Blinking (Green) - Download mode. On (Blue) - Network connection is available. Blinking (Blue) - The data is transmitting/receiving via network. On (Amber) - Firmware upgrade failure or heater is on. Blinking (Amber) - The firmware is upgrading. Note: If data is being transmitted via LAN, the color of the LED is blue. Status LED
(Green, Amber, Blue) Reset Button Figure 2: Reset Button Reset Button When pressed and held over 15 seconds, the camera reboots and the settings are restored to default values. 3 Chapter 2 Basic Setup FCC ID: P27MDC450 IC : 5604A-MDC450 2 This Chapter provides details on how to setup and mount the Mini Dome Camera. Installation 1. Remove Bubble and Protective Foam a. Use the L tool to remove the three retaining screws and bubble. b. Remove the protective foam. Note: Leave the bubble detached for later access for ceiling mounting. Figure 3: Removing the Bubble 2. Power Up Connect a standard Ethernet cable (not provided) to the LAN port of the camera cable and the LAN port on the gateway Note: Please use the water-proof caps where the Ethernet cable needs to be run with wet environment. Tighten up the caps after connecting the Ethernet cable to the port of the camera. 4 FCC ID: P27MDC450 IC : 5604A-MDC450 Figure 4: Connecting Ethernet Cable with the Caps 3. Check the Status LED The Status LED turns on solid green during startup, which takes 60 to 90 seconds. After startup is completed, the LED begins to blink green. For location of the Status LED, refer to Figure 2. 4. Mount the Camera Place the camera in a desired location near a power source. For details on mounting the camera on the ceiling with the mounting plate, please refer to the later section. 5 FCC ID: P27MDC450 IC : 5604A-MDC450 Mounting the Mini Dome Camera
*Note: Please ensure the Mini Dome Camera is configured and added to the network before permanent mounting. Ceiling Mounting 1. 2. Identify the location where you would like to mount the camera. Using the mounting template included in the box as a guide, drill three mounting holes in the ceiling. If you have not done so already, use the L tool to remove the three screws and the bubble from the camera. Then remove the protective foam as shown. If using the anchors, insert them into the mounting holes. 3. 4. Align the three mounting holes of the camera stand with the three holes, and then mount the camera stand onto the ceiling using the provided screws. Figure 5: Installing the Screws Note: It is recommended that you route the cable through the side opening of the mounting base. 6 FCC ID: P27MDC450 IC : 5604A-MDC450 Figure 6: Routing the Cable 5. Attach the bubble to the camera, and then secure it with the three screws by using the L tool. Note: Use the alignment marks to properly align the camera and bubble while attaching them together. 6. Make sure that the camera is firmly secured to the ceiling. Mounting Suggestion The camera is very sensitive to motion and may even trigger a motion event with the movement of a small tree, bush or other object in the wind. For this reason, be sure to mount the camera in a location where its field of view does not include small trees, bushes or other objects that could move and unintentionally trigger a motion event. 7 Appendix A Specifications Mini Dome Camera FCC ID: P27MDC450 IC : 5604A-MDC450 A Dimensions (DxH) Lens Video Compression Image Resolution Operating Temperature Storage Temperature Network Protocol Network Interface Button Status LED IR LEDs Micro-SD Slot Bluetooth Power 4.33 x 3.62 (110mm x 92mm) F1.8. DFOV 75 H.264 and MJPEG 1080p
-4F to 122F (-20C to 50C)
-40F to 158F (-40C to 70C) TCP/IP, DHCP, SMTP, NTP, HTTP, FTP, RTP, RTSP, UPnP 1 Ethernet 10/100BaseT (RJ45) LAN connection 1 Reset Button 1 Three-colored LED for Power/Network/Heater 2 1 Bluetooth 4.2 RF Module PoE (Power over Ethernet) Regulatory Approvals FCC Statement FederalCommunicationCommissionInterferenceStatement ThisdevicecomplieswithPart15oftheFCCRules.Operationissubjecttothe followingtwoconditions:(1)Thisdevicemaynotcauseharmfulinterference,and
(2)thisdevicemustacceptanyinterferencereceived,includinginterferencethat maycauseundesiredoperation. ThisequipmenthasbeentestedandfoundtocomplywiththelimitsforaClassB digitaldevice,pursuanttoPart15oftheFCCRules.Theselimitsaredesignedto providereasonableprotectionagainstharmfulinterferenceinaresidential installation.Thisequipmentgenerates,usesandcanradiateradiofrequency energyand,ifnotinstalledandusedinaccordancewiththeinstructions,may causeharmfulinterferencetoradiocommunications.However,thereisno 8 FCC ID: P27MDC450 IC : 5604A-MDC450 guaranteethatinterferencewillnotoccurinaparticularinstallation.Ifthis equipmentdoescauseharmfulinterferencetoradioortelevisionreception, whichcanbedeterminedbyturningtheequipmentoffandon,theuseris encouragedtotrytocorrecttheinterferencebyoneofthefollowingmeasures:
Reorientorrelocatethereceivingantenna. Increasetheseparationbetweentheequipmentandreceiver. Connecttheequipmentintoanoutletonacircuitdifferentfromthattowhich thereceiverisconnected. Consultthedealeroranexperiencedradio/TVtechnicianforhelp. FCCCaution:Anychangesormodificationsnotexpresslyapprovedbytheparty responsibleforcompliancecouldvoidtheuser'sauthoritytooperatethis equipment. Thistransmittermustnotbecolocatedoroperatinginconjunctionwithany otherantennaortransmitter. RadiationExposureStatement:
ThisequipmentcomplieswithFCCradiationexposurelimitssetforthforan uncontrolledenvironment.Thisequipmentshouldbeinstalledandoperatedwith minimumdistance20cmbetweentheradiator&yourbody. If protective earthing is used as a safeguard, the instructions shall require connection of the equipment protective earthing conductor to the installation protective earthing conductor ( for emample, by means of a power cord connected to a socket-outlet with earthing connection) CE Approvals The Mini Dome Camera and the Ethernet Mini Dome Camera meet the guidelines of the European Union and comply with the 99/5/EEC and RTTE 99/5EG directives, including the following standards:
EN60950-1 EN55022+55024 EN62311 This is a Class B product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures. 9