FCC ID: 2APA9-CMSXJ38A IMILAB C21

IMILAB C21

IPC038A01

Product Overview

Installation

3. Make sure to position the base unit so that the arrow

is pointing up. Secure the base unit in place by tightening

the screws into the plastic anchors.

Product Instructions

Turning the Device On

IMILAB C21will automatically activate once the power cable is inserted into the

Micro-USB charging port.

IMILAB C21 can be placed on a number of horizontal surfaces, such as a writing desk,

dining table, and coffee table. It can also be mounted on the wall.

Mounted IMILAB C21 on a Wall:

1. Drill two holes on the wall by using the base of the IMILAB C21 as a template. It is

recommended that you mark the locations of the hole with a pencil before drilling.

The diameter of each hole is approximately 6 mm, and the depth is approximately

30 mm.

IMILAB C21

Home Security Camera

User Manual

4. Matching the grooves on the bottom of the camera

unit with the raised area on the base unit. Press down

until the two surfaces are flush, then turn the camera unit

in either direction to lock it in position.

2. Insert the two plastic anchors into the holes on the wall.

RESET

Read this manual carefully before use, and retain it for future reference.

Package Contents: IMILAB C21 x 1, power cable x 1, wall mounting accessories pack x 1,

user manual x 1

Warning:

To avoid any damages or injuries, the device must be securely fastened to the

floor/wall as specified in the installation instructions.

When mounting the security camera on a wall:

Please note that the wall must be able to support at least triple the product's total

weight.

1. If the indicator light is flashing orange, that means the device is activated successfully.

Else, please reset the device.

2. Once the IMILAB C21 is turned on, please do not attempt to rotate its head by force.

If the camera position is incorrect, adjustments can be made through the app.

Status

indicator

MIC

Reset

Hole

Lens

MicroSD Slot

(Can be

revealed by

pushing the

lens upward)

Loudspeaker

Micro-USB

Charging port

RESET

Front View

Rear View

Indicator Light

Steady blue on: connected/device status is normal

Flashing blue: network error

Flashing orange rapidly: waiting for connection

Flashing orange slowly: system upgrade in progress

Installing a MicroSD Card

Make sure that the power to IMILAB C21 is already disconnected. Adjust the camera lens

upward until the MicroSD slot is revealed, then insert the MicroSD card into the slot (the

side with contact points must be facing down).

Note: Please turn off the IMILAB C21‘s power supply before inserting or removing the

MicroSD card. Please use a genuine Micro SD card manufactured by a qualified supplier,

with a reading/writing speed of no less than U1/Class 10. (Maximum support capacity

is 64 GB)

RESET

MicroSD

Install IMILAB Home App

Connect with IMILAB Home app. This product works with IMILAB Home app. Control

your device with IMILAB Home app.

Scan the QR code to download and install the app. You

will be directed to the connection setup page if the app

is installed already. Or search “IMILAB Home” in the app

store to download and install it. Open IMILAB Home app, tap

“+” on the upper right, and then follow prompts to add

your device.

Add Device

Open IMILAB Home app, tap “+” on the upper right. Tap”[-]”and scan the QR code

under the device by your phone, then you can follow the steps to add your device.

Open IMILAB Home app, tap “+” on the upper right. Tap”IMILAB C21”and then you

can follow the steps to add your device.

Hi，

Shared

Please enter the device name to...

Camera

IMILAB Home

Security Cam...

IMILAB Home

Security Cam...

IMILAB Home

Security Cam...

IMILAB Home

Security Cam...

Restore Factory Settings

Press and hold the reset hole with fine needle, then you can hear the “reset succeed”

voice.

Data stored on the MicroSD card is not deleted.

Note: The version of the app might have been updated, please follow the instructions

based on the current app version.

Expandable Memory: MicroSD card (up to 64 GB)

Storage: 108 mm x 76 mm x 76 mm

Operating Temperature: -10 °C to 40 °C

Compatible With: Android 5.0 or iOS 9.0 or above

Wireless Connectivity: Wi-Fi IEEE 802.11 b/g/n 2.4 GHz

Specifications

Name: IMILAB C21

Model: CMSXJ38A

Net Weight: 249 g

Viewing Angle: 105°

Resolution: 2560 x 1440

Input: 5 V 2 A

Precautions

The operating temperature range for this camera is between -10°C and 40°C. Do not

use the camera in environments with temperatures above or below the specified

range.

The camera is a precision electronic product. In order to ensure its normal operation,

do not install the camera in environments with high humidity levels nor allow water

to get into it.

To improve the camera's performance, do not place its lens facing or next to a

reflective surface, such as glass windows or white walls, as this will cause the image

to appear overly bright in areas close to the camera and darker in areas further away,

or cause the camera to produce white images.

Make sure the camera is installed in an area with a strong Wi-Fi signal. Do not place

the camera near the objects that may affect its Wi-Fi signal, such as metal objects,

microwave ovens.

Under normal use of condition, this equipment should be kept a separation distance

of at least 20 cm between the antenna and the body of the user.

FCC Statement

WEEE Information

Changes or modifications not expressly approved by the party responsible for

compliance could void the user's authority to operate the equipment. This device

complies with Part 15 of the FCC Rules.

Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and

(2) This device must accept any interference received, including interference that may

cause undesired operation.

Note: This equipment has been tested and found to comply with the limits for a Class B

digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference in a residential installation. This

equipment generates, uses, and can radiate radio frequency energy, and if not installed

and used in accordance with the instructions, may cause harmful interference to radio

communications.

However, there is no guarantee that interference will not occur in a particular installation.

If this equipment does cause harmful interference to radio or television reception, which

can be determined by turning the equipment off and on, the user is encouraged to try

to correct the interference by one or more of the following measures:

-Reorient or relocate the receiving antenna.

-Increase the separation between the equipment and receiver.

-Connect the equipment into an outlet on a circuit different from that to which the

receiver is connected.

-Consult the dealer or an experienced radio/TV technician for help.

FCC 20cm Statement: This equipment complies with FCC radiation exposure limits set

forth for an uncontrolled environment. This equipment should be installed and

operated with a minimum distance of 20cm between the radiator & your body. This

transmitter must not be co-located or operating in conjunction with any other antenna

or transmitter.

All products bearing this symbol are waste electrical and electronic

equipment (WEEE as in directive 2012/19/EU) which should not be mixed

with unsorted household waste. Instead, you should protect human health

and the environment by handing over your waste equipment to a

designated collection point for the recycling of waste electrical and electronic

equipment, appointed by the government or local authorities. Correct disposal and

recycling will help prevent potential negative consequences to the environment

and human health. Please contact the installer or local authorities for more

information about the location as well as terms and conditions of such collection

points.

EU Declaration of Conformity

Hereby, Shanghai Imilab Technology Co., Ltd. declares that the radio

equipment type IMILAB C21 is in compliance with Directive 2014/53/EU.

Manufacturer: Shanghai Imilab Technology Co., Ltd.

Address: Room 001A, Floor 11, Block 1, No. 588 Zixing Road, Minhang District, Shanghai,

China

For further information, please go to www.imilab.com.

Support: help@imilab.com

版本

V1.0

修改内容

创建图档

修

改

记

录

Cool Gray 11 C

上海创米科技有限公司

038A01

V1.1

20201217

周晓玲

材质：太空梭105g无光铜亚粉

尺寸：75 × 80mm

色相正确、印迹牢固、

套印准确、各色套印

不露杂色，套印误差≤ 0.1mm

模切走位≤±0.5mm

（示例具体以实物为准）

纹理方向

选择正确的

方向图标拖

动到图纸里

Shanghai Imilab Technology Co., Ltd. Agent Authorization Company: Shanghai Imilab Technology Co., Ltd. Address: Room 001A, Floor 11, Block 1, No. 588 Zixing Road, Minhang District, Shanghai, China Product Name: IMILAB C21 Model Number(s): CMSXJ38A Product Description: IMILAB C21 We authorize MiCOM Labs Inc., 575 Boulder Court, Pleasanton, California 94566, USA, to act on our behalf on all matters concerning the certification of above named equipment. We declare that MiCOM Labs Inc. is allowed to forward all information related to the approval and certification of equipment to the regulatory agencies as required and to discuss any issues concerning the approval application. Any and all acts carried out by MiCOM Labs on our behalf shall have the same effect as acts of our own. Signature:

Name:

wang hesong Company: Shanghai Imilab Technology Co., Ltd. Date: 2021-03-12

Shanghai Imilab Technology Co., Ltd. Office of Engineering Technology Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 USA Date: 2021-03-02 Subject; Request for Confidentiality FCC ID: 2APA9-CMSXJ38A To Whom It May Concern, Pursuant to the provisions of the Commissions rules Title 47 Sections 0.457 and 0.459, we are requesting the Commission to withhold the following attachment(s) as confidential documents from public disclosure indefinitely. These documents contain detailed system and equipment descriptions and are considered as proprietary information in operation of the equipment. The public disclosure of these documents might be harmful to our company and would give competitors an unfair advantage in the market. Schematic Diagram Block Diagram Parts List Operational Description Tune-up Procedure External Photos Test Setup Photos Internal Photos User Manual In additional to above mentioned documents, in order to comply with the marketing regulations in Title 47 CFR 2.803 and the importation rules in Title 47 CFR 2.1204, while ensuring that business sensitive information remains confidential until the actual marketing of newly authorized devices, we request Short Term Confidentiality of the following attachment(s);

OR For 45 days, pursuant to Public Notice DA 04-1705. For 180 days pursuant to KDB 726920 D01. It is our understanding that all measurement test reports, FCC ID label format and correspondence during the certification review process cannot be granted as confidential documents and this information will be available for public review once the grant of equipment authorization is issued. Sincerely Shanghai Imilab Technology Co., Ltd. Contact person: wang hesong