FCC ID: 2APA9-CMSXJ40A IMILAB EC3 Lite Outdoor Camera

IMILAB EC3 Lite Outdoor Camera CMSXJ40A 80mm Product Introduction Installing the Device Packing list Note: Please check that the Wi-Fi signal is strong enough before mounting the device. 1. Please mark three holes in the wall rst, and then drill three holes at the positions. Drilling diameter of around 6.0mm; drilling depth of around 30mm. 4. Tighten the nut counterclockwise. Imilab EC3 Lite Outdoor Camera Power Adapter IMILAB EC3 Lite Outdoor Camera User Manual Read this manual carefully before use, and retain it for future reference. IMILAB EC3 Lite Outdoor Camera Wall Mounting Pack User Manual 2. Insert three plastic expansion nuts into the holes. 5. After adjusting the camera to the desired Angle, tighten the bracket nut clockwise. User Manual Overview Microphone Antenna Lens LED Indicator light Reset Button Micro SD Card Slot Speaker 3. Put the base plate on the wall. Secure the base plate by inserting the screws into the expansion nuts. Note: Please ensure that the device is suspended as shown after installation. m m 5 1 1 Read this manual carefully before use, and retain it for future reference. Power supply Connecting the Device Turn on the camera Insert the power supply cable into the camera's power supply port. Connect the other end of the power supply cable to a power source. Indicator Light Steady blue on: connected/device status is normal Flashing blue: network error Flashing orange rapidly: waiting for connection Flashing orange slowly: system upgrade in progress Insert a micro SD card Ensure that the camera is disconnected from the power supply. Use a screwdriver to remove the protective case and expose the micro SD card slot. The contact points of the micro SD card should be facing the same direction as the camera. Insert the micro SD card into the slot. Note:When inserting or removing the micro SD card, please disconnect the camera from the power supply. Please use a micro SD card from a reputable manufacturer. The recommended read and write speed of the micro SD card is at least U1/Class 10. Restoring factory settings Press and hold the reset hole with ne needle, then you can hear the reset succeed voice. Data stored on the MicroSD card is not deleted. Install Imilab Home App Specications FCC Statement Connect with Imilab Home app. This product works with Imilab Home app. Control your device with Imilab Home app. Scan the QR code to download and install the app. Or search Imilab Home in the app store to download and install it. Open Imilab Home app, tap + on the upper right, and then follow prompts to add your device. Name: IMILAB EC3 Lite Outdoor Camera Model: CMSXJ40A Input: 12 V 1 A Resolution: 23041296 Item Dimensions: 1658693 mm Net Weight: 334 g Waterproof: IP66 Operating Temperature: -30~ 60 Wireless Connectivity: Wi-Fi IEEE 802.11 b/g/n 2.4GHz FCC ID: 2APA9-CMSXJ40A Add Device Open Imilab Home app, tap + on the upper right. Tap[-]and scan the QR code on the power line by your phone, then you can follow the steps to add your device. Open Imilab Home app, tap + on the upper right. TapIMILAB EC3 Lite and then you can follow the steps to add your device. Precautions Please enter the device name to... Camera IMILAB Outdoor Security Cam... IMILAB Home Security Cam... Imilab Home My device (6) IMILAB Home Security Cam... IMILAB Home Security Cam... IMILAB Home Security Cam... Note: The version of the app might have been updated, please follow the instructions based on the current app version. The working temperature of the device is -30 to 60. Do not use the device when the temperature is too high or too low. For better results, avoid placing the camera in front of or next or a glass surface, a white-colored wall or other reective surfaces as this may cause the recording to have un-even lighting between the foreground and background or be over-exposed. Please ensure that the device is within Wi-Fi signal coverage. Place it at a location with good Wi-Fi signal strength. Try to avoid placing the device near a metallicobject, a microwave oven or other objects that may cause signal interference. Changes or modications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and

(2) This device must accept any interference received, including interference that may cause undesired operation. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. Thise quipment generates, uses, and canradiate radio frequency energy, and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment o and on, the user is encouraged to try to correct the interference by one or more of the following measures:

-Reorient or relocate the receiving antenna.

-Increase the separation between the equipment and receiver.

-Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected.

-Consult the dealer or an experienced radio/TV technician for help. FCC 20cm Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator & your body. This transmi er must not be co-located or operating in conjunction with any other antenna or transmier. WEEE Disposal and Recycling Information Correct Disposal of this product. This marking indicates that product should not be disposal with other household wastes through out the EU. To prevent possible harm to the environment or human health from uncontrolled waste disposal, recycle it responsibly to promote the sustainable reuse sustainable reuse of material resources. To return your used device, please use the return and collection systems or contact the retailer where the product was purchased. They can take this product for environment safe recycling. Adaptor Statements For pluggable equipment, the socket-outlet (power adaptor) shall be installed near the equipment and shall be easily accessible. Hereby, Shanghai Imilab Technology Co., Ltd. declares that the radio equipment type IMILAB EC3 Lite Outdoor Camera is in compliance with Directive 2014/53/EU. Manufacturer: Shanghai Imilab Technology Co., Ltd. Address: Room 001A, Floor 11, Block 1, No. 588 Zixing Road, Minhang District, Shanghai, China For further information, please go to www.imilab.com. Support: help@imilab.com www.imilabhelp.com 115*80 mm V1.0 V1.1 V1.4 V1.5

31 mm 1 3

. 5 m m IMILAB EC3 Lite Outdoor Camera FCC ID: 2APA9-CMSXJ40A Model: CMSXJ40A PET Material: dumb white PET Pantone cool gray 4C Silk screen colorPantone cool gray 4C A slight deviation is allowed in the dotted line of the sticker invitation, but not too much PET

: 31x13.5mm Material: dumb white PET size: 31x13.5mm Back of the Product

Shanghai Imilab Technology Co., Ltd. Room 001A, Floor 11, Block 1, No. 588 Zixing Road, Minhang District, Shanghai, China Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 USA Date: Feb. 08, 2023 Ref: Attestation Statements Part 2.911(d)(5)(i) Filing FCC ID: 2APA9-CMSXJ40A

[Shanghai Imilab Technology Co., Ltd.] (the applicant) certifies that the equipment for which authorization is sought is not covered equipment prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules. Sincerely,

(Applicant signature)

(wang hesong)

Shanghai Imilab Technology Co., Ltd. Room 001A, Floor 11, Block 1, No. 588 Zixing Road, Minhang District, Shanghai, China Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 USA Date: Feb. 08, 2023 Ref: Attestation Statements Part 2.911(d)(5)(ii) Filing FCC ID: 2APA9-CMSXJ40A

[Shanghai Imilab Technology Co., Ltd.] (the applicant) certifies that, as of the date of the filing of the application, the applicant is not identified on the Covered List as an entity producing covered equipment. Sincerely,

(Applicant signature)

(wang hesong)

Agent Authorization Company: Shanghai Imilab Technology Co., Ltd. Address: Room 001A, Floor 11, Block 1, No. 588 Zixing Road, Minhang District, Shanghai, China Product Name: IMILAB EC3 Lite Outdoor Camera Model Number(s): CMSXJ40A Product Description: IMILAB EC3 Lite Outdoor Camera We authorize MiCOM Labs Inc., 575 Boulder Court, Pleasanton, California 94566, USA, to act on our behalf on all matters concerning the certification of above named equipment. We declare that MiCOM Labs Inc. is allowed to forward all information related to the approval and certification of equipment to the regulatory agencies as required and to discuss any issues concerning the approval application. Any and all acts carried out by MiCOM Labs on our behalf shall have the same effect as acts of our own. Signature:

Date: Feb. 08, 2023 Name:

wang hesong Title:

General Manager Company: Shanghai Imilab Technology Co., Ltd.

Shanghai Imilab Technology Co., Ltd. Room 001A, Floor 11, Block 1, No. 588 Zixing Road, Minhang District, Shanghai, China Office of Engineering Technology Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 USA Subject; Request for Confidentiality FCC ID: 2APA9-CMSXJ40A Date: Jan. 17, 2023 To Whom It May Concern, Pursuant to the provisions of the Commissions rules Title 47 Sections 0.457 and 0.459, we are requesting the Commission to withhold the following attachment(s) as confidential documents from public disclosure indefinitely. These documents contain detailed system and equipment descriptions and are considered as proprietary information in operation of the equipment. The public disclosure of these documents might be harmful to our company and would give competitors an unfair advantage in the market. Schematic Diagram Block Diagram Operational Description Parts List Antenna Specification FCC_Confidential In additional to above mentioned documents, in order to comply with the marketing regulations in Title 47 CFR 2.803 and the importation rules in Title 47 CFR 2.1204, while ensuring that business sensitive information remains confidential until the actual marketing of newly authorized devices, we request Short Term Confidentiality of the following attachment(s);

External Photos Test Setup Photos Internal Photos User Manual For 45 days, pursuant to Public Notice DA 04- 1705. OR For 180 days pursuant to KDB 726920 D01. It is our understanding that all measurement test reports, FCC ID label format and correspondence during the certification review process cannot be granted as confidential documents and this information will be available for public review once the grant of equipment authorization is issued. Sincerely, Signature:

Name: wang hesong Title: General Manager

Shanghai Imilab Technology Co.,Ltd. Room 001A, Floor 11, Block 1, No. 588 Zixing Road, Minhang District, Shanghai ,China Date: Mar. 02, 2023 Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 FCC ID: 2APA9-CMSXJ40A US Agent Attestation Statement / Part 2.91 1(d)(7)

[Shanghai Imilab Technology Co.,Ltd.] certifies, that as of [Mar. 02, 2023], we have designated FCC US Agent, LLC to accept service of process on our behalf for FCC ID: 2APA9-CMSXJ40A.

[Shanghai Imilab Technology Co.,Ltd.], accepts to maintain an agent of service of process in the United States for no less than one year after either the grantee has permanently terminated all marketing and importation of the applicable equipment within the U.S., or the conclusion of any Commission-related administrative or judicial proceeding involving the equipment, whichever is later. FCC US Agent, LLC, accepts as of the date of the filing of this application, the obligation of being the designated agent for the purpose of accepting service of process on behalf of [Shanghai Imilab Technology Co.,Ltd.] for FCC ID: 2APA9-CMSXJ40A. Designated Agent Information:

Company Name: FCC US Agent, LLC FRN: 0033402884 Address: 3722 Illinois Avenue, Saint Charles, IL, 60174, USA Contact Person: Tim Payne Phone: 708-571-3148 Email: Support@FCCUSAgent.com Sincerely, Company: Shan nology Co.,Ltd. Designated Agent: FCC US Agent, LLC Company R bre Designated Agent Representative: Tim Payne Tel: 021-5420149 1/18 Email: wan Signature: Signature: