FCC ID: 2AH25T8920 Handheld Wireless Terminal

1 3 4 6 8 9 10 SIM Micro SD Nano SIM PSAM 7 2 3 5 11 12 Quick Start Guide 1 Front Camera 2 Power Button Short press: Turn on/lock the screen. Long press: When the device is o, press for 2-3 seconds to start the device. When the device is on, press for 2-3 seconds to shut the device down or restart the device. When the system crashes, press for 11 seconds to restart the device. 3 4 5 6 7 8 Scan Button Short press the button to enable scanning function. Volume Button Volume up/down. Function Button You can set a shortcut function. Barcode Scanner For data collection through scanning. Caution: Bright light. Do not stare into beam. Rear Camera For photo taking and 1D/2D barcode scanning. Fingerprint (Optional) Used for ngerprint unlocking devices and related applications. 9 SIM Card Slot/PSAM Card Slot You can insert a SIM card and a PSAM card. 10 Micro SD Card Slot/Nano SIM Card Slot You can insert a Micro SD card and a Nano SIM card. 11 PIN for Extension For connecting related accessories. 12 Back Cover Lock Lift the knob and rotate it to open the battery cover. Note: The battery cover should be installed on the device, otherwise it will aect normal use. Notices Technical specications FCC Statement Safety Warning Connect the AC plug to the AC socket corresponding to the marked input of the power adapter;To avoid injury, unauthorized persons shall not open the power adapter;

This is a Class A product. This product may cause radio interference in living environments.In that case, the user may be required to take adequate measures against interference. Battery replacement:

1.Explosion danger may arise if replacing with the wrong battery!

2.The replaced battery shall be disposed of by maintenance personnel, and please do not throw it into re!

Signicant Safety Instructions Do not install or use the device during lightning storms to avoid the potential risks of lightning shock;

Please turn o the power immediately if you notice abnormal odor, heat or smoke;

Suggestions Do not use the terminal near water or moisture to prevent liquid from falling into the terminal;

Do not use the terminal in extremely cold or hot environments, such as near ames or lit cigarettes;

Do not drop, throw or bend the device;

Use the terminal in a clean and dust-free environment if possible to prevent small items from falling into the terminal;

Please do not use the terminal near medical equipment without permission;

The operating temperature should be-22~55. Statements The Company does not assume responsibilities for the following actions:

Damages caused by use and maintenance without complying with the conditions specied in this guide;

The Company will not assume any responsibilities for the damages or problems caused by optional items or consumables

(rather than the initial products or approved products of the Company). The customer is not entitled to change or modify the product without our consent. The products operating system supports ocial system updates, but if you change the operating system into a third party ROM system or alter the system les by system cracking, it may cause system instability and security risks and threats. Disclaimer As a result of product upgrading, some details in this document may not match the product, and the actual product shall prevail. The Company reserves the right of interpretation of this document. The Company also reserves the right to alter this document without prior notice. For more technical specications, please visit: www.sunmi.com. PRODUCT SAFETY WARNINGS To prevent possible injury, please read all instructions and safety information before you use the product. Operating temperature:-20~55 Storage temperature: -40~70 Battery safety Charge battery only at ambient temperatures ranging from -20C to 60C.

(1) CAUTION: Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type of battery recommended by the manufacturer. Dispose of used batteries according to the battery manufacturers instructions.

(2) CAUTION: RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE.

* The product information listed on this page may be updated from time to time due to product upgrades or other reasons. SUNMI reserves the right to modify the product information and contents on this page without notice. CE certication information (SAR) This device was tested for typical body-worn operations with the back of the handset kept 0mm away. To maintain compliance with RF exposure requirements, use accessories that maintain a 0mm separation distance between the user's body and the back of the handset. The use of belt clips, holsters and similar accessories should not contain metallic components in its assembly. The use of accessories that do not satisfy these requirements may not comply with RF exposure requirements, and should be avoided. If you are using pacemaker, hearing aid, cochlear implant or other device, please use the phone according to the doctors advice. AT BE BG CY CZ DE DK EE ES FI FR GR HU IE IT LT LU LV MT NL PL PT RO SE SI SK UK

(NI) EU Representative :SUNMI France SAS 186,avenue Thiers,69006 Lyon,France This symbol means that it is forbidden to dispose the product of with normal household waste. At the end of the product life cycle, waste equipment should be taken to designated collection points, returned to the distributor when purchasing a new product, or contact your local authority representative for detailed information on WEEE recycling. EU regulatory conformance Conformity CE Hereby,Shanghai Sunmi Technology Co., Ltd.declares that the Smart POS Terminal (Model NO .:T8920is in compliance with the essential requirements and other relevant provisions of RED 2014/53/EU.The full text of the EU declaration of conformity is available at the following internet addresswww.sunmi.com INFORMATION ABOUT THE SOFTWARE The description of accessories and components, including software, which allow the radio equipment to operate as intended, can be obtained in the full text of the EU declaration of conformity at the following internet address: www.sunmi.com RESTRICTIONS OF USE The 5150-5350MHz band is restricted to indoor use in the UK and for the following countries. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment o and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. Caution: The user is cautioned that changes or modications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. RF Exposure Statement (SAR) This device has been tested and meets EU, FCC and IC RSS-102 applicable limits for radio frequency (RF) exposure. For FCC&IC, the minimum separation distance for body-worn accessories is 10mm. ISED Canada compliance statements This device complies with ISED Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le prsent appareil est conforme aux CNR d'ISDE Canada applicables aux appareils radio exempts de licence. L'exploitation est autorise aux deux conditions suivantes:(1) Lappareil ne doit pas produire de brouillage, et (2) Lappareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible den compromettre le fonctionnement. the device for operation in the band 5150-5250 MHz is only for indoor use to reduce the potential for harmful interference to co-channel mobile satellite systems;

Les dispositifs fonctionnant dans la bande 5150-5250 MHz sont rservs uniquement pour une utilisation l'intrieur an de rduire les risques de brouillage prjudiciable aux systmes de satellites mobiles utilisant les mmes canaux. Manufacture Shanghai Sunmi Technology Co., Ltd. Room 505, KIC Plaza, No.388 Song Hu Road, Yang Pu District, Shanghai, China

SIM Micro SD Nano SIM PSAM L2s PRO Smart Mobile Terminal Name: Handheld Wireless Terminal Model: T8920 Input: XV=XA Shanghai Sunmi Technology Co., Ltd. Made in China This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. 3456789012345 IMEI2: 123456789012345 SN: 1234567890123 FCCID: 2AH25T8920 IC: 22621-T8920 lie UN UNUM EU

(a0 NTA

SGS North America Inc. 620 Old Peachtree Road SUITE 100 Suwanee, Georgia 30024 United States Applicant Declaration Applicant Legal Business Name Shanghai Sunmi Technology Co.,Ltd. Address Grantee Code FCC ID Authorized Contact Name Contact Email Contact Phone Room 505, KIC Plaza, No.388 Song Hu Road, Yang Pu District, Shanghai, China 2AH25 2AH25T8920 Fang Lu fang.lu@sunmi.com

+8618501703215 I, the undersigned, certify that I am an authorized signatory for the Applicant and therefore declare;

a) b) c) d) e) in accordance with 47CFR2.911(d), all of the statements herein and the exhibits attached hereto are true and correct to the best of my knowledge and belief. in accepting a Grant of Equipment Authorization issued by a TCB, under the authority of the FCC, as a result of the representations made in this application, the Applicant is responsible for:

labeling the equipment with the exact FCC ID as specified in this application,

(1)

(2) compliance statement labeling pursuant to the applicable rules,

(3) compliance of the equipment with the applicable technical rules, if the Applicant is not the actual manufacturer of the equipment, appropriate arrangements have been made with the manufacturer to ensure that production units of this equipment will continue to comply with the FCCs technical requirements. in accordance with 47 CFR 2.909 and KDB394321, the Applicant has read, understood and agrees to accept that they are the responsible party and agree to abide by their responsibilities as specified under 47 CFR 2.909 and KDB394321. in accordance with ISO17065, FCC KDB641163, FCC KDB610077, KDB394321 and RSP-100, the Applicant has read, understood, accepts and agrees to abide by the post market surveillance requirements.

(1)

(2)

(3) the Applicant understands, accepts and agrees that a sample may be requested for surveillance testing. the Applicant shall make provisions to always have a production sample available upon request by SGS, FCC and/or ISED. the Applicant shall, upon request by SGS, at the Applicants expense, provide a production sample of the requested product to SGS, FCC and/or ISED as instructed. The sample shall include all support devices, cables, software, accessories or other hardware or software required for evaluation, review, certification and audit surveillance of products certified by SGS. f) neither the Applicant nor any party to the application is subject to a denial of Federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 862 because of a conviction for possession or distribution of a controlled substance. See 47CFR 1.2002(b) for the definition of a party for these purposes. g) the Applicant has read, understood, accepts and agrees to abide by the SGS North America, Inc.(TCB) terms and conditions. Link to CFRs: https://www.fcc.gov/wireless/bureau-divisions/technologies-systems-and-innovation-division/rules-regulations-title-47 Link to KDBs: https://apps.fcc.gov/oetcf/kdb/index.cfm Link to RSP-100: https://www.ic.gc.ca/eic/site/smt-gst.nsf/eng/sf01130.html Applicant Signature:

Date: 2022-08-22 Print Name:

Fang Lu Certification Engineer Title:

*NOTE: This declaration cannot be signed by an Agent, it shall be signed by an authorized person listed in the FCC database Applicant Declaration Rev:0.0

Shanghai Sunmi Technology Co.,Ltd. TO:

Federal Communication Commission Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MID 21046 Regarding: 2AH25T8920 To whom it may concern:

Date: 2022-08-22 We, the undersigned, hereby authorize Parlam Zhan to act on our behalf in all manners relating to application for equipment authorization with respect to the FCC ID above, including signing of all documents relating to these matters. Any and all acts carried out by the agent on our behalf shall have the same effect as acts of our own. We, the undersigned, hereby certify that we are not subject to a denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 853(a). Where our agent signs the application for certification on our behalf, I acknowledge that all responsibility for complying with the terms and conditions for Certification, as specified by SGS North America, Inc., still resides with Shanghai Sunmi Technology Co.,Ltd. This authorization is valid until further written notice from the applicant. Name (Printed): Fang Lu Title: Certification Engineer Signature:

On behalf of Company: Shanghai Sunmi Technology Co.,Ltd. Telephone: +8618501703215

Shanghai Sunmi Technology Co.,Ltd. To:

SGS North America Inc. 620 Old Peachtree Road SUITE 100 Suwanee, Georgia United States From: Shanghai Sunmi Technology Co.,Ltd. Room 505, KIC Plaza, No.388 Song Hu Road, Yang Pu District, Shanghai, China Regarding:

Confidentiality Request regarding application for FCC ID: 2AH25T8920 LONG TERM CONFIDENTIALITY Pursuant to 47 CFR Section 0.459 and 0.457 of the commissions rules, the applicant hereby request confidential treatment of the documents listed below, associated with the certification application referenced above. Schematic(s) Block Diagrams Operational Descriptions NII Software Security Info BOM Tune up The documents above contain proprietary information not released to the public. Public disclosure of this information may prove harmful to the business of the applicant. Sincerely, Signature:

Printed Name (on file with the FCC associated with the Grantee Code): Fang Lu Title: Certification Engineer Company Name: Shanghai Sunmi Technology Co.,Ltd.