Quick start Notices 1 2 3 4 5 6 7 8 9 10 11 NFC reader Used for sensing Quick Pass Card. Magnetic card reader Used for reading the information stored in the magnetic stripe of bank card. Front-facing camera (optional) Supports photographing and 1D/2D code quick scanning. Type-C USB Used for charging equipment and debugging by developers. Function Key Used for customized function. Power button Short press: wake up the screen, lock the screen. Long press: long press for 2-3 seconds in power o mode to switch on the device. Long press for 2-3 seconds in normal operation mode to select power o or reboot. Long press for 11 seconds when system is frozenfor automatic reboot. Printer For printing sales slips in power on mode. Indicator lamp Used for indicating the steps for swiping card. IC Card socket Used for inserting the bank chip card. Rear camera Supports photographing and 1D/2D code quick scanning. Extend pins To connect to dock.(Need to buy dock separately) 12 Slide down the metal buckle and take out the Nano SIM 13 14 15 16 SIM card slot (PSAM optional) Used for inserting the SIM Card(PSAM optional) P-SAM card slot Used for inserting the P-SAM Card. Micro SD card slot Used for inserting extend SD card. Nano SIM card slot Used for inserting Nano SIM card. Printing instructions This device supports 58mm thermal paper with the specifications of 570.5mm*40mm. Please open the paper container with the uncovering handl Please do not force open the paper container to avoid print head gear wear;
Feed the paper correctly into the paper container in the direction as shown, and pull some paper outside the cutter;
Close the cover of the paper container to finish printing paper feeding . Note: If the printed paper is blank, please check whether the paper roll has been installed in the correct direction. Safety Warning Connect the AC plug to the AC socket corresponding to the marked input of the power adapter;
To avoid injury, unauthorized persons shall not open the power adapter;
This is a Class A product. This product may cause radio interference in living environments. In that case, the user may be required to take adequate measures against interference. Battery replacement:
1.Explosion danger may arise if replacing with the wrong battery!
2.The replaced battery shall be disposed of by maintenance personnel, and please do not throw it into fire!
Significant Safety Instructions Do not install or use the device during lightning storms to avoid the potential risks of lightning shock;
Please turn off the power immediately if you notice abnormal odor, heat or smoke;
The paper cutter is sharp, please do not touch!
Suggestions Do not use the terminal near water or moisture to prevent liquid from falling into the terminal;
Do not use the terminal in extremely cold or hot environments, such as near flames or lit cigarettes;
Do not drop, throw or bend the device;
Use the terminal in a clean and dust-free environment if possible to prevent small items from falling into the terminal;
Please do not use the terminal near medical equipment without permission. Statements The Company does not assume responsibilities for the following actions:
Damages caused by use and maintenance without complying with the conditions specified in this guide;
The Company will not assume any responsibilities for the damages or problemscaused by optional items or consumables
(rather than the initial products or approvedproducts of the Company). The customer is not entitled to change or modify the product without our consent. The products operating system supports official systemupdates, but if you change the operating system into a third party ROM system or alter the system files by system cracking, it may cause system instability and security risks and threats. Disclaimer As a result of product upgrading, some details in this document may not match the product, and the actual product shall govern. The Company reserves the right of interpretation of this document. The Company also reserves the right toalter this specification without prior notice. Table for Names and Content Identification of Toxic and Hazardous Substances in this Product Toxic or Hazardous Substances and Elements Pb Hg Cd Cr(VII) PBB PBDE Part Name Circuit Board Component Structural Component Packaging Component indicates that the content of the toxic and hazardous substance in all homogeneous materials of the component is below the limit specified in SJ/T 11363-2006. indicates that the content of the toxic and hazardous substance in at least one homogeneous material of the component exceeds the limit stipulated in SJ/T 11363-2006. However, as for the reason, because there is no mature and replaceable technology in the industry at present. The products that have reached or exceeded environmental protection service life should be recycled and reused according to the Regulations on Control and Management of Electronic Information Products, and should not be discarded randomly. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference.
(2) This device must accept any interference received, including interference that may cause undesired operation. FCC ID: 2AH25T6900 NOTE: Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
---Reorient or relocate the receiving antenna.
---Increase the separation between the equipment and receiver.
---Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
---Consult the dealer or an experienced radio/TV technician for help. Body-worn Operation This device was tested for typical body-worn operations. To comply With RF exposure requirements, a minimum separation distance of 5mm must be maintained between the users body and the handset, including the antenna. Third-party belt-clips, holsters, and similar including the antenna. Third-party belt-clips, holsters, and similar accessories used by this device should not contain any metallic components. Body-worn accessories that do not meet these requirements may not comply with RF exposure. This smart POS system meets the government's requirements for exposure to radio waves. The guidelines are based on standards that were developed by independent scientific organizations through periodic and thorough evaluation of scientific studies. The standards include a substantial safety margin designed to assure the safety of all persons regardless of age or health. FCC RF Exposure Information and Statement. The SAR limit of USA (FCC) is 1.6W/kg averaged over one gram of tissue. Device types: T6900 has also been tested against this SAR limit. The highest SAR value reported under this standard during product certification when properly worn on the body is 2.586W/kg10gSAR test distance0mmlimit 4W/kgand 1.262W/kg (1gSAR test distance5mm limit 1.6W/kg). This device was tested for body-worn operations with the back of the handset kept 0mm and 5mm from the body. To maintain compliance with FCC RF exposure requirements, use accessories that maintain a 0mm and 5mm separation distance between the user's body and the back of the handset. The use of belt clips, holsters and similar accessories should not contain metallic components in its assembly. The use of accessories that do not satisfy these requirements may not comply with FCC RF exposure requirements, and should be avoided. Technical features and characteristic Operation Frequency Transmitted GSM 850 GSM 1900 WCDMA BAND II WCDMA BAND IV WCDMA BAND V LTE BAND 2 LTE BAND 4 LTE BAND 5 LTE BAND 7 LTE BAND 17 LTE BAND 41 WIFI BT BLE 5G WIFI NFC 824-849 MHz 1850-1910 MHz 1850-1910 MHz 1710-1755 MHz 824-849 MHz 1850-1910 MHz 1710-1755 MHz 824-849 MHz 2500-2570 MHz 704-716 MHz 2496-2690 MHz 2412-2462 MHz 2402-2480 MHz 2402-2480 MHz 5150MHz-5825MHz 13.56 MHz 32.5 dBm 29.5 dBm 23 dBm 23 dBm 23 dBm 22.5 dBm 22 dBm 23 dBm 23 dBm 23 dBm 23 dBm 13 dBm 5.5 dBm 4 dBm 19 dBm Manufacture Shanghai Sunmi Technology Co., Ltd. Room 505 No.388 Song Hu Road Shanghai, China PANTONE 165C PANTONE Orange 021C 80mm 220mm 400mm 220mm
+2 108g 1 2 3 4 5 6 10 11 13 14 7 8 9 2 1 12 15 16 1 58mm 570.5mm40mm
()
( )
() Pb
(Hg)
(Cd)
(Cr(VII)
(PBB)
(PBDE) 2 3 BaseService ()
() OTA
->
->->->
SJ/T11363-2006 X SJ/T11363-2006 1 2 3 4 5 6 7 8 9 10 11 NFC
() 1D/2D Type-C 2-3 2-3 11 IC 1D/2D
() 12 Nano SIM 13 14 15 16 P-SAMSIM PSAMSIM) P-SAM PSAM Micro SD SD Nano SIM SIM
(SIM:2G/3G/4G:2G/3G/4G:3G/4G) A
()
() ROM QUICK START GUIDE T 6 9 0 0 3887605 K7612000124L 2 0 _ S U _ U E _ N C _ 0 0 9 6 T 1 0 _ U E _ N C _ 0 0 9 6 T