FCC ID: 2AH25T5921 Wireless data POS System

Product Description 1 Extremely easy settings NFC reader Printer Power button Volume button

+

-

Opening handle Type-C USB interface Touch screen Camera SIM Card Slot PSAM Card Slot Flashlight 1D Code Scanner Speaker Extended interface 3 2 Only a few steps to activate an intelligent business device Set 2G/3G/4G: when power o, insert the 2G/3G/4Gcard and then power on.

(Refer to the Technical Specications for the support of cards) Long press the Power Key for 2~3s to activate the backlight of screen, and then operate following the prompts after entering the startup/booting screen for the rst time. 2 modes for accessing the Internet are available. Set WiFi Click "Set" button, activate "WLAN" to enter the WLAN searching screen, and wait it to list all useable WLAN hot spots Click the WLAN to be connected, and enter the access password in case of an encrypted network. Download/use Apps After connected to the Internet, open the App Market, nd, download and install the Apps. Printing instructions This device supports 58mm thermal paper with the specications of 570.5mm*40mm Please open the paper container with the uncovering handle (as shown in Fig.1). Please do not force open the paper container to avoid print head gear wear;

Feed the paper correctly into the paper container in the direction as shown, and pull some paper outside the cutter (as shown in Fig.2);

Close the cover of the paper container to nish printing paper feeding

(as shown in Fig.3). Note: If the printed paper is blank, please check whether the paper roll has been installed in the correct direction. Type-C USB interface FAQ Booting failure (e.g. low battery) Plug the USB cable and charge for 3min;

Check if the screen displays the normal charging status. System crash Long press the Power Key for 11s to reboot. Read the installed Help App for more information Power button Short press: wake up the screen, lock the screen. Long press: long press for 2-3 seconds in power o mode to switch on the device. Long press for 2-3 seconds in normal operation mode to select power o or reboot. Long press for 11 seconds when system is frozenfor automatic reboot. Volume button Volume adjustment (with app support, the button can be set as quick code scan button). Printer For printing sales slips in power on mode. NFC reader Be used for NFC cards like loyalty card. Type-C interface For device recharging and developer debugging. Battery cover Charger & Adapter Power Outlet Camera Supports photographing and 1D/2D code quick scanning. PSAM Card Slot Used for inserting the PSAM Card. SIM Card Slot Note: To prevent system errors, please make sure the device is turned o when you insert or remove the SIM card. Instructions for recharging and battery This device supports charging only by USB cable Connect the 5V adapter to the power supply socket;

Connect the USB cable to the USB interface of the device for recharging;

The screen will display the recharging icon during the recharging process;

If the recharging icon does not appear, please check whether the USB interface is well connected. 1D Code Scanner The 1D Code Scanner is used for reading product bar codes and mobile payment code.

(This Scanner only supports 1D bar codes) Note: don't look straight at the Infrared scanning head to avoid eye injuries. Instructions/Notes for battery This device adopts 7.6V/2580mAh lithium battery; please do not disassemble the battery. In order to protect the battery life, we recommend that yourecharge the device whenever possible, and please do not allow the battery to fully drain before recharging. Precautions Safety Warning Connect the AC plug to the AC socket corresponding to the marked input of the power adapter;

Do not use in the presence of any potentially explosive gas;

To avoid injury, unauthorized persons shall not open the power adapter;

This is a Class A product. This product may cause radio interference in living environments. In that case, the user may be required to take adequate measures against interference. Battery replacement:

1.Explosion danger may arise if replacing with the wrong battery!

2.The replaced battery shall be disposed of by maintenance personnel, and please do not throw it into re!

Signicant Safety Instructions This terminal is a handheld device, and the user shall protect the password from being peered at by others while entering the password;

Do not install or use the device during lightning storms to avoid the potential risks of lightning shock;

Please turn o the power immediately if you notice abnormal odor, heat or smoke;

The paper cutter is sharp, please do not touch!

Suggestions Do not use the terminal near water or moisture to prevent liquid from falling into the terminal;

Do not use the terminal in extremely cold or hot environments, such as near ames or lit cigarettes;

Do not drop, throw or bend the device;

Use the terminal in a clean and dust-free environment if possible to prevent small items from falling into the terminal;

Please do not use the terminal near medical equipment without permission. Statements The Company does not assume responsibilities for the following actions:

Damages caused by use and maintenance without complying with the conditions specied in this guide;

The Company will not assume any responsibilities for the damages or problemscaused by optional items or consumables (rather than the initial products or approvedproducts of the Company). The customer is not entitled to change or modify the product without our consent. The products operating system supports ocial systemupdates, but if you change the operating system into a third party ROM system or alter the system les by system cracking, it may cause system instability and security risks and threats. Disclaimer As a result of product upgrading, some details in this document may not match the product, and the actual product shall govern. The Company reserves the right of interpretation of this document. The Company also reserves the right toalter this specication without prior notice. Technical specications Item Technical Specications Operating system CPU basic frequency RAM FLASH Display Android 7.1 1.4GHZ four cores 1GB LPDDR3 8GB Nand Flash 5.99 inch IPS, resolution 1440720 Touch screen Capacitive two-touch screen Camera 500W AF Wireless data 2GB2/B3/B5/B8 3GWCDMA(B1/B2/B4/B5);EVDO(BC0/BC1) 4GB2/B4/B7/B17/B28 Wi-Fi Build-in Wi-Fi 802.11a/b/g/n2.4G/5G Bluetooth Support of bluetooth 3.0/4.2BLE and iBeacon Keys Interfaces Printer type Printing paper specications NFC Battery Outline dimensions Adapter Power key, volume key Conguration interfaces Type-c, SIM, PSAM, support of OTG Thermal Printer Width 58mm, maximum diameter 40mm mifare/ISO 14443 Type A/B/ISO15693 7.6V/2580mAh L 214mm W 83mm H 49mm OUTPUTDC5V/2A INPUTAC100~240V/0.3A 50/60Hz Adapter Model TPA-23A050200UU01 This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference.

(2) This device must accept any interference received, including interference that may cause undesired operation. FCC ID:2AH25T5921 NOTE: Changes or modications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment o and on, the user is encouraged to try to correct the interference by one or more of the following measures:

---Reorient or relocate the receiving antenna.

---Increase the separation between the equipment and receiver.

---Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected.

---Consult the dealer or an experienced radio/TV technician for help. Body-worn Operation This device was tested for typical body-worn operations. To comply With RF exposure requirements, a minimum separation distance of 1.0cm must be maintained between the users body and the handset, including the antenna. Third-party belt-clips, holsters, and similar including the antenna. Third-party belt-clips, holsters, and similar accessories used by this device should not contain any metallic components. Body-worn accessories that do not meet these requirements may not comply with RF exposure requirements and should be avoided. Specic Absorption Rate (SAR) information:

This wireless phone meets the government's requirements for exposure to radio waves. The guidelines are based on standards that were developed by independent scientic organizations through periodic and thorough evaluation of scientic studies. The standards include a substantial safety margin designed to assure the safety of all persons regardless of age or health. FCC RF Exposure Information and Statement. The SAR limit of USA (FCC) is 1.6W/kg averaged over one gram of tissue. Device types: T5921 has also been tested against this SAR limit. The highest SAR value reported under this standard during product certication when properly worn on the body is 1.218W/kg (1gSAR, test distance:5mm, limit 1.6W/kg), 1.529W/kg(10gSAR, test distance:0mm, limit 4W/kg) and 1.359W/kg(1gSAR, test distance:19mm(power sensor), limit 1.6W/kg). This device was tested for body-worn operations with the back of the handset kept 10mm and 5mm from the body. To maintain compliance with FCC RF exposure requirements, use accessories that maintain a 10mm and 5mm separation distance between the user's body and the back of the handset. The use of belt clips, holsters and similar accessories should not contain metallic components in its assembly. The use of accessories that do not satisfy these requirements may not comply with FCC RF exposure requirements, and should be avoided. Name and content of toxic and harmful substances contained in this product are shown in the following table Toxic and harmful substances and elements Pb

(Hg)

(Cd)

(Cr(VII)

(PBB)

(PBDE) Name of parts Circuit board Shell

:It indicates that the content of toxic and harmful substances in all homoge-

neous materials of this part is below the limit specied in SJ/T11363-2006.

:It indicates that the content of toxic and harmful substances is higher than the limit specied in SJ/T11363-2006 in at least one homogeneous material of this part; however, the the reason why the toxic substance of that part exceeds the limit is that there is no applicable material to replace it currently. For products that have reached or passed the service years for environmental protection, they should be recycled according to Measures for Control and Management of Electronic Information Products and should not be thrown away at will. This product can be used across EU member states. The full text of the EU declaration DOC is available at the following internet addresswww.sunmi.com Manufacture Shanghai Sunmi Technology Co., Ltd. Room 505 No.388 Song Hu Road Shanghai, China List of packaged items Terminal device 1 User's Guide 1 Charger & Adapter 1 USB Cable 1 User Guide T5921

V2 PRO 2018.04.28 2018.07.31 2018.08.01 2018.09.02 V2 PRO 2018.12.12 4GFCCID Wireless data POS System MODEL: T5921 V2 PRO INPUT: 5V 2A Shanghai Sunmi Technology Co.,Ltd. Room 505 No.388 Song Hu Road Shanghai, China Made in China Wireless data POS System MODEL: T5921 V2 PRO INPUT: 5V 2A Shanghai Sunmi Technology Co.,Ltd. Room 505 No.388 Song Hu Road Shanghai, China Made in China FCC ID:2AH25T5921 SN:1234567890123 IMEI:123456789012345 MEID:1234567890123 4mm 3mm 3mm PET+

Shanghai Sunmi Technology Co.,Ltd. File Name QP1665_Block DiagramQP1665_SCH OPBOMTune upTune-Up Procedure Room 505, KIC Plaza, No.388 Song Hu Road, Yang Pu District, Shanghai, China Federal Communications Commission Authorization and Evaluation Division Confidentiality Request regarding application for certification of FCC ID: 2AH25T5921 Pursuant to Sections 0.457 and 0.459 of the Commissions Rules, we hereby request confidential treatment of information accompanying this application as outlined below:

Exhibit Type Block Diagram, Schematics, Operational Description, Parts List, Tune Up The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these materials may be harmful to the applicant and provide unjustified benefits to its competitors. The applicant understands that pursuant to Section 0.457 of the Rules, disclosure of this application and all accompanying documentation will not be made before the date of the Grant for this application. Pursuant to DA04-1705 June 15, 2004 of the Commissions public notice, we also request temporary confidential treatment of information accompanying this application as outlined below:

Exhibit Type NA Sincerely, File Name NA Rev 11/20/07

Shanghai Sunmi Technology Co.,Ltd. Room 505, KIC Plaza, No.388 Song Hu Road, Yang Pu District, Shanghai, China Federal Communications Commission Authorization and Evaluation Division 1435 Oakland Mills Road Columbia, MD 21046 Date: 2019/1/16 SUBJECT: FCC Application for 2AH25T5921 To Whom It May Concern:

We, the undersigned, hereby authorize _ East china institute of Telecommunications __ on our behalf, to apply to the Federal Communications Commission on our equipment. Any and all acts carried out by _ East china institute of Telecommunications __ on our behalf shall have the same effect as acts of our own. This is to advise that we are in full compliance with the Anti- Drug Abuse Act. We, the applicant, are not subject to a denial of federal benefits pursuant to Section 5301 of the Anti-Drug Act of 1988, 21 USC853a, and no party to the application is subject to a denial of federal benefits pursuant to that section. Regards,

(Must be signed by the person that is listed on the FCC Website)

\\M1020\project\2018 \\I18D00233\\\POA_Letter_140225.docx

Shanghai Sunmi Technology Co.,Ltd. Date: 2019/01/16 DTS-UNll Device Declaration Letter To whom it may concern:

We have declared below featured for FCC equipment authorization, Device FCC ID: 2AH25T5921

(1) DFS Device -Master , Client with Radar detection capability r Client without radar detection capability, N/A Active I Passive Scanning, adhoc mode access point capability Frequency Band Active Scanning (the Passive scanning Ad Hoc Mode Access point

(MHz) device can transmit a

(where the device or WIFI Direct capability 2412-2462MHz probe (beacon)) Yes, No is can listen only Yes, No capability Yes, No Yes, No 5150-5250MHz Yes, No with no probes) Yes, No Yes, No Yes, No 5250 - 5350MHz Yes, No Yes, No Yes, No Yes, No 5470 - 5725MHz Yes, No Yes, No Yes, No Yes, No 5725 - 5850MHz Yes, No Yes, No Yes, No Yes, No

(3) Country code selection ability - Yes, No If yes, pls explain how it was implemented: (pls also help to provide detail of options for each country selection)

(4) Meet 15.202 requirement - Yes, No,pls check below:

A master device is defined as a device operating in a mode in which it has the capability to transmit without receiving an enabling signal. In this mode it is ableto select a channel and initiate a network by sending enabling signals to other devices A client device is defined as a device operating in a mode in which the transmissions of the device are under control of the slave. A device in client mode is not able to initiate a network.

(5) For client devices that have software configuration control to operate In different modes (active scanning in some and passive scanning in others) in different bands (devices with multiple equipment classes or those that operate on non-DFS frequencies) or modular devices which configure the modes of operations through software, the application must provide software and operations description on how the software and / or hardware is implemented to ensure that proper operations modes cannot be modified by end user or an installer. Apply, "Yes, please see SW security Description". No Apply, (If apply, pls help to provide explanation on it was implement. and how software was controlled)