AR2000 Bk-BGL User Manual SLIM BLUETOOTH SOUNDBAR AR2000BK-BGL 1. Power ON/OFF button 2. / ( Skip Forward/Backward ) button 3. EQ ( Equalizer ) button 4. BASS +/- buttons 5. ( Mute ) button 6. ( Play/Pause ) button 7. SOURCE button 8. VOL ( Volume ) +/- buttons 9. TREBLE +/- buttons Battery Installation for Remote Control
- First Time Use Remove and discard the insulation tab as figure on the right.
- If the battery is consume, replace it as below:
1. Push and slide out the battery holder as figure 1 below. 2. Replace the battery with a new CR2025 button cell as the polarity markings on the rear of the Remote Control. 3. Close the battery holder. Soundbar SLIM BLUETOOTH SOUNDBAR AR2000BK-BGL User Manual AUX IN Playback:
Press the button on the remote control to turn the sound OFF. Press again to resume sound. Press the Volume+/- button on the unit or the VOL+/- button on the remote control to adjust the volume level. Press the Bass+/- button on the remote control to adjust the bass level. Press the Treble+/- button on the remote control to adjust the treble level. Press the EQ button on the remote control to switch the equilibrium between POP/JAZZ/CLASSIC/ROCK/NORMAL. Examples of RCA AUX IN sources are television sets, DVD players. and VCR players. RCA AUX IN Connection:
1. Connect RCA cord (included) between your audio player and the AUX-IN 1 Jacks on the top of the Soundbar. 2. Press the SOURCE/ button on the unit or the button on the remote control to turn on the Soundbar. 3. Press the SOURCE/ button on the unit or the SOURCE button on the remote control repeatedly until the indicator turns Green. 4. Set your personal external player to play. RCA AUX IN Playback:
Press the button on the remote control to turn the sound OFF. Press again to resume sound. Press the Volume+/- button on the unit or the VOL+/- button on the remote control to adjust the volume level. Press the Bass+/- button on the remote control to adjust the bass level. Press the Treble+/- button on the remote control to adjust the treble level. Press the EQ button on the remote control to switch the equilibrium between POP/JAZZ/CLASSIC/ROCK/NORMAL. On a Blackberry Go to SETTINGS>OPTIONS>BLUETOOTH Enable BLUETOOTH Mounting on wooden wall 22.4 inches Screw Screw The volume may be too low. Try increasing the volume by pressing Volume+ button on the speaker or VOL+ button on the remote control. The connected device might not be in playback mode. Play music the connected Bluetooth device. The sound output of the connected device is weak. Increase the volume of the connected Bluetooth device. On an Android Phone Go to SETTINGS>BLUETOOTH>MENU>Search for devices(Make sure Bluetooth is turned ON) On other Cell Phone/Devices Review the instruction manual that came with your phone/device. 1. Mark the position of the mounting screws on the wall using a pencil. 2. Drill the supplied screws directly into the made on the wall and leave approx. 0.3 inch length to hook the sound bar. marks that you have 3. Put the sound bar onto the mounting screws. Make sure they are firm and stable. Mounting on brick wall Fixing Plug Screw 22.4 inches Fixing Plug Screw 1. Mark the position of the mounting screws on the wall using a pencil. 2. Drill 2 holes by a powerful electric drill ( Not Supplied ). 3. Insert the supplied fixing plug and hammer into the holes. 4. Secure the supplied screws into the fixing plugs and length to hook the sound bar. leave approx. 0.3 inch 5. Put the sound bar onto the mounting screws. Make sure they are firm and stable. The volume may be too high. Try reducing the volume by pressing Volume- button on the speaker or VOL- button on the remote control. The sound output of the connected device may be too high. Try reducing the volume of the connected Bluetooth device. Make sure no other devices are connected to the Soundbar and try the connection again. If a device was connected to the speaker, unpair it before connecting your new device.Do this using your Bluetooth device's Bluetooth menu. Power adapter RCA cable Remote control Fig.1 Fig.2 Fig.3 2 screws 2 plastic wall plugs 3.5mm auxiliary cord FRONT VIEW SIDE VIEW To Turn the Unit ON Connect the supplied power adapter to the DC IN jack. Then press the SOURCE/ button on the unit or the button on the remote control. To Turn the Unit OFF Press and hold the SOURCE/ button on the unit or press the button on the remote control. 1. Press the SOURCE/ button on the unit or the button on the remote control to turn on the Soundbar. 2. Press the SOURCE/ button on the unit or the SOURCE button on the remote control repeatedly until the indicator turns Blue. 3. Keep the unit and the Bluetooth enabled device within 3 feet of each other during the pairing process. 4.Set your mobile phone or other Bluetooth enabled device to search for Bluetooth devices. BLUETOOTH Playback:
Press the button to pause playing track. Press again to resume playing. Press the or button on the remote control to skip to next or previous track. Press the button on the remote control to turn the sound OFF. Press again to resume sound. Press the Volume+/- button on the unit or the VOL+/- button on the remote control to adjust the volume level. Press the Bass+/- button on the remote control to adjust the bass level. Press the Treble+/- button on the remote control to adjust the treble level. Press the EQ button on the remote control to switch the equilibrium between POP/JAZZ/CLASSIC/ROCK/NORMAL. 1.Speaker 2.Remote Sensor 3.Indicator 4.Volume +/- Button 5.AUX-IN 2 Jack 6.SOURCE/ (Standby) Button TOP VIEW 7.RCA Jacks 8.DC IN Jack within 3 feet Examples of AUX IN sources are personal audio players and computers. On an iPhone AUX IN Connection 1. Connect a 3.5 mm auxiliary cord (included) between your audio player and the AUX-IN 2 Jack on the right side of the Soundbar. 2. Press the SOURCE/ button on the unit or the button on the remote control to turn on the Soundbar. 3. Press the SOURCE/ button on the unit or the SOURCE button on the remote control repeatedly until the indicator turns Orange. 4. Set your personal audio player to play. Go to SETTINGS>GENERAL>BLUETOOTH
(Make sure Bluetooth is turned ON)