FCC ID: N6C-SXNEWAH Embedded Wireless Module

Since this module is not sold to general end users directly, there is no user manual of For the details about this module, please refer to the specification sheet of module. This module should be installed in the host device according to the interface specification User Manual module.

(installation procedure). FCC Notice undesired operation. This device complies with Part 15 of FCC Rules. Operation is subject to the following two conditions:

(1) this device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that may cause List of applicable FCC rules This device complies with below part 15 of the FCC Rules. Part 15 Subpart C Additional testing, Part 15 Subpart B disclaimer The modular transmitter is only FCC authorized for the specific rule parts (i.e., FCC transmitter rules) listed on the grant, and the host product manufacturer is responsible for compliance to any other FCC rules that apply to the host not covered by the modular transmitter grant of certification. The final host product still requires Part 15 Subpart B compliance testing with the modular transmitter installed. professionally. Summarize the specific operational use conditions This module designed for mounting inside of the end product by end product manufacturer Therefore, it complies with the antenna and transmission system requirements of 15.203. RF exposure considerations This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment and meets the FCC radio frequency (RF) Exposure Guidelines. This equipment should be installed and operated keeping the radiator at least 20cm or more away from persons body. Co-Location Rule This transmitter must not be co-located or operated in conjunction with any other antenna or transmitter. Label and compliance information Following information must be indicated on the host device of this module. Contains Transmitter Module FCC IDN6C-SXNEWAH Or Contains FCC IDN6C-SXNEWAH FCC CAUTION FCC CAUTION Antenna List The following statements must be described on the user manual of the host device of this module;

Changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. Vender Model No. Antenna Type Antenna Gain [dBi]

STAF T16-062-1022 ethertronics 9000984-XLPDNB PSA (Walsin) RFDPA131000SMRB801 ROD Invax AN0915-13D01BSM SaemON Technology SMEG0900DEN PCB ROD ROD ROD 3.0 3.4 3.01 2.00 1.26 Limited module procedures This module needs to supply a regulated voltage to VDDFEM from host device. ISED Notice This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canadas licence-exempt RSS(s). Operation is subject to the following two 1. This device may not cause interference. conditions:

of the device. 2. This device must accept any interference, including interference that may cause undesired operation Lmetteur/rcepteur exempt de licence contenu dans le prsent appareil est conforme aux CNR dInnovation, Sciences et Dveloppement conomique Canada applicables aux appareils radio exempts de licence. Lexploitation est autorise aux deux conditions suivantes :

1. Lappareil ne doit pas produire de brouillage;

2. Lappareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible den compromettre le fonctionnement. Label and compliance information The following information must be indicated on the host device of this module. Contains Transmitter Module IC: 4908A-SXNEWAH Or Contains IC: 4908A-SXNEWAH RF exposure considerations This equipment complies with ISED radiation exposure limits set forth for an uncontrolled environment and meets RSS-102 of the ISED radio frequency (RF) Exposure rules. This equipment should be installed and operated keeping the radiator at least 20cm or more away from persons body. Cet quipement est conforme aux limites dexposition aux rayonnements nonces pour un environnement non contrl et respecte les rgles dexposition aux frquences radiolectriques (RF) CNR-102 de lISDE. Cet quipement doit tre install et utilis en gardant une distance de 20 cm ou plus entre le radiateur et le corps humain. Antenna Type This radio transmitter (4908A-SXNEWAH) has been approved by Innovation, Science and Economic Development Canada to operate with the antenna types listed below, with the maximum permissible gain indicated. Antenna types not included in this list that have a gain greater than the maximum gain indicated for any type listed are strictly prohibited for use with this device. Antenna Type Rod Antenna PCB Antenna Gain 3.4dBi 3.0dBi Impedance 50ohms 50ohms Le prsent metteur radio (4908A-SXNEWAH) a t approuv par Innovation, Sciences et Dveloppement conomique Canada pour fonctionner avec les types d'antenne numrs ci-dessous et ayant un gain admissible maximal. Les types d'antenne non inclus dans cette liste, et dont le gain est suprieur au gain maximal indiqu pour tout type figurant sur la liste, sont strictement interdits pour l'exploitation de l'metteur. Type d'antenne Antenne tige Antenne PCB Gain 3.4dBi 3.0dBi Impedance 50ohms 50ohms Limited module procedures This module needs to supply a regulated voltage to VDDFEM from host device. Ce module doit fournir une tension rgule VDDFEM partir du priphrique hte.

Since this module is not sold to general end users directly, there is no user manual of For the details about this module, please refer to the specification sheet of module. This module should be installed in the host device according to the interface specification User Manual module.

(installation procedure). FCC Notice undesired operation. This device complies with Part 15 of FCC Rules. Operation is subject to the following two conditions:

(1) this device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that may cause List of applicable FCC rules This device complies with below part 15 of the FCC Rules. Part 15 Subpart C Additional testing, Part 15 Subpart B disclaimer The modular transmitter is only FCC authorized for the specific rule parts (i.e., FCC transmitter rules) listed on the grant, and the host product manufacturer is responsible for compliance to any other FCC rules that apply to the host not covered by the modular transmitter grant of certification. The final host product still requires Part 15 Subpart B compliance testing with the modular transmitter installed. professionally. Summarize the specific operational use conditions This module designed for mounting inside of the end product by end product manufacturer Therefore, it complies with the antenna and transmission system requirements of 15.203. RF exposure considerations This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment and meets the FCC radio frequency (RF) Exposure Guidelines. This equipment should be installed and operated keeping the radiator at least 20cm or more away from persons body. Co-Location Rule This transmitter must not be co-located or operated in conjunction with any other antenna or transmitter. Label and compliance information Following information must be indicated on the host device of this module. Contains Transmitter Module FCC IDN6C-SXNEWAH Or Contains FCC IDN6C-SXNEWAH FCC CAUTION FCC CAUTION Antenna List The following statements must be described on the user manual of the host device of this module;

Changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. Vender Model No. Antenna Type Antenna Gain [dBi]

STAF T16-062-1022 ethertronics 9000984-XLPDNB PSA (Walsin) RFDPA131000SMRB801 ROD Invax AN0915-13D01BSM SaemON Technology SMEG0900DEN PCB ROD ROD ROD Taoglas IS.05.B.3010021 thread-mount 3.0 3.4 3.01 2.00 1.26 2.40 Limited module procedures This module needs to supply a regulated voltage to VDDFEM from host device. ISED Notice This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canadas licence-exempt RSS(s). Operation is subject to the following two 1. This device may not cause interference. conditions:

of the device. 2. This device must accept any interference, including interference that may cause undesired operation Lmetteur/rcepteur exempt de licence contenu dans le prsent appareil est conforme aux CNR dInnovation, Sciences et Dveloppement conomique Canada applicables aux appareils radio exempts de licence. Lexploitation est autorise aux deux conditions suivantes :

1. Lappareil ne doit pas produire de brouillage;

2. Lappareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible den compromettre le fonctionnement. Label and compliance information The following information must be indicated on the host device of this module. Contains Transmitter Module IC: 4908A-SXNEWAH Or Contains IC: 4908A-SXNEWAH RF exposure considerations This equipment complies with ISED radiation exposure limits set forth for an uncontrolled environment and meets RSS-102 of the ISED radio frequency (RF) Exposure rules. This equipment should be installed and operated keeping the radiator at least 20cm or more away from persons body. Cet quipement est conforme aux limites dexposition aux rayonnements nonces pour un environnement non contrl et respecte les rgles dexposition aux frquences radiolectriques (RF) CNR-102 de lISDE. Cet quipement doit tre install et utilis en gardant une distance de 20 cm ou plus entre le radiateur et le corps humain. Antenna Type This radio transmitter (4908A-SXNEWAH) has been approved by Innovation, Science and Economic Development Canada to operate with the antenna types listed below, with the maximum permissible gain indicated. Antenna types not included in this list that have a gain greater than the maximum gain indicated for any type listed are strictly prohibited for use with this device. Le prsent metteur radio (4908A-SXNEWAH) a t approuv par Innovation, Sciences et Dveloppement conomique Canada pour fonctionner avec les types d'antenne numrs ci-dessous et ayant un gain admissible maximal. Les types d'antenne non inclus dans cette liste, et dont le gain est suprieur au gain maximal indiqu pour tout type figurant sur la liste, sont strictement interdits pour Antenna Type Rod Antenna PCB Antenna Gain 3.4dBi 3.0dBi thread-mount Antenna 2.40dBi l'exploitation de l'metteur. Type d'antenne Antenne tige Antenne PCB Gain 3.4dBi 3.0dBi Antenne montage filet 2.40dBi Impedance 50ohms 50ohms 50ohms Impedance 50ohms 50ohms 50ohms Limited module procedures This module needs to supply a regulated voltage to VDDFEM from host device. Ce module doit fournir une tension rgule VDDFEM partir du priphrique hte.

1 2 3 4 l a i t n e d i f n o C A B C D E F

. c n I

, l y g o o n h c e t x e l i s A B C D E F Model:SX-NEWAH FCC ID:N6C-SXNEWAH IC:4908A-SXNEWAH R-NZ silex technology,Inc. Fabriqu au Japon Made in Japan XXXXXX XXXXXX 7 2 20.5 3.1 Note EMI

(The EMI label must be attached within the shield plate.) MATERIAL FINISH SCALE APPROVED 2 : 1 CHECKED SHEET K.Okazaki T.Minobe SIZE A4 1/1 Label Position Drawing KP100420XX TITLE DWG No. FIRST EDITION REVIS 2019.12.25 T.Kimoto DATE DESIGN CHANGE OF CONTENTS 1 2 3

Se

silex UL Verification Services Inc. 47173 Benicia Street, Fremont, CA 94538 Applicant: Silex Technology, Inc. FCC ID: N6C-SKNEWAH Seb sELAueiuoee We, the undersigned, hereby authorize Shuichi Ohyama of Consumer Technology Division, UL Japan, Inc. to act on our behalf in all manners relating to application for equipment authorization, including signing of all documents relating to these matters. Any and all acts carried out by UL Japan, Inc. on aM BARR Meee RO mere Tne We, the undersigned, hereby certify that we are not subject to a denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. Sam This authorization is valid until further written notice from the applicant. The application for the subject equipment has not been submitted to another TCB for certification. Sincerely Yours, Yoshi o Nakai Silex _chnology, Inc. Date: December 8, 2020 technology

sitlex SUN CR iM B uC s OMIM CNM -TORUU Tee ORME CM cere m lI Britcocm im Tre Ts eti requirements of the applicable rules of FCC. Please refer to the test report submitted with this application. Thank you for your attention to this matter. Test Re ort (DTS) RF Ex osure External Photo Internal Photo Loom erie Label Drawing/ Location Block Dia am NEE eP Aer HCOY NN Schematic Diagram Parts List CL kd C x C O O CJ Federal Communication Commission Equipment Authorization Division FANS iec ss Mne uo em sy e-Te(ONT 7435 Oakland Mills Road Columbia, Maryland 21046 FCCID : N6C-SXNEWAH Applicant : Silex Technology, Inc. SKORWcoum ia Eye ew eoe This is to request a Class II permissive change for FCC ID: N6C-SXNEWAH, originally granted on 05/21/2020. We changed the following points from the original model.

" Add 1 type of antenna (IS.05.B.3010021) Meanwhile we submit the following documents related to this change. There is no change before and after change except for these documents. Yosh i Nakai Silex echnology, Inc. Request for Class II Permissive Change December 8, 2020 technology

silex LODE Cubiteclalesp meio m's eocm ole 47173 Benicia Street, Fremont, CA 94538 FCCID :N6C-SXNEWAH Applicant: Silex Technology, Inc. To whom it may concern:

Please be advised Embedded Wireless Module, model: SX-NEWAH is designed for mounting inside of RCO Cem LACH BC UmUCIM Co mE LOO iel hae MOROCCO IMC TTR LBM ICICI mTItsl transmission system requirements of 15.203. Thank you for your attention to this matter. Sincerely, Yoshin akai Silex e hnology, Inc. Declaration Letter of professional install Date: December 8, 2020 technology

silex UL Verification Services Inc. 47173 Benicia Street, Fremont, CA 94538 Applicant: Silex Technology, Inc. FCC ID :N6C-SXNEWAH SOO BiaNCL ANE Nuon MEM ana eee OTIC ECC MMOCRUS NTC UE Memeo iMy MICRO ve tare the FCC rules 0.457 and 0.459:

Theory of Operation The application contains technical information which we deem to be trade secrets and proprietary. If made public, the information might be used to the disadvantage of the applicant in the market place. Thank you for your attention to this matter. Yos 'o Nakai Silex hnology, Inc. Request for Confidentiality Date: December 8, 2020 echnology

silex technology Request for Limited Modular Transmitter Approval May 15, 2020 FCC ID :N6C-SXNEWAH Applicant: Silex Technology, Inc. This transmitter, model: SX-NEWAH is designed by us. It complies with the modular transmitters basic requirements (Item 1 to 8) in FCC Part 15 Subpart C Section 15.212 as indicated below:

Modular Approval Checklist:

Modular approval requirement Yes_ | No

(1) Have its own RF shielding. Xx L]

(2) Have buffered modulation/data inputs. L |

(3) Have its own power supply regulation. | L] Xx]

This module has the power supply regulator. However the one of input voltages to RF part dont go through the regulator. The stable voltage will be supplied by end product. Therefore end product will be required to have the power supply regulator.

(4) Comply with the antenna and transmission system | [_] XxX requirements of 15.203, 15.204(b) and 15.204(c). Antenna connector of module is unique but connector between cable and some antenna is not unique. Therefore only professional installer can install the module and antennas.

(5) Tested in a stand-alone configuration. xX] L]

Unless the transmitter module will be battery powered, it must comply with the AC line conducted requirements found in FCC 15.207. AC or DC power lines and data input/output lines connected to the module must not contain ferrites, unless they will be marketed with the module. The length of these lines shall be the length typical of actual use or, if that length is unknown, at least 10 centimeters to insure that there is no coupling between the case of the module and supporting equipment. Any accessories, peripherals, or support equipment connected to the module during testing shall be unmodified and commercially available.

(6) Equipped with either a permanently affixed label or must be | X] L]

capable of electronically displaying its FCC ID. If the FCC ID is not visible when the module is installed inside another device, then the outside of the device into which the module is installed must also display a label referring to the enclosed module.

(7) Comply with any specific rules or operating requirements | [X] L]

that ordinarily apply to a complete transmitter and the manufacturer must provide adequate instructions along with the module to explain any such requirements.

(8) Comply with any applicable RF exposure requirements in its | [x] L |

final configuration: The modular transmitter complies with FCC radiation exposure requirement. L bowaf Toshiro Kometani Silex Technology, Inc.

silex PUP Cu Ree BUN NR R CoRR Bitte Ro taneieBeree Crane made public, the information might be used to the disadvantage of the applicant in the market place. PRU eo PR OM He Ty MORIN CBr nce Sincerely, UL Japan, Inc. 4383-326 Asama-cho, Ise-shi, WC CRIP ERE TT FCCID : N6C-SXNEWAH Applicant: Silex Technology, Inc. To whom it may concern:

aC ERC ese MSE BC ROM SOBRE rem Mm EIR CM EM COM tRt ck d the Grant of Equipment Authorization based on the FCC rules 0.457 and 0.459:

External Photos Internal Photos Test Setup Photos User Manual Toshiro Kometani Silex Technology, Inc. Request for Short-Term Confidentiality Date: December 5, 2019 technology