PF-SDMGN Users Manual June 25, 2012 PF-SDMGN Users Manual 1. Hardware specifications/Compliance ...................................................2 2. System Requirements (for the install) ..................................................5 3. Setup ..............................................................................5 1/ 1. Hardware specifications/Compliance FCC IDN6C-PFSDMGN IC No4908B-PFSDMGN PF-SDMGN Users Manual NOTICE This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
-Reorient or relocate the receiving antenna
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help. This Class B digital apparatus complies with Canadian ICES-003. Cet appareil numrique de la classe B est conforme la norme NMB-003 du Canada. This device complies with Part 15 of FCC Rules and Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of this device. Le prsent appareil est conforme aux la partie 15 des rgles de la FCC et CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorise aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible d'en compromettre le fonctionnement. This transmitter must not be co-located or operated in conjunction with any other antenna or transmitter. This equipment complies with FCC/IC radiation exposure limits set forth for an uncontrolled environment and meets the FCC radio frequency (RF) Exposure Guidelines in Supplement C to OET65 and RSS-102 of the IC radio frequency (RF) Exposure rules. This equipment should be installed and operated keeping the radiator at least 20cm or more away from persons body (excluding extremities: hands, wrists, feet and ankles). Cet quipement est conforme aux limites dexposition aux rayonnements nonces pour un environnement non contrl et respecte les rgles les radiolectriques (RF) de la FCC lignes directrices d'exposition dans le Supplment C OET65 et dexposition aux frquences radiolectriques (RF) CNR-102 de lIC. Cet quipement doit tre install et utilis en gardant une distance de 20 cm ou plus entre le dispositif rayonnant et le corps (
lexception des extrmits : mains, poignets, pieds et chevilles). Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum
(or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication. Conformment la rglementation d'Industrie Canada, le prsent metteur radio peut fonctionner avec une antenne d'un type et d'un gain maximal (ou infrieur) approuv pour l'metteur par Industrie Canada. Dans le but de rduire les risques de brouillage radiolectrique l'intention des autres utilisateurs, il faut choisir le type d'antenne et son gain de sorte que la puissance isotrope rayonne quivalente (p.i.r.e.) ne dpasse pas l'intensit ncessaire l'tablissement d'une communication satisfaisante. 2/ PF-SDMGN Users Manual This radio transmitter (identify the device by certification number, or model number if Category II) has been approved by Industry Canada to operate with the antenna types listed below with the maximum permissible gain and required antenna impedance for each antenna type indicated. Antenna types not included in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device. Le prsent metteur radio (identifier le dispositif par son numro de certification ou son numro de modle s'il fait partie du matriel de catgorie I) a t approuv par Industrie Canada pour fonctionner avec les types d'antenne numrs ci-dessous et ayant un gain admissible maximal et l'impdance requise pour chaque type d'antenne. Les types d'antenne non inclus dans cette liste, ou dont le gain est suprieur au gain maximal indiqu, sont strictement interdits pour l'exploitation de l'metteur. Antenna information: Omni-directional Gain 1.5dBi FCC WARNING Changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. Manual and Product Labeling information To The End User The end user manual shall include all required regulatory information/warning as show in this manual. And when this module is installed in the host product, you must include a "Contain FCC ID : N6C-PFSDMGN"
and a Contain IC: 4908B-PFSDMGN in the label of the host product.
PF-SDMGN Users Manual Operating environment Temperature-20 to +85, -4F to +185F Storage environment supply voltage Host I/F IEEE802.11b Humidity20% to 85%
Temperature-40C to +90C, -40F to +194F Humidity20% to 85%
3.3V 5%
SDIO V2.0 Frequency : 2412MHz~2462MHz Transmission system DS-SS Transmission speed 1M/2M/5.5M/11M Automatic detection Channel111ch IEEE802.11g Frequency : 2412MHz~2462MHz Transmission systemOFDM Transmission speed 6M/12M/18M/36M/48M/54M Automatic detection Channel111ch IEEE802.11n(HT20) IEEE802.11n(HT20) Frequency : 2412MHz~2462MHz Transmission systemOFDM Transmission systemOFDM Transmission speed MCS0^MCS7 Automatic detection Channel:1-11ch
4/5 2. System Requirements (for the install) PF-SDMGN Users Manual A Personal computer or the embedded architecture that have SDIO V2.0 32 MB memory or greater(Recommend) 300 MHz processor or higher(Recommend) 3. Setup
(One of the methods) It uses Driver and a utility of Atheros Communications. Atheros client utility It completes installation according to setup Wizard 5/5