English WA100070XX Easy Setup Using WPS Feature SX-DS-3000WAN allows you to configure its wireless settings easily using a push switch if your wireless router supports WPS (Wi-Fi Protected Setup). This sheet explains how to configure wireless settings using the push switch.
! NOTE To perform the wireless configuration using WPS, your wireless router must support WPS. Please make sure that a wireless router supporting WPS is set up in your environment. While performing this configuration, please temporarily move SX-DS-3000WAN closer to your wireless router to make it easier for both devices to communicate. Depending on your wireless router, WPS may need to be enabled manually. For details, refer to the operation manual that came with your wireless router. If a security feature such as MAC Address filtering is enabled on your wireless router, disable it temporarily so that SX-DS-3000WAN can communicate with your wireless router. 1 Connect the AC adaptor to SX-DS-3000WAN and the AC plug to the power outlet. 2 Confirm that the Wireless LED(WLAN) on SX-DS-3000WAN blinks in Orange or turns to Green. 3 Press the WPS button on your wireless router. Confirm that your wireless router is ready for a wireless connection to be made. SX-DS-3000WAN Power Outlet SX-DS-3000WAN or AC Adaptor Searching for network Connected to existing network Wireless Router WPS
- It is not necessary to connect a network cable to SX-DS-3000WAN.
- If the Wireless LED does not blink in Orange or turn to Green, reset SX-DS-3000WAN to factory defaults and start from step 1 again. For how to reset SX-DS-3000WAN to its factory defaults, refer to the Users Manual or Setup Guide.
- The name, position and shape of the WPS button will differ depending on your wireless router. For details, refer to the operation manual that came with your wireless router.
- Please use only one wireless router. If two or more routers are waiting for wireless connections, SX-DS-3000WAN will not be able to connect properly. 4 Press and hold the push switch on SX-DS-3000WAN. When the Wireless LED blinks in Green, release the push switch. 5 SX-DS-3000WAN will start to communicate with your wireless router. The Wireless LED's lighting pattern will show you if the wireless configuration succeeded or failed. SX-DS-3000WAN Push Switch or SX-DS-3000WAN Success Fail
- Within 3-10 sec after pressing and holding down the push switch, the Wireless LED will blink in Green.
- It may take a while to complete the wireless configuration depending on your environment (up to 2 min). When successful, the Wireless LED will turn to Green. In this case, wireless configuration is complete.
- Power off SX-DS-3000WAN, move it to where you wish to use it and then power it on again.
- Connect the USB device(s) that you wish to use over the network to SX-DS-3000WAN.
- To install the software applications onto your computer, click Computer Configuration from the menu screen. For details, refer to the Users Manual.
- It is not necessary to install the applications if you plan to use printers with the standard Windows printing feature. When wireless configuration has failed, the Wireless LED will blink in Red. Read the instructions on this sheet and start from step 3 again. August, 2011 User Registration SX-DS-3000WAN Please complete the user registration after you nish the setup. It is required to provide you better technical supports and services. User Registration Website http://www.silex.jp/register/
For the user registration, a Serial Number is required. The Serial Number is a last 6-digit number of the Ethernet Address(12-digit number) which can be found on the bottom of the unit. Example: If the Ethernet Address is "00:80:92:00:11:22", the Serial Number will be "001122". English W A 0 6 1 7 0 X X Before You Begin About conguration methods Following 3 conguration methods are supported. Thank you very much for purchasing our wireless USB Device Server
"SX-DS-3000WAN". This Setup Guide provides information on how to congure and use SX-DS-3000WAN in your network environment. Please follow instructions on Step1- Step 4 to congure SX-DS-3000WAN. Before you begin, please carefully read the "Safety Instructions" and
"About Wireless Interference" in the online manual included in the CD-ROM to properly congure SX-DS-3000WAN. This Setup Guide explains how to congure SX-DS-3000WAN using a network cable. For other conguration methods, please refer to the online manual included in the CD-ROM.
- Conguration using a network cable (Recommended) By connecting SX-DS-3000WAN to your existing network using a network cable, you can congure the network settings from your computer. For this method, a network cable is required. Sample connection Network Cable Wireless Router SX-DS-3000WAN
- Conguration using a WPS feature of your wireless router If your wireless router supports WPS (Wi-Fi Protected Setup), the network conguration can be done automatically by pressing the wireless connection button on your wireless router and the push switch on SX-DS-3000WAN. For this conguration method, a wireless router supporting WPS is required.
- Conguration using a USB ash drive By saving the conguration information to a USB ash drive and connecting it to SX-DS-3000WAN, you can congure the network settings. To save the conguration information to the USB ash drive, please use the conguration utility contained in the CD-ROM. For this conguration method, a USB ash drive is required.
(De) Auf der CD-ROM befindet sich ein deutschsprachiges Setup-Handbuch im PDF-Format. Zum Anzeigen der PDF-Datei unter Windows bentigen Sie den Acrobat Reader.
(Fr) Un guide d'installation en franais au format PDF est inclus dans le CD-ROM. Acrobat Reader est ncessaire pour lire les fichiers PDF dans un environnement Windows.
(It) Una Guida alla configurazione in italiano inclusa nel CD-ROM come file PDF. Per visualizzare il file PDF in ambiente Windows necessario Acrobat Reader.
(Es) En el CD-ROM se incluye una Gua de instalacin en espaol como archivo PDF. Se necesita Acrobat Reader para ver el archivo PDF en un entorno Windows.
(Pt) Um Guia de Configurao em portugus fornecido no CD-ROM no formato de arquivo PDF. necessrio ter o Acrobat Reader para visualizar o arquivo PDF em um ambiente Windows. Package Contents Please check the following items are bundled with SX-DS-3000WAN:
SX-DS-3000WAN AC Adaptor Device Server Setup CD
(Including conguration software and online manual) Setup Guide (this document) SX Virtual Link Users Guide Warranty Booklet Rubber feet (4 psc) Step1 Necessary Wireless Setting Information To use SX-DS-3000WAN in your wireless network, SX-DS-3000WAN must have the same settings as your wireless router (Access Point). Please check the wireless settings of your router and write it down on the table below:
* The information below will be your own information that is used on your network and none of us are able to nd it from our side. For how to see each setting, please refer to the operating manual that came with your router or contact the manufacturer. Wireless Mode There are "Infrastructure" mode and "Ad hoc" mode. Select "Infrastructure" mode when you wish to connect to your network via a wireless router. Select "Ad hoc" mode when you wish to make a direct connection to your wireless computer without using a wireless router. When using this mode, set the same channel as your wireless computer. SSID The SSID is an ID that distinguishes a wireless LAN network from others. For wireless devices to communicate with each other on a wireless network, they must share the same SSID. (The SSID is also referred to as "ESSID".) Depending on your wireless router, it may have several SSIDs. If there are dierent SSIDs for a game machine and computer, use the one for the computer. SSID Conguration Memo Infrastructure / Ad hoc (ch. ) No Encryption Uses no encryption for wireless communication.
(In this case, you do not have to check any of your settings beforehand.) Network Authentication WEP
(Open / Shared)
WPA
WPA2 WEP If WEP encryption is used, wireless communication will be encrypted using the settings for "WEP Key 1-4" and
"Key Index". Set the same "WEP key Size(64bit/128bit)", "WEP Key"
and "Key Index" as your wireless router. WEP Key or Pre-Shared Key Encryption Mode
(Network Authentication) WPA / WPA2 Uses PSK for network authentication. The encryption key will be generated by communicating with the wireless router using a Pre-Shared key. WEP key setting is not used for this mode. Set the same "Pre-Shared key" and "Encryption Mode"(TKIP/AES) as your wireless router. The Pre-Shared key is also referred to as
"Network Key" or "Password". WEP key Size and Key Index Encryption Mode or Step2 Getting Started Connect SX-DS-3000WAN to your network using a network cable. 1 Connect SX-DS-3000WAN to your wireless router using a network cable. 2 Connect the AC adaptor to SX-DS-3000WAN and the AC plug to the power outlet. 3 Conrm that both POWER LED and LAN LED turn on. Wireless Router SX-DS-3000WAN Power Outlet POWER LED LAN LED SX-DS-3000WAN Parts and Fucntions
(4)
(6)
(2)(3)
(1)
(8) Network Cable AC Adaptor and SX-DS-3000WAN ON ON If POWER LED is OFF The AC adaptor is not plugged properly. Start from Step2-2 again. If LAN LED turns to Green or Orange Succsessfully connected to your network. Go on to Step 3. If LAN LED is OFF The network cable is not plugged properly. Start from Step2-1 again. If the network cable is plugged properly, SX-DS-3000WAN may contain icorrect network settings. In such a case, reset SX-DS-3000WAN to factory defaults and start from Step2-1 again. For details on how to reset SX-DS-3000WAN to factory defaults, refer to Factory Default Conguration.
(5)
(7) Factory Default Conguration
(1) Power Connector
(2) Network Port
(3) Push Switch
(4) Wireless LED
(5) LAN LED
(6) STATUS LED
(7) POWER LED
(8) USB Port
(9) Ethernet Address
(10) Serial Number E/A : 008092XXXXXX S/N : YYYYYYYYY
(9)
(10) If SX-DS-3000WAN has been used in other network or you wish to start conguration from factory defaults again, follow the instructions below. Remove the AC plug from the power outlet. 1 2 Press and hold down the push switch on SX-DS-3000WAN while inserting the AC plug back into the power outlet. Keep holding a while and release the push switch when LAN LED turns to Red. Power Outlet Push Switch SX-DS-3000WAN Power Outlet Keep holding down the push switch Push Switch SX-DS-3000WAN LAN LED ON Step3 Setup SX-DS-3000WAN Congure SX-DS-3000WAN using the conguration software included in the Device Server Setup CD. The conguration can be done from Windows or Macintosh computers.
<<< Windows environment >>>
Click Device Server Conguration. 2 3 Click Congure using the setup utility
(Recommended). 4 Click Yes. Check the notice information and click Next. 5 6 Read the software license agreement and click Yes. 1 Insert the Device Server Setup CD into your computer.
* If the menu screen does not appear automatically, open My Computer, select the CD-ROM drive and execute Autorun.exe.
* In Windows 7 (or Windows Vista), the User Account Control screen is displayed. Click Yes.
(Click Continue in Windows Vista). Select SX-DS-3000WAN and click Next. 7 8 Select Get IP Address Automatically and click Next. 9 Select the wireless network that you wish to connect to from a list , enter the network key and click Next. Check the settings and click Execute. 10 Click Yes and click Finish. 11
* If SX-DS-3000WAN is not displayed in a list,,,
- Check the network setting on your computer (IP address setting) is properly congured.
- Please temporarily disable the security software
(e.g. "Virus Buster" of Trend Micro, Inc.) or the
rewall function of Windows XP.
* If you wish to assign the IP address manually, click Assign IP Address and enter the IP address, subnet mask and default gateway.
* If the window does not have the option, Get IP Address Automatically, it is unable to obtain the IP address from DHCP server. In such a case, the sample address created with your computer's setting will be displayed. Please enter the IP address manually.
* Use the wireless setting information that you have checked at Step 1. Select the SSID of the wireless network that you to connect to and enter the network key. If the wireless network that you wish to connect to is not shown on a list, click Detailed Cong button and congure each setting in the window displayed.
* If you plan to use SX-DS-3000WAN on a wired network using a network cable, check Skip wireless conguration and click Next.
* The information diplayed here will dier depending on how you have congured. Before clicking Finish, follow the instructions on Step 4 to take eect of the conguration you made. After completing Step 4, click Finish and go on to install the USB device connection utility, "SX Virtual Link".
<<< Macintosh environment >>>
2 Double click the CD-ROM icon ( ) and then double click DSSetup ( ). 3 Click Device Server Conguration. 4 Click Congure using the setup utility
(Recommended). 5 Check the notice information and click Next. 6 Read the software license agreement and click Yes. 1 Insert the Device Server Setup CD into your computer. 7 Select SX-DS-3000WAN and click Next. 8 Select Get IP Address Automatically and click Next. 9 Select the wireless network that you wish to connect to from a list, enter the network key and click Next. Check the settings and click Execute. 10 Click Yes and click Finish. 11
* If SX-DS-3000WAN is not displayed in a list,,,
- Check the network setting on your computer
(IP address setting) is properly congured.
* If you wish to assign the IP address manually, click Assign IP Address and enter the IP address, subnet mask and default gateway.
* If the window does not have the option, Get IP Address Automatically, it is unable to obtain the IP address from DHCP server. In such a case, the sample address created with your computer's setting will be displayed. Please enter the IP address manually.
* Use the wireless setting information that you have checked at Step 1. Select the SSID of the wireless network that you with to connect to and enter the network key. If the wireless network that you wish to connect to is not shown on a list, click Detailed Cong button and congure each setting in the window displayed.
* If you plan to use SX-DS-3000WAN on a wired network using a network cable, check Skip wireless conguration and click Next.
* The information diplayed here will dier depending on how you have congured. Before clicking Finish, follow the instructions on Step 4 to take eect of the conguration you made. After completing Step 4, click Finish and go on to install the USB device connection utility, "SX Virtual Link". Step4 Enabling the New Settings Restart SX-DS-3000WAN to take eect of the new settings. 1 Remove the AC plug from the power outlet and then network cable from SX-DS-3000WAN. Power Outlet SX-DS-3000WAN 2 Connect the USB device that you wish to use over the network to SX-DS-3000WAN using a USB cable and then insert the AC plug of SX-DS-3000WAN to the power outlet. 3 SX-DS-3000WAN Power Outlet Conrm that the Wireless LED turns on. Wireless LED SX-DS-3000WAN ON Network Cable
* If you plan to use SX-DS-3000WAN on a wired network, it is not necessary to unplug the network cable. USB Devices If Wireless LED turns to Green Successfully connected to the wireless network. The setup is complete now. If Wireless LED blinks in Orange Searching for a wireless network. Please wait until a wireless connection is made. When not connected within 2-3 min, the SX-DS-3000WAN's wiress settings may not have been congured properly. Go back to Step 1 and check the wireless setting information once again. If Wireless LED is OFF The network cable is plugged. When you plan to use SX-DS-3000WAN in a wireless network, follow the instructions from Step 4-1 again. When you plan to use SX-DS-3000WAN in a wired network, check the LAN LED's lighting pattern. If the LAN LED turns to Green or Orange, SX-DS-3000WAN has been connected to a wired network. The setup is complete now. 4 Go on to install the USB device connection utility, SX Virtual Link. Please refer to the "SX Virtual Link User's Guide". FederalCommunicationCommissionInterferenceStatement ThisequipmenthasbeentestedandfoundtocomplywiththelimitsforaClassBdigitaldevice,pursuanttoPart15oftheFCCRules. Theselimitsaredesignedtoprovide reasonableprotectionagainstharmfulinterferenceinaresidentialinstallation. Thisequipmentgenerates,usesandcanradiateradiofrequencyenergyand,ifnotinstalled andusedinaccordancewiththeinstructions,maycauseharmfulinterferencetoradiocommunications. However,thereisnoguaranteethatinterferencewillnotoccurin aparticularinstallation. Ifthisequipmentdoescauseharmfulinterferencetoradioortelevisionreception,whichcanbedeterminedbyturningtheequipmentoffandon, theuserisencouragedtotrytocorrecttheinterferencebyoneormoreofthefollowingmeasures:
Reorientorrelocatethereceivingantenna. Increasetheseparationbetweentheequipmentandreceiver. Connecttheequipmentintoanoutletonacircuitdifferentfromthattowhichthereceiverisconnected. Consultthedealeroranexperiencedradio/TVtechnicianforhelp. ThisdevicecomplieswithPart15oftheFCCRules.Operationissubjecttothefollowingtwoconditions:(1)Thisdevicemaynotcauseharmfulinterference,and(2)this devicemustacceptanyinterferencereceived,includinginterferencethatmaycauseundesiredoperation. Thisdeviceisrestrictedtoindoorusewhenoperatedinthe5.15to5.25GHzfrequencyrange. This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. CanadaRequest ThisdevicecomplieswithIndustryCanadalicenceexemptRSSstandard(s).Operationissubjecttothefollowingtwoconditions:(1)thisdevicemaynotcauseinterference, and(2)thisdevicemustacceptanyinterference,includinginterferencethatmaycauseundesiredoperationofthedevice. Thedevicefortheband51505250MHzisonlyforindoorusagetoreducepotentialforharmfulinterferencetocochannelmobilesatellitesystems;
ThisClassBdigitalapparatuscomplieswithCanadianICES003. CetappareilnumeriquedelaclasseBestconformealanormeNMB003duCanada. This equipment complies with IC RSS-102 radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance20cmbetweentheradiator&yourbody.