Wireless E84 Digital Communication DeviceWDCD-3310User Manual WDCD-3310 is a device that E84 interlock communication by wireless communication during FOUP transfer between the OHTOverhead Hoist Transferand semiconductor manufacturing equipment. The WDCD-3310 is equipped on the semicunductor manufacturing equipment. Antenna connector micro USB Push Switch 10pin connector DIP Switch 5pin connector 3pin connector 12pin connector W-E84 LED STATUS LED POWER LED Parts and Functions POWER LED STATUS LED Green light on
: Power On Green light flashing
: Program changing Orange light on
: Initializing process Red light on Green light on Orange light on Red light on
: Hardware error
: Power On
: Setting various parameters of wireless E84 device via tool
: Wireless E84 device parameter setting error via tool Green light flashing
: Communicating in the 2.4 GHz band Orange light on
: Power On(5.8GHz) Orange light flashing
: Communicating in the 5.8 GHz band Red light on
: An error occurred in communication with the wireless E84 unit W-E84 LED Green light on
: Power On(2.4GHz) CPU internal ROM writing (only used in the factory) Connect to semicondutor manufacturing equipment Connect to semicondutor manufacturing equipment Debug port Debug port Antenna connector Connect the antenna Push Switch Used to initialization settings 3pin connector 5pin connector 10pin connector 12pin connector Micro USB Setup 1.Use a dedicated cable to connect the 10-pin & 12-pin connector to semiconductor manufacturing equipment. 2.Powered by semiconductor manufacturing equipment and controls WDCD-3310. Basic configration Wireless Frequency Band Wireless Channel Wireless Channel Width 1MHz Channel Power setting ISM2.4GHz,5.8GHz Ch3~Ch80(2.4GHz) Ch2~Ch100(5.8GHz)
-20dBm~0dBm(2.4GHz)
-20dBm~+2dBm(5.8GHz) 10,20,30,40,50ms 100~60000ms 100~5000ms
-80~-24dBmNo threshold Channel Period Receive timeout Commnication timeout Pairing threshold level Specification Operating environment Power supply Wireless I/F Push Switch LED Strorage environment Temperature
-10~+50 Temperature 0~+40 Humidity 20~80%RH(Non condensing) Humidity DC24V 20~90%RH(Non condensing) short-range wireless(2.4GHz/5.8GHz) initializaition swtich 1 POWER LED STATUS LED W-E84 LED Green/Red/Orange Green/Red/Orange Green/Red/Orange Supplier's Declaration of Conformity 47 CFR 2.1077 Compliance Information Unique Identifier: WDCD-3310 Responsible Party U.S. Contact Information Responsible Party Name: silex technology America, Inc. Responsible Party Address: East Sandpointe, #245 Santa Ana, CA 92707 Phone: 657-218-5199 FCC Compliance Statement This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference undesired operation. FCC CAUTION Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Note:
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. Compliance with FCC requirement 15.407 Data transmission is always initiated by software, which is the passed down through the MAC, through the digital and analog baseband, and finally to the RF chip. Several special packets are initiated by the MAC. These are the only ways the digital baseband portion will turn on the RF transmitter, which it then turns off at the end of the and can radiate radio frequency energy and, if not installed and used in accordance with the instruction packet. Therefore, the transmitter will be on only while one of the aforementioned packets is being transmitted. In other words, this device automatically discontinue transmission in case of either absence of information to transmit or operational failure. Frequency Tolerance: 60 ppm This transmitter must not be co-located or operated in conjunction with any other antenna or transmitter. This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment and meets the FCC radio frequency (RF) Exposure Guidelines as this equipment has very low levels of RF energy.