FCC ID: 2AP2L-SR74FA02 Solar LED Light

SOLAR LED AREA WALL LIGHT WITH MOTION SENSOR ITEM: SR74FA02C-08 INSTRUCTIONS FOR FIRST TIME USE: SOLAR LIGHT NEEDS TO CHARGE IN FULL SUNLIGHT FOR 8 -12 HOURS WITH THE SWITCH IN THE ON POSITION TO FULLY CHARGE THE BATTERY. The intelligent solar LED motion activated light measures the available battery power capacity and adjusts the light's performance to maximize runtime. Tools Required INSTALLATION Hardware Included Pencil Phillips-head Screwdriver Electric drill drill bit size:

7.5mm (3/10 in.)

(A) Screw X 4

(B) Wall Anchor X 4 Parts

(C) Light Fixture X 2

(D) Mounting Plate X 2 2.36in. (60mm) x x 1 Marking the location Mark the location where you want to mount the light xture (Part C). Measure the width of two holes on the back of the mounting plate

(Part D) and mark holes for the 2 screws (Part A) on the surface. The distance between the two holes is 2.36in. (60mm). Drill two holes. 2 Mounting the light fixture Insert the wall anchors (Part B) so they are ush with the surface. Secure the mounting plate (Part D) in place with the screws (Part A). Mount the light on the mounting plate (Part D) by aligning the holes on the back of the light to the knobs on the front of the mounting plate. Align, insert, and slide down to lock in place. B A D C NOTE: Light xture will stay on 30 seconds when triggered by motion and revert back to standby mode of 20 lumens until motion is detected. For best performance, mount the light a minimun 6 feet (1.8 m) above the ground. Detection range is 26 feet (8 m), detection angle is 120. Light xture uses radio frequency technology to link, and should not be greater than 98 feet (30 m) between the neighboring/adjacent lights. When one light is triggered by motion both lights will activate. The package includes 2 lights. These 2 lights are factory linked, and can not be linked with more of the same type light or any other lights. REPLACING THE BATTERY TROUBLE SHOOTING If light doesnt turn on, check the battery to ensure that it is making secure contact with the terminals. If this doesnt work, replace with a new battery. Slide the power switch to the "OFF" position. Use a Phillips head screwdriver to remove the 4 screws holding the battery cover in place. Replace old battery with a new 3.7V, 2000 mAh lithium (18650) rechargeable battery. Replace the battery cover by aligning it properly and replacing the 4 screws removed earlier. Slide the power switch to the ON position. For optimal performance, allow light fixture to charge in full sunlight for 8-12 hours, to fully charge the battery. Screws Battery Cover Power Switch Battery E SOLAR LED AREA WALL LIGHT WITH MOTION SENSOR ITEM: SR74FA02C-08 FCC WARNING Warning: Changes or modications to this unit not expressly approved by the party responsible for compliance could void the user authority to operate the equipment. Notes: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency enerqy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no quarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio / TV technician for help. RF EXPOSURE: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance of 20 cm between the radiator and your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. WARNING: Do not dispose of lithium batteries in municipal waste stream or by re as batteries may explode. Do not open, short circuit, or destroy batteries. Dispose of batteries in accordance with Local, State, and Federal regulations. Do not mix old and new batteries. Do not mix alkaline, standard (carbon-zinc), or rechargeable (nickel cadmium, nickel metal hydride or lithium ion) batteries . For additional help and information regarding installation, contact customer service at 1-844-551-0680, 8am-5pm, CST Monday Friday customerservice@qx-usa.com and Westinghouse are trademarks of Westinghouse Electric Corporation. Used under license by Sky Rich Star Limited. All Rights Reserved. 2/2E LUZ DE PARED DE REA LED SOLAR CON SENSOR DE MOVIMIENTO ITEM: SR74FA02C-08 INSTRUCCIONES PARA EL PRIMER USO: LA LUZ SOLAR NECESITA CARGARSE BAJO LUZ SOLAR DIRECTA POR UN PERIODO DE ENTRE 8 Y 12 HORAS CON EL INTERRUPTOR EN LA POSICIN "ON" (PRENDIDO) PARA CARGAR COMPLETAMENTE LA BATERA. La luz LED solar inteligente activada por movimiento mide la capacidad de energa disponible de la batera y ajusta el rendimiento de la luz para maximizar el tiempo de ejecucin. Herramientas Necesarias INSTALACIN Herrajes Incluidos

(A) Tornillo X 4

(B) Anclajes de pared X 4 Taladro elctrico tamao de la broca de taladro: 7.5 mm (3/10 plg) Partes

(C) Lmpara X 2

(D) Base X 2 2.36in. (60mm) x x Lpiz Cabeza de Phillips Destornillador 1 Cmo marcar el lugar de montaje Marque el lugar en el que quiere montar el artefacto de iluminacin

(Parte C). Mide el ancho de los dos oricios que estn en la parte posterior de la montaje placa (Parte D) y marque alinearlos con 2 tornillos

(Parte A) La distancia entre los oricios es de 2.36in. (60mm). Taladre dos oricios. 2 Cmo montar la lmpara Inserta los anclajes de pared (Parte B) de manera que queden al ras de la supercie. Fije la placa de montaje (Parte D) en su sitio con los tornillos (Parte A). Monte la luz en la placa de montaje (Parte D) alineando los oricios de la parte posterior de la luz con la perillas en la parte frontal de la placa de montaje. Alinee, inserte y deslice hacia abajo para bloquearlo en su lugar. NOTA: Cuando la luz se active con un movimiento, permanecer encendida durante 30 segundos, volver al modo de espera de 20 lmenes hasta que se detecte movimiento. Para un mejor funcionamiento, instale el accesorio aproximadamente la luz un mnimo de 6 pies (1.8 m) por encima del suelo. El rango de deteccin es de 26 pies (unos 8 metros), el ngulo de deteccin es de 120 . La luz usos la tecnologa de radiofrecuencia para la vinculacin, por lo cual no debe haber ms de 98 pies (unos 30 metros) entre luces adyacentes. Cuando una luz se activa por movimiento, ambas luces se activarn. El paquete incluye 2 luces. Estas 2 luces estn vinculadas de fbrica y no se pueden vincular con ms del mismo tipo de luz o cualquier otra luz. C D B A SOLUCIN DE PROBLEMAS Si no se enciende la luz, revise la batera para asegurarse que estn haciendo contacto rmemente con las terminales. Si esto no funciona, reemplace la batera con una nueva. CAMBIANDO LA BATERA Deslice el interruptor a su posicin de "OFF" (apagado). Use un destornillador Phillips (estrella) para retirar los 4 tornillos que sostienen la tapa de las bateras. Reemplace la batera antigua con una nueva batera recargable de litio (18650) de 3.7V, 2000 mAh. Vuelva a colocar la tapa de las bateras alinendola adecuadamente y vuelva a colocar los 4 tornillos que retir anteriormente. Deslice el interruptor a su posicin de "ON" (prendido). Para un rendimiento ptimo, permita que la lmpara se c argue a plena luz del sol durante 8-12 horas, para cargar completamente la batera. Tornillos Tapa de las batera Interruptor de encendido Batera S LUZ DE PARED DE REA LED SOLAR CON SENSOR DE MOVIMIENTO ITEM: SR74FA02C-08 ADVERTENCIA DE LA FCC Advertencia: los cambios o modicaciones a esta unidad no aprobados expresamente por la parte responsable del cumplimiento pueden anular la autorizacin del usuario para operar el equipo. Notas: Este equipo ha sido probado y cumple con los lmites para un dispositivo digital de Clase B, de acuerdo con la Parte 15 de las Reglas de la FCC. Estos limits estn diseados para la proteccin contra interferencias dainas en una instalacin residencial. Este equipo genera, utiliza y puede irradiar energa de radiofrecuencia y, si no se instala y utiliza de acuerdo con las instrucciones, puede causar interferencia perjudicial a la comunicaciones de radio. Sin embargo, no hay garanta de que no se produzcan interferencias en una instalacin en particular. Si este equipo causa interferencia perjudiciales a la recepcin de radio o televisin, lo cual puede determinarse apagando y encendiendo el equipo, se recomienda al usuario que intente corregir la interferencia mediante una o ms de las siguientes medidas:

Reorientar o reubicar la antena receptora. Aumente la separacin entre el equipo y el receptor. Conecte el equipo a una toma de corriente en un circuito distinto al que est conectado el receptor. Consulte con el distribuidor o un tcnico de radio / TV con experiencia para obtener ayuda. EXPOSICIN A RF: Este equipo cumple con los lmites de FCC de exposicin a la radiacin establecidos para ambientes no controlados. Este equipo debe ser instalado y operado con una distancia mnima de 20 cm entre el radiador y su cuerpo. El transmisor no debe colocarse ni operarse junto con ningn otro transmisor o antena. CUIDADO: No deseche las bateras de litio en la corriente de desechos municipales o por el fuego, ya que las bateras pueden explotar. No abra, provoque cortocircuitos ni mutile las bateras. Deseche las bateras de acuerdo con los reglamentos locales, estatales y federales. No mezcle las bateras viejas con las nuevas. No mezcle las bateras alcalinas, estndar (carbono-zinc) ni recargables (nquel-cadmio, nquel e hidruro metlico o ion litio). Para obtener ayuda e informacin adicional acerca de la instalacin, comunquese con servicio a clientes al 1-844-551-0680 de lunes a viernes de 8:00 A.M. a 5:00 P.M. en el horario del centro de EE. UU. customerservice@qx-usa.com and Westinghouse are trademarks of Westinghouse Electric Corporation. Used under license by Sky Rich Star Limited. All Rights Reserved. 2/2S

30 mm 45mm Model No.: SR74FA02C-08 FCC ID: 2AP2L-SR74FA02 This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Agent Authorization Company: SKY RICH STAR LIMITED Address: Unit E, 10/F, Worldwide Centre, 123 Tung Chau Street, Tai Kok Tsui Kowloon, Hong Kong, China Product Name: Solar LED Light Model Number(s): SR74FA02C-08, SR74FA02*-##Where "#" is used to denote numbers or blank for commercial purpose; Where * is used to denote letters or blank for commercial purpose.) Product Description: Solar LED Light We authorize MiCOM Labs Inc., 575 Boulder Court, Pleasanton, California 94566, USA, to act on our behalf on all matters concerning the certification of above named equipment. We declare that MiCOM Labs Inc. is allowed to forward all information related to the approval and certification of equipment to the regulatory agencies as required and to discuss any issues concerning the approval application. Any and all acts carried out by MiCOM Labs on our behalf shall have the same effect as acts of our own. Date: 2022-04-07 Signature:

Name:

zhiquan li Title:

Manager Company: SKY RICH STAR LIMITED

Differences Declaration We company SKY RICH STAR LIMITED hereby To whom concern, declares:

The product models SR74FA02C-08, SR74FA02*-##Where "#" is used to denote numbers or blank for commercial purpose; Where * is used to denote letters or blank for commercial purpose.) are identical in the same PCB layout, interior structure and electrical circuits, The differences are appearance color and model name for commercial purpose. Authorized signature:

Date: 2022-04-12

SKY RICH STAR LIMITED Office of Engineering Technology Federal Communications Commission 7435 Oakland Mills Road Columbia, MD21046 Subject; Request for Confidentiality FCC ID: 2AP2L-SR74FA02 Date: 2022-04-07 To Whom It May Concern, Pursuant to the provisions of the Commissions rules Title 47 Sections 0.457 and 0.459, we are requesting the Commission to withhold the following attachment(s) as confidential documents from public disclosure indefinitely. These documents contain detailed system and equipment descriptions and are considered as proprietary information in operation of the equipment. The public disclosure of these documents might be harmful to our company and would give competitors an unfair advantage in the market. Schematic Diagram Block Diagram Operational Description Pursuant to Public Notice DA 04-1705 of the Commission' s policy, in order to comply with the marketing regulations in 47 CFT 2.803 and the importation rules in 47 CFR 2.1204, while ensuring that business sensitive information remains confidential until the actual marketing of newly authorized devices, we request Short Term Confidentiality of the following attachment(s);

External Photos Test Setup Photos Internal Photos User Manual For 45 days, pursuant to Public Notice DA 04-1705. OR For 180 days pursuanttoKDB 726920 D01. It is our understanding that all measurement test reports, FCC ID label format and correspondence during the certification review process cannot be granted as confidential documents and this information will be available for public review once the grant of equipment authorization is issued. Sincerely, Signature:

Name: zhiquan li Title: Manager