FCC ID: AK8M1502 Communication module

User Manual Since this module is not sold to general end users directly, there is no user manual of module. For the details about this module, please refer to the specification sheet of module. This module should be installed in the host device according to the interface specification

(installation procedure). This device complies with below part 15 of the FCC Rules. Part 15 Subpart C The modular transmitter is only FCC authorized for the specific rule parts (i.e., FCC transmitter rules) listed on the grant, and the host product manufacturer is responsible for compliance to any other FCC rules that apply to the host not covered by the modular transmitter grant of certification. transmitter installed. The final host product still requires Part 15 Subpart B compliance testing with the modular This module needs to be supplied a regulated voltage from host device. The following information must be indicated on the host device of this module;

[for FCC]

Contains Transmitter Module FCC ID: AK8M1502 This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that may cause undesired operation.

*If it is difficult to describe this statement on the host product due to the size, please describe in the User's manual.

[for ISED]

Contains IC: 409B-M1502 The following statements must be described on the user manual of the host device of this module;

[for FCC]

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that may cause undesired operation. FCC CAUTION Changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. This transmitter must not be co-located or operated in conjunction with any other antenna or transmitter. This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment and meets the FCC radio frequency (RF) Exposure Guidelines. This equipment should be installed and operated keeping the radiator at least 20cm or more away from persons body.

[for ISED]

This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canadas licence-exempt RSS(s). Operation is subject to the following two conditions:

1. This device may not cause interference. 2. This device must accept any interference, including interference that may cause undesired operation of the device. Lmetteur/rcepteur exempt de licence contenu dans le prsent appareil est conforme aux CNR dInnovation, Sciences et Dveloppement conomique Canada applicables aux appareils radio exempts de licence. Lexploitation est autorise aux deux conditions suivantes :

1. Lappareil ne doit pas produire de brouillage;

2. Lappareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible den compromettre le fonctionnement. This equipment complies with ISED radiation exposure limits set forth for an uncontrolled environment and meets RSS-102 of the ISED radio frequency (RF) Exposure rules. This equipment should be installed and operated keeping the radiator at least 20cm or more away from persons body. Cet quipement est conforme aux limites dexposition aux rayonnements nonces pour un environnement non contrl et respecte les rgles dexposition aux frquences radiolectriques (RF) CNR-102 de lISDE. Cet quipement doit tre install et utilis en gardant une distance de 20 cm ou plus entre le radiateur et le corps humain. This radio transmitter (409B-M1502) has been approved by Innovation, Science and Economic Development Canada to operate with the antenna types listed below, with the maximum permissible gain indicated. Antenna types not included in this list that have a gain greater than the maximum gain indicated for any type listed are strictly prohibited for use with this device. Antenna type

/2 monopole antenna Gain 3 dBi Impedance 50 ohm Le prsent metteur radio (409B-M1502) a t approuv par Innovation, Sciences et Dveloppement conomique Canada pour fonctionner avec les types dantenne numrs ci-dessous et ayant un gain admissible maximal. Les types dantenne non inclus dans cette liste, et dont le gain est suprieur au gain maximal indiqu pour tout type figurant sur la liste, sont strictement interdits pour lexploitation de l metteur. Type dantenne

/2 antenne monople Gain 3 dBi limpdance 50 ohm

MARKING _C: M1502 D: E: FCC ID:AK8M1502__F: IC:409B-M1502 El) CBaRRA (Max 7XF) RES.

(TXFCMA SHO URSSARRTRE EI) BRUOvhES (Max 7 UF) eRETS. BORG! (Max l OXF) PETS. ESRUFBGRESSeRETS. (ER:MaxiTLF, FRiMax 1 5UFETS) do Lima SAAN tuanmoamainases imu 1 | Joo [ro 2h

v Yi Nee ee RS em ee Ne NC Ft INSTRUCTIONS >

PRODUCT NO. ( MAX 7 CHARACTERS ) IN SECTION C.

(FOR MORE THAN 7 CHARACTERS FOLLOW RULES FOR ABBREVIATIONS. }

2) LOT NO. ( MAX 7 CHARACTERS ) IN SECTION B. 3) PRODUCT ID( MAX 10 CHARACTERS ) IN SECTION D. 4) CERTIFICATE NO. IN SECTION E AND F.

(SECTION E:MAX_17 CHARACTERS, SECTION F:MAX 15 CHARACTERS) 5) THE RIGHT UPPER MICRO QR CODE SHOWS PRODUCT ID OF SECTION D.

(THE FIGURE SHOWS PRINT EXAMPLE)

SONY Sony Semiconductor Solutions Corporation 4-14-4 Asahi-cho, Atsugi-shi, Kanagawa, 243-0014 Japan Letter of Authorization Date: March 23, 2020 UL Japan, Inc. 4383-326 Asama-cho, Ise-shi, Mie 516-0021 Japan FCCID :AK8M1502 Applicant: Sony Corporation To whom it may concern:

Please be advised we authorize Akiko Nishimura of Consumer Technology Division, UL Japan, Inc. to act on our behalf, until otherwise notified, for applications submitted for Federal Communication Commission Radio equipment applications submitted to UL Japan, Inc. We certify that we are not subject to denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse ACT of 1988, U.S.C. 862. Further, no party, as defined in 47 CFR 1.2002(b), to the application is subject to denial of federal benefits, that includes FCC benefits. The application for the subject equipment has not been submitted to another TCB for certification. Thank you for your attention to this matter. Sincerely, Sony Semiconductor Solutions Corporation

SONY Sony Semiconductor Solutions Corporation 4-14-4 Asahi-cho, Atsugi-shi, Kanagawa, 243-0014 Japan Declaration Letter of professional installation Date: March 23, 2020 UL Japan, Inc. 4383-326 Asama-cho, Ise-shi, Mie 516-0021 Japan FCCID :AK8M1502 Applicant: Sony Corporation To whom it may concern:

Please be advised M1502, model: M1502 is Communication module for the ELTRES LPWA wireless standard established by ETSI only and mounted inside of the end product by us professionally. As regards the detailed conditions for installation, please refer to Theory of Operation-Interface specification. Thank you for your attention to this matter. Sincerely, ayuki Nagai Sony Semiconductor Solutions Corporation

Sony Semiconductor Solutions Corporation 4-14-4 Asahi-cho, Atsugi-shi, Kanagawa, 243-0014 Japan Request for Modular Transmitter Approval May 14, 2020 FCC ID : AK8M1502 Applicant : Sony Corporation This transmitter, model: M1502 is designed by us. It complies with the modular transmitters basic requirements (Item 1 to 8) in FCC Part 15 Subpart C Section 15.212 as indicated below:

Modular Approval Checklist:

Modular approval requirement

(1) Have its own RF shielding.

(2) Have buffered modulation/data inputs.

(3) Have its own power supply regulation. Yes No Please refer to Block Diagram. This EUT has the power supply regulator, however one of the input voltages to RF part doesnt go through the regulator. The stable voltage will be supplied by the end product, which will be required to have a power supply regulator. the antenna and transmission system

(4) Comply with requirements of 15.203, 15.204(b) and 15.204(c).

(5) Tested in a stand-alone configuration. Unless the transmitter module will be battery powered, it must comply with the AC line conducted requirements found in FCC 15.207. AC or DC power lines and data input/output lines connected to the module must not contain ferrites, unless they will be marketed with the module. The length of these lines shall be the length typical of actual use or, if that length is unknown, at least 10 centimeters to insure that there is no coupling between the case of the module and supporting equipment. Any accessories, peripherals, or support equipment connected to the module during testing shall be unmodified and commercially available.

(6) Equipped with either a permanently affixed label or must be capable of electronically displaying its FCC ID. If the FCC ID is not visible when the module is installed inside another device, then the outside of the device into which the module is installed must also display a label referring to the enclosed module.

(7) Comply with any specific rules or operating requirements that ordinarily apply to a complete transmitter and the manufacturer must provide adequate instructions along with the module to explain any such requirements.

(8) Comply with any applicable RF exposure requirements in its final configuration: The modular transmitter complies with FCC radiation exposure requirement. Takayuki Nagai Sony Semiconductor Solutions Corporation

SONY Sony Semiconductor Solutions Corporation 4-14-4 Asahi-cho, Atsugi-shi, Kanagawa, 243-0014 Japan Request for Confidentiality Date: March 23, 2020 UL Japan, Inc. 4383-326 Asama-cho, Ise-shi, Mie 516-0021 Japan FCCID :AK8M1502 Applicant: Sony Corporation To whom it may concern:

Please be advised that the following information is to be held confidential based on the FCC rules 0.457 and 0.459:

Block Diagram Theory of Operation Schematics The application contains technical information which we deem to be trade secrets and proprietary. If made public, the information might be used to the disadvantage of the applicant in the market place. Thank you for your attention to this matter. Sincerely, ony Semiconductor Solutions Corporation

SONY Sony Corporation 1-7-1 Konan, Minato-ku Tokyo 108-0075 Japan TEL: +81-3-6748-2111 FAX: +81-50-3809-1350 Special Power of Attorney To whom it may concern:

1, Ryo Takata of Sony Corporation hereby appoint Takayuki Nagai of Sony Semiconductor Solutions Corporation to represent me to act on my behalf to do any and all of the following:

Sign the following documents on my behalf and apply to FCC for the products

- Letter of agency and anti-drug

- Confidentiality cover letters

- Any other application document that requires a signature by grantee. The rights, powers and authority in fact to exercise any and all of the rights and powers herein granted shall commence and be in full force and effective from March 23, 2020 unless specifically extended or terminated by either party. Date: March 23, 2020 Place: Japan Ryo Takata Sony Corporation