FCC ID: O9YFLF2PL GPS tracker

Flex2PL User Manual Revision 1.0 Index NALA USER MANUAL................................................................................................................................ 1 1 INTRODUCTION....................................................................................................................................... 2 2 PHYSICAL AND ELECTRICAL SPECIFICATIONS...........................................................................2 3 LED INDICATORS.....................................................................................................................................2 4 TRACKING BEHAVIOR SUMMARY.................................................................................................... 2 5.RF EXPOSURE INFORMATION AND STATEMENT.........................................................................2 1 1 Introduction it is a remote start and security tracking device that uses a GPS satellite receiver to determine location information and an LTE transceiver to communicate information to and from a land based server. This document outlines the operation and configuration of the Nalaproduct line using the supplied tracking application. This document is user manual for Nala. 2 Physical and Electrical Specifications There are 3 indicator LEDs on the device, which are used to indicate the status of cellular communications and GPS, and to indicate when messages are created and transmitted. Input Voltage: 10-30VDC Power consumption:

- Active mode: 120mA @12VDC

- Low power mode: 15mA @ 12VDC Operating temperature: -30 to 70 Storage temperature: -40 to 85 3 LED Indicators The orange LED indicates communications status:

The device enters a sleep low-power state The RED LED indicates GPS status:

Off indicates modem is off Off indicates GPS is off Indicates network status The green LED indicates GPS status:

The device starts normally Instruct to turn on the GPS, and the GPS works normally. Implies that GPS has been successfully located 4 Tracking Behavior Summary Nala applications address the needs of typical vehicle and asset tracking. Variations in functional behavior for specific applications is controlled via parameters in the settings file. 1) Power State Reporting The Nala can be configured to report power up and rebooting behavior in a variety of ways depending on what is desired. Cold Boot, Warm Boot, and first GPS Acquisition are reported if so configured following Power Up events, power cycling, commanded reboots, 2 and configured periodic reboots. In addition, there is an option to report a Stop event following a reboot of a non-moving device to address some customer needs to ensure that the corner case of a reboot occurring at the end of a trip doesnt result in an error in trip or idle reporting by the server. If the device is equipped with a backup battery, then it will also report Power Disconnected and Power Connected events when primary power is removed and restored. 2) Moving State A device enters Moving state either due to detection of a hardwired Ignition signal, an increase in the supply voltage, detection of movement by the GPS, or an Absolute G detection. While in Moving state, the device reports periodically as configured. Both primary Moving interval reports with full data, and minor intervals (with only latitude, longitude, speed, and time) for data compression can be reported while in Moving state. 3) Sleeping State A device enters Sleeping state from Stopped state when all of vibration, GPS movement, and primary voltage are quiescent for a sufficient duration. The qualifying duration of quiescence, and the degree of sleep encountered, are controlled by parameters in the Settings file. 4) Heartbeat Reporting 5.RF Exposure Information and Statement The device reports a Heartbeat message at an interval specified regardless of state. If the device is sleeping when the Heartbeat timer expires, it will wake up and generate the Heartbeat message. Whether the device attempts a GPS fix for each Heartbeat message can be specified. This equipment complies with FCC and IC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance of 20 cm between the radiator and your body. This transmitter must not be co-

located or operating in conjunction with any other antenna or transmitter. This device complies with part 15 of the FCC rules and RSS-247 of Industry Canada. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. 3 Le prsent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorise aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible d'en compromettre le fonctionnement. This Class B digital apparatus complies with Canadian ICES-003. Cet appareil numrique de la classe B est conforme la norme NMB-003 du Canada. NOTE: The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment. Such modifications could void the users authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

-Connect the equipment into an outlet on a circuit different from that to which the receiver is measures:

connected.

-Consult the dealer or an experienced radio/TV technician for help

- This device and its antenna(s) must not be co-located or operating in conjunction with any other antenna or transmitter. 4

SN: AS220360000007 IMEI: 866298030000007 M/N: Flex2PL-SL-L-A FCC ID: O9YFLF2PL IC: 22952-FLF2PL P18150 H/W : 2.0.0 Designed in California Made in China 352165050019160 352165050019160 Flex2PL-SL-L-A SN: AS220360000007 IMEI: 866298030000007 M/N: Flex2PL-SL-L-A FCC ID: O9YFLF2PL IC: 22952-FLF2PL P18150 H/W : 2.0.0 Designed in California Made in China Flex2PL-SP-L-A SN: AS220360000007 352165050019160 IMEI: 866298030000007 352165050019160 M/N: Flex2PL-SP-L-A FCC ID: O9YFLF2PL IC: 22952-FLF2PL P18150 H/W : 2.0.0 Designed in California Made in China Flex2PL-CN-L-A SN: AS220360000007 352165050019160 IMEI: 866298030000007 352165050019160 M/N: Flex2PL-CN-L-A FCC ID: O9YFLF2PL IC: 22952-FLF2PL P18150 H/W : 2.0.0 Designed in California Made in China I S D E U P T H S I I S D E U P T H S I I S D E U P T H S I I S D E U P T H S I I S D E U P T H S I Carrier Code :2 for AT&T 7 for Verizon Factory Code : S = Starnet Q = Qiao X ing Version #

Update when there is any upgrade on H/W Model #

Assigned by ATEL 352165050019160 352165050019160 Date code: YYWW Last 7 digits of IMEI SN: AS220360000007 IMEI: 866298030000007 M/N: Flex2PL-SL-L-A FCC ID: O9YFLF2PL IC: 22952-FLF2PL P18150 H/W : 2.0.0 Designed in California Made in China FCC / IC ID H/W = Hardware Version 352165050019160 Date Code

[P=Product + Year 18 + Week 15 + RMA Code 0]

352165050019160 IMEI#

Assigned by Vendor All Barcode is Code 128 Format

Spireon Inc Agent Authorization Company: Spireon Inc Address: 9724 Kingston Pike, Suite 800 Knoxville, TN37922 Product Name: GPS tracker Model Number(s): Flex2PL Product Description: GPS tracker We authorize MiCOM Labs Inc., 575 Boulder Court, Pleasanton, California 94566, USA, to act on our behalf on all matters concerning the certification of above named equipment. We declare that MiCOM Labs Inc. is allowed to forward all information related to the approval and certification of equipment to the regulatory agencies as required and to discuss any issues concerning the approval application. Any and all acts carried out by MiCOM Labs on our behalf shall have the same effect as acts of our own. Signature:

Date: 2021-01-20 Name:

Jason Penkethman Title:

Chief Product & Strategy Officer Company: Spireon Inc

Spireon Inc Date: 15 Jan, 2021 To:

Federal Communications Commission, Authorization & Evaluation Division, 7435 Oakland Mills Road, Columbia, MD 21046 To Whom It May Concern:

Spireon Inc, the undersigned, hereby authorizes Mr. Wu Xuewen from Shenzhen BALUN Technology Co., Ltd., to act on the behalf of the Spireon Inc. solely in matters relating to the application for an FCC equipment authorization for FCC ID: O9YFLF2PL including the signing of documents in connection with this Application. Necessary acts carried out by Shenzhen BALUN Technology Co., Ltd. in connection with the Application shall have the same effect as acts of Spireon Inc. Spireon Inc also hereby certify that no party to this application is subject to a denial of benefits, including FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. Section 862. Yours Sincerely, Print name: Jason Penkethman Title: Chief Product & Strategy Officer Spireon Inc

Spireon Inc Date: 15 Jan, 2021 To:

Federal Communications Commission, Authorization & Evaluation Division, 7435 Oakland Mills Road, Columbia, MD 21046 RE: Spireon Inc FCC ID: O9YFLF2PL FCC Certification Confidentiality Request Gentlemen:

Exhibit Type Block Diagram Schematics Operational Description Part list Tune-Up-Procedure File Name Block Diagram.pdf Schematics.pdf Operational Description.pdf BOM.pdf Tune up procedure.pdf Thank you for your attention to this matter. vours Sincerely, Print name: Jason Penkethman Title: Chief Product & Strategy Officer Spireon Inc This letter is to comply with 47 CFR 0.457 and 0.459 pertaining to confidentiality material. Spireon Inc requests that the following documents regarding this submission for FCC ID: O9YFLF2PL be kept Long-Term confidential:

Those documents ~ontain detailed system and equipment description and related information about the product which Spireon Inc. considers to be confidential proprietary, a custom design aod, otherwise, not releasable to the general public. Since this design is a basis form which future technological products will evolve, Spireon Inc considers this information would be of benefit to its competitors, and that the disclosure of the information in these documents would give competitors an unfair advantage in the market.