BWA19WI702 70 x 70 mm 80g
/
Product Diagram 1 3 2 7 8 5 6 9 4 11 10 12 13 1. Cradle Locking Side Arms 2. Fast Clamping Button / Wireless Charger 3. Cradle Release Bars 4. Charging Indicators 5. Stabilizing Nut 6. Micro USB Port 7. Ball Joint 8. Clamp Lock 9. Air Vent Blade Clamp 10. Car Charger / Indicator
(Green: Fast Charging; Blue: Standard Charging) 11. USB A Output: Quick Charge 3.6V-6.5V/3A,6.5V-9V/2A,9V-12V/1.5A
(Green) 12. USB A Output: 5V/2.4A (White) 13. Micro USB Cable TM WIRELESS CHARGING CAR MOUNT Model: BWA19WI702 Mounting & Using the Phone Holder Powering the Wireless Charger Loosen the stabilizing nut, insert the ball joint, and then tighten the nut to lock in place Squeeze the cradle release bars to open the locking side arms. Place your phone against the Fast Clamping Button to close the arms against your device. Green Chip: (Quick Charge, Recommended) White Chip:
(Charging at normal speed) Press down the clamp lock, insert the clamp onto your air vent blade, and release the lock to secure in place Note: Rotate the ball joint to t the clamp into horizontal or vertical blades. Rotate the ball joint to obtain your best viewing angle 1. Connect the micro USB cable into the charging port. 2. Insert the USB port into a car charger. The wireless charger LED indicator will turn on blue for 10 seconds indicating a successful connection. 57.7 - 87.7mm /
2.27 - 3.45 in Position your phone so that back-center aligns with Fast Clamping Button. The arms will automatically close against your device upon a slight push against the clamp trigger. Note:
Line up the center of phone with the charging coils to achieve ecient charging. Phone cases more than 0.2 inch / 0.5 cm thick will not be detected. Remove before charging. Charging will start automatically with a right connection and the charging indicators will light up accordingly. Charging Indicators Working Status Turns blue for 10 seconds, then Standby turns o Turns on solid blue Charging a compatible device Blue indicator turns o Device fully charged Flashes red FOD (Foreign Object Damage) alarm Specif ications Model BWA19WI1702 Input (Wireless Charger) 5V/2A, 9V/2A Output (Wireless Charger) 10W Max( Android) 7.5W Max(iPhone) Micro USB Cable Length 3 ft / 91.4 cm Dual Port Car Charger Input: DC 12V - 24V Output 1: DC 5V/2.4A Output 2: DC 3.6V-6.5V/3A, 6.5V-9V/2A, 9V-12V/1.5A Caution The charging process may give o heat so your device will become warm. Use only in cool environments. If the product gets wet, please stop the charging process immediately and remove all plugs. Do not use it before its completely dry. Do not drop, knock, or squeeze the product. Do not dismantle or throw the product in re or water to avoid causing short circuit leakage. Do not use the wireless charger in severely hot, humid, or corrosive environments to avoid circuit damage and leakage. Do not use the charger if it has excessive dents, punctures, damages, or deformities. Do not place close to magnetic stripe or chip card (ID card, bank cards, etc.) to avoid magnetic failure. Make sure the back of your phone or phone case is even without foreign metal objects. Keep at least 20 cm / 7.9 in away from implantable medical devices
(pacemakers, implantable cochlear, etc.) to avoid potential magnetic interference. Keep away from children. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment o and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help Caution: The user is cautioned that changes or modications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and(2) this device must accept any interference received, including interference that may cause undesired operation. FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator and your body.This transmitter must not be co-located or operating in conjunction with any other antenna or transmit The Qi symbol is a trademark of the Wireless Power Consortium.