www.supremainc.com BioLite NET Innovative Fingerprint Terminal User Guide (ver 1.0) User guide( ver 1.0 ) Product Contents
Basic Contents Product Contents Product Contents EE--ringring Main Body Main Body Default Default Sub bracket Sub b c e
(optional) Wall-mounting metal bracket Shrinking Tube Shrinking Tube 12V power adaptor
(optional) Before Start Recommended power supply
12V 10%, at least 2500mA for BioLite-NET alone installation. Comply with standard IEC/EN 60950-1
(CE Certification). To share the power with other devices, use a power supply with higher current ratings. Copyright 2008 Suprema Inc. 2 Cable spec. Power & 485 Relay Ethernet Switch & Wiegand PIN 1 1 2 3 4 5 PIN PIN 1 2 3 PIN 1 2 3 4 PIN 1 2 3 4 5 6 7 POWER + 485 POWER (12Vd ) POWER + (12Vdc) POWER GND 485 GND 485 +
485 -
RELAY RELAY NORMAL CLOSE COMMON NORMAL OPEN SWITCH ERX -
ERX +
ETX -
ETX +
SWITCH&WIEGAND WGND WDATA 1 WDATA 0 GND SWIN 1 GND SWIN 0 WIRE RED RED BLACK WHITE(Black String) BLUE(Black String) YELLOW(Black String) WIRE WIRE ORANGE(White String) GREEN(White String) GRAY(White String) WIRE YELLOW BLUE ORANGE PINK WIRE BLACK WHITE GREEN GRAY BROWN GRAY PURPLE Before Start Copyright 2008 Suprema Inc. 3 Power Connection
Recommended power supply
12V 10%, at least 1000mA.
To share the power with other devices, use a power supply with higher current ratings. Copyright 2008 Suprema Inc. 4 Relay Connection Fail safe lock Copyright 2008 Suprema Inc. 5 Relay Connection Fail secure lock Copyright 2008 Suprema Inc. 6 Relay Connection - Automatic door Copyright 2008 Suprema Inc. 7 Door switch connection Door Status Request To q Exit BioLite NET 1 4
(1) SW0 Input (PURPLE)
(1) SW0 Input (PURPLE)
(2) SW0 GND (GRAY)
(3) SW1 Input (BROWN)
(4) SW1 GND (GRAY) Copyright 2008 Suprema Inc. 8 Switch connection (Alarm, Emergency switches) Copyright 2008 Suprema Inc. 9 RS485 connection for host communication Before Start Copyright 2008 Suprema Inc. 10 RS485 connection for Secure I/O
(1) Power 12V (Red)
(2) Power GND (Black)
(3) Signal GND (White)
(4) TRX+ (Blue)
(5) TRX- (Yellow) BioLite NET (Master) Power Power
(1) Power 12V (Red)
(2) Power GND (Black)
(3) Signal GND (White)
(4) TRX+ (Blue)
(5) TRX- (Yellow) BioLite NET (Slave)
*Enable termination
N t 1)
(optional, see Note1) ti l TRX GND TRX+
TRX-
Secure I/O
... TRX GND TRX+
TRX-
Secure I/O As short as possible (Note 2)
*E bl
*Enable termination
(optional, see Note1) ti t i Important Notes 1. For bus termination, only the devices at both ends of the bus should be terminated. l To enable termination on the RS232-485 converter, refer to the converters manual. T 2. The stubs should be as short as practical th RS232 485 th bl ti t t f t t i Copyright 2008 Suprema Inc. 11 Installation Reference - Stand alone Copyright 2008 Suprema Inc. 12 Installation Reference Using Secure I/O, 2 door RTE switch Switch 0 Switch 0 RTE switch Internal Relay RS485 Secure I/O Relay 0 Door 0 Door 0 Door Status Switch 1 Switch 1 Door 1 Door Status Copyright 2008 Suprema Inc. 13 Copyright 2008 Suprema Inc. 14 Installation Reference Using RFID card item Model Transmit Receive Modulation Communication Channel Mode BioLite-NET(BLN-OC)
content 13.56MHz 13.56MHz ASK Single propagation Single channel 1:1
Using RFID card (13.56MHz = Mifare model only)
In case 1:1 mode is set as RF Card
If the 1:1 mode is set as Card Only, user can access just by placing the card to BioLite-NET without any additional procedure. Copyright 2008 Suprema Inc. 15 Installation Reference LAN Switch 0 RTE switch Network hub Ethernet RS485 Secure I/O I/O Relay 0 Door 1 Door Status Switch 1
If you select Network on initial UI menu, Network Setup menus appear on the display. If you select TCP/IP on network menu, following menus appear on the display. LAN TYPE Max conn SSL DHCP
Setting : Disable/Ethernet
Used when connected to PC via Ethernet using RJ45 connector on the rear of the device.
Setting : 1/4/8/16
Max number of clients that can access the device at the same time.
Setting : Use/not use.
It sets Use or Not Use of SSL between the TEST UI and BioLite NET
It sets Use or Not Use of SSL between the TEST_UI and BioLite-NET.
Setting : Use/not use
Using DHCP, you can receive IP address and other necessary setting from server automatically.
Check whether an appropriate DHCP server is available in your network environment before use. IP Address, gateway, subnet
Without using DHCP, IP address, gateway, and subnet need to be entered manually. Inquire necessary settings to network administrator. 16 Copyright 2008 Suprema Inc. Electrical Specification Min. Typ. Max. Notes Power Voltage (V) Voltage (V) Current (mA) RTC Battery Voltage (V) Current (mAH) Switch Input VIH (V) VIL (V) VIL (V) Pull-up resistance () TTL/Wiegand Output VOH (V) VOL (V) Pull-up resistance () Relay Switching capacity (A) Switching power (resistive) Switching voltage (V) 10 8 10.8
2.7
12 12 3 TBD TBD TBD 4.7k 5 0.8 4.7k
13 2 13.2 250 3.3 11
Use regulated DC power adaptor only Use regulated DC power adaptor only Lithium-ion rechargeable battery The input ports are pulled up with 4.7k resistors The outputs ports are open drain type, pulled up with 4.7k resistors internally 1 0.3 30W 37.5VA 110 125 30V DC 125V AC DC AC DC AC Copyright 2008 Suprema Inc. 17 Copyright 2008 Suprema Inc. 18 Troubleshooting
Fingerprint can not be read well or it takes too long.
Check whether a finger or fingerprint sensor is stained with sweet, water or dust
Retry after wiping off finger and fingerprint sensor with dry towel.
If a fingerprint is way too dry, blow on the finger and retry. g p g
, Fingerprint is entered but authorization keeps failing.
Check whether the user is restricted by door zone or time zone
Check whether the user is restricted by door zone or time zone
Inquire of administrator whether the enrolled fingerprint has been deleted from the device for some reason Authorized but door is not opened.
Check whether the time is set as lock time
Check whether the time is set as lock time.
Check whether an antipass back mode is in use. In antipass back mode, only who entered can exit. Device doesnt operate though power is connected.
Check whether a device and a bracket is well connected to each other. If not, a tamper switch is activated and the device doesnt work activated and the device doesn t work. RTC Battery caution.
Risk of explosion if battery is replaced by an incorrect type.
Dispose of used batteries according to the instructions. Copyright 2008 Suprema Inc. 19 FCC Rules Copyright 2008 Suprema Inc. 20 Tel : 82-31-710-2400 Fax : 82-31-783-4506 Copyright 2008 Suprema Inc. 21