FCC ID: G95-EWA1230 Dual Band Wi-Fi Ethernet Gateway

1 1. Before you start Carefully read the Safety Instructions and Regulatory Notices document included in your package before continuing with the installation of your Ethernet gateway. 2. Check the content of your package Your package contains the following items:

Item Description One EWA1230 Ethernet gateway A B C D User Documentation (this Quick Setup Guide, Safety Instructions &

Regulatory Notices). Other additional documents may be included. One power adapter (type may differ depending on region) One white Ethernet cable (with yellow connectors) 3. Model information I/O of EWA1230 is shown in below picture. 2 From left for right, they are:

Item Description PSU Plug in. DC-in Reset USB One USB 2.0 port. Recessed button to push. Refer 7.2 for How-to. ETH port 4 1G LAN port in yellow; 1 2.5G WAN port in RED. 4. Connect your Ethernet gateway to the Broadband service Choose your installation method To connect your Ethernet gateway to the Internet you can:

Place your Ethernet gateway behind another Internet access device. In this setup your Ethernet gateway is used as local Ethernet gateway. Follow the instructions from Connect as local Ethernet gateway below. 3 Connect as local Ethernet gateway 1 Plug the Ethernet cable with the red connectors into the red Ethernet WAN port on your gateway. Internet access device. 2 Plug the other end of the Ethernet cable into the Ethernet port of your 4. Power on your Ethernet gateway Plug the connector of the electric power supply adapter into the power inlet port of your Ethernet gateway. Plug the adapter into a nearby power outlet. 4 5. Connect your network devices We recommend you to first connect one computer/tablet (if possible via a wired connection), then complete the rest of the procedure and as a final step connect the other devices. 5.1. Connect your wired (Ethernet) devices If you want to connect a device using a wired (Ethernet) connection:

1 Take the white Ethernet cable. 2 Connect one end of the Ethernet cable to one of the yellow Ethernet ports of your Ethernet gateway. 3 Connect the other end of the Ethernet cable to your device. 4 Connect your other Ethernet devices. 5 We recommend you to first configure your Ethernet gateway (see 6. Configure your Ethernet gateway to your needs (optional) on page 5) before connecting your WiFi devices (see 5.2. Connect your WiFi devices on page 4). 5.2. Connect your WiFi devices Your Ethernet gateway has two WiFi access points:

The 5 GHz access point offers superior transfer rates, is less sensitive to interference and allows you to connect WiFi 6 (IEEE802.11a/n/ac/ax) devices that support 5 GHz. The 2.4 GHz access point allows you to connect WiFi 6

(IEEE802.11b/g/n/ac/ax) devices. Use this access point for WiFi devices that dont support 5 GHz. 5 Your Ethernet gateway supports band steering, a function that lets your Ethernet gateway automatically select the best access point for each of your connected WiFi devices. If band steering is enabled both access points will appear as one. WiFi settings label The label of your Ethernet gateway provides useful information about your WiFi network. Which is accessible through scanning of QRcode on label:

The Network Name. This name is used to identify your WiFi network. Some use the term SSID instead. The Wireless Key. This key is used to secure your WiFi network. Only devices that use this key can connect to the WiFi network. You can enter this key manually or configure it automatically using WPS. If band steering is disabled, each access point will have its own Network Name and Wireless Key. Tips To achieve optimal link quality:

Always try to reduce the number of obstacles (especially walls) between your WiFi devices to a minimum. Do not place your WiFi devices in the neighbourhood of devices that cause interference (microwave ovens, cordless phones, baby monitors, etc.). Connecting a WiFi device using WPS Push Button Configuration

(PBC) 1 Make sure that your WiFi devices supports WPS PBC and you know how to start it. For more information, consult the documentation of your WiFi device. 2 On your Ethernet gateway, briefly press the WPS (

) button and release it. The WPS ( ) LED starts blinking blue slowly. 6 3 Within two minutes, start WPS PBC on your WiFi device. You will probably have to do this in one of the following ways:

Press a WPS (

Start WPS (PBC) on the user interface of your WiFi device.

) button on your WiFi device. Open a list of available networks and select the Network Name mentioned on the label of your gateway. 4 After a few seconds, your WiFi device should be connected. If the WPS (

) LED starts blinking fast, then your Ethernet gateway could not connect your WiFi device. For more information, see The WPS LED is blinking fast on page 6. Connecting a WiFi device manually On your WiFi device, proceed as follows:

1 Open the list of available WiFi networks and select the entry that contains the Network Name from the label. 2 Your WiFi device will ask you to enter the WiFi key or password. 6. Configure your Ethernet gateway to your needs

(optional) The Ethernet gateway web interface allows you to configure your Ethernet gateway using your web browser. To access the gateway web user interface:

1 Browse to http://192.168.1.1 on a computer or device that is currently connected to your Ethernet gateway (either wired or over WiFi). 2 The Ethernet gateway web interface appears. By default, you are logged in as guest. This means that some items are hidden. To view all items, click Sign In and enter admin as user name and the ACCESS KEY printed on the label of your Ethernet gateway as password. 7 7. Troubleshooting 7.1. WPS troubleshooting WPS does not start Make sure that the WiFi is on. You can check the Ethernet gateway web interface. See 6. Configure your Ethernet gateway to your needs (optional) on page 5 for more information. The WPS LED is blinking fast This indicates that your Ethernet gateway could not connect to your WiFi device. Do the following:

7.2 How to reset your Ethernet gateway If at some point you want to restore the default settings, proceed as follows:

1. Make sure that your Ethernet gateway is turned on. 2. Use a pen or an unfolded paperclip to push the recessed RESET button on your Ethernet gateway for at least 10 seconds and then release it. 3. Your Ethernet gateway restarts and applies the factory default settings. 4. Wait two minutes and then start WPS again. 5. Turn your Ethernet gateway slightly and then try again. 8 6. Obstructions may deteriorate the signal strength. Try to minimize the number of walls between the two devices and then try again. 7. Move the devices closer to each other and then try again. 8. FCC Statement FCC Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. FCC Radiation Exposure Statement This device complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment must be installed and operated in accordance with provided instructions and the antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) this device may not cause harmful interference, and 9

(2) this device must accept any interference received, including interference that may cause undesired operation. Caution!

Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. 10

WARNING: Cancer and Reproductive Harm - www.P65Warnings.ca.gov FCC ID: G95-EWA1230 This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and

(2) This device must accept any interference received, including interference that may cause undesired operation. Manufactured by Technicolor Made in Vietnam DC12V 2A E305738 E305738 Model: EWA1230GFR MAC: AAABCCCDDEEE SN: CPYYWWPPXXX DV: 6296611A Model: EWA1230GFR MAC: AAABCCCDDEEE SN: CPYYWWPPXXX DV: 6296611A WARNING: Cancer and Reproductive Harm - www.P65Warnings.ca.gov FCC ID: G95-EWA1230 This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and

(2) This device must accept any interference received, including interference that may cause undesired operation. Manufactured by Technicolor Made in China DC12V 2A

MAC: AAABCCCDDEEE SN: CPYYWWPPXXX DV: 6296611A WARNING: Cancer and Reproductive Harm - www.P65Warnings.ca.gov FCC ID: G95-EWA1230 This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and

(2) This device must accept any interference received, including interference that may cause undesired operation. Manufactured by Technicolor Made in Vietnam DC12V 2A Model: GRAX210T Model: GRAX210T E305738 E305738 MAC: AAABCCCDDEEE SN: CPYYWWPPXXX DV: 6296611A WARNING: Cancer and Reproductive Harm - www.P65Warnings.ca.gov FCC ID: G95-EWA1230 This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and

(2) This device must accept any interference received, including interference that may cause undesired operation. Manufactured by Technicolor Made in China DC12V 2A

Technicolor Connected Home USA LLC Agent Authorization Company: Technicolor Connected Home USA LLC Address: 5030 Sugarloaf Parkway, Building 6, Lawrenceville, Georgia, United States Product Name: Dual Band Wi-Fi 6 Ethernet Gateway Model Number(s): 1) EWA1230GFR, EWA1230xyz (x/y/z stands or A~Z), 2) GRAX210T Product Description: Dual Band Wi-Fi 6 Ethernet Gateway We authorize MiCOM Labs Inc., 575 Boulder Court, Pleasanton, California 94566, USA, to act on our behalf on all matters concerning the certification of above named equipment. We declare that MiCOM Labs Inc. is allowed to forward all information related to the approval and certification of equipment to the regulatory agencies as required and to discuss any issues concerning the approval application. Any and all acts carried out by MiCOM Labs on our behalf shall have the same effect as acts of our own. Signature: Kebod dy Date: 2021-06-09 Name: Robert Lyall Title: Principal Certification Engineer Company: _ Technicolor Connected Home USA LLC

Technicolor Connected Home USA LLC June 22, 2021 Federal Communications Commission Equipment Authorization Division 7435 Oakland Mills Road Columbia, MD 21046 USA Attn: OET Dept. Ref: | FCC Class II Permissive change for FCC ID: G95-EWA1230 Applicant: Technicolor Connected Home USA LLC Dear Examiner, This is to request a Class II Permissive change for FCC ID: G95-EWA1230 originally granted on 06/09/2021 and 06/10/2021. The change under this application is to added operation frequency bands: UNII-

2A & UNII-2C by software. There is no hardware modification made to the applying modular transmitter itself.

| attest that the certified device will not be capable of ad-hoc mode operation outside of the grant conditions. Sincerely, Name: Robert Lyall Date: June 22, 2021 Title: Principal Certification Engineer Signature of applicant Rhu hyW FCC Class II PC request letter Rev1.1 for ID G95-EWA1230

Technicolor Connected Home USA LLC Date: 2021-06-09 Federal Communications Commission Authorization and Evaluation Division Confidentiality Request regarding application for certification of FCC ID: G95-EWA1230 Pursuant to Sections 0.457 and 0.459 of the Commissions Rules, we hereby request confidential treatment of information accompanying this application as outlined below:

Block Diagram Schematics Operational Description Software security requirement The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these materials may be harmful to the applicant and provide unjustified benefits to its competitors. The applicant understands that pursuant to Section 0.457 of the Rules, disclosure of this application and all accompanying documentation will not be made before the date of the Grant for this application. Pursuant to DA04-1705 June 15, 2004 of the Commissions public notice, we also request temporary confidential treatment of information accompanying this application as outlined below:

Exhibit Type Internal Photos Users Manual Test Set-up Photos External Photos Short-term Confidentiality Requested: 180 days It is our understanding that all measurement test reports, FCC ID label format and correspondence during the certification review process cannot be granted as confidential documents and this information will be available for public review once the grant of equipment authorization is issued. Signature hh aed iyoll Robert Lyall

Operation Description SOFTWARE SECURITY REQUIREMENTS FOR U-NII DEVICES FCC ID: G95-EWA1230 Pursuant to KDB 594280 DO2, the overall security measures-and systems that ensure that:

1. only properly authenticated software is loaded and operating the device; and 2. the device is not easily modified to operate with RF parameters outside of the authorization. are described. The following questions are addressed the description of the software in the operational description for the device and clearly how the device meets the security requirements. SOFTWARE SECURITY DESCRIPTION General |1. Describe how any software/firmware Software/firmware will be obtained by the factory, Description updates for elements than can affect the | downloaded and validated from the ODM website, devices RF parameters will be obtained, | and installed by the end user. downloaded, validated and installed. For software that is accessed through manufacturers website or devices management system, describe the different levels of security as appropriate. Software is accessed through Web UI when computer is connected. Describe the RF parameters that are modified by any software/firmware without any hardware changes. Are these parameters in some way limited such that any other software/firmware changes will not allow the device to exceed the authorized RF characteristics?

The RF parameters cannot be modified by software. All these parameters will not exceed the authorized parameters. The firmware has been complied as binary file. It couldnt change the setting RF parameter through this binary file. It is read-only without change. Describe in detail the authentication protocols that are in place to ensure that the source of the RF-related software/firmware is valid. Describe in detail how the RF-related software is protected against modification. No any authentication protocol is used. The RF Parameters is put in read-only partition of EUTs flash and are only installed in the factory. RF parameters including frequency of operation, power setting, modulation type, antenna types or country code setting will be locked in this partition. Describe in detail any encryption No encryption methods used. methods used to support the use of legitimate RF-related software/firmware. For a device that can be configured as a master and client (with active or passive scanning), explain how the device ensures compliance for each mode? In particular if the device acts as master in This device cannot be configured as a master and client. Third-Party | 1. some band of operation and client in another; how is compliance ensured in each band of operation?

Explain if any third parties have the capability to operate a U.S.-sold device on any other regulatory domain, frequencies, or in any manner that may allow the device to operate in violation of the devices authorization if activated in the U.S. Describe, if the device permits third-party software or firmware installation, what mechanisms are provided by the manufacturer to permit integration of such functions while ensuring that the RF parameters of the device No any third parties have the capability to operate a US sold device on any other regulatory domain, frequencies, or in any manner that may allow the device to operate in violation of the devices authorization if activated in the U.S. The RF Parameters is put in read-only partition of EUTs flash and are only installed in the factory. RF parameters including frequency of operation, power setting, modulation type, antenna types or cannot be operated outside its authorization for operation in the U.S. In the description include what controls and/or agreements are in place with providers of third-party functionality to ensure the devices underlying RF parameters are unchanged and how the manufacturer verifies the functionality. country code setting will be locked in this partition. For Certified Transmitter modular devices, describe how the module grantee ensures that host manufacturers fully comply with these software security requirements for U-NIl devices. If the module is controlled through driver software loaded in the host, describe how the drivers are controlled and managed such that the modular transmitter RF parameters are not modified outside the grant of authorization. SOFTWARE CONFIGURATION DESCRIPTION GUIDE For devices which have User Interfaces (Ul) to configure the device in a manner that may impact the operational RF parameters, the following questions shall be answered by the applicant and the information included in the operational description. The description must address if the device supports any of the country code configurations or peer-peer mode communications discussed in KDB 594280 Publication DO1. SOFTWARE CONFIGURATION DESCRIPTION USER 1. Describe the user configurations permitted | Authorized channel, bandwidth, and CONFIGURATION through the UI. If different levels of access modulation can be configured through GUIDE are permitted for professional installers, the UI. system integrators or end-users, describe the differences. a. What parameters are viewable and Authorized channel, bandwidth, and configurable by different parties? modulation. b. What parameters are accessible or This is not professional install device. This is not a module device. There are no different levels of access. modifiable by the professional installer or system integrators?

(1) Are the parameters in some way limited, | This is not professional install device. so that the installers will not enter parameters that exceed those authorized?

(2) What controls exist that the user cannot | The RF Parameters is put in read-only operate the device outside its partition of EUTs flash and are only authorization in the U.S.? installed in the factory. RF parameters including frequency of operation, power setting, modulation type, antenna types or country code setting will be locked in this partition. c. What parameters are accessible or Authorized channel, bandwidth, and modifiable by the end-user? modulation.

(1) Are the parameters in some way limited, so that the user or installers will not enter parameters that exceed those authorized?

This is not professional install device.

(2) What controls exist so that the user cannot operate the device outside its authorization in the U.S.?

The RF Parameters is put in read-only partition of EUTs flash and are only installed in the factory. RF parameters including frequency of operation, power setting, modulation type, antenna types or country code setting will be Jocked in this partition. d. Is the country code factory set? Can it be | Yes, the country code is set by factory. changed in the UI? It cannot be changed in the UI.

(1) If it can be changed, what controls The country code cannot be changed in exist to ensure that the device can the UI. only operate within its authorization in the U.S.?

e. What are the default parameters when the device is restarted?

Factory setting. 2. Can the radio be configured in bridge or mesh mode? If yes, an attestation may be required. Further information is available in KDB Publication 905462 D02. Fora device that can be configured as a master and client (with active or passive scanning), if this is user configurable, describe what controls exist, within the UI, to ensure compliance for each mode. If the device acts as a master in some bands and client in others, how is this configured to ensure compliance?

No, this device cannot be configured in both bridge and mesh mode. This device cannot be configured as a master and client. For a device that can be configured as This device cannot be configured as different types of access points, such as point-to-point or point-to-multipoint, and use different types of antennas, describe what different types of access points. controls exist to ensure compliance with applicable limits and the proper antenna is used for each mode of operation. (See Section 15.407(a)) Date: 2021.05.14 Name: Robert Lyall Telephone: 678-232-3668 E-mail: Robert.Lyall@technicolor.com Signature: Adak

Model Declaration Letter We, the undersigning company Company Name: Technicolor Connected Home USA LLC Address: 5030 Sugarloaf Parkway, Building 6, Lawrenceville, Georgia, United States 30044 Hereby confirm that the following products:

Product description: Dual Band Wi-Fi 6 Ethernet Gateway Type designation: EWA1230GFR, EWA1230xyz (x/y/z stands or A~Z), GRAX210T Trademark: technicolor, Google Fiber That All versions of the Model EWA1230GFR, GRAX210T, EWA1230xyz (x/y/z stands or A~Z) are electrically equal except the following difference:

1. All models are identical and xyz changes represent different country distributions for marketing purpose. 2. Model EWA1230GFR, EWA1230xyz (x/y/z stands or A~Z) trademark is technicolor, model GRAX210T trademark is Google Fiber. Date: 2021.05.14 Name: Robert Lyall Telephone: 678-232-3668 E-mail: Robert.Lyall@technicolor.com ne ML

Technicolor Connected Home USA LLC Declaration of Authorization We Name: Technicolor Connected Home USA LLC Address: 5030 Sugarloaf Parkway, Building 6 City: Lawrenceville Country: United States Declare that:

Name Representative of agent: Ms. Rose Liu Agent Company name: BTL Inc. Address: No.3 Jinshagang 1% Road, Shixia, Dalang Town City: Dong Guan Country: China is authorized to apply for Certification of the following product(s) and signing all the related documents including 731 forms:

Product description: | Dual Band Wi-Fi 6 Ethernet Gateway , Type designation: EWA1230GFR, EWA1230xyz (x/y/z stands or A~Z), GRAX210T Trademark: technicolor, Google Fiber FCC ID: G95-EWA1230 on our behalf. Date: 2021-05-14 City: Lawrenceville Name: Robert Lyall Function: Principal Certification Engineer Signature: fut

Technicolor Connected Home USA LLC FCC Software Configuration Control Declaration Date: June 9, 2021 Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 USA Attn: OET Dept. Product/ Model Number: Dual Band Wi-Fi 6 Ethernet Gateway/1) EWA1230GFR, EWA1230xyz (x/y/z stands or A~Z), 2) GRAX210T Regarding FCC Country Code Selection guidelines identified in KDB 594280. All applications for equipment authorization for transmitters that can have radio parameters, or other technical parameters, reported to the Commission set by software must have an attestation indicating that no third party will have software, or configuration control, to program the device out of compliance of the technical rules under which it has been certified. We declare that no third party will have software, or configuration control, to program the device out of compliance of the technical rules under which it has been certified. Name: Robert Lyall Date: 2021-06-09 Title: Principal Certification Engineer Signature of applicant bi dyell FCC Software Configuration Control Declaration Rev1.1