FCC ID: 2ADYY-KI7S Mobile Phone

TECNO SPARK 10 Pro User Manual Explosion diagram Explosion specification diagram specification 6.78HD+V 1 LCM CONDUCT FOAM 1 3 FRG FRAPHITE 5 P_SENSOR MYLAR 7 REC PET 9 PL GUIDE 11 FRONT FLASHLENS 13 15 ADHESIVE FLASH 17 WATERPROOF FOAM SIDEKEY FPC 19 REC FOAM 21 CONDUCTIVE SPONGE 23 FCAM 25 RECEIVER 27 REC FPC 29 SCREW 31 FRO CAM PRESS FOAM 33 35 BAT WATERPROOF PORON 37 MAIN CAM FOAM FLA GUIDE 39 FLA GUL FOAM 41 43 VICE CAM LENS ADHESIVE 45 MAIN CAM LENS BAT PORON 47 FLA PCB GRAPHITE 49 SCREW 51 CHARGER SHIELD GRAPHITE 53 BAT GRAPHITE 55 57 FG BTB PRESS FOAM 59 MAIN PCB BTB PRESS FOAM 61 63 65 67 MOTO SCREW 69 LCM FPC ADHESIVE 71 SCREW 73 SPEAKER FOAM 75 BATTERY BTB PRESS FOAM ANT MAIN SPK LCM CONDUCT FOAM 2 2 REC DECO 4 FLASH MYLAR 6 FCAM SEAL FOAM 1 8 SIM RUBBER 10 SIDEKEY FPC CONDUCT 12 PL RUBBER 14 16 ADHESIVE P SENSOR 18 WATERPROOF MEMBRANE FCAM SEAL FOAM2 20 CAM PRESS FOAM 22 SIM FOAM 24 BAT ADHESIVE 1 26 COAXIAL 28 30 PCBA 32 MAIN BACK CAM VICE CAM 34 CARD DOO 36 FLA GUL ADHESIVE 38 40 REAR CAM COPPER FOIL 42 MAIN CAM LENS ADHESIVE FLA LENS ADHESIVE 44 FLA LENS 46 RF SHIELD GRAPHITE 48 BOTTOM SHIELD GRAPHITE 50 CHARGER SHIELD GRAPHITE 52 SCREW REA 54 PEAR 56 VICE CAM BTB PRESS FOAM 58 VICE CAM SUPPORT FOAM 60 VICE CAM FOAM 62 FINGER 64 SPK FPC 66 SUB PCBA 68 BATTERY 70 BAT ADHESIVE 3 72 BOX 74 JACK RUBBER 76 SPK FRONT FOAM SPEAKER RUBBER SPEAKER CONDUCT FOAM 77 79 81 83 MIC FOAM 85 FRP HSG USB RUBBER USB CONDUCT FOAM 78 80 82 MIC RUBBER SPEAKER NET 84 86 WATERPROOF MALAR Know your phone 1. Front camera 2. Volume +key 3. Volume -key 4. Power key & side fingerprint sensor 5. Earphone jack 6. USB port 7. Camera 8. NFC SIM/SD card installation 1. Power off mobile. 2. Refer to the following picture for SIM / SD card installation. Charging the phone You can charge your device using a charger or by connecting it to the computer using a USB cable (comes with the phone). Use only TECNO charger and cables. Other chargers or cables may damage the device. This will invalidate your phone warranty. FCC Caution Labelling requirements. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference.

(2) This device must accept any interference received, interference that may cause undesired operation. including Information to user. Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Information to the user. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful installation. This interference in a residential equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

-Reorient or relocate the receiving antenna.

-Increase the separation between the equipment and receiver.

-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

-Consult the dealer or an experienced radio/TV technician for help. Specific Absorption Rate (SAR) information:

This mobile phone meets the government's requirements for exposure to radio waves. The guidelines are based on standards that were developed by independent scientific organizations through periodic and thorough evaluation of scientific studies. The standards include a substantial safety margin designed to assure the safety of all persons regardless of age or health. FCC RF Exposure Information and Statement The SAR limit of USA

(FCC) is 1.6 W/kg averaged over one gram of tissue. Device types:

KI7s (FCC ID: 2ADYY-KI7S) has also been tested against this SAR limit. The highest SAR value reported under this standard during product certification for use at the ear is 1.320W/kg and when properly worn on the body is 0.603W/kg. This device was tested for typical body-worn operations with the back of the handset kept 10 mm from the body. To maintain compliance with FCC RF exposure requirements, use accessories that maintain a 10 mm separation distance between the user's body and the back of the handset. The use of belt clips, holsters and similar accessories should not contain metallic components in its assembly. The use of accessories that does not satisfy these requirements may not comply with FCC RF exposure requirements, and should be avoided. Body-worn Operation This device was tested for typical body-worn operations. To comply with RF exposure requirements, a minimum separation distance of 1.0 cm must be maintained between the users body and the handset, including the antenna. Third-party belt-clips, holsters, and similar accessories used by this device should not contain any metallic components. Body-worn accessories that do not meet these requirements may not comply with RF exposure requirements and should be avoided. Use only the supplied or an approved antenna. HiOS runs on AndroidTM OS. Android is a trademark of Google LLC.