FCC ID: 2ALEPT0006600 Kona Micro PoE Gateway is a LoRa base station

KONA MICRO POE GATEWAY USER GUIDE Document Type:

User Guide Document Number:

T0006600_UG Document Issue:

1.4 Document Status:

Approved Product Name:

Kona Micro PoE Gateway Product Code:

See Table 1 Issue Date:

February 12, 2020 PROPRIETARY:

The information contained in this document is the property of TEKTELIC Communications Inc. Except as specifically authorized in writing by TEKTELIC, the holder of this document shall keep all information contained herein confidential, and shall protect the same in whole or in part from disclosure to all third parties. 2020 TEKTELIC Communications Inc., all rights reserved. All products, names, and services are trademarks and registered trademarks of their respective companies. TEKTELIC Communications Inc. 7657 10th Street NE Calgary, AB, Canada T2E 8X2 Phone: (403) 338-6900 Document Revision Revision Issue Date Status Editor Comments 0.1 1.0 1.1 1.2 1.3 1.4 Obsolete Oct. 8, 2019 Obsolete Oct. 17, 2019 Obsolete Nov. 6, 2019 Approved S. Morrison Dec. 20, 2019 February 12, 2020 Approved T. Danshin Z. Herasymiuk S. Morrison Z. Herasymiuk February 12, 2020 Approved T. Danshin First release Updated to new format Updated Sec. 1.2, Figure 2, Table 2 Final updates & corrections Simplified Table 1 (NA products only), updated FCC minimum distances. Corrected ISED notice T-code, clarified antenna statements and included French translation Kona Micro PoE Gateway TEKTELIC Communications Inc. T0006600_UG Confidential Version 1.4 Page 2 of 15 Table of Contents List of Tables ................................................................................................................................... 4 1 Product Description ................................................................................................................. 5 1.1 Overview .......................................................................................................................... 5 1.2 1.3 Physical Interfaces ............................................................................................................ 7 Specifications.................................................................................................................... 7 2 Installation ............................................................................................................................... 9 2.1 Overview .......................................................................................................................... 9 2.2 Unpacking and Inspection ................................................................................................ 9 2.3 2.4 2.5 2.6 2.7 Kona Micro PoE Gateway Mounting ................................................................................ 9 DC Power Cable Installation ........................................................................................... 11 Battery Installation ......................................................................................................... 12 RF Cable Installation ....................................................................................................... 13 Copper Ethernet Cable Installation ................................................................................ 13 Radio Compliance Statements .............................................................................................. 14 3 Kona Micro PoE Gateway TEKTELIC Communications Inc. T0006600_UG Confidential Version 1.4 Page 3 of 15 List of Tables Table 1: Kona Micro Gateway Models ............................................................................................ 5 Table 2: Kona Micro PoE Gateway Interface Connector Types ...................................................... 7 Table 3: Kona Micro PoE Gateway Specifications ........................................................................... 8 Kona Micro PoE Gateway TEKTELIC Communications Inc. T0006600_UG Confidential Version 1.4 Page 4 of 15 1 Product Description 1.1 Overview The Kona Micro PoE Gateway is a LoRaWAN IoT gateway that supports the full range of LoRa WAN channels. The Gateway supports one external LoRa antenna, copper Ethernet backhaul, and optional 3G/4G wireless backhaul. All Gateway models are powering from an AC-DC power adapter and may optionally have an internal backup battery provisioned. Table 1 presents the currently available Kona Micro PoE Gateway models. Any model may have a backup battery provisioned. Table 1: Kona Micro PoE Gateway Models Model T0006268 T0006267 3G/4G modem Yes No Region Frequency Band North America North America 915 915 Supports Battery Backup Yes Yes Figure 1 illustrates the Kona Micro PoE Gateway external form-factor with the front view on the top and rear view on the bottom. All models share the same mechanical form-factor. Kona Micro PoE Gateway TEKTELIC Communications Inc. T0006600_UG Confidential Version 1.4 Page 5 of 15 Figure 1: Kona Micro PoE Gateway Kona Micro PoE Gateway TEKTELIC Communications Inc. T0006600_UG Confidential Version 1.4 Page 6 of 15 1.2 Physical Interfaces Figure 2 illustrates the connector layout for the Kona Micro PoE Gateway. DC Power Ethernet

(PoE Compliant) LoRa RF Antenna Figure 2: Kona Micro Gateway Bulkhead Layout The Gateway connectors are listed in Table 2. Table 2: Kona Micro PoE Gateway Interface Connector Types Interface Connector Type Mating Connector LoRa Antenna Ports Reverse SMA female Industry standard Reverse SMA male DC Power Input Port Barrel Jack DC Barrel plug 2.1 mm (inner), 5.5 mm (outer) Center positive Industry standard RJ45 plug (PoE compliant) Ethernet Port RJ-45 1.3 Specifications The Kona Micro PoE Gateway specifications are listed in Table 3. Kona Micro PoE Gateway TEKTELIC Communications Inc. T0006600_UG Confidential Version 1.4 Page 7 of 15 Attribute Dimensions Weight Table 3: Kona Micro PoE Gateway Specifications Specification 120 (L) x 118 (W) x 41.5 (H) mm 336 g (0.74 lbs) with battery, 245 g (0.54 lbs) without battery Operating Temperature 0C to 40C without battery 0C to 38C with battery Relative Humidity 5 to 95 %RH Operating Altitude

-60 m to 4,000 m (-197 ft to 13,123 ft) Power Input, DC Port 12 VDC +/-10%

Power Input, PoE IEEE 802.3af, IEEE 802.3at, IEEE 802.3bt, Mode A or Mode B or 4-pair Mode 48 VDC nominal, 37 to 57 VDC operating range Power Consumption 12 W maximum DC input, 13 W maximum PoE input Battery 7.4 V Lithium Ion Ingress Protection Indoor use only Regulatory Compliance IEC 62368-1, EN 62368-1, CE FCC Pt. 15, RSS-247, EN 301 489-1 Kona Micro PoE Gateway TEKTELIC Communications Inc. T0006600_UG Confidential Version 1.4 Page 8 of 15 2 Installation 2.1 Overview The Kona Micro PoE Gateway is intended for indoor use only. The Kona Micro PoE Gateway has no internal field serviceable parts other than the battery. Other than installing or replacing the battery, the Gateway module must only be opened by an approved TEKTELIC service center. All installation practices must be in accordance with the local and national electrical codes. Ensure that the Kona Micro PoE Gateway is located to eliminate any physical hazard to people or property. The Kona Micro PoE Gateway shall be powered from the supplied AC-DC power adaptor or through Power over Ethernet (PoE). Simultaneous application of power to both inputs may result in unexpected operation and shall be avoided. Do not cover the Gateway or in any way obstruct airflow through the enclosure openings. The Kona Micro PoE Gateway may as an option contain a built-in battery. The Gateway may continue to operate after the DC power or PoE connection is removed. To completely power down the Gateway when battery backup is present, the DC power source, the PoE source, and the battery must all be disconnected. If the battery needs replacement, use only a replacement battery provided by Tektelic Communications Inc. After battery installation, ensure that the battery cover is secured using the supplied battery cover securement screws. Dispose of old batteries in accordance with regulatory requirements. 2.2 Unpacking and Inspection The following should be considered during the unpacking of a new Kona Micro PoE Gateway. 1. Inspect the shipping carton and report any significant damage to TEKTELIC. 2. Unpacking should be conducted in a clean and dry location when possible. 3. Do not discard the shipping box or foam inserts as they will be required if a unit is returned for repair or re-configuration. 2.3 Kona Micro PoE Gateway Mounting Kona Micro PoE Gateway can be placed on a flat surface or can be mounted to a wall with M3 screws to the locations on the back of the module illustrated in Figure 3. Kona Micro PoE Gateway TEKTELIC Communications Inc. T0006600_UG Confidential Version 1.4 Page 9 of 15 Mounting screw location Mounting screw location Figure 3: Kona Micro PoE Gateway Mounting Screw Locations While wall mounted, the Gateway module must be oriented with the TEKTELIC logo horizontal, parallel to the earth as shown in Figure 4. Kona Micro PoE Gateway TEKTELIC Communications Inc. T0006600_UG Confidential Version 1.4 Page 10 of 15 Figure 4: Kona Micro PoE Gateway Module Wall Mounting Orientation Ensure that the wall on which the Gateway is being mounted is secure, flat and able to support a load of at least 0.5 kg (1.1 lbs). The Kona Micro PoE Gateway wall mounting procedure is as follows:

1. Install the M3 screws into the wall. 2. Install 2 site supplied M3 screws into the wall at 60 mm (2.4) center spacing, leaving the screw heads protruding with a 3 mm gap from the wall surface. 3. Hang the Kona Micro PoE Gateway by mounting the two to keyhole slots onto the screws. 2.4 DC Power Cable Installation The Kona Micro PoE Gateway may be powered from the supplied AC power adaptor. The AC adaptor provides 12 VDC with positive inner tip as shown below in Figure 5. The connector tip is a standard DC Barrel connector-straight plug with 2.1 mm (inner), 5.5 mm (outer) diameters. Kona Micro PoE Gateway TEKTELIC Communications Inc. T0006600_UG Confidential Version 1.4 Page 11 of 15 Figure 5: DC Power Connection Polarity 2.5 Battery Installation Use only the battery provided by Tektelic Communications Inc. CAUTION: Risk of explosion if the battery is replaced by an incorrect type. Remove the battery cover by removing the two battery cover securement screws. Connect the 3-pin battery connector to the connector at the bottom of the battery compartment and then insert the battery into the battery compartment as illustrated in Figure 6. After the battery is connected and inserted, reinstall the battery cover and secure it in place using the two battery cover securement screws. Dispose of old batteries in accordance with regulatory requirements. Kona Micro PoE Gateway TEKTELIC Communications Inc. T0006600_UG Confidential Version 1.4 Page 12 of 15 Figure 6: Battery Installation 2.6 RF Cable Installation The Kona Micro PoE Gateway installation requires connection to an RF antenna. The antenna attaches to the reverse SMA connector located on the side of the Gateway. Torque the connector to 5 inlbs. The Kona Micro PoE is not protected from lighting surge as it is intended for Indoor use. Do not connect directly to an outdoor antenna. 2.7 Copper Ethernet Cable Installation The Kona Micro PoE Gateway Ethernet port may be used on a temporary basis for commissioning and maintenance or may be permanently connected for backhaul and optionally Power over Ethernet. The Ethernet cable must have minimum 24 AWG conductors and shall be rated for indoor application according to local and national electrical codes. Kona Micro PoE Gateway TEKTELIC Communications Inc. T0006600_UG Confidential Version 1.4 Page 13 of 15 3 Radio Compliance Statements Federal Communications Commission This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. 2. This device may not cause harmful interference, and This device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:

Increase the separation between the equipment and receiver. Reorient or relocate the receiving antenna. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. To comply with FCC/IC RF exposure limits for general population / uncontrolled exposure, the antennas used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter. Industry Canada This Device complies with Industry Canada License-exempt RSS standard(s). Operation is subject to the following two conditions:

1. 2. This device may not cause interference, and This device must accept any interference, including interference that may cause undesired operation of the device. This radio transmitter 22504-T0006600 has been approved by Industry Canada to operate with the antenna listed below with the maximum permissible gain or lesser and required antenna impedance for the antenna indicated. Antenna types not included in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device. This device complies with IC radiation exposure limits set forth for an uncontrolled environment. This device should be installed and operated with minimum distance 0.2 m between the radiator and your body. Kona Micro PoE Gateway TEKTELIC Communications Inc. T0006600_UG Confidential Version 1.4 Page 14 of 15 This device has been designed to operate with an omni-directional antenna having a maximum gain of 0 dBi in the 923-928MHz transmit band. Antennas having a gain greater than 0 dBi are strictly prohibited for use with this device. The required antenna impedance is 50 ohms. During product operation, always keep a separation distance of at least 0.2 m from any connected antenna(s). Before servicing the product, the antenna(s) or cables, turn off the transmission function or the unit power if you have to get closer than the minimum separation distance. Industrie Canada Cet appareil est conforme aux normes RSS exemptes de licence d'Industrie Canada. Son fonctionnement est soumis aux deux conditions suivantes:

1. Cet appareil ne doit pas provoquer d'interfrences, et 2. Cet appareil doit accepter toute interfrence, y compris les interfrences pouvant entraner un fonctionnement indsirable de l'appareil. Cet metteur radio 22504-T0006600 a t approuv par Industrie Canada pour fonctionner avec l'antenne indique ci-dessous avec le gain maximal autoris ou infrieur et l'impdance d'antenne requise pour l'antenne indique. Les types d'antennes non inclus dans cette liste, ayant un gain suprieur au gain maximum indiqu pour ce type, sont strictement interdits pour une utilisation avec cet appareil. Cet appareil est conforme aux limites d'exposition aux rayonnements IC dfinies pour un environnement non contrl. Cet appareil doit tre install et utilis une distance minimale de 0,2 m entre le radiateur et votre corps. Cet appareil a t conu pour fonctionner avec une antenne omnidirectionnelle ayant un gain maximum de 0 dBi dans la bande de transmission 923-928MHz. Les antennes ayant un gain suprieur 0 dBi sont strictement interdites pour une utilisation avec cet appareil. L'impdance d'antenne requise est de 50 ohms. Pendant le fonctionnement du produit, gardez toujours une distance de sparation d'au moins .2 m de toute antenne connecte. Avant de rparer le produit, les antennes ou les cbles, dsactivez la fonction de transmission ou l'alimentation de l'unit si vous devez vous rapprocher de la distance de sparation minimale. Proposition 65 WARNING: This product can expose you to chemicals including lead, beryllium, cobalt oxide, nickel oxide, carbon black and lithium nickelate & nickel, which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information, go to www.P65Warnings.ca.gov. Kona Micro PoE Gateway TEKTELIC Communications Inc. T0006600_UG Confidential Version 1.4 Page 15 of 15

FCC ID: 2ALEPT0006600 IC ID: 22504-T0006600 Label & Location All labels are 1 x 2 PLACE SAFTY AND REGULATORY LABEL AT LOCATION SHOWN Label & Location FCC ID: 2ALEPT0006600 IC ID: 22504-T0006600 Label Detail for T0006268 Label & Location FCC ID: 2ALEPT0006600 IC ID: 22504-T0006600 Label Detail for T0006267

Federal Communications Commission Authorization and Evaluation Division 1435 Oakland Mills Road Columbia, MD 21046 Date: February 10, 2020 SUBJECT: FCC ID: 2ALEPT0006600 To Whom It May Concern:

We, the undersigned, hereby authorize Marc Rousseau at Electronics Test Centre Airdrie

(MPB Technologies Inc.) on our behalf, to apply to the Federal Communications Commission on our equipment. Any and all acts carried out by Electronics Test Center Airdrie (MPB Technologies Inc.) on our behalf shall have the same effect as acts of our own. This is to advise that we are in full compliance with the Anti- Drug Abuse Act. We, the applicant, are not subject to a denial of federal benefits pursuant to Section 5301 of the Anti-

Drug Act of 1988, 21 USC853a, and no party to the application is subject to a denial of federal benefits pursuant to that section. Regards, Tom Danshin, P.Eng Senior System Engineer TEKTELIC Communications Inc.

Federal Communications Commission Authorization and Evaluation Division Confidentiality Request regarding application for certification of FCC ID: 2ALEPT0006600 Pursuant to Sections 0.457 and 0.459 of the Commissions Rules, we hereby request confidential treatment of information accompanying this application as outlined below:

Exhibit Type Block Diagram, Schematics, Operational Description, Parts List, Tune Up Info The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these materials may be harmful to the applicant and provide unjustified benefits to its competitors. The applicant understands that pursuant to Section 0.457 of the Rules, disclosure of this application and all accompanying documentation will not be made before the date of the Grant for this application. Sincerely, File Name T0006600_BlkDia.pdf T0006600_Sch.pdf T0006600_OpDesc.pdf T0006600_PartList.pdf T0006600_TuneProc.pdf Tom Danshin Rev 11/20/07

TEKTELIC COMMUNICATIONS INC. Document type: PRODUCT INTEGRITY TEST PLAN Document number: T0006600_Family_Certification_Information Document version: 1.3 Document Status: Approved Product name: Kona Micro Indoor Gateway Product codes: T0006267, T0006268 PROPRIETARY:

The information contained in this document is the property of Tektelic Communications Inc. Except as specifically authorized in writing by Tektelic, the holder of this document shall keep all information contained herein confidential, and shall protect the same in whole or in part from disclosure to all third parties. Copyright 2020 Tektelic Communications Inc. All Rights Reserved. TEKTELIC Communications Inc. Revision History Version Date Comments 1.0 1.1 1.2 1.3 February 10, 2020 February 11, 2020 February 12, 2020 Initial Release Fixed typos in table 1-1. Updated block diagram to show 2 cellular antennas. Fixed document number in footer February 18, 2020 Removed block diagram and reference Product Integrity Test Plan TEKTELIC Communications Inc. T0006600_PITP_FCI Confidential Version 1.3 Page 2 of 6 TEKTELIC Communications Inc. Family Certification Information ............................................................................................. 4 References ............................................................................................................................... 6 Contents 1 2 Product Integrity Test Plan TEKTELIC Communications Inc. T0006600_PITP_FCI Confidential Version 1.3 Page 3 of 6 TEKTELIC Communications Inc. 1 Family Certification Information The T0006600 Kona Micro PoE Gateway family consists of two variants with backhaul options

(3G/4G cellular wireless yes/no). All variants have a copper Ethernet port that is also the 802.3af PoE power interface. All variants use the same internal T0004850 radio/digital PCBA. The individual LoRa transceivers in each variant are all electrically identical. The 3G/4G radio modem options are integrated internally at the factory by installing approved commercial modules into connectors on the radio/digital PCBA. If a modem is installed, so is an internal 3G/4G cellular antenna. There is no post factory module configuration allowed. Table 1-1 presents the Gateway variants which are being certified. For the purposes of design verification and certification, one variant may be considered as covering all test cases. Table 1-1 Kona Micro Indoor Variants Variant Hardware Version ID

(HVIN) Product Description Direct DC or PoE Power Copper Eth. 3G/4G with internal Ant. LoRa Ant.

-1 T0006267

-2 T0006268 LORA GATEWAY MODULE, KONA MICRO, PoE, NA LORA GATEWAY MODULE, KONA MICRO, PoE, NA, LTE MODEM 1 1 1 1 0 1 1 1 An illustration of the common Kona Micro Indoor Gateway dimensions can be seen in Figure 1-1. Product Integrity Test Plan TEKTELIC Communications Inc. T0006600_PITP_FCI Confidential Version 1.3 Page 4 of 6 TEKTELIC Communications Inc. Figure 1-1 Kona Micro Indoor Gateway The bulkhead connectors are identical for all of the variants. Product Integrity Test Plan TEKTELIC Communications Inc. T0006600_PITP_FCI Confidential Version 1.3 Page 5 of 6 TEKTELIC Communications Inc. 2 References There are no sources in the current document. Product Integrity Test Plan TEKTELIC Communications Inc. T0006600_PITP_FCI Confidential Version 1.3 Page 6 of 6