AMPAK Technology Inc. Advanced Module Packaging Solution CC2564MODNEM User manual Date 2013/12/24 Revision History Revision Content Initial released Revised By Version Rue 1.0 AMPAK Technology Inc. www.ampak.com.tw Proprietary & Confidential Information i Doc. NO:
Contents 1. CC2564MODN evaluation module introduction ....................................................... 1 2. PIN Description/ Operating Ratings/ Operating temperature ................................. 3 3. Federal Communication Commission Interference Statement ................................ 6 4. Industry Canada statement ......................................................................................... 7 AMPAK Technology Inc. www.ampak.com.tw Proprietary & Confidential Information i Doc. NO:
1. CC2564MODN evaluation module introduction CC2564MODN evaluation module (EM) likes as figure1. That is designed for Bluetooth 2.1+EDR application. The bottom views like as figure2. It is also designed for TIs MSP430 experimenter board. It is subject to provide a convenient environment for customers verification on Bluetooth function. There are controller pins on evaluation board which describes as below. Figure1. Top view of CC2564MODNEM AMPAK Technology Inc. www.ampak.com.tw Proprietary & Confidential Information Doc. NO:
1 Figure2. Bottom view of CC2564MODNEM Interface highlights:
1. U5: CC2564MODN SIP module. 2. P3: U.FL connector let RF signal in/out path, which R30 need tie on 0ohm. 3. J4: VBAT_MCU: 3V3 for main system power path form RF2. 4. J3: VBAT_EDGE: 3V3 for main system power path form P2 5. J2&R10: VBAT_CC: 3V3 for CC2564MODN main power 6. J1&R7: VDO_1V8: V8 for system IO level path 7. RF1&RF2&P2: For TIs experimenter board IO used. AMPAK Technology Inc. www.ampak.com.tw Proprietary & Confidential Information Doc. NO:
2 2. PIN Description/ Operating Ratings/ Operating temperature 2.1 PIN Description Connector RF1 RF2 No. 1,19 3 5 7 9 others 2 7,9 8 10 11 17 18 19 others Pin Name GND HCI_CTS_3V3 SLOW_CLK_3V3 HCI_RX_3V3 HCI_TX_3V3 Not connected GND
+3V3 AUD_OUT_3V3 AUD_IN_3V3 AUD_FSYNC_3V3 AUD_CLK_3V3 HCI_RTS_3V3 nSHUTD_3V3 Not connected Def. Dir. I I I O I O I I/O I/O O I Description of Options (Common) Connect to ground HCI UART clear-to-send 32.768-KHz clock in HCI UART data receive HCI UART data transmit Connect to ground Connect to +3.3V PCM data output PCM data input PCM frame synch PCM clock HCI UART request-to-send Shutdown input (active low) AMPAK Technology Inc. www.ampak.com.tw Proprietary & Confidential Information Doc. NO:
3 Connector No. Pin Name P2 SLOW_CLK_EDGE 1V8_IN AUD_CLK_1V8 AUD_FSYNC_1V8 AUD_IN_1V8 AUD_OUT_1V8 HCI_TX_1V8 HCI_RX_1V8 HCI_CTS_1V8 HCI_RTS_1V8 TX_DEBUG_1V8 nSHUTDOWN_1V8 GND GND 1 8 52 54 56 58 66 68 70 72 76 89 3, 9, 19, 37, 47, 63, 77, 83, 87, 95, 97, 2, 6, 18, 22, 42, 60, 64, 92 others Not connected Def. Dir. I I I/O I/O I O O I I O I I Description of Options (Common) 32.768-KHz clock in Connect to +1.8V PCM clock PCM frame synch PCM data input PCM data output HCI UART data transmit HCI UART data receive HCI UART clear-to-send HCI UART request-to-send DEBUG port use Shutdown input (active low) Connect to ground Connect to ground AMPAK Technology Inc. www.ampak.com.tw Proprietary & Confidential Information Doc. NO:
4 2.2 Operating Ratings Test conditions: At room temperature 25C Description Min. 2.2 Typ. 3.3 Input supply Voltage 2.3 Operating temperature Operating temperature
-40C to 85C Max. Unit V 4.85.5 AMPAK Technology Inc. www.ampak.com.tw Proprietary & Confidential Information Doc. NO:
5 3. Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. IMPORTANT NOTE:
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. AMPAK Technology Inc. www.ampak.com.tw Proprietary & Confidential Information Doc. NO:
6 4. Industry Canada statement This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions:
(1) this device may not cause interference, and
(2) this device must accept any interference, including interference that may cause undesired operation of the device. Le prsent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorise aux deux conditions suivantes :
(1) l'appareil ne doit pas produire de brouillage, et
(2) l'utilisateur de l'appareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible d'en compromettre le fonctionnement. Radiation Exposure Statement:
The product comply with the Canada portable RF exposure limit set forth for an uncontrolled environment and are safe for intended operation as described in this manual. The further RF exposure reduction can be achieved if the product can be kept as far as possible from the user body or set the device to lower output power if such function is available. Dclaration d'exposition aux radiations:
Le produit est conforme aux limites d'exposition pour les appareils portables RF pour les Etats-Unis et le Canada tablies pour un environnement non contrl. Le produit est sr pour un fonctionnement tel que dcrit dans ce manuel. La rduction aux expositions RF peut tre augmente si l'appareil peut tre conserv aussi loin que possible du corps de l'utilisateur ou que le dispositif est rgl sur la puissance de sortie la plus faible si une telle fonction est disponible. AMPAK Technology Inc. www.ampak.com.tw Proprietary & Confidential Information Doc. NO:
7