FCC ID: TE7WR841HPV5 300Mbps High Power Wireless N Router

by: TP-Link Technologies Co., Ltd. latest update: 2017-03-30 model: WR841HPV5

One grant has been issued under this FCC ID on 03/30/2017 (this is one of one hundred and twenty-two releases in 2017 for this grantee). Public details available include internal & external photos, manuals, and frequency information. some products also feature user submitted or linked troubleshooting guides, warrantee terms, instructions, drivers, & password defaults.

permalink for this FCC identifier

search for: Repair details

from iFixIt

Trade-in? Recycling locations

eg for Slack usage

all	frequencies		exhibits	applications
		manual

all exhibits 10
1 ~ 2017-03-30 10

app s				submitted / available
1	TL-WR841HP User manual	Users Manual	pdf	5.59 MiB
1		Cover Letter(s)	pdf
1		Cover Letter(s)	pdf
1		External Photos	pdf
1		Internal Photos	pdf
1		ID Label/Location Info	pdf
1		RF Exposure Info	pdf
1		Cover Letter(s)	pdf
1		Test Report	pdf
1		Test Setup Photos	pdf

exhibit
download
text

TL-WR841HP User manual

Users Manual

pdf

5.59 MiB

User Guide 300Mbps High Power Wireless N Router TL-WR841HP REV5.0.0 1910012102 Contents About This Guide .........................................................................................................1 Chapter 1. Get to Know About Your Router . 2 1. 1. Product Overview. 3 1. 2. Panel Layout. 3 1. 2. 1. Top View . 3 1. 2. 2. The Back Panel. 5 Chapter 2. Connect to the Internet . 6 2. 1. Position Your Router . 7 2. 2. Connect to the Internet . 7 2. 2. 1. Install the antennas . 7 2. 2. 2. Router mode . 8 2. 2. 3. Repeater/Bridge Mode . 11 2. 2. 4. Access Point Mode. 12 Chapter 3. Log In. 14 Chapter 4. Configure the Router in Standard Wireless Router. 16 4. 1. Status . 17 4. 2. Operation Mode . 18 4. 3. Network . 19 4. 3. 1. WAN. 19 4. 3. 2. LAN . 26 4. 3. 3. IPTV. 27 4. 3. 4. MAC Clone. 28 4. 4. Wireless . 28 4. 4. 1. Basic Settings. 28 4. 4. 2. WPS. 30 4. 4. 3. Wireless Security . 31 4. 4. 4. Wireless MAC Filtering . 33 4. 4. 5. Wireless Advanced. 34 4. 4. 6. Wireless Statistics . 36 4. 5. Guest Network. 36 4. 6. DHCP. 37 4. 7. 4. 6. 1. DHCP Settings . 37 4. 6. 2. DHCP Client List . 39 4. 6. 3. Address Reservation . 39 Forwarding . 40 4. 7. 1. Virtual Server . 40 4. 7. 2. Port Triggering . 42 4. 7. 3. DMZ. 42 4. 7. 4. UPnP. 43 4. 8. Security . 44 4. 8. 1. Basic Security. 44 4. 8. 2. Advanced Security. 46 4. 8. 3. Local Management. 47 4. 8. 4. Remote Management . 48 4. 9. Parental Controls . 48 4. 10. Access Control . 49 4. 11. Advanced Routing . 52 4. 11. 1. Static Route List . 52 4. 11. 2. System Routing Table. 53 4. 12. Bandwidth Control. 54 4. 12. 1. Control Settings . 54 4. 12. 2. Rule List . 54 IP&MAC Binding . 55 4. 13. 1. Binding Settings . 55 4. 13. 2. ARP List . 56 4. 14. Dynamic DNS. 57 IPv6 . 59 4. 15. 4. 15. 1. IPv6 Status . 59 4. 15. 2. IPv6 WAN. 60 4. 15. 3. IPv6 LAN. 63 4. 16. System Tools . 64 4. 16. 1. LED Control. 64 4. 16. 2. Time Settings. 65 4. 16. 3. Diagnostic. 66 4. 16. 4. Firmware Upgrade . 67 4. 16. 5. Factory Defaults . 68 4. 16. 6. Backup & Restore. 68 4. 16. 7. Reboot . 69 4. 16. 8. Password . 69 4. 16. 9. Language. 70 4. 13. 4. 16. 10. System Log . 70 4. 17. Log Out. 70 Chapter 5. Configure the Router in Access Point Mode . 71 5. 1. Status . 72 5. 2. Operation Mode . 73 5. 3. Network . 73 5. 3. 1. LAN. 73 5. 4. Wireless . 74 5. 4. 1. Basic Settings. 74 5. 4. 2. WPS. 76 5. 4. 3. Wireless Security . 77 5. 4. 4. Wireless MAC Filtering . 79 5. 4. 5. Wireless Advanced. 80 5. 4. 6. Wireless Statistics . 81 5. 4. 7. Throughput Monitor. 82 5. 5. DHCP. 83 5. 5. 1. DHCP Settings . 83 5. 5. 2. DHCP Clients List . 84 5. 5. 3. Address Reservation . 85 5. 6. System Tools . 85 5. 6. 1. LED Control. 85 5. 6. 2. Time Settings . 86 5. 6. 3. Diagnostic . 87 5. 6. 4. Firmware Upgrade. 88 5. 6. 5. Factory Defaults . 88 5. 6. 6. Backup & Restore . 89 5. 6. 7. Reboot. 89 5. 6. 8. Password . 90 5. 6. 9. Language . 90 5. 6. 10. System Log. 91 Log Out. 92 5. 7. Chapter 6. Configure the Router in Repeater Mode . 93 6. 1. Status . 94 6. 2. Operation Mode . 95 6. 3. Network . 95 6. 3. 1. LAN. 95 6. 4. Wireless . 96 6. 4. 1. Connect to Network. 96 6. 4. 2. Extended Network . 97 6. 4. 3. Wireless MAC Filtering . 97 6. 4. 4. Wireless Advanced. 99 6. 4. 5. Wireless Statistics . 100 6. 4. 6. Throughput Monitor. 100 6. 5. DHCP. 101 6. 5. 1. DHCP Settings . 101 6. 5. 2. DHCP Client List . 102 6. 6. System Tools . 103 6. 6. 1. LED Control. 103 6. 6. 2. Time Settings . 103 6. 6. 3. Diagnostic . 105 6. 6. 4. Ping Watch Dog. 106 6. 6. 5. Firmware Upgrade. 107 6. 6. 6. Factory Defaults . 107 6. 6. 7. Backup & Restore . 107 6. 6. 8. Reboot. 108 6. 6. 9. Password . 108 6. 6. 10. Language. 109 6. 6. 11. System Log. 110 6. 7. Log Out. 111 FAQ .............................................................................................................................112 About This Guide This guide is a complement of Quick Installation Guide. The Quick Installation Guide instructs you on quick internet setup, and this guide provides details of each function and shows you the way to configure these functions appropriate to your needs. When using this guide, please notice that features of the router may vary slightly depending on the model and software version you have, and on your location, language, and internet service provider. All screenshots, images, parameters and descriptions documented in this guide are used for demonstration only. Conventions In this guide the following conventions are used:

Convention Underlined Teal

Note:

Tips:

Description Underlined words or phrases are hyperlinks. You can click to redirect to a website or a specific section. Contents to be emphasized and texts on the web page are in teal, including the menus, items, buttons, etc. The menu structures to show the path to load the corresponding page. For example, Advanced > Wireless > MAC Filtering means the MAC Filtering function page is under the Wireless menu that is located in the Advanced tab. Ignoring this type of note might result in a malfunction or damage to the device. Indicates important information that helps you make better use of your device. symbols on the web page click to edit the corresponding entry. click to delete the corresponding entry. click to enable or disable the corresponding entry. click to view more information about items on the page. More Info The latest software, management app and utility can be found at Download Center at http://www.tp-link.com/support. The Quick Installation Guide can be found where you find this guide or inside the package of the router. Specifications can be found on the product page at http://www.tp-link.com. A Technical Support Forum http://forum.tp-link.com. Our Technical Support contact information can be found at the Contact Technical Support page at http://www.tp-link.com/support. is provided for you to discuss our products at 1 Chapter 1 Get to Know About Your Router This chapter introduces what the router can do and shows its appearance. It contains the following sections:

Product Overview Panel Layout Chapter 1 Get to Know About Your Router 1. 1. Product Overview The TP-Link router is designed to fully meet the need of Small Office/Home Office

(SOHO) networks and users demanding higher networking performance. The powerful antennas ensure continuous Wi-Fi signal to all your devices while boosting widespread coverage throughout your home, the built-in Ethernet ports supply high-speed connection to your wired devices, and the flexible working modes are capable to meet all your network needs. Moreover, it is simple and convenient to set up and use the TP-Link router due to its intuitive web interface and the powerful Tether app. 1. 2. Panel Layout 1. 2. 1. Top View RE button: This button is located on the top panel of the router. Press and hold it for about 3 seconds to change to the Range Extender mode. 3 Chapter 1 Get to Know About Your Router The routers LEDs (view from left to right) are located on the front panel. You can check the routers working status by following the LED Explanation table. LED Explanation Name RE Wi-Fi PWR WAN LAN WPS Status Blinking On On Off On Blinking Off Blue On Orange On Off On Off On/Off Blinking Indication The router is connecting to the host wireless network. This may take up to 2 minutes. The router is connected to the host wireless network, and it is working in Range Extender mode. The wireless band is enabled. The wireless band is disabled. Power is on. The system is starting up or firmware is being upgraded. Do not disconnect or power off the router. Power is off. The internet is available. The routers WAN port is connected, but the internet is not available. The routers WAN port is not connected to a powered-on device. At lease one LAN port is connected to a powered-on device. No LAN port is connected to a powered-on device. This light remains on for 5 minutes when a WPS connection is established, and then turns off. WPS connection is in progress. This may take up to 2 minutes. 4 Chapter 1 Get to Know About Your Router 1. 2. 2. The Back Panel The following parts (view from left to right) are located on the rear panel. Item Ethernet Ports (1/2/3/4) WPS WAN Port Reset Button Wi-Fi On/Off Power On/Off Power Port Antennas Description For connecting your PCs or other wired network devices to the router. If your devices, such as wireless adapters, that support Wi-Fi Protected Setup, then you can press this button to quickly establish a connection between the router and devices. For connecting to a DSL/Cable modem, or an Ethernet port. Use a pin to press and hold this button until all the LED turn on momentarily to reset the router to its factory default settings. Press and hold this button about 2 seconds to enable or disable Wireless function. For powering on or off the router. For connecting the router to a power socket via the provided power adapter. Used for wireless operation and data transmitting. Upright them for the best Wi-Fi performance. 5 Chapter 2 Connect to the Internet This chapter contains the following sections:

Position Your Router Connect to the Internet Chapter 2 Connect to the Internet 2. 1. Position Your Router The product should not be located in a place where it will be exposed to moisture or excessive heat. Place the router in a location where it can be connected to multiple devices as well as to a power source. Make sure the cables and power cord are safely placed out of the way so they do not create a tripping hazard. The router can be placed on a shelf or desktop. Keep the router away from strong devices with strong electromagnetic interference, such as Bluetooth devices, cordless phones and microwaves. 2. 2. Connect to the Internet 2. 2. 1. Please install the Antennas first by following the steps shown below before your start to use the router. Install the antennas 1. 2. B. Make sure that the adjustable elbow is facing up when attached. Slide the cap onto the antenna until it fixes into place. A. Insert and screw the antenna into the antenna socket. 3. Position the antenna vertically for best Wi-Fi performance. The Router provides three working modes: Router, Range Extender and Access Point. You can choose the mode to better suit your network needs and follow the guide to complete the configuration. 7 Chapter 2 Connect to the Internet Router mode 2. 2. 2. This mode enables multiple users to share internet connection via ADSL/Cable Modem. 1. Follow the steps below to connect your router. If your internet connection is through an Ethernet cable from the wall instead of through a DSL / Cable / Satellite modem, connect the Ethernet cable directly to the routers WAN port, and then follow Step 4 and 5 to complete the hardware connection. Modem Router 1 3 2 4 1 ) Turn off the modem, and remove the backup battery if it has one. 2 ) Connect the modem to the WAN port on your router with an Ethernet cable. 3 ) Turn on the modem, and then wait about 2 minutes for it to restart. 4 ) Connect the power adapter to the router and turn on the router. 5 ) Verify that the hardware connection is correct by checking these LEDs. RE Wi-Fi ON PWR ON WAN ON LAN WPS Tips: If Wi-Fi LED is off, press and hold the Wi-Fi On/Off button until it is on. 2. Connect your computer to the router. Method 1: Wired Turn off the Wi-Fi on your computer and connect the devices as shown below. Ethernet cable Method 2: Wirelessly 8 Chapter 2 Connect to the Internet 1 ) Find the SSID (Network Name) and Wireless Password printed on the label at the bottom of the router. 2 ) Click the network icon of your computer or go to Wi-Fi Settings of your smart device, and then select the SSID to join the network. Computer Smart Device

< Settings Wi-Fi TP-Link_XXXX Connect automatically Wireless Name OR Connect Wi-Fi CHOOSE A NETWORK... TP-Link_XXXX Wireless Name Other... Method 3: Use the WPS button Wireless devices that support WPS, including Android phones, tablets, most USB network cards, can be connected to your router through this method ( Not supported by iOS devices). Note:

The WPS function cannot be configured if the wireless function of the router is disabled. Also, the WPS function will be disabled if your wireless encryption is WEP. Please make sure the wireless function is enabled and is configured with the appropriate encryption before configuring the WPS. 1 ) Tab the WPS icon on the devices screen. 2 ) Immediately press the WPS button on your router. 4G WLAN On TP-Link_2017 TP-Link_Home My Home My Network Home Network TP-Link_Network TP-Link_Test Close to 3. Enter http://tplinkwifi.net in the address bar of a web browser. Select the language you want to use and then use admin for both username and password. Then click Login. 9 Connections are availableWireless Network Connection Chapter 2 Connect to the Internet Note:

If the above screen does not pop-up, it means that your IE Web-browser has been set to a proxy. Go to Tools menu >

Internet Options > Connections > LAN Settings, in the screen that appears, cancel the Using Proxy checkbox, and click OK to finish it. 4. After successful login, click Next to start the Quick Setup. Select Wireless Router and follow the step-by-step instructions to complete the initial configuration. 5. Enjoy! For wireless devices, you may have to reconnect to the wireless network if you have customized the SSID (network name) and password during the configuration. 10 Chapter 2 Connect to the Internet Repeater/Bridge Mode 2. 2. 3. This mode boosts your home wireless coverage. Step 1: Configure Tips:

Using WPS Button is an easy way to extend your host network. We recommend you to use this way if your host router has the WPS button. The button might look like these:

Option One: Using RE Button WPS 1 ) Press the WPS button on the host router. 2 ) Press and hold the within 1 minute. The router will start to reboot.

(RE button) on the top panel of router for about 3 seconds 3 ) Once rebooted, the RE LED should change from blinking to a solid state, indicating a successful connection. Note: If not, please refer to the Option Two. Option Two: Using Web Browser 1 ) Connect a computer to the router via an Ethernet cable or wirelessly by using the SSID (Network Name) and password printed on the label at the bottom of the router. 2 ) Enter http://tplinkwifi.net in the address bar of a web browser. Select the language you want to use and then use admin for both username and password. Then click Login. 11 Chapter 2 Connect to the Internet 3 ) After successful login, click Next to start the Quick Setup. Select Wireless Router and follow the step-by-step instructions to complete the initial configuration. 6. Relocate: Place the router between your host router and the Wi-Fi dead zone. The location you choose must be within the range of your existing host network. Host Network Extended Network Host Router High Power Router Client 7. Enjoy!The extended network shares the same SSID (Network Name) and password as your host network. 2. 2. 4. Access Point Mode This mode transforms your existing wired network to a wireless network. Internet Ethernet1 Ethernet2 Ethernet3 Ethernet1 Ethernet2 Ethernet4 Ethernet3 Ethernet4 Wired Host Router High Power Router Client 1. Turn on the router. 2. Connect the router to your wired host routers Ethernet port via an Ethernet cable as shown above. 3. Connect a computer to the router via an Ethernet cable or wirelessly by using the SSID (network name) and password printed on the bottom label of the router. 4. Enter http://tplinkwifi.net in the address bar of a web browser. Select the language you want to use and then use admin for both username and password. Then click Login. 12 Chapter 2 Connect to the Internet Note:

If the above screen does not pop-up, it means that your IE Web-browser has been set to a proxy. Go to Tools menu >

Internet Options > Connections > LAN Settings, in the screen that appears, cancel the Using Proxy checkbox, and click OK to finish it. 5. After successful login, click Next to start the Quick Setup. Select Access Point and follow the step-by-step instructions to complete the initial configuration. 6. Enjoy! Connect to the wireless network by using the SSID (network name) and password of the router. 13 Chapter 3 Log In This chapter shows how to log in to the web management page of router. Chapter 3 Log In With the web-based utility, it is easy to configure and manage the router. The web-

based utility can be used on any Windows, Macintosh or UNIX OS with a Web browser, such as Microsoft the Internet Explorer, Mozilla Firefox or Apple Safari. Follow the steps below to log in to your router. 1. Set up the TCP/IP Protocol in Obtain an IP address automatically mode on your computer. 2. Visit http://tplinkwifi.net, select the language you want to use and then use admin for both username and password. Then click Login. Note:

If the login window does not appear, please refer to the FAQ section. 15 Chapter 4 Configure the Router in Standard Wireless Router This chapter presents how to configure the various features of the router working as a standard wireless router. It contains the following sections:

Status Operation Mode Network Wireless Guest Network DHCP Forwarding Security Parental Controls Access Control Advanced Routing Bandwidth Control IP&MAC Binding Dynamic DNS IPv6 System Tools Log Out Chapter 4 Configure the Router in Standard Wireless Router 4. 1. Status 1. Visit http://tplinkwifi.net, and log in with the default username and password: admin. 2. Go to Status. You can view the current status information of the router. Firmware Version - The version information of the routers firmware. Hardware Version - The version information of the routers hardware. LAN - This field displays the current settings of the LAN, and you can configure them on the Network > LAN page. MAC address - The physical address of the router. Subnet Mask - The subnet mask associated with the LAN IP address. IP address - The LAN IP address of the router. Wireless - This field displays the basic information or status of the wireless function, and you can configure them on the Wireless > Basic Settings page. Operation Mode - The current working mode of the router. Wireless Radio - Indicates whether the wireless feature is enabled or not. Name (SSID) - The wireless network name of the router. 17 Chapter 4 Configure the Router in Standard Wireless Router Mode - The current wireless working mode. Channel - The current wireless channel. Channel Width - The current wireless channel width. MAC Address - The physical address of the router. WDS Status - The status of WDS connection. WAN - This field displays the current settings of the WAN, and you can configure them on the Network > WAN page. MAC Address - The physical address of the WAN port. IP Address - The current WAN (Internet) IP Address. This field will be blank or 0.0.0.0 if the IP Address is assigned dynamically and there is no internet connection. Subnet Mask - The subnet mask associated with the WAN IP Address. Default Gateway - The Gateway currently used is shown here. When you use Dynamic IP as the internet connection type, click Renew or Release here to obtain new IP parameters dynamically from the ISP or release them. DNS Server - The IP addresses of DNS (Domain Name System) server. System Up Time - The length of the time since the router was last powered on or reset. Click Refresh to get the latest status and settings of the router. 4. 2. Operation Mode 1. Visit http://tplinkwifi.net, and log in with the default username and password: admin. 2. Go to Operation Mode. 3. Select the Wireless Router mode as needed and click Save. 18 Chapter 4 Configure the Router in Standard Wireless Router 4. 3. Network 4. 3. 1. WAN 1. Visit http://tplinkwifi.net, and log in with the default username and password: admin. 2. Go to Network > WAN. 3. Configure the IP parameters of the LAN and click Save. Dynamic IP If your ISP provides the DHCP service, please select Dynamic IP, and the router will automatically get IP parameters from your ISP. Click Renew to renew the IP parameters from your ISP. Click Release to release the IP parameters. MTU Size - The normal MTU (Maximum Transmission Unit) value for most Ethernet networks is 1500 Bytes. It is not recommended that you change the default MTU size unless required by your ISP. Use These DNS Servers - If your ISP providess you one or two DNS addresses, select Use These DNS Servers and enter the primary and secondary addresses. Otherwise, the DNS servers will be assigned dynamically from your ISP. Host Name - This option specifies the name of the router. 19 Chapter 4 Configure the Router in Standard Wireless Router Get IP with Unicast DHCP - A few ISPs DHCP servers do not support the broadcast applications. If you cannot get the IP address normally, you can choose this option. (It is rarely required.) Static IP If your ISP provides a static or fixed IP address, subnet mask, default gateway and DNS setting, please select Static IP. IP Address - Enter the IP address in dotted-decimal notation provided by your ISP. Subnet Mask - Enter the subnet mask in dotted-decimal notation provided by your ISP. Normally 255.255.255.0 is used as the subnet mask. Default Gateway - Enter the gateway IP address in dotted-decimal notation provided by your ISP. MTU Size - The normal MTU (Maximum Transmission Unit) value for most Ethernet networks is 1500 Bytes. It is not recommended that you change the default MTU size unless required by your ISP. Primary/Secondary DNS - (Optional) Enter one or two DNS addresses in dotted-

decimal notation provided by your ISP. 20 Chapter 4 Configure the Router in Standard Wireless Router PPPoE If your ISP provides PPPoE connection, select PPPoE. User Name/Password - Enter the user name and password provided by your ISP. These fields are case-sensitive. Confirm Password - Enter the Password provided by your ISP again to ensure the password you entered is correct. Secondary Connection - Its available only for PPPoE connection. If your ISP provides an extra connection type, select Dynamic IP or Static IP to activate the secondary connection. WAN Connection Mode Connect on Demand - In this mode, the internet connection can be terminated automatically after a specified inactivity period (Max Idle Time) and be re-

established when you attempt to access the internet again. If you want to keep your internet connection active all the time, please enter 0 in the Max Idle Time field. Otherwise, enter the number of minutes you want to have elapsed before your internet access disconnects. Connect Automatically - The connection can be re-established automatically when it is down. Time-based Connecting - The connection will only be established in the period from the start time to the end time (both are in HH:MM format). Connect Manually - You can click Connect/Disconnect to connect/disconnect immediately. This mode also supports the Max Idle Time function as Connect on Demand mode. The internet connection can be disconnected automatically 21 Chapter 4 Configure the Router in Standard Wireless Router after a specified inactivity period (Max Idle Time) and not be able to re-establish when you attempt to access the internet again. Note:

Only when you have configured the system time on the System Tools > Time Settings page, will the time-

based connecting function take effect. Sometimes the connection cannot be terminated although you have specified the Max Idle Time because some applications are visiting the internet continually in the background. If you want to do some advanced configurations, please click Advanced. MTU Size - The default MTU size is 1480 bytes. It is not recommended that you change the default MTU size unless required by your ISP. Service Name/AC Name - The service name and AC (Access Concentrator) name should not be configured unless you are sure it is necessary for your ISP. In most cases, leaving these fields blank will work. ISP Specified IP Address - If your ISP does not automatically assign IP addresses to the router, please select Use IP address specified by ISP and enter the IP address provided by your ISP in dotted-decimal notation. Detect Online Interval - The router will detect Access Concentrator online at every interval. The default value is 0. You can input the value between 0 and 120. The value 0 means no detect. Primary DNS/Secondary DNS - If your ISP does not automatically assign DNS addresses to the router, please select Use the following DNS servers and enter the IP address in dotted-decimal notation of your ISPs primary DNS server. If a secondary DNS server address is available, enter it as well. 22 Chapter 4 Configure the Router in Standard Wireless Router BigPond Cable If your ISP provides BigPond cable connection, please select BigPond Cable. User Name/Password - Enter the user name and password provided by your ISP. These fields are case-sensitive. Auth Server - Enter the authenticating server IP address or host name. Auth Domain - Type in the domain suffix server name based on your location. MTU Size - The default MTU size is 1480 bytes. It is not recommended that you change the default MTU size unless required by your ISP. Connection Mode Connect on Demand - In this mode, the internet connection can be terminated automatically after a specified inactivity period (Max Idle Time) and be re-

established when you attempt to access the internet again. If you want to keep your internet connection active all the time, please enter 0 in the Max Idle Time field. Otherwise, enter the number of minutes you want to have elapsed before your internet access disconnects. Connect Automatically - The connection can be re-established automatically when it is down. Connect Manually - You can click Connect/Disconnect to connect/disconnect immediately. This mode also supports the Max Idle Time function as Connect on Demand mode. The internet connection can be disconnected automatically after a specified inactivity period (Max Idle Time) and not be able to re-establish when you attempt to access the internet again. 23 Chapter 4 Configure the Router in Standard Wireless Router Note:

Sometimes the connection cannot be terminated although you have specified the Max Idle Time because some applications are visiting the internet continually in the background. L2TP If your ISP provides L2TP connection, please select L2TP. User Name/Password - Enter the user name and password provided by your ISP. These fields are case-sensitive. Confirm Password - Enter the Password provided by your ISP again to ensure the password you entered is correct. Connect/Disconnect - Click this button to connect or disconnect immediately. Dynamic IP/ Static IP - Select either as required by your ISP. If Static IP is selected, please enter the IP address, subnet marsk, gateway and DNS also provided by your ISP. Internet IP Address/ Internet DNS - The internet IP address and DNS server address assigned by L2TP server. Connection Mode Connect on Demand - In this mode, the internet connection can be terminated automatically after a specified inactivity period (Max Idle Time) and be re-

24 Chapter 4 Configure the Router in Standard Wireless Router established when you attempt to access the internet again. If you want to keep your internet connection active all the time, please enter 0 in the Max Idle Time field. Otherwise, enter the number of minutes you want to have elapsed before your internet access disconnects. Connect Automatically - The connection can be re-established automatically when it is down. Connect Manually - You can click Connect/Disconnect to connect/disconnect immediately. This mode also supports the Max Idle Time function as Connect on Demand mode. The internet connection can be disconnected automatically after a specified inactivity period (Max Idle Time) and not be able to re-establish when you attempt to access the internet again. Note:

Sometimes the connection cannot be terminated although you have specified the Max Idle Time because some applications are visiting the internet continually in the background. PPTP If your ISP provides PPTP connection, please select PPTP. 25 Chapter 4 Configure the Router in Standard Wireless Router User Name/Password - Enter the user name and password provided by your ISP. These fields are case-sensitive. Confirm Password - Enter the Password provided by your ISP again to ensure the password you entered is correct. Connect/Disconnect - Click this button to connect or disconnect immediately. Dynamic IP/ Static IP - Select either as required by your ISP. If Static IP is selected, please enter the IP address, subnet marsk, gateway and DNS also provided by your ISP. Internet IP Address/ Internet DNS - The internet IP address and DNS server address assigned by L2TP server. Connection Mode Connect on Demand - In this mode, the internet connection can be terminated automatically after a specified inactivity period (Max Idle Time) and be re-

established when you attempt to access the internet again. If you want to keep your internet connection active all the time, please enter 0 in the Max Idle Time field. Otherwise, enter the number of minutes you want to have elapsed before your internet access disconnects. Connect Automatically - The connection can be re-established automatically when it is down. Connect Manually - You can click Connect/Disconnect to connect/disconnect immediately. This mode also supports the Max Idle Time function as Connect on Demand mode. The internet connection can be disconnected automatically after a specified inactivity period (Max Idle Time) and not be able to re-establish when you attempt to access the internet again. Note:

Sometimes the connection cannot be terminated although you have specified the Max Idle Time because some applications are visiting the internet continually in the background. LAN 4. 3. 2. 1. Visit http://tplinkwifi.net, and log in with the default username and password: admin. 2. Go to Network > LAN. 3. Configure the IP parameters of the LAN and click Save. 26 Chapter 4 Configure the Router in Standard Wireless Router MAC Address - The physical address of the LAN ports. The value can not be changed. IP Address - Enter the IP address in dotted-decimal notation of your router (factory default - 192.168.0.254). Subnet Mask - An address code that determines the size of the network. Normally 255.255.255.0 is used as the subnet mask. Note:

If you have changed the IP address, you must use the new IP address to log in. If the new IP address you set is not in the same subnet as the old one, the IP address pool in the DHCP Server will be configured automatically, but the Virtual Server and DMZ Host will not take effect until they are re-configured. IPTV 4. 3. 3. 1. Visit http://tplinkwifi.net, and log in with the default username and password: admin. 2. Go to Network > IPTV. IGMP Snooping - IGMP snooping is designed to prevent hosts on a local network from receiving traffic for a multicast group they have not explicitly joined. IGMP snooping is especially useful for bandwidth-intensive IP multicast applications such as IPTV. IGMP Proxy - Select to enable IGMP Proxy. 27 Chapter 4 Configure the Router in Standard Wireless Router IGMP Version - Select the IGMP(Internet Group Management Protocol) Proxy Version, either V2 or V3, according to your ISP. IPTV - Select to enable the IPTV feature. Mode - Select the appropriate mode according to your ISP. LAN 1/2/3/4 - Assign your LAN port to whether function as the Internet supplier or as the IPTV supplier. 4. 3. 4. MAC Clone 1. Visit http://tplinkwifi.net, and log in with the default username and password: admin. 2. Go to Network > MAC Clone. 3. Configure the WAN MAC address and click Save. WAN MAC Address - This field displays the current MAC address of the WAN port. If your ISP requires you to register the MAC address, please enter the correct MAC address in this field. Click Restore Factory MAC to restore the MAC address of WAN port to the factory default value. Your PCs MAC Address - This field displays the MAC address of the PC that is managing the router. If the MAC address is required, you can click Clone MAC Address and this MAC address will be filled in the WAN MAC Address field. Note:

You can only use the MAC Address Clone function for PCs on the LAN. If you have changed the WAN MAC address when the WAN connection is PPPoE, it will not take effect until the connection is re-established. 4. 4. Wireless 4. 4. 1. 1. Visit http://tplinkwifi.net, and log in with the default username and password: admin. 2. Go to Wireless > Basic Settings. 3. Configure the basic settings for the wireless network and click Save. Basic Settings 28 Chapter 4 Configure the Router in Standard Wireless Router Wireless - Enable or disable wireless function as needed. Wireless Network Name - Enter a string of up to 32 characters. The default SSID is TP-Link_XXXX (XXXX indicates the last unique four numbers of each routers MAC address). It is strongly recommended that you change your network name (SSID). This value is case-sensitive. For example, TEST is NOT the same as test. Region - Select your region from the pull-down list. This field specifies the region where the wireless function of the Router can be used. It may be illegal to use the wireless function of the Router in a region other than one of those specified in this filed. If your country or region is not listed, please contact your local government agency for assistance. Mode - Select the desired mode. It is strongly recommended that you keep the default setting 11bgn mixed, so that all 802.11b/g/n wireless devices can connect to the router. Note:

If 11bg mixed mode is selected, the Channel Width field will turn grey and the value will become 20M, and cannot be changed. Channel - This field determines which operating frequency will be used. The default channel is set to Auto. It is not necessary to change the wireless channel unless you notice interference problems with another nearby access point. Channel Width - Select any channel width from the drop-down list. The default setting is Auto, which can automatically adjust the channel width for your clients. Enable SSID Broadcast - If enabled, the router will broadcast the wireless network name (SSID). 29 Chapter 4 Configure the Router in Standard Wireless Router 4. 4. 2. WPS WPS (Wi-Fi Protected Setup) can help you to quickly and securely connect to a wireless network. This section will guide you to add a new wireless device to your routers network via WPS. Note:

The WPS function cannot be preformed if the wireless function of the router is disabled. Please make sure the wireless function is enabled before configuration. 1. Visit http://tplinkwifi.net, and log in with the default username and password: admin. 2. Go to WPS. 3. Follow one of the following three methods to connect your client device to the routers Wi-Fi network. Method ONE: Press the WPS Button on Your Client Device 1. Keep the WPS Status as Enabled and click Add Device. 2. Select Press the WPS button of the new device in two minutes and click Connect. 3. Within two minutes, press the WPS button on your client device. 4. A success message will appear on the WPS page if the client device has been successfully added to the routers network. Method TWO: Enter the Clients PIN 1. Keep the WPS Status as Enabled and click Add Device. 30 Chapter 4 Configure the Router in Standard Wireless Router 2. Select Enter the new devices PIN, enter your client devices current PIN in the PIN filed and click Connect. 3. A success message will appear on the WPS page if the client device has been successfully added to the routers network. Method Three: Enter the Routers PIN 1. Keep the WPS Status as Enabled and get the Current PIN of the router. 2. Enter the routers current PIN on your client device to join the routers Wi-Fi network. 4. 4. 3. Wireless Security 1. Visit http://tplinkwifi.net, and log in with the default username and password: admin. 2. Go to Wireless > Wireless Security. 3. Configure the security settings of your wireless network and click Save. 31 Chapter 4 Configure the Router in Standard Wireless Router Disable Security - The wireless security function can be enabled or disabled. If disabled, wireless clients can connect to the router without a password. Its strongly recommended to choose one of the following modes to enable security. WPA-PSK/WPA2-Personal - Its the WPA/WPA2 authentication type based on pre-

shared passphrase. Encryption - Select Automatic, TKIP or AES. Version - Select Automatic, WPA-PSK or WPA2-PSK. Wireless Password - Enter ASCII or Hexadecimal characters. For Hexadecimal, the length should be between 8 and 64 characters; for ASCII, the length should be between 8 and 63 characters. Group Key Update Period - Specify the group key update interval in seconds. The value can be 0 or at least 30. Enter 0 to disable the update. WPA /WPA2-Enterprise - Its based on Radius Server. Version - Select Automatic, WPA or WPA2. Encryption - Select Automatic, TKIP or AES. Radius Server IP - Enter the IP address of the Radius server. Radius Port - Enter the port that Radius server used. Radius Password - Enter the password for the Radius server. 32 Chapter 4 Configure the Router in Standard Wireless Router Group Key Update Period - Specify the group key update interval in seconds. The value should be 30 or above. Enter 0 to disable the update. WEP - It is based on the IEEE 802.11 standard. Type - The default setting is Automatic, which can select Shared Key or Open System authentication type automatically based on the wireless clients capability and request. WEP Key Format - Hexadecimal and ASCII formats are provided here. Hexadecimal format stands for any combination of hexadecimal digits (0-9, a-f, A-F) in the specified length. ASCII format stands for any combination of keyboard characters in the specified length. WEP Key (Password) - Select which of the four keys will be used and enter the matching WEP key. Make sure these values are identical on all wireless clients in your network. Key Type - Select the WEP key length (64-bit, 128-bit or 152-bit) for encryption. Disabled means this WEP key entry is invalid. 64-bit - Enter 10 hexadecimal digits (any combination of 0-9, a-f and A-F. Null key is not permitted) or 5 ASCII characters. 128-bit - Enter 26 hexadecimal digits (any combination of 0-9, a-f and A-F. Null key is not permitted) or 13 ASCII characters. 152-bit - Enter 32 hexadecimal digits (any combination of 0-9, a-f and A-F. Null key is not permitted) or 16 ASCII characters. 4. 4. 4. Wireless MAC Filtering Wireless MAC Filtering is used to deny or allow specific wireless client devices to access your network by their MAC addresses. I want to:

Deny or allow specific wireless client devices to access my network by their MAC addresses. For example, you want the wireless client A with the MAC address 00-0A-EB-B0-00-0B and the wireless client B with the MAC address 00-0A-EB-00-07-5F to access the router, but other wireless clients cannot access the router. 1. Visit http://tplinkwifi.net, and log in with the default username and password: admin. 2. Go to Wireless > Wireless MAC Filtering. 3. Click Enable to enable the Wireless MAC Filtering function. 33 How can I do that?

Chapter 4 Configure the Router in Standard Wireless Router 4. Select Allow the stations specified by any enabled entries in the list to access as the filtering rule. 5. Delete or disable all entries if there are any entries already. 6. Click Add New and fill in the blanks. 00-07-5F in the MAC Address field. 1 ) Enter the MAC address 00-0A-EB-B0-00-0B/00-0A-EB-

2 ) Enter wireless client A/B in the Description field. 3 ) Leave the status as Enabled. 4 ) Click Save and click Back. 7. The configured filtering rules should be listed as the picture shows below. Done!

Now only client A and client B can access your network. 4. 4. 5. Wireless Advanced 1. Visit http://tplinkwifi.net, and log in with the default username and password: admin. 2. Go to Wireless > Wireless Advanced. 3. Configure the advanced settings of your wireless network and click Save. Note:

If you are not familiar with the setting items on this page, its strongly recommended to keep the provided default values;

otherwise it may result in lower wireless network performance. 34 Chapter 4 Configure the Router in Standard Wireless Router Transmit Power - Select High, Middle or Low which you would like to specify for the router. High is the default setting and recommended. Beacon Interval - Enter a value between 40-1000 milliseconds for Beacon Interval here. Beacon Interval value determines the time interval of the beacons. The beacons are the packets sent by the router to synchronize a wireless network. The default value is 100. RTS Threshold - Here you can specify the RTS (Request to Send) Threshold. If the packet is larger than the specified RTS Threshold size, the router will send RTS frames to a particular receiving station and negotiate the sending of a data frame. The default value is 2346. Fragmentation Threshold - This value is the maximum size determining whether packets will be fragmented. Setting a low value for the Fragmentation Threshold may result in poor network performance because of excessive packets. 2346 is the default setting and is recommended. DTIM Interval - This value determines the interval of the Delivery Traffic Indication Message (DTIM). A DTIM field is a countdown field informing clients of the next window for listening to broadcast and multicast messages. When the router has buffered broadcast or multicast messages for associated clients, it sends the next DTIM with a DTIM Interval value. You can specify the value between 1-255 Beacon Intervals. The default value is 1, which indicates the DTIM Interval is the same as Beacon Interval. Enable Short GI - It is recommended to enable this function, for it will increase the data capacity by reducing the guard interval time. Enable Client Isolation - This function isolates all connected wireless stations so that wireless stations cannot access each other through WLAN. This function will be disabled if WDS / Bridge is enabled. Enable WMM - WMM function can guarantee the packets with high-priority messages being transmitted preferentially. It is strongly recommended to enable this function. 35 Chapter 4 Configure the Router in Standard Wireless Router 4. 4. 6. Wireless Statistics 1. Visit http://tplinkwifi.net, and log in with the default username and password: admin. 2. Go to Wireless > Wireless Statistics to check the data packets sent and received by each client device connected to the router. MAC Address - The MAC address of the connected wireless client. Current Status - The running status of the connected wireless client. Received Packets - Packets received by the wireless client. Sent Packets - Packets sent by the wireless client. Configure - The button is used for loading the item to the Wireless MAC Filtering list. Allow - If the Wireless MAC Filtering function is enabled, click this button to allow the client to access your network. Deny - If the Wireless MAC Filtering function is enabled, click this button to deny the client to access your network. 4. 5. Guest Network Guest Network allows you to provide Wi-Fi access for guests without disclosing your host network. When you have guests in your house, apartment, or workplace, you can create a guest network for them. In addition, you can customize guest network settings to ensure network security and privacy. 1. Visit http://tplinkwifi.net, and log in with the default username and password: admin. 2. Go to Guest Network. 3. Enable the Guset Network function. 4. Create a network name for your guest network. 5. Select the Security type and create the Password of the guest network. 6. Select Schedule from the Access Time drop-down list and customize it for the guest network. 7. Click Save. 36 Chapter 4 Configure the Router in Standard Wireless Router Allow Guest To Access My Local Network - If enabled, guests can access the local network and manage it. Guest Network Isolation - If enabled, guests are isolated from each other. Enable Guest Network Bandwidth Control - If enabled, the Guest Network Bandwidth Control rules will take effect. Note: The range of bandwidth for guest network is calculated according to the setting of Bandwidth Control on the Bandwidth Control > Control Settings page. 4. 6. DHCP By default, the DHCP (Dynamic Host Configuration Protocol) Server is enabled and the router acts as a DHCP server; it dynamically assigns TCP/IP parameters to client devices from the IP Address Pool. You can change the settings of DHCP Server if necessary, and you can reserve LAN IP addresses for specified client devices. 4. 6. 1. DHCP Settings 1. Visit http://tplinkwifi.net, and log in with the default username and password: admin. 2. Go to DHCP > DHCP Settings. 37 Chapter 4 Configure the Router in Standard Wireless Router 3. Specify DHCP server settings and click Save. DHCP Server - Enable or disable the DHCP server. If disabled, you must have another DHCP server within your network or else you must configure the computer manually. Start IP Address - Specify an IP address for the DHCP Server to start with when assigning IP addresses. 192.168.0.100 is the default start address. End IP Address - Specify an IP address for the DHCP Server to end with when assigning IP addresses. 192.168.0.199 is the default end address. Address Lease Time - The Address Lease Time is the amount of time a network user will be allowed to connect to the router with the current dynamic IP Address. When time is up, the user will be automatically assigned a new dynamic IP address. The range of the time is 1 ~ 2880 minutes. The default value is 120. Default Gateway (Optional) - It is suggested to input the IP address of the LAN port of the router. The default value is 192.168.0.1. Default Domain (Optional) - Input the domain name of your network. DNS Server (Optional) - Input the DNS IP address provided by your ISP. Secondary DNS Server (Optional) - Input the IP address of another DNS server if your ISP provides two DNS servers. Note:

To use the DHCP server function of the router, you must configure all computers on the LAN as Obtain an IP Address automatically. When you choose Smart IP (DHCP) in Network > LAN, the DHCP Server function will be disabled. You will see the page as below. 38 Chapter 4 Configure the Router in Standard Wireless Router 4. 6. 2. DHCP Client List 1. Visit http://tplinkwifi.net, and log in with the default username and password: admin. 2. Go to DHCP > DHCP Client List to view the information of the clients connected to the router. Client Name - The name of the DHCP client. MAC Address - The MAC address of the DHCP client. Assigned IP - The IP address that the outer has allocated to the DHCP client. Lease Time - The time of the DHCP client leased. After the dynamic IP address has expired, a new dynamic IP address will be automatically assigned to the user. You cannot change any of the values on this page. To update this page and show the current attached devices, click Refresh. 4. 6. 3. Address Reservation You can reserve an IP address for a specific client. When you specify a reserved IP address for a PC on the LAN, this PC will always receive the same IP address each time when it accesses the DHCP server. 1. Visit http://tplinkwifi.net, and log in with the default username and password: admin. 2. Go to DHCP > Address Reservation. 3. Click Add New and fill in the blank. 39 Chapter 4 Configure the Router in Standard Wireless Router 1 ) Enter the MAC address (in XX-XX-XX-XX-XX-XX format.) of the client for which you want to reserve an IP address. 2 ) Enter the IP address (in dotted-decimal notation) which you want to reserve for the client. 3 ) Leave the Status as Enabled. 4 ) Click Save. Forwarding 4. 7. The routers NAT (Network Address Translation) feature makes the devices on the LAN use the same public IP address to communicate in the internet, which protects the local network by hiding IP addresses of the devices. However, it also brings about the problem that external hosts cannot initiatively communicate with the specified devices in the local network. With the forwarding feature, the router can traverse the isolation of NAT so that clients on the internet can reach devices on the LAN and realize some specific functions. The TP-Link router includes four forwarding rules. If two or more rules are set, the priority of implementation from high to low is Virtual Servers, Port Triggering, UPNP and DMZ. 4. 7. 1. Virtual Server When you build up a server in the local network and want to share it on the internet, Virtual Servers can realize the service and provide it to internet users. At the same time virtual servers can keep the local network safe as other services are still invisible from the internet. Virtual Servers can be used to set up public services in your local network, such as HTTP, FTP, DNS, POP3/SMTP and Telnet. Different service uses different service port. Port 80 is used in HTTP service, port 21 in FTP service, port 25 in SMTP service and port 110 in POP3 service. Please verify the service port number before the configuration. I want to:

Share my personal website Ive built in local network with my friends through the internet. 40 Chapter 4 Configure the Router in Standard Wireless Router For example, the personal website has been built in my home PC

(192.168.0.100). I hope that my friends on the internet can visit my website in some way. My PC is connected to the router with the WAN IP address 218.18.232.154. Personal Website Router LAN WAN: 218.18.232.154 Home 1. Set your PC to a static IP address, for example 192.168.0.100. 2. Visit http://tplinkwifi.net, and log in with the default username and password: admin. 3. Go to Forwarding > Virtual Server. 4. Click Add New. Select HTTP from the Common Service Port internal port and protocol will be automatically filled in. Enter the PCs IP address 192.168.0.100 in the IP Address field. list. The service port, Done!

5. Leave the status as Enabled and click Save. Note:

It is recommended to keep the default settings of Internal Port and Protocol if you are not clear about which port and protocol to use. If the service you want to use is not in the Common Service Port list, you can enter the corresponding parameters manually. You should verify the port number that the service needs. You can add multiple virtual server rules if you want to provide several services in a router. Please note that the Service Port should not be overlapped. Users on the internet can enter http:// WAN IP (in this example:

http:// 218.18.232.154) to visit your personal website. Note:

If you have changed the default Service Port, you should use http:// WAN IP: Service Port to visit the website. Some specific service ports are forbidden by the ISP, if you fail to visit the website, please use another service port. 41 Chapter 4 Configure the Router in Standard Wireless Router Port Triggering 4. 7. 2. Port triggering can specify a triggering port and its corresponding external ports. When a host in the local network initiates a connection to the triggering port, all the external ports will be opened for subsequent connections. The router can record the IP address of the host. When the data from the internet return to the external ports, the router can forward them to the corresponding host. Port triggering is mainly applied to online games, VoIPs, video players and common applications including MSN Gaming Zone, Dialpad, Quick Time 4 players and more. Follow the steps below to configure the port triggering rules:

1. Visit http://tplinkwifi.net, and log in with the default username and password: admin. 2. Go to Forwarding > Port Triggering. 3. Click Add New. Select the desired application from the Common Applications list. The trigger port amd incoming ports will be automatically filled in. The following picture takes application MSN Gaming Zone as an example. 4. Leave the status as Enabled and click Save. Note:

You can add multiple port triggering rules as needed. The triggering ports can not be overlapped. If the application you need is not listed in the Common Applications list, please enter the parameters manually. You should verify the incoming ports the application uses first and enter them in Open Port field. You can input at most 5 groups of ports (or port sections). Every group of ports must be set apart with ,. For example, 2000-2038, 2050-2051, 2085, 3010-3030. 4. 7. 3. DMZ When a PC is set to be a DMZ (Demilitarized Zone) host in the local network, it is totally exposed to the Internet, which can realize the unlimited bidirectional communication between internal hosts and external hosts. The DMZ host becomes a virtual server with all ports opened. When you are not clear about which ports to open in some special applications, such as IP camera and database software, you can set the PC to be a DMZ host. 42 Chapter 4 Configure the Router in Standard Wireless Router Note:

DMZ is more applicable in the situation that users are not clear about which ports to open. When it is enabled, the DMZ host is totally exposed to the internet, which may bring some potential safety hazards. If DMZ is not in use, please disable it in time. I want to:

Make the home PC join the internet online game without port restriction. For example, due to some port restriction, when playing the online games, you can log in normally but cannot join a team with other players. To solve this problem, set your PC as a DMZ host with all ports opened. 1. Assign a static IP address to your PC, for example 192.168.0.100. and password: admin. 2. Visit http://tplinkwifi.net, and log in with the default username 3. Go to Forwarding > DMZ. 4. Select Enable and enter the IP address 192.168.0.100 in the DMZ Host IP Address filed. How can I do that?

Done!

5. Click Save. Youve set your PC to a DMZ host and now you can make a team to game with other players. 4. 7. 4. UPnP The UPnP (Universal Plug and Play) protocol allows the applications or host devices to automatically find the front-end NAT device and send request to it to open the corresponding ports. With UPnP enabled, the applications or host devices on the local network and the internet can freely communicate with each other realizing the seamless connection of the network. You may need to enable the UPnP if you want to use applications for multiplayer gaming, peer-to-peer connections, real-time communication (such as VoIP or telephone conference) or remote assistance, etc. Tips:

UPnP is enabled by default in this router. Only the application supporting UPnP protocol can use this feature. UPnP feature needs the support of operating system (e.g. Windows Vista/ Windows 7/ Windows 8, etc. Some of operating system need to install the UPnP components). 43 Chapter 4 Configure the Router in Standard Wireless Router For example, when you connect your Xbox to the router which is connected to the internet to play online games, UPnP will send request to the router to open the corresponding ports allowing the following data penetrating the NAT to transmit. Therefore, you can play Xbox online games without a hitch. LAN WAN Xbox Router If necessary, you can follow the steps to change the status of UPnP. 1. Visit http://tplinkwifi.net, and log in with the default username and password: admin. 2. Go to Forwarding > UPnP. 3. Click Disable or Enable according to your needs. 4. 8. Security This function allows you to protect your home network from cyber attacks and unauthorized users by implementing these network security functions. 4. 8. 1. 1. Visit http://tplinkwifi.net, and log in with the default username and password: admin. 2. Go to Security > Basic Security, and you can enable or disable the security functions. Basic Security 44 Chapter 4 Configure the Router in Standard Wireless Router Firewall - A firewall protects your network from internet attacks. SPI Firewall - SPI (Stateful Packet Inspection, also known as dynamic packet filtering) helps to prevent cyber attacks by tracking more state per session. It validates that the traffic passing through the session conforms to the protocol. SPI Firewall is enabled by default. VPN - VPN Passthrough must be enabled if you want to allow VPN tunnels using IPSec, PPTP or L2TP protocols to pass through the routers firewall. PPTP Passthrough - Point-to-Point Tunneling Protocol (PPTP) allows the Point-

to-Point Protocol (PPP) to be tunneled through an IP network. If you want to allow PPTP tunnels to pass through the router, you can keep the default (Enabled). L2TP Passthrough - Layer 2 Tunneling Protocol (L2TP) is the method used to enable Point-to-Point sessions via the internet on the Layer 2 level. If you want to allow L2TP tunnels to pass through the router, you can keep the default

(Enabled). IPSec Passthrough - Internet Protocol Security (IPSec) is a suite of protocols for ensuring private, secure communications over Internet Protocol (IP) networks, through the use of cryptographic security services. If you want to allow IPSec tunnels to pass through the router, you can keep the default (Enabled). ALG - It is recommended to enable Application Layer Gateway (ALG) because ALG allows customized Network Address Translation (NAT) traversal filters to be plugged into the gateway to support address and port translation for certain application layer control/data protocols such as FTP, TFTP, H323 etc. 45 Chapter 4 Configure the Router in Standard Wireless Router FTP ALG - To allow FTP clients and servers to transfer data across NAT, keep the default Enable. TFTP ALG - To allow TFTP clients and servers to transfer data across NAT, keep the default Enable. H323 ALG - To allow Microsoft NetMeeting clients to communicate across NAT, keep the default Enable. RTSP ALG - To allow some media player clients to communicate with some streaming media servers across NAT, click Enable. SIP ALG - To allow some multimedia clients to communicate across NAT, click Enable. 3. Click Save. 4. 8. 2. Advanced Security 1. Visit http://tplinkwifi.net, and log in with the default username and password: admin. 2. Go to Security > Advanced Security, and you can protect the router from being attacked by ICMP-Flood, UDP Flood and TCP-SYN Flood. DoS Protection - Denial of Service protection. Select Enable or Disable to enable or disable the DoS protection function. Only when it is enabled, will the flood filters be enabled. Note:

Dos Protection will take effect only when the Statistics in System Tool > Statistics is enabled. Enable ICMP-FLOOD Attack Filtering -Check the box to enable or disable this function. ICMP-FLOOD Packets Threshold (5~3600) - The default value is 50. Enter a value between 5 ~ 3600. When the number of the current ICMP-FLOOD packets is beyond the set value, the router will startup the blocking function immediately. 46 Chapter 4 Configure the Router in Standard Wireless Router Enable UDP-FLOOD Filtering - Check the box to enable or disable this function. UDP-FLOOD Packets Threshold (5~3600) - The default value is 500. Enter a value between 5 ~ 3600. When the number of the current UPD-FLOOD packets is beyond the set value, the router will startup the blocking function immediately. Enable TCP-SYN-FLOOD Attack Filtering -Check the box to enable or disable this function. TCP-SYN-FLOOD Packets Threshold (5~3600) - The default value is 50. Enter a value between 5 ~ 3600. When the number of the current TCP-SYN-FLOOD packets is beyond the set value, the router will startup the blocking function immediately. Forbid Ping Packet From WAN Port - The default setting is enable. If disabled, the ping packet from the internet can access the router. Forbid Ping Packet From LAN Port - The default setting is disabled. If enabled, the ping packet from LAN cannot access the router. This function can be used to defend against some viruses. 3. Click Save. 4. Click Blocked DoS Host List to display the DoS host table by blocking. 4. 8. 3. 1. Visit http://tplinkwifi.net, and log in with the default username and password: admin. 2. Go to Security > Local Management, and you can block computers in LAN from Local Management accessing the router. For example, if you want to allow PCs with specific MAC addresses to access the routers web management page locally from inside the network, please follow the instructions below:

1 ) Select Only the PCs listed can browse the built-in web pages to perform Administrator tasks. 2 ) Enter the MAC address of each PC separately. The format of the MAC address is XX-XX-XX-XX-XX-XX (X is any hexadecimal digit). Only the PCs with the listed 47 Chapter 4 Configure the Router in Standard Wireless Router MAC addresses can use the password to browse the built-in web pages to perform administrator tasks. 3 ) Click Add, and your PCs MAC address will also be listed. 4 ) Click Save. Tips:

If your PC is blocked but you want to access the router again, press and hold the Reset button to reset the router to the factory defaults. Remote Management 4. 8. 4. 1. Visit http://tplinkwifi.net, and log in with the default username and password: admin. 2. Go to Security > Remote Management, and you can manage your router from a remote device via the internet. Web Management Port - Web browser access normally uses the standard HTTP service port 80. This routers default remote management web port number is 80. For higher security, you can change the remote management web port to a custom port by entering a number between 1 and 65534 but do not use the number of any common service port. Remote Management IP Address - This is the address you will use when accessing your router via a remote device. This function is disabled when the IP address is set to the default value of 0.0.0.0. To enable this function, change 0.0.0.0 to a valid IP address. If it is set to 255.255.255.255, then all the remote devices can access the router from the internet. Tips:

To access the router, enter your routers WAN IP address in your browsers address bar, followed by a colon and the custom port number. For example, if your routers WAN address is 202.96.12.8, and the port number used is 8080, please enter http://202.96.12.8:8080 in your browser. Later, you may be asked for the routers password. After successfully entering the username and password, you will be able to access the routers web management page. Be sure to change the routers default password for security purposes. 4. 9. Parental Controls Parental Controls allows you to block inappropriate and malicious websites, and control access to specific websites at specific time for your childrens devices. 48 Chapter 4 Configure the Router in Standard Wireless Router For example, you want the childrens PC with the MAC address 00-11-22-33-44-AA can access www.tp-link.com on Saturday only while the parent PC with the MAC address 00-11-22-33-44-BB is without any restriction. 1. Visit http://tplinkwifi.net, and log in with the default username and password: admin. 2. Go to Parental Controls. 3. Check the Enable Parental Controls box and enter the MAC address 00:11:22:33:44:BB in the MAC Address of Parental PC field. 4. Enter 00:11:22:33:44:AA in the MAC Address 1 field. 5. Create a new schedule with Day is Sat and Time is all day-24 hours. Click Add 6. Enter www.tp-link.com in the Add URL field. Click Add. 7. Click Save. Then you will see the page as shown in figure below. 4. 10. Access Control Access Control is used to deny or allow specific client devices to access your network with access time and content restrictions. I want to:

Deny or allow specific client devices to access my network with access tiem and content restrictions. For example, If you want to restrict the internet activities of host 49 Chapter 4 How can I do that?

Configure the Router in Standard Wireless Router with MAC address 00-11-22-33-44-AA on the LAN to access www.tp-link.com only, please follow the steps below:

1. Visit http://tplinkwifi.net, and log in with the default username and password: admin. 2. Go to Access Control > Host and configure the host settings:

1 ) Click Add New. 2 ) Select MAC Address as the mode type. Create a unique description (e.g. host_1) for the host in the Description field and enter 00-11-22-33-44-AA in the MAC Address filed. 3 ) Click Save. 3. Go to Access Control > Target and configure the target settings:

1 ) Click Add New. 2 ) Select URL Address as the mode type. Create a unique description (e.g. target_1) for the target in the Target Description field and enter the domain name, either the full name or the keywords (for example TP-Link) in the Add URL Address field. Note:

Any URL address with keywords in it (e.g. www.tp-link.com) will be blocked or allowed. 3 ) Click Save. 50 Chapter 4 Configure the Router in Standard Wireless Router 4. Go to Access Control > Schedule and configure the schedule settings:

1 ) Click Add New. 2 ) Create a unique description (e.g. schedule_1) for the schedule in the Schedule Description field and set the day(s) and time period. 3 ) Click Save. 5. Go to Access Control > Rule and add a new access control rule. 1 ) Click Add New. 2 ) Give a name for the rule in the Description field. Select host_1 from the LAN host drop-down list; select target_1 from the target drop-down list; select schedule_1 from the schedule drop-down list. 51 Chapter 4 Configure the Router in Standard Wireless Router 3 ) Leave the status as Enabled as click Save. 6. Select Enable Internet Access Control to enable Access Control function. 7. Select Allow the packets specified by any enabled access control policy to pass through the Router as the default filter policy and click Save. Done!

Now only the specific host(s) can visit the target(s) within the scheduled time period. 4. 11. Advanced Routing Static Routing is a form of routing that is configured manually by a network administrator or a user by adding entries into a routing table. The manually-configured routing information guides the router in forwarding data packets to the specific destination. 4. 11. 1. Static Route List 1. Visit http://tplinkwifi.net, and log in with the default username and password: admin. 2. Go to Advanced Routing > Static Route List. 52 Chapter 4 Configure the Router in Standard Wireless Router To add static routing entries:

1. Click Add New. 2. Enter the following information. Destination IP Address - The Destination Network is the address of the network or host that you want to assign to a static route. Subnet Mask - The Subnet Mask determines which portion of an IP address is the network portion, and which portion is the host portion. Gateway - This is the IP address of the default gateway device that allows the contact between the router and the network or host. 3. Select Enabled or Disabled for this entry on the Status drop-down list. 4. Click Save. You can also do the following operations to modify the current settings. Click Delete to delete the entry. Click Enable All to enable all the entries. Click Disable All to disable all the entries. Click Delete All to delete all the entries. Click Previous to view the information on the previous screen and Next to view the information on the next screen. 4. 11. 2. System Routing Table 1. Visit http://tplinkwifi.net, and log in with the default username and password: admin. 2. Go to Advanced Routing > System Routing Table, and you can view all the valid route entries in use. 53 Chapter 4 Configure the Router in Standard Wireless Router Destination Network - The Destination Network is the address of the network or host to which the static route is assigned. Subnet Mask - The Subnet Mask determines which portion of an IP address is the network portion, and which portion is the host portion. Gateway - This is the IP address of the gateway device that allows for contact between the Router and the network or host. Interface - This interface tells you whether the Destination IP Address is on the LAN &

WLAN (internal wired and wireless networks), or the WAN (Internet). Click Refresh to refresh the data displayed. 4. 12. Bandwidth Control 4. 12. 1. Control Settings 1. Visit http://tplinkwifi.net, and log in with the default username and password: admin. 2. Go to Bandwidth Control. 3. Configure the bandwidth as needed and click Save. The values you configure for the Egress Bandwidth and Ingress Bandwidth should be less than 100,000Kbps. For optimal control of the bandwidth, please select the right Line Type and consult your ISP for the total egress and ingress bandwidth. Enable Bandwidth Control - Check this box so that the Bandwidth Control settings can take effect. Egress Bandwidth - The upload speed through the WAN port. Ingress Bandwidth - The download speed through the WAN port. 4. 12. 2. Rule List 1. Visit http://tplinkwifi.net, and log in with the default username and password: admin. 2. Go to Bandwidth Control and you can view and configure the Bandwidth Control rules. 54 Chapter 4 Configure the Router in Standard Wireless Router Description - This is the information about the rules such as address range. Egress Bandwidth - This field displays the max and min upload bandwidth through the WAN port. The default is 0. Ingress Bandwidth - This field displays the max and min download bandwidth through the WAN port. The default is 0. Status - This field displays the status of the rule. Modify - Click Modify/Delete to edit/delete the rule. To add a Bandwidth control rule:

1. Click Add New. 2. Enter the information as the figure shown below. IP&MAC Binding 3. Click Save. 4. 13. IP & MAC Binding, namely, ARP (Address Resolution Protocol) Binding, is used to bind a network devices IP address to its MAC address. This will prevent ARP spoofing and other ARP attacks by denying network access to a device with a matching IP address in the ARP list, but with an unrecognized MAC address. 4. 13. 1. Binding Settings 1. Visit http://tplinkwifi.net, and log in with the default username and password: admin. 2. Go to IP & MAC Binding > Binding Settings. 3. Select Enable for ARP Binding. 55 Chapter 4 Configure the Router in Standard Wireless Router 4. Click Save. To add IP & MAC Binding entries:

1. Click Add New. 2. Select the Bind checkbox. 3. Enter the MAC address and IP address. 4. Click Save. To modify or delete an existing entry:

1. Select the desired entry in the table. 2. Click Edit or Delete Selected. 4. 13. 2. ARP List To manage a device, you can observe the device on the LAN by checking its MAC address and IP address on the ARP list, and you can also configure the items. This page displays the ARP list which shows all the existing IP & MAC Binding entries. MAC Address - The MAC address of the listed computer on the LAN. IP Address - The assigned IP address of the listed computer on the LAN. Status - Indicates whether or not the MAC and IP addresses are bound. Configure - Load or delete an item. Load - Load the item to the IP & MAC Binding list. Delete - Delete the item. 56 Chapter 4 Configure the Router in Standard Wireless Router Click the Load Selected button to load the selected items to the IP & MAC Binding list. Click the Delete Selected button to delete the selected items to the IP & MAC Binding list. Click the Refresh button to refresh all items. Note:

An item can not be loaded to the IP & MAC Binding list if the IP address of the item has been loaded before. Error warning will prompt as well. Likewise, Load All only loads the items without interference to the IP & MAC Binding list. 4. 14. Dynamic DNS The router offers the DDNS (Dynamic Domain Name System) feature, which allows the hosting of a website, FTP server, or e-mail server with a fixed domain name (named by yourself) and a dynamic IP address. Thus your friends can connect to your server by entering your domain name no matter what your IP address is. Before using this feature, you need to sign up for DDNS service providers such as www.comexe.cn, www.dyndns.org, or www.noip.com. The Dynamic DNS client service provider will give you a password or key. 1. Visit http://tplinkwifi.net, and log in with the default username and password: admin. 2. Go to Dynamic DNS. Dyndns DDNS If the dynamic DNS Service Provider you select is www.dyn.com, the following page will appear. To set up for DDNS, follow these instructions:

1. Enter the Domain Name you received from dynamic DNS service provider here. 2. Enter the User Name for your DDNS account. 3. Enter the Password for your DDNS account. 4. Click Login. 57 Chapter 4 Configure the Router in Standard Wireless Router 5. Click Save. Connection Status - The status of the DDNS service connection is displayed here. Logout - Click Logout to log out of the DDNS service. No-ip DDNS If the dynamic DNS Service Provider you select is www.noip.com, the following page will appear. To set up for DDNS, follow these instructions:

1. Enter the Domain Name you received from dynamic DNS service provider. 2. Enter the User Name for your DDNS account. 3. Enter the Password for your DDNS account. 4. Click Login. 5. Click Save. Connection Status - The status of the DDNS service connection is displayed here. Logout - Click Logout to log out of the DDNS service. Comexe DDNS If the dynamic DNS Service Provider you select is www.comexe.cn, the following page will appear. 58 Chapter 4 Configure the Router in Standard Wireless Router To set up for DDNS, follow these instructions:

1. Enter the Domain Name received from your dynamic DNS service provider. 2. Enter the User Name for your DDNS account. 3. Enter the Password for your DDNS account. 4. Click Login. 5. Click Save. Connection Status - The status of the DDNS service connection is displayed here. Logout - Click Logout to log out of the DDNS service. 4. 15. This function allows you to enable IPv6 function and set up the parameters of the routers Wide Area Network (WAN) and Local Area Network (LAN). 4. 15. 1. 1. Visit http://tplinkwifi.net, and log in with the default username and password: admin. 2. Go to IPv6 > IPv6 Status, and you can view the current IPv6 status information of IPv6 Status IPv6 the router. 59 Chapter 4 Configure the Router in Standard Wireless Router WAN - This section shows the current IPv6 information of the routers WAN port, including Connection Type, IPv6 Address information, IPv6 Default Gateway, Primary IPv6 DNS and Secondary IPv6 DNS. LAN - This section shows the current IPv6 information of the routers LAN port, including IPv6 Address Assign Type, IPv6 Address and Link-local Address. 4. 15. 2. 1. Visit http://tplinkwifi.net, and log in with the default username and password: admin. 2. Go to IPv6 > IPv6 WAN. IPv6 WAN 3. Select the WAN Connection Type according to your ISP network topolopy:

Dynamic IPv6 - Connections which use dynamic IPv6 address assignment. Static IPv6 - Connections which use static IPv6 address assignment. PPPoEv6 - Connections which use PPPoEV6 that requires a username and 60 password. Chapter 4 Configure the Router in Standard Wireless Router Tunnel 6to4 - Connections which use 6to4 address assignment. Dynamic IPv6 IPv6 Gateway - Enter the default gateway provided by your ISP. IPv6 Address - The IPv6 address assigned by your ISP dynamically. Prefix Length - The length of IPv6 address prefix. Addressing Type - There are two types of assignation for IPv6 address:

SLAAC (Stateless address auto-configuration) and DHCPv6 (Dynamic Host Configuration Protocol for IPv6) Server. MTU(Bytes) - The normal MTU (Maximum Transmission Unit) value for most Ethernet networks is 1500 Bytes. For some ISPs, you may need to modify the MTU. But this is rarely required, and should not be done unless you are sure it is necessary for your ISP connection. If your ISP gives you one or two DNS IPv6 addresses, select Set IPv6 DNS Server manually and enter the IPv6 DNS Server and Secondary IPv6 DNS Server into the correct fields. Otherwise, the DNS servers will be assigned from ISP dynamically. Enable MLD Proxy - Enable the Multicast Listener Discovery (MLD) Proxy function if you need. IPv6 DNS Server - Enter the DNS IPv6 address provided by your ISP. Secondary IPv6 DNS Server - Enter another DNS IPv6 address provided by your ISP. Tips:

If you get Address not found error when you access a website, it is likely that your DNS servers are set up improperly. You should contact your ISP to get DNS server addresses. 61 Configure the Router in Standard Wireless Router Chapter 4 Static IPv6 IPv6 Address - Enter the IPv6 address provided by your ISP. Prefix Length - The length of IPv6 address prefix. Secondary IPv6 DNS Server - Enter another DNS IPv6 address provided by IPv6 Gateway - Enter the default gateway provided by your ISP. IPv6 DNS Server- Enter the DNS IPv6 address provided by your ISP. your ISP. MTU(Bytes) - The normal MTU (Maximum Transmission Unit) value for most Ethernet networks is 1500 Bytes. For some ISPs, you may need to modify the MTU. But this is rarely required, and should not be done unless you are sure it is necessary for your ISP connection. Enable MLD Proxy - Enable the Multicast Listener Discovery (MLD) Proxy function if you need. PPPoEv6 62 Chapter 4 Configure the Router in Standard Wireless Router PPP Username/Password - Enter the User Name and Password provided by your ISP. These fields are case-sensitive. Authentication Type Choose one authentication type from AUTO-AUTH, PAP, CHAP and MS-CHAP. Addressing Type - There are two types of assignation for IPv6 address:

SLAAC (Stateless address auto-configuration) and DHCPv6 (Dynamic Host Configuration Protocol for IPv6) Server. MTU(Bytes) - The normal MTU (Maximum Transmission Unit) value for most Ethernet networks is 1480 Bytes. It is not recommended that you change the default MTU size unless required by your ISP. Enable MLD Proxy - Enable the Multicast Listener Discovery (MLD) Proxy function if you need. Use IPv6 address specified by ISP - Input a static IPv6 address from the ISP. Set IPv6 DNS Server manually - Enter the IP address of the IPv6 DNS server and secondary IPv6 DNS server. Tunnel 6to4 WAN Connection - Display the available WAN connection. 4. Click Save. 4. 15. 3. 1. Visit http://tplinkwifi.net, and log in with the default username and password: admin. 2. Go to IPv6 > IPv6 LAN. IPv6 LAN 63 Chapter 4 Configure the Router in Standard Wireless Router 3. Select the Address Autoconfiguration Type which determines the way how the router assigns IPv6 address for PCs on the LAN:

Address Autoconfiguration Type - RADAD (Router Advertisement Daemon) and DHCPv6 (Dynamic Host Configuration Protocol for IPv6) Server. Site Prefix Configuration Type - The type of IPv6 address prefix. Delegated - Get the IPv6 address prefix from the ISP automatically, and the device will delegate it to the LAN. Static - Configure the Site Prefix and Site Prefix Length manually. Please contact your ISP to get more information before you configure them. Tips: If your IPv6 wan connection type is Tunnel 6to4, the Site Prefix Configuration Type should be Static to make sure Tunnel 6to4 works properly. 4. Click Save. 4. 16. System Tools 4. 16. 1. LED Control The LED control feature allows you to turn off or on the LEDs of the router automatically when needed. 1. Visit http://tplinkwifi.net, and log in with the default username and password: admin. 2. Go to System Tools > LED Control. 3. Tick Night Mode and select the LED Off Time from the pull-down lists. Then click Save. 64 Chapter 4 Configure the Router in Standard Wireless Router 4. 16. 2. Time Settings This page allows you to set the time manually or to configure automatic time synchronization. The Router can automatically update the time from an NTP server via the internet. 1. Visit http://tplinkwifi.net, and log in with the default username and password: admin. 2. Go to System Tools > Time Settings. To set time manually:

1. Select your local time zone. 2. Enter the Date in Month/Day/Year format. 3. Enter the Time in Hour/Minute/Second format. 4. Click Save. To set time automatically:

5. Select your local time zone. 6. Enter the address or domain of the NTP Server I or NTP Server II. 7. Click Get GMT to get time from the internet if you have connected to the internet. 65 Chapter 4 Configure the Router in Standard Wireless Router To set Daylight Saving Time:

1. Select Enable DaylightSaving. 2. Select the start time from the drop-down list in the Start field. 3. Select the end time from the drop-down list in the End field. 4. Click Save. Note:

This setting will be used for some time-based functions such as firewall. You must specify your time zone once you log in to the router successfully; otherwise, time-based functions will not take effect. 4. 16. 3. Diagnostic Diagnostic is used to test the connectivity between the router and the host or other network devices. 1. Visit http://tplinkwifi.net, and log in with the default username and password: admin. 2. Go to System Tools > Diagnostic. Diagnostic Tool - Select one diagnostic tool. Ping - This diagnostic tool troubleshoots connectivity, reachability, and name resolution to a given host or gateway. Tracerouter - This diagnostic tool tests the performance of a connection. Note:

You can use ping/traceroute to test both numeric IP address or domain name. If pinging/tracerouting the IP address is successful, but pinging/tracerouting the domain name is not, you might have a name resolution problem. In this case, ensure that the domain name you are specifying can be resolved by using Domain Name System (DNS) queries. IP Address/Domain Name - Enter the destination IP address (such as 192.168.0.1) or Domain name (such as www.tp-link.com). 66 Chapter 4 Configure the Router in Standard Wireless Router Pings Count - The number of Ping packets for a Ping connection. Ping Packet Size - The size of Ping packet. Ping Timeout - Set the waiting time for the reply of each Ping packet. If there is no reply in the specified time, the connection is overtime. Traceroute Max TTL - The max number of hops for a Traceroute connection. 3. Click Start to check the connectivity of the internet. 4. The Diagnostic Results page displays the diagnosis result. If the result is similar to the following figure, the connectivity of the internet is fine. Note: Only one user can use this tool at one time. Options Number of Pings, Ping Size and Ping Timeout are used for the Ping function. Option Tracert Hops is used for the Tracert function. 4. 16. 4. Firmware Upgrade TP-Link is dedicated to improving and richening the product features, giving users a better network experience. We will release the latest firmware at TP-Link official website. You can download the latest firmware file from the Support page of our website www.tp-link.com and upgrade the firmware to the latest version. 1. Download the latest firmware file for the router from our website www.tp-link.com. 2. Visit http://tplinkwifi.net, and log in with the default username and password: admin. 3. Go to System Tools > Firmware Upgrade. 4. Click Choose File to locate the downloaded firmware file, and click Upgrade. 67 Chapter 4 Configure the Router in Standard Wireless Router 4. 16. 5. Factory Defaults 1. Visit http://tplinkwifi.net, and log in with the default username and password: admin. 2. Go to System Tools > Factory Defaults. Click Restore to reset all settings to the default values. The default Username: admin The default Password: admin The default IP Address: 192.168.0.1 The default Subnet Mask: 255.255.255.0 4. 16. 6. Backup & Restore The configuration settings are stored as a configuration file in the router. You can backup the configuration file in your computer for future use and restore the router to the previous settings from the backup file when needed. 1. Visit http://tplinkwifi.net, and log in with the default username and password: admin. 2. Go to System Tools > Backup & Restore. To backup configuration settings:

Click Backup to save a copy of the current settings in your local computer. A .bin file of the current settings will be stored in your computer. To restore configuration settings:

1. Click Choose File to locate the backup configuration file stored in your computer, and 2. Wait a few minutes for the restoring and rebooting. Note:

During the restoring process, do not power off or reset the router. click Restore. 68 Chapter 4 Configure the Router in Standard Wireless Router 4. 16. 7. Reboot 1. Visit http://tplinkwifi.net, and log in with the default username and password: admin. 2. Go to System Tools > Reboot, and you can restart your router. Some settings of the router will take effect only after rebooting, including:

Change the LAN IP Address (system will reboot automatically). Change the DHCP Settings. Change the Working Modes. Change the Web Management Port. Upgrade the firmware of the router (system will reboot automatically). Restore the router to its factory defaults (system will reboot automatically). Update the configuration with the file (system will reboot automatically). 4. 16. 8. Password 1. Visit http://tplinkwifi.net, and log in with the default username and password: admin. 2. Go to System Tools > Password, and you can change the factory default username and password of the router. It is strongly recommended that you change the default username and password of the router, for all users that try to access the routers web-based utility or Quick Setup will be prompted for the routers username and password. 69 Chapter 4 Configure the Router in Standard Wireless Router Note:

The new username and password must not exceed 15 characters and not include any spacing. 3. Click Save. 4. 16. 9. Language 1. Visit http://tplinkwifi.net, and log in with the default username and password: admin. 2. Go to System Tools > Language, and you can view the logs of the router. 3. Select the language you prefer from the pull-down list, and then click Save. 4. 16. 10. System Log 1. Visit http://tplinkwifi.net, and log in with the default username and password: admin. 2. Go to System Tools > System Log, and you can view the logs of the router. Loge Type -By selecting the log type, only logs of this type will be shown. Log Level - By selecting the log level, only logs of this level will be shown. Refresh - Refresh the page to show the latest log list. Clear Log - All the logs will be deleted from the router permanently, not just from the page. 4. 17. Log Out Click Logout at the bottom of the main menu, and you will log out of the web page and be directed to the login window. 70 Chapter 5 Configure the Router in Access Point Mode This chapter presents how to configure the various features of the router working as an Access Point. It contains the following sections:

Status Operation Mode Network Wireless DHCP System Tools Log Out Chapter 5 Configure the Router in Access Point Mode 5. 1. Status 1. Visit http://tplinkwifi.net, and log in with the default username and password: admin. 2. Go to Status. You can view the current status information of the router in Access Point Mode. Firmware Version - The version information of the routers firmware. Hardware Version - The version information of the routers hardware. LAN - This field displays the current settings of the LAN, and you can configure them on the Network > LAN page. MAC address - The physical address of the router. Subnet Mask - The subnet mask associated with the LAN IP address. IP address - The LAN IP address of the router. Wireless - This field displays the basic information or status of the wireless function, and you can configure them on the Wireless > Basic Settings page. Operation Mode - The current wireless working mode in use. Wireless Radio - Indicates whether the wireless feature is enabled or disabled. Name(SSID) - The wireless network name of the router. 72 Chapter 5 Configure the Router in Access Point Mode Mode - The current wireless mode which the router works on. Channel - The current wireless channel. Channel Width - The current wireless channel width. MAC Address - The physical address of the router. System Up Time - The length of the time since the router was last powered on or reset. Click Refresh to get the latest status and settings of the router. 5. 2. Operation Mode 1. Visit http://tplinkwifi.net, and log in with the default username and password: admin. 2. Go to Operation Mode. 3. Select Access Point and click Save. 5. 3. Network 5. 3. 1. 1. Visit http://tplinkwifi.net, and log in with the default username and password:admin. 2. Go to Network > LAN. 3. Configure the IP parameters of the LAN and click Save. LAN 73 Chapter 5 Configure the Router in Access Point Mode Type - Either select Smart IP(DHCP) to get IP address from DHCP server, or Static IP to configure IP address manually. MAC Address - The physical address of the LAN ports. The value can not be changed. IP Address - Enter the IP address in dotted-decimal notation if your select Static IP

(factory default - 192.168.0.254). Subnet Mask - An address code that determines the size of the network. Normally 255.255.255.0 is used as the subnet mask. Note:

If you have changed the IP address, you must use the new IP address to log in. If you select Smart IP(DHCP), the DHCP server of the router will not start up. If the new IP address you set is not in the same subnet as the old one, the IP Address pool in the DHCP Server will be configured automatically, but the Virtual Server and DMZ Host will not take effect until they are re-configured. 5. 4. Wireless 5. 4. 1. 1. Visit http://tplinkwifi.net, and log in with the default username and password: admin. 2. Go to Wireless > Basic Settings. 3. Configure the basic settings for the wireless network and click Save. Basic Settings 74 Chapter 5 Configure the Router in Access Point Mode Wireless - Enable or disable wireless function as needed. Wireless Network Name - Enter a string of up to 32 characters. The default SSID is TP-Link_XXXX (XXXX indicates the last unique four numbers of each routers MAC address). It is strongly recommended that you change your network name (SSID). This value is case-sensitive. For example, TEST is NOT the same as test. Region - Select your region from the pull-down list. This field specifies the region where the wireless function of the Router can be used. It may be illegal to use the wireless function of the Router in a region other than one of those specified in this filed. If your country or region is not listed, please contact your local government agency for assistance. Mode - Select the desired mode. It is strongly recommended that you keep the default setting 11bgn mixed, so that all 802.11b/g/n wireless devices can connect to the router. Note:

If 11bg mixed mode is selected, the Channel Width field will turn gray and the value will become 20M and cannot be changed. Channel - This field determines which operating frequency will be used. The default channel is set to Auto. It is not necessary to change the wireless channel unless you notice interference problems with another nearby access point. Channel Width - Select any channel width from the drop-down list. The default setting is Auto, which can automatically adjust the channel width for your clients. Enable SSID Broadcast - If enabled, the router will broadcast the wireless network name (SSID). 75 Chapter 5 Configure the Router in Access Point Mode 5. 4. 2. WPS WPS (Wi-Fi Protected Setup) can help you to quickly and securely connect to a wireless network. This section will guide you to add a new wireless device to your routers network quickly via WPS. Note:

The WPS function cannot be performed if the wireless function of the router is disabled. Please make sure the wireless function is enabled before configuration. 1. Visit http://tplinkwifi.net, and log in with the default username and password:admin. 2. Go to WPS. 3. Follow one of the following three methods to connect your client device to the routers Wi-Fi network. Method ONE: Press the WPS Button on Your Client Device 1. Keep the WPS Status as Enabled and click Add Device. 2. Select Press the WPS button of the new device in two minutes and click Connect. 3. Within two minutes, press the WPS button on your client device. 4. A success message will appear on the WPS page if the client device has been successfully added to the routers network. 76 Chapter 5 Configure the Router in Access Point Mode Method TWO: Enter the Clients PIN 1. Keep the WPS Status as Enabled and click Add Device. 2. Select Enter the new device PIN, enter your client devices current PIN in the PIN filed and click Connect. 3. A success message will appear on the WPS page if the client device has been successfully added to the routers network. Method Three: Enter the Routers PIN 1. Keep the WPS Status as Enabled and get the Current PIN of the router. 2. Enter the routers current PIN on your client device to join the routers Wi-Fi network. 5. 4. 3. Wireless Security 1. Visit http://tplinkwifi.net, and log in with the default username and password:admin. 2. Go to Wireless > Wireless Security. 3. Configure the security settings of your wireless network and click Save. 77 Chapter 5 Configure the Router in Access Point Mode Disable Wireless Security - The wireless security function can be enabled or disabled. If disabled, wireless clients can connect to the router without a password. Its strongly recommended to choose one of the following modes to enable security. WPA-PSK/WPA2-Personal - Its the WPA/WPA2 authentication type based on pre-

shared passphrase. Encryption - Select Automatic, TKIP or AES. Version - Select Automatic, WPA-PSK or WPA2-PSK. Wireless Password - Enter ASCII or Hexadecimal characters. For Hexadecimal, the length should be between 8 and 64 characters; for ASCII, the length should be between 8 and 63 characters. Group Key Update Period - Specify the group key update interval in seconds. The value can be 0 or at least 30. Enter 0 to disable the update. WPA /WPA2-Enterprise - Its based on Radius Server. Version - Select Automatic, WPA or WPA2. Encryption - Select Automatic, TKIP or AES. Radius Server IP - Enter the IP address of the Radius server. Radius Port - Enter the port that Radius server used. Radius Password - Enter the password for the Radius server. 78 Chapter 5 Configure the Router in Access Point Mode Group Key Update Period - Specify the group key update interval in seconds. The value should be 30 or above. Enter 0 to disable the update. WEP - It is based on the IEEE 802.11 standard. Authentication Type - The default setting is Automatic, which can select Shared Key or Open System authentication type automatically based on the wireless clients capability and request. WEP Key Format - Hexadecimal and ASCII formats are provided here. Hexadecimal format stands for any combination of hexadecimal digits (0-9, a-f, A-F) in the specified length. ASCII format stands for any combination of keyboard characters in the specified length. WEP Key (Password) - Select which of the four keys will be used and enter the matching WEP key. Make sure these values are identical on all wireless clients in your network. Key Type - Select the WEP key length (64-bit, 128-bit or 152-bit) for encryption. Disabled means this WEP key entry is invalid. 64-bit - Enter 10 hexadecimal digits (any combination of 0-9, a-f and A-F. Null key is not permitted) or 5 ASCII characters. 128-bit - Enter 26 hexadecimal digits (any combination of 0-9, a-f and A-F. Null key is not permitted) or 13 ASCII characters. 152-bit - Enter 32 hexadecimal digits (any combination of 0-9, a-f and A-F. Null key is not permitted) or 16 ASCII characters. 5. 4. 4. Wireless MAC Filtering Wireless MAC Filtering is used to deny or allow specific wireless client devices to access your network by their MAC addresses. I want to:

Deny or allow specific wireless client devices to access my network by their MAC addresses. For example, you want the wireless client A with the MAC address 00-0A-EB-B0-00-0B and the wireless client B with the MAC address 00-0A-EB-00-07-5F to access the router, but other wireless clients cannot access the router 1. Visit http://tplinkwifi.net, and log in with the default username and password:admin. 2. Go to Wireless > Wireless MAC Filtering. 3. Click Enable to enable the Wireless MAC Filtering function. How can I do that?

79 Chapter 5 Configure the Router in Access Point Mode 4. Select Allow the stations specified by any enabled entries in the list to access as the filtering rule. 5. Delete all or disable all entries if there are any entries already. 6. Click Add New and fill in the blank. 00-07-5F in the MAC Address field. 1 ) Enter the MAC address 00-0A-EB-B0-00-0B/00-0A-EB-

2 ) Enter wireless client A/B in the Description field. 3 ) Select Enabled in the Status drop-down list. 4 ) Click Save and click Back. 7. The configured filtering rules should be listed as the picture shows below. Now only client A and client B can access your network. Done!

5. 4. 5. Wireless Advanced 1. Visit http://tplinkwifi.net, and log in with the default username and password:admin. 2. Go to Wireless > Wireless Advanced. 3. Configure the advanced settings of your wireless network and click Save. Note:

If you are not familiar with the setting items on this page, its strongly recommended to keep the provided default values;

otherwise it may result in lower wireless network performance. 80 Chapter 5 Configure the Router in Access Point Mode Transmit Power - Select High, Middle or Low which you would like to specify for the router. High is the default setting and recommended. Beacon Interval - Enter a value between 40-1000 milliseconds for Beacon Interval here. Beacon Interval value determines the time interval of the beacons. The beacons are the packets sent by the router to synchronize a wireless network. The default value is 100. RTS Threshold - Here you can specify the RTS (Request to Send) Threshold. If the packet is larger than the specified RTS Threshold size, the router will send RTS frames to a particular receiving station and negotiate the sending of a data frame. The default value is 2346. Fragmentation Threshold - This value is the maximum size determining whether packets will be fragmented. Setting a low value for the Fragmentation Threshold may result in poor network performance because of excessive packets. 2346 is the default setting and is recommended. DTIM Interval - This value determines the interval of the Delivery Traffic Indication Message (DTIM). A DTIM field is a countdown field informing clients of the next window for listening to broadcast and multicast messages. When the router has buffered broadcast or multicast messages for associated clients, it sends the next DTIM with a DTIM Interval value. You can specify the value between 1-255 Beacon Intervals. The default value is 1, which indicates the DTIM Interval is the same as Beacon Interval. Enable Short GI - It is recommended to enable this function, for it will increase the data capacity by reducing the guard interval time. Enable Client Isolation - This function isolates all connected wireless stations so that wireless stations cannot access each other through WLAN. This function will be disabled if WDS/Bridge is enabled. Enable WMM - WMM function can guarantee the packets with high-priority messages being transmitted preferentially. It is strongly recommended to enable this function. 5. 4. 6. Wireless Statistics 1. Visit http://tplinkwifi.net, and log in with the default username and password:admin. 81 Chapter 5 Configure the Router in Access Point Mode 2. Go to Wireless > Wireless Statistics to check the data packets sent and received by each client device connected to the router. MAC Address - The MAC address of the connected wireless client. Current Status - The running status of the connected wireless client. Received Packets - Packets received by the wireless client. Sent Packets - Packets sent by the wireless client. Configure - The button is used for loading the item to the Wireless MAC Filtering list. Allow - If the Wireless MAC Filtering function is enabled, click this button to allow the client to access your network. Deny - If the Wireless MAC Filtering function is enabled, click this button to deny the client to access your network. Throughput Monitor 5. 4. 7. 1. Visit http://tplinkwifi.net, and log in with the default username and password:admin. 2. Go to Wireless > Throughput Monitor to view the wireless throughput information. Rate - The unit for the Throughput. 82 Chapter 5 Configure the Router in Access Point Mode Run Time - How long the Throughput Monitor runs. Transmit - Wireless transmit rate information. Receive - Wireless receive rate information. Click Start / Stop to start or stop wireless throughput monitor. 5. 5. DHCP By default, the DHCP (Dynamic Host Configuration Protocol) Server is enabled and the router acts as a DHCP server; it dynamically assigns TCP/IP parameters to client devices from the IP Address Pool. You can change the settings of DHCP Server if necessary, and you can reserve LAN IP addresses for specified client devices. 5. 5. 1. DHCP Settings 1. Visit http://tplinkwifi.net, and log in with the default username and password:admin. 2. Go to DHCP > DHCP Settings. 3. Specify DHCP server settings and click Save. DHCP Server - Enable or disable the DHCP server. If disabled, you must have another DHCP server within your network or else you must configure the computer manually. Start IP Address - Specify an IP address for the DHCP Server to start with when assigning IP addresses. 192.168.0.100 is the default start address. End IP Address - Specify an IP address for the DHCP Server to end with when assigning IP addresses. 192.168.0.199 is the default end address. Address Lease Time - The Address Lease Time is the amount of time a network user will be allowed to connect to the router with the current dynamic IP Address. When time is up, the user will be automatically assigned a new dynamic IP address. The range of the time is 1 ~ 2880 minutes. The default value is 120. Default Gateway (Optional) - It is suggested to input the IP address of the LAN port of the router. The default value is 192.168.0.254. 83 Chapter 5 Configure the Router in Access Point Mode Default Domain (Optional) - Input the domain name of your network. DNS Server (Optional) - Input the DNS IP address provided by your ISP. Secondary DNS Server (Optional) - Input the IP address of another DNS server if your ISP provides two DNS servers. Note:

To use the DHCP server function of the router, you must configure all computers on the LAN as Obtain an IP Address automatically. When you choose Smart IP (DHCP) in Network > LAN, the DHCP Server function will be disabled. You will see the page as below. 5. 5. 2. DHCP Clients List 1. Visit http://tplinkwifi.net, and log in with the default username and password:admin. 2. Go to DHCP > DHCP Clients List to view the information of the clients connected to the router. Client Name - The name of the DHCP client. MAC Address - The MAC address of the DHCP client. Assigned IP - The IP address that the outer has allocated to the DHCP client. Lease Time - The time of the DHCP client leased. After the dynamic IP address has expired, a new dynamic IP address will be automatically assigned to the user. You cannot change any of the values on this page. To update this page and show the current attached devices, click Refresh. 84 Chapter 5 Configure the Router in Access Point Mode 5. 5. 3. Address Reservation You can reserve an IP address for a specific client. When you specify a reserved IP address for a PC on the LAN, this PC will always receive the same IP address each time when it accesses the DHCP server. 1. Visit http://tplinkwifi.net, and log in with the default username and password:admin. 2. Go to DHCP > Address Reservation. 3. Click Add New and fill in the blank. 1 ) Enter the MAC address (in XX-XX-XX-XX-XX-XX format.) of the client for which you want to reserve an IP address. 2 ) Enter the IP address (in dotted-decimal notation) which you want to reserve for the client. 3 ) Leave the Status as Enabled. 4 ) Click Save. LED Control 5. 6. System Tools 5. 6. 1. The LED control feature allows you to turn off or on the LEDs of the router automatically when needed. 1. Visit http://tplinkwifi.net, and log in with the default username and password: admin. 2. Go to System Tools > LED Control. 3. Tick Night Mode and select the LED Off Time from the pull-down lists. Then click Save. 85 Chapter 5 Configure the Router in Access Point Mode Time Settings 5. 6. 2. This page allows you to set the time manually or to configure automatic time synchronization. The Router can automatically update the time from an NTP server via the internet. 1. Visit http://tplinkwifi.net, and log in with the default username and password: admin. 2. Go to System Tools > Time Settings. To set time manually:

1. Select your local time zone. 2. Enter the Date in Month/Day/Year format. 3. Enter the Time in Hour/Minute/Second format. 4. Click Save. To set time automatically:

5. Select your local time zone. 6. Enter the address or domain of the NTP Server I or NTP Server II. 7. Click Get GMT to get time from the internet if you have connected to the internet. To set Daylight Saving Time:

1. Select Enable DaylightSaving. 2. Select the start time from the drop-down list in the Start field. 3. Select the end time from the drop-down list in the End field. 86 Chapter 5 Configure the Router in Access Point Mode 4. Click Save. Note:

This setting will be used for some time-based functions such as firewall. You must specify your time zone once you log in to the router successfully; otherwise, time-based functions will not take effect. 5. 6. 3. Diagnostic Diagnostic is used to test the connectivity between the router and the host or other network devices. 1. Visit http://tplinkwifi.net, and log in with the default username and password:admin. 2. Go to System Tools > Diagnostic. Diagnostic Tool - Select one diagnostic tool. Ping - This diagnostic tool troubleshoots connectivity, reachability, and name resolution to a given host or gateway. Tracerouter - This diagnostic tool tests the performance of a connection. Note:

Only one user can use this tool at one time. Options Number of Pings, Ping Size and Ping Timeout are used for the Ping function. Option Tracert Hops is used for the Tracert function. Firmware Upgrade 5. 6. 4. TP-Link is dedicated to improving and richening the product features, giving users a better network experience. We will release the latest firmware at TP-Link official website. You can download the latest firmware file from the Support page of our website www.tp-link.com and upgrade the firmware to the latest version. 1. Download the latest firmware file for the router from our website www.tp-link.com. 2. Visit http://tplinkwifi.net, and log in with the default username and password:admin. 3. Go to System Tools > Firmware Upgrade. 4. Click Browse to locate the downloaded firmware file, and click Upgrade. Factory Defaults 5. 6. 5. 1. Visit http://tplinkwifi.net, and log in with the default username and password:admin. 88 Chapter 5 Configure the Router in Access Point Mode 2. Go to System Tools > Factory Defaults. Click Restore to reset all settings to the default values. The default Username: admin The default Password: admin The default IP Address: 192.168.0.254 The default Subnet Mask: 255.255.255.0 Backup & Restore 5. 6. 6. The configuration settings are stored as a configuration file in the router. You can backup the configuration file in your computer for future use and restore the router to the previous settings from the backup file when needed. 1. Visit http://tplinkwifi.net, and log in with the default username and password:admin. 2. Go to System Tools > Backup & Restore. To backup configuration settings:

Click Backup to save a copy of the current settings in your local computer. A .bin file of the current settings will be stored in your computer. To restore configuration settings:

1. Click Choose File to locate the backup configuration file stored in your computer, and 2. Wait a few minutes for the restoring and rebooting. Note: During the restoring process, do not power off or reset the router. click Restore. Reboot 5. 6. 7. 1. Visit http://tplinkwifi.net, and log in with the default username and password:admin. 2. Go to System Tools > Reboot, and you can restart your router. 89 Chapter 5 Configure the Router in Access Point Mode Some settings of the router will take effect only after rebooting, including:

Change the LAN IP Address (system will reboot automatically). Change the DHCP Settings. Change the Working Modes. Change the Web Management Port. Upgrade the firmware of the router (system will reboot automatically). Restore the router to its factory defaults (system will reboot automatically). Update the configuration with the file (system will reboot automatically). 5. 6. 8. 1. Visit http://tplinkwifi.net, and log in with the default username and password:admin. 2. Go to System Tools > Password, and you can change the factory default username Password and password of the router. It is strongly recommended that you change the default username and password of the router, for all users that try to access the routers web-based utility or Quick Setup will be prompted for the routers username and password. Note:

The new username and password must not exceed 15 characters and not include any spacing. 3. Click Save. 5. 6. 9. 1. Visit http://tplinkwifi.net, and log in with the default username and password: admin. 2. Go to System Tools > Language, and you can view the logs of the router. 3. Select the language you prefer from the pull-down list, and then click Save. Language 90 Chapter 5 Configure the Router in Access Point Mode 5. 6. 10. System Log 1. Visit http://tplinkwifi.net, and log in with the default username and password: admin. 2. Go to System Tools > System Log, and you can view the logs of the router. Auto Mail Feature - Indicates whether the auto mail feature is enabled or not. Mail Settings - Set the receiving and sending mailbox address, server address, validation information as well as the timetable for Auto Mail Feature. 91 Chapter 5 Configure the Router in Access Point Mode From - Your mail box address. The router will connect it to send logs. To - Recipients mail address. The destination mailbox which will receive logs. SMTP Server - Your smtp server. It corresponds with the mailbox filled in the From field. You can log on the relevant website for help if you are not clear with the address. Authentication - Most SMTP Server requires Authentication. It is required by most mailboxes that need user name and password to log in. Note:

Only when you select Authentication, do you have to enter the user name and password in the following fields. User Name - Your mail account name filled in the From field. The part behind @

is included. Password - Your mail account password. Confirm The Password - Enter the password again to confirm. Enable Auto Mail Feature - Select it to mail logs automatically. You could mail the current logs either at a specified time everyday or by intervals, but only one could be the current effective rule. Enter the desired time or intervals in the corresponding field. Click Save to apply your settings. Click Back to return to the previous page. Log Type - By selecting the log type, only logs of this type will be shown. Log Level - By selecting the log level, only logs of this level will be shown. Refresh - Refresh the page to show the latest log list. Save Log - Click to save all the logs in a txt file. Mail Log - Click to send an email of current logs manually according to the address and validation information set in Mail Settings. Clear Log - All the logs will be deleted from the router permanently, not just from the page. Click Next to go to the next page, or click Previous to return to the previous page. Log Out 5. 7. Click Logout at the bottom of the main menu, and you will log out of the web page and return to the login window. 92 Chapter 6 Configure the Router in Repeater Mode This chapter presents how to configure the various features of the router working as a Repeater. It contains the following sections:

Status Operation Mode Network Wireless DHCP System Tools Log Out Chapter 6 Configure the Router in Repeater Mode 6. 1. Status 1. Visit http://tplinkwifi.net, and log in with the default username and password:admin. 2. Go to Status. You can view the current status information of the router in Repeater Mode. Firmware Version - The version information of the routers firmware. Hardware Version - The version information of the routers hardware. LAN - This field displays the current settings of the LAN, and you can configure them on the Network > LAN page. MAC address - The physical address of the router. Subnet Mask - The subnet mask associated with the LAN IP address. IP address - The LAN IP address of the router. Wireless - This field displays the basic information or status of the wireless function, and you can configure them on the Wireless > Wireless Settings page. Operation Mode - The current wireless working mode in use. Wireless Radio - Indicates whether the wireless feature is enabled or disabled. Wireless Name of Root AP - The SSID of the root router. Name(SSID) - The wireless network name of the router. Mode - The current wireless working mode. Channel - The current wireless channel. 94 Chapter 6 Configure the Router in Repeater Mode Channel Width - The current wireless channel width. MAC Address - The physical address of the router. WDS Status - The status of the WDS connection is displayed. System Up Time - The length of the time since the router was last powered on or reset. Click Refresh to get the latest status and settings of the router. 6. 2. Operation Mode 1. Visit http://tplinkwifi.net, and log in with the default username and password: admin. 2. Go to Operation Mode. 3. Select Repeater as needed and click Save. 6. 3. Network 6. 3. 1. 1. Visit http://tplinkwifi.net, and log in with the default username and password:admin. 2. Go to Network > LAN. 3. Configure the IP parameters of the LAN and click Save. LAN 95 Chapter 6 Configure the Router in Repeater Mode Type - Either select Smart IP(DHCP) to get IP address from DHCP server, or Static IP to configure IP address manually. MAC Address - The physical address of the LAN ports. The value can not be changed. IP Address - Enter the IP address in dotted-decimal notation if your select Static IP

(factory default - 192.168.0.254). Subnet Mask - An address code that determines the size of the network. Normally 255.255.255.0 is used as the subnet mask. Note:

If you have changed the IP address, you must use the new IP address to log in. If you select Smart IP(DHCP), the DHCP server of the router will not start up. If the new IP address you set is not in the same subnet as the old one, the IP Address pool in the DHCP Server will be configured automatically, but the Virtual Server and DMZ Host will not take effect until they are re-configured. 6. 4. Wireless 6. 4. 1. Connect to Network In this page, you can connect to an existing wireless network in your home for boosting the wireless network coverage. 1. Visit http://tplinkwifi.net, and log in with the default username and password: admin. 2. Go to Wireless > Connect to Network. 3. Click Wireless Scanner, select the wireless network you want to extend from the AP List and click Connect. 96 Chapter 6 Configure the Router in Repeater Mode 4. The SSID and MAC Address of the network will be filled automatically in the corresponding fields. Enter its password and click Save. Extended Network 6. 4. 2. 1. Visit http://tplinkwifi.net, and log in with the default username and password: admin. 2. Go to Wireless > Extended Network. 3. Configure the extended network settings and click Save. Extended SSID - Either use the Copy Host SSID button to automatically copy the main router/APs SSID or enter a new name (up to 32 characters long). This field is case-

sensitive. Copy Host SSID - Click to copy the Host SSID. When selected, the extended network will share the SSID of your host network. Extended Security - Select one of the security options to set local extended wireless network. No Security - This option disables the wireless security. WPA-PSK/WPA2-PSK - This option supports multiple implementation of the WPA (Wi-Fi Protected Access) standard, such as WPA and WPA2. WEP - This option is the most basic form of wireless security that can be used if your client devices can only access wireless using WEP (Wired Equivalent Privacy). 6. 4. 3. Wireless MAC Filtering Wireless MAC Filtering is used to deny or allow specific wireless client devices to access your network by their MAC addresses. 97 Chapter 6 I want to:

How can I do that?

Configure the Router in Repeater Mode Deny or allow specific wireless client devices to access my network by their MAC addresses. For example, you want the wireless client A with the MAC address 00-0A-EB-B0-00-0B and the wireless client B with the MAC address 00-0A-EB-00-07-5F to access the router, but other wireless clients cannot access the router 1. Visit http://tplinkwifi.net, and log in with the default username and password: admin. 2. Go to Wireless > Wireless MAC Filtering. 3. Click Enable to enable the Wireless MAC Filtering function. 4. Select Allow the stations specified by any enabled entries in the list to access as the filtering rule. 5. Delete all or disable all entries if there are any entries already. 6. Click Add New and fill in the blank. 00-07-5F in the MAC Address field. 1 ) Enter the MAC address 00-0A-EB-B0-00-0B/00-0A-EB-

Now only client A and client B can access your network. 98 Chapter 6 Configure the Router in Repeater Mode 6. 4. 4. Wireless Advanced 1. Visit http://tplinkwifi.net, and log in with the default username and password:admin. 2. Go to Wireless > Wireless Advanced. 3. Configure the advanced settings of your wireless network and click Save. Note:

If you are not familiar with the setting items on this page, its strongly recommended to keep the provided default values;

otherwise it may result in lower wireless network performance. Transmit Power - Select High, Middle or Low which you would like to specify for the router. High is the default setting and recommended. Beacon Interval - Enter a value between 40-1000 milliseconds for Beacon Interval here. Beacon Interval value determines the time interval of the beacons. The beacons are the packets sent by the Router to synchronize a wireless network. The default value is 100. RTS Threshold - Here you can specify the RTS (Request to Send) Threshold. If the packet is larger than the specified RTS Threshold size, the Router will send RTS frames to a particular receiving station and negotiate the sending of a data frame. The default value is 2346. Fragmentation Threshold - This value is the maximum size determining whether packets will be fragmented. Setting a low value for the Fragmentation Threshold may result in poor network performance because of excessive packets. 2346 is the default setting and is recommended. DTIM Interval - This value determines the interval of the Delivery Traffic Indication Message (DTIM). A DTIM field is a countdown field informing clients of the next window for listening to broadcast and multicast messages. When the Router has buffered broadcast or multicast messages for associated clients, it sends the next DTIM with a DTIM Interval value. You can specify the value between 1-255 Beacon Intervals. The default value is 1, which indicates the DTIM Interval is the same as Beacon Interval. 99 Chapter 6 Configure the Router in Repeater Mode Enable WMM - WMM function can guarantee the packets with high-priority messages being transmitted preferentially. It is strongly recommended to enable this function. Enable Short GI - It is recommended to enable this function, for it will increase the data capacity by reducing the guard interval time. Enable AP Isolation - This function isolates all connected wireless stations so that wireless stations cannot access each other through WLAN. This function will be disabled if WDS/Bridge is enabled. 6. 4. 5. Wireless Statistics 1. Visit http://tplinkwifi.net, and log in with the default username and password:admin. 2. Go to Wireless > Wireless Statistics to check the data packets sent and received by each client device connected to the router. MAC Address - The MAC address of the connected wireless client. Current Status - The running status of the connected wireless client. Received Packets - Packets received by the wireless client. Sent Packets - Packets sent by the wireless client. Configure - The button is used for loading the item to the Wireless MAC Filtering list. Allow - If the Wireless MAC Filtering function is enabled, click this button to allow the client to access your network. Deny - If the Wireless MAC Filtering function is enabled, click this button to deny the client to access your network. Throughput Monitor 6. 4. 6. 1. Visit http://tplinkwifi.net, and log in with the default username and password:admin. 2. Go to Wireless > Throughput Monitor to view the wireless throughput information. 100 Chapter 6 Configure the Router in Repeater Mode Rate - The unit for the Throughput. Run Time - How long Throughput Monitor runs. Transmit - Wireless transmit rate information. Receive - Wireless receive rate information. Click Start / Stop to start or stop wireless throughput monitor. 6. 5. DHCP By default, the DHCP (Dynamic Host Configuration Protocol) Server is enabled and the router acts as a DHCP server; it dynamically assigns TCP/IP parameters to client devices from the IP Address Pool. You can change the settings of DHCP Server if necessary, and you can reserve LAN IP addresses for specified client devices. 6. 5. 1. DHCP Settings 1. Visit http://tplinkwifi.net, and log in with the default username and password:admin. 2. Go to DHCP > DHCP Settings. 3. Specify DHCP server settings and click Save. 101 Chapter 6 Configure the Router in Repeater Mode DHCP Server - Enable or disable the DHCP server. If disabled, you must have another DHCP server within your network or else you must configure the computer manually. Start IP Address - Specify an IP address for the DHCP Server to start with when assigning IP addresses. 192.168.0.100 is the default start address. End IP Address - Specify an IP address for the DHCP Server to end with when assigning IP addresses. 192.168.0.199 is the default end address. Address Lease Time - The Address Lease Time is the amount of time a network user will be allowed to connect to the router with the current dynamic IP Address. When time is up, the user will be automatically assigned a new dynamic IP address. The range of the time is 1 ~ 2880 minutes. The default value is 120. Default Gateway (Optional) - It is suggested to input the IP address of the LAN port of the router. The default value is 192.168.0.254. Default Domain (Optional) - Input the domain name of your network. DNS Server (Optional) - Input the DNS IP address provided by your ISP. Secondary DNS Server (Optional) - Input the IP address of another DNS server if your ISP provides two DNS servers. Note:

To use the DHCP server function of the router, you must configure all computers on the LAN as Obtain an IP Address automatically. When you choose Static IP in Network > LAN, the DHCP Server function will be disabled. 6. 5. 2. DHCP Client List 1. Visit http://tplinkwifi.net, and log in with the default username and password:admin. 2. Go to DHCP > DHCP Client List to view the information of the clients connected to the router. Client Name - The name of the DHCP client. MAC Address - The MAC address of the DHCP client. Assigned IP - The IP address that the router has allocated to the DHCP client. Lease Time - The time of the DHCP client leased. After the dynamic IP address has expired, a new dynamic IP address will be automatically assigned to the user. You cannot change any of the values on this page. To update this page and show the current attached devices, click Refresh. 102 Chapter 6 Configure the Router in Repeater Mode LED Control 6. 6. System Tools 6. 6. 1. The LED control feature allows you to turn off or on the LEDs of the router automatically when needed. 1. Visit http://tplinkwifi.net, and log in with the default username and password: admin. 2. Go to System Tools > LED Control. 3. Tick Night Mode and select the LED Off Time from the pull-down lists. Then click Save. Time Settings 6. 6. 2. This page allows you to set the time manually or to configure automatic time synchronization. The Router can automatically update the time from an NTP server via the internet. 1. Visit http://tplinkwifi.net, and log in with the default username and password: admin. 2. Go to System Tools > Time Settings. 103 Chapter 6 Configure the Router in Repeater Mode To set time manually:

1. Select your local time zone. 2. Enter the Date in Month/Day/Year format. 3. Enter the Time in Hour/Minute/Second format. 4. Click Save. To set time automatically:

1. Select Enable DaylightSaving. 2. Select the start time from the drop-down list in the Start field. 3. Select the end time from the drop-down list in the End field. 4. Click Save. Note:

This setting will be used for some time-based functions such as firewall. You must specify your time zone once you log in to the router successfully; otherwise, time-based functions will not take effect. 104 Chapter 6 Configure the Router in Repeater Mode 6. 6. 3. Diagnostic Diagnostic is used to test the connectivity between the router and the host or other network devices. 1. Visit http://tplinkwifi.net, and log in with the default username and password:admin. 2. Go to System Tools > Diagnostic. Diagnostic Tool - Select one diagnostic tool. Ping - This diagnostic tool troubleshoots connectivity, reachability, and name resolution to a given host or gateway. Tracerouter - This diagnostic tool tests the performance of a connection. Note:

Only one user can use this tool at one time. Options Number of Pings, Ping Size and Ping Timeout are used for the Ping function. Option Tracert Hops is used for the Tracert function. Ping Watch Dog 6. 6. 4. The Ping Watch Dog is dedicated for continuous monitoring of the particular connection to remote host using the Ping tool. It makes the router continuously ping a user defined IP address (it can be the internet gateway for example). If it is unable to ping under the user defined constraints, the router will automatically reboot. 1. Visit http://tplinkwifi.net, and log in with the default username and password:admin. 2. Go to System Tools > Ping Watch Dog. Configure the settings and click Save. Enable - Turn on/off Ping Watch Dog. IP Address - The IP address of the target host where the Ping Watch Dog Utility is sending ping packets. Interval - Time interval between two ping packets which are sent out continuously. Delay - Time delay before first ping packet is sent out when the router is restarted. Fail Count - Upper limit of the ping packets the router can drop continuously. If this value is overrun, the router will restart automatically. 106 Chapter 6 Configure the Router in Repeater Mode Firmware Upgrade 6. 6. 5. TP-Link is dedicated to improving and richening the product features, giving users a better network experience. We will release the latest firmware at TP-Link official website. You can download the latest firmware file from the Support page of our website www.tp-link.com and upgrade the firmware to the latest version. 1. Download the latest firmware file for the router from our website www.tp-link.com. 2. Visit http://tplinkwifi.net, and log in with the default username and password:admin. 3. Go to System Tools > Firmware Upgrade. 4. Click Browse to locate the downloaded firmware file, and click Upgrade. Factory Defaults 6. 6. 6. 1. Visit http://tplinkwifi.net, and log in with the default username and password:admin. 2. Go to System Tools > Factory Defaults. Click Restore to reset all settings to the default values. The default Username: admin The default Password: admin The default IP Address: 192.168.0.254 The default Subnet Mask: 255.255.255.0 Backup & Restore 6. 6. 7. The configuration settings are stored as a configuration file in the router. You can backup the configuration file in your computer for future use and restore the router to the previous settings from the backup file when needed. 1. Visit http://tplinkwifi.net, and log in with the default username and password:admin. 2. Go to System Tools > Backup & Restore. 107 Chapter 6 Configure the Router in Repeater Mode To backup configuration settings:

Click Backup to save a copy of the current settings in your local computer. A .bin file of the current settings will be stored in your computer. 1. Click Choose File to locate the backup configuration file stored in your computer, and 2. Wait a few minutes for the restoring and rebooting. Note: During the restoring process, do not power off or reset the router. To restore configuration settings:

click Restore. Reboot 6. 6. 8. 1. Visit http://tplinkwifi.net, and log in with the default username and password:admin. 2. Go to System Tools > Reboot, and you can restart your router. Some settings of the router will take effect only after rebooting, including:

Change the LAN IP Address (system will reboot automatically). Change the DHCP Settings. Change the Working Modes. Change the Web Management Port. Upgrade the firmware of the router (system will reboot automatically). Restore the router to its factory defaults (system will reboot automatically). Update the configuration with the file (system will reboot automatically). 6. 6. 9. 1. Visit http://tplinkwifi.net, and log in with the default username and password:admin. 2. Go to System Tools > Password, and you can change the factory default username Password and password of the router. 108 Chapter 6 Configure the Router in Repeater Mode It is strongly recommended that you change the default username and password of the router, for all users that try to access the routers web management page or Quick Setup will be prompted for the routers username and password. Note:

The new username and password must not exceed 15 characters and not include any spacing. 3. Click Save. 6. 6. 10. Language 1. Visit http://tplinkwifi.net, and log in with the default username and password: admin. 2. Go to System Tools > Language, and you can view the logs of the router. 3. Select the language you prefer from the pull-down list, and then click Save. 109 Chapter 6 Configure the Router in Repeater Mode 6. 6. 11. System Log 1. Visit http://tplinkwifi.net, and log in with the default username and password:admin. 2. Go to System Tools > System Log, and you can view the logs of the router. Auto Mail Feature - Indicates whether the auto mail feature is enabled or not. Mail Settings - Set the receiving and sending mailbox address, server address, validation information as well as the timetable for Auto Mail Feature. From - Your mail box address. The router will connect it to send logs. To - Recipients mail address. The destination mailbox which will receive logs. SMTP Server - Your smtp server. It corresponds with the mailbox filled in the From field. You can log in to the relevant website for help if you are not clear with the address. 110 Chapter 6 Configure the Router in Repeater Mode Authentication - Most SMTP Server requires Authentication. It is required by most mailboxes that need user name and password to log in. Note:

Only when you select Authentication, do you have to enter the user name and password in the following fields. User Name - Your mail account name filled in the From field. The part behind @

is included. Password - Your mail account password. Confirm The Password - Enter the password again to confirm. Enable Auto Mail Feature - Select it to mail logs automatically. You could mail the current logs either at a specified time everyday or by intervals, but only one could be the current effective rule. Enter the desired time or intervals in the corresponding field. Click Save to apply your settings. Click Back to return to the previous page. Log Type - By selecting the log type, only logs of this type will be shown. Log Level - By selecting the log level, only logs of this level will be shown. Refresh - Refresh the page to show the latest log list. Save Log - Click to save all the logs in a txt file. Mail Log - Click to send an email of current logs manually according to the address and validation information set in Mail Settings. Clear Log - All the logs will be deleted from the router permanently, not just from the page. Click Next to go to the next page, or click Previous to return to the previous page. 6. 7. Log Out Click Logout at the bottom of the main menu, and you will log out of the web page and return to the login window. 111 FAQQ1. What should I do if I forget my wireless password?

The default wireless password is printed on the label of the router. If the password has been altered, please connect your computer to the router using an Ethernet cable and follow the steps below:

1. Visit http://tplinkwifi.net, and log in with the username and password you set for the 2. Go to Wireless > Wireless Security to retrieve or reset your wireless password. Q2. What should I do if I forget my login password of the web management router. page?

The default username and password of the web management page are admin (in lowercase). If you have altered the username and password but Password Recovery is disabled:

1. Please press and hold the Reset button for about 7 seconds to reset the router. 2. Visit http://tplinkwifi.net, and enter admin (in lowercase) as both username and password to log in. Note: Youll need to reconfigure the router to surf the internet once the router is reset, and please mark down your new password for future use. Q3. What should I do if I cannot access the routers web management page?

This can happen for a variety of reasons. Please try the following:

Make sure your computer has connected to the router correctly and the corresponding LED light up. Make sure the IP address of your computer is configured as Obtain an IP address automatically and Obtain DNS server address automatically. Verify that http://tplinkwifi.net or 192.168.0.1 is correctly entered in the web browser. Check your computers settings:

1. Go to Start > Control Panel > Network and Internet, and click View network status and tasks. 112 1 ) Click Internet Options on the bottom left. 2 ) Click Connections and select Never dial a connection. 3 ) Click LAN settings and deselect the following three options, and click OK. 113 4 ) Go to Advanced > Restore advanced settings, and click OK to save the settings. Use another web browser or computer to log in again. Reset the router to its factory default settings and try again. If the login still fails, please contact the technical support. Q4. How do I use the WDS Bridging function to extend my wireless network?

For example, my house covers a large area. The wireless coverage of the router Im using (the host router) is limited. I want to use an extended router to extend the wireless network of the host router. Note:

WDS bridging only requires configuration on the extended router. 1. Visit http://tplinkwifi.net, and log in to with the username and password you set for the router. 2. Configure the IP address of the router:

1 ) Go to Network > LAN, and set the IP address of the extended router to be in the same subnet with the host router; (for example, if the IP address of the 114 host router is 192.168.0.1, the IP address of the extended router should be 192.168.0.2~192.168.0.254. Here we take 192.168.0.2 for example). 2 ) Click Save. Note: Log in to the web management page again if the IP address of the router has been altered. 3. Survey the SSID to be bridged:

1 ) Go to Wireless > Wireless Settings and click Enable WDS Bridging. 2 ) Click Survey, locate the host routers SSID and click Choose (here we take TP-Link_2512 for example). If the host router is set with a wireless password, you should enter its wireless password. 4 ) Click Save. 3 ) 4. Disable DHCP: Go to DHCP, select Disable, and click Save. Now you can go to Status to check the WDS status. When the WDS status is Run, it means WDS bridging is successfully built. 115 Q5. What should I do if I cannot access the Internet after the configuration in router mode?

1. Visit http://tplinkwifi.net, and log in to with the username and password you set for the router. 2. Go to Status to check WAN status:

If the IP address is a valid one, please try the following:

Your computer might not recognize any DNS server addresses. Please manually configure DNS server. 1 ) Go to DHCP. 2 ) Enter 8.8.8.8 as Primary DNS, and click Save. Tips: 8.8.8.8 is a safe and public DNS server operated by Google. Restart the modem and the router. 1 ) Power off your modem and the router, and leave them off for 1 minute. 2 ) Power on your modem first, and wait about 2 minutes. 3 ) Power on the router, and wait another 1 or 2 minutes and check the internet access. Reset the router to its factory default settings and reconfigure the router. Upgrade the firmware of the router. Check the TCP/IP settings on the particular device if all other devices can get internet from the router. If the IP address is 0.0.0.0, please try the following:

Make sure the physical connection between the router and the modem is established. Clone the MAC address of your computer. 116 1 ) Visit http://tplinkwifi.net, and log in with the username and password you set for the router. 2 ) Go to Network > MAC Clone, select Clone MAC Address and click Save. Tips:

Some ISP may register the MAC address of your computer when you access the internet for the first time through their Cable modem. If you add a router into your network to share your internet connection, the ISP will not accept it as the MAC address is changed, so we need to clone your computers MAC address to the router. The MAC addresses of a computer in wired connection and wireless connection are different. Modify the LAN IP address of the router. Note:

Most TP-Link routers use 192.168.0.1/192.168.1.1 as their default LAN IP address, which may conflict with the IP range of your existent ADSL modem/router. If so, the router is not able to communicate with your modem and cause you cant access the internet. To resolve this problem, we need to change the LAN IP address of the router to avoid such conflict, for example, 192.168.2.1. 1 ) Visit http://tplinkwifi.net, and log in with the username and password you set for 2 ) Go to Network > LAN. 3 ) Modify the LAN IP address as the follow picture shows. Here we take 192.168.2.1 the router. as an example. 4 ) Click Save. Restart the modem and the router. 1 ) Power off your modem and the router, and leave them off for 1 minute. 2 ) Power on your modem first, and wait about 2 minutes. 3 ) Power on the router, and wait another 1 or 2 minutes and check the internet access. Double check the Internet Connection Type. 117 1 ) Confirm your Internet Connection Type, which can be got from the ISP. 2 ) Visit http://tplinkwifi.net, and log in with the username and password you set for the router. 3 ) Go to Network > WAN. 4 ) Select your WAN Connection Type and fill in other parameters. 5 ) Click Save. 6 ) Restart the modem and the router. Please upgrade the firmware of the router. If youve tried every method above but still cannot access the internet, please contact the technical support. Q6. What should I do if I cannot find my wireless network or I cannot connect the wireless network?

If you fail to find any wireless network, please follow the steps below:

Make sure the wireless function of your device is enabled if youre using a laptop with a built-in wireless adapter. You can refer to the relevant document or contact the laptops manufacturer. Make sure the wireless adapter driver is installed successfully and the wireless adapter is enabled. On Windows 7 1 ) If you see the message No connections are available, it is usually because the wireless function is disabled or blocked somehow. 118 2 ) Clicking Troubleshoot and Windows might be able to fix the problem by itself. On Windows XP 1 ) If you see the message Windows cannot configure this wireless connection, this is usually because Windows configuration utility is disabled or you are running another wireless configuration tool to connect the wireless network. 2 ) Exit the wireless configuration tool (the TP-Link Utility, for example). 3 ) Select and right click My Computer on Desktop, and select Manage to open Computer Management window. 4 ) Go to Services and Applications > Services, and find and locate Wireless Zero Configuration in the Services list on the right side. 5 ) Right click Wireless Zero Configuration, and then select Properties. 6 ) Change Startup type to Automatic, click Start and make sure the Service status is Started. And then click OK. If you can find other wireless network except your own, please follow the steps below:

Check the WLAN LED indicator on your wireless router. Make sure your computer/device is still in the range of your router/modem. Move closer if it is currently too far away. If you can find your wireless network but fail to connect, please follow the steps below:

Authenticating problem/password mismatch:

1 ) Sometimes you will be asked to type in a PIN when you connect to the wireless network for the first time. This PIN is different from the Wireless Password/

Network Security Key. Usually you can only find it on the label of your router. 2 ) 3 ) If you cannot find the PIN or entering the PIN still does not work, you may choose Connecting using a security key instead, and then type in the Wireless Password/Network Security Key. If it continues to show the note Network Security Key Mismatch, it is suggested to confirm the wireless password of your wireless router. 119 Note: Wireless Password/Network Security Key is case sensitive. Windows unable to connect to XXXX / Can not join this network / Taking longer than usual to connect to this network:

Check the wireless signal strength of your network. It is weak (1~3 bars), please move the router closer and try again. Change the wireless channel of the router to 1, 6, or 11 to reduce interference from other networks. Re-install or update the driver for your wireless adapter of the computer. 120 COPYRIGHT & TRADEMARKS is a registered trademark Specifications are subject to change without notice. of TP-Link Technologies Co., Ltd. Other brands and product names are trademarks or registered trademarks of their respective holders. No part of the specifications may be reproduced in any form or by any means or used to make any derivative such as translation, transformation, or adaptation without permission from TP-Link Technologies Co., Ltd. Copyright 2017 TP-Link Technologies Co., Ltd. All rights reserved. 121 FCC STATEMENT This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/ TV technician for help. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference. 2. This device must accept any interference received, including interference that may cause undesired operation. Any changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. Note: The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment. Such modifications could void the users authority to operate the equipment. For product available in the USA/Canada market, only channel 1~11 can be operated. Selection of other channels is not possible. FCC RF Radiation Exposure Statement This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This device and its antenna must not be co-located or operating in conjunction with any other antenna or transmitter. To comply with FCC RF exposure compliance requirements, this grant is applicable to only Mobile Configurations. The antennas used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-

located or operating in conjunction with any other antenna or transmitter. 122 CE Mark Warning This is a class B product. In a domestic environment, this product may cause radio interference, in which case the user may be required to take adequate measures. All operational modes:

2.4GHz: 802.11b, 802.11g, 802.11n (HT20), 802.11n (HT40) The frequency, mode and the maximum transmitted power in EU are listed below:

2412-2472MHz (802.11n HT20 MCS0): 19.98 dBm RF Exposure Information This device meets the EU requirements (1999/5/EC Article 3.1a) on the limitation of exposure of the general public to electromagnetic fields by way of health protection. The device complies with RF specifications when the device used at 20 cm from your body. Canadian Compliance Statement This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions:

1. This device may not cause interference, and 2. This device must accept any interference, including interference that may cause undesired operation of the device. Le prsent appareil est conforme aux CNR dIndustrie Canada applicables aux appareils radio exempts de licence. Lexploitation est autorise aux deux conditions suivantes :

1. lappareil ne doit pas produire de brouillage;

2. lutilisateur de lappareil doit accepter tout brouillage radiolectrique subi, meme si le brouillage est susceptible den compromettre le fonctionnement. Radiation Exposure Statement:

This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. Dclaration dexposition aux radiations:

Cet quipement est conforme aux limites dexposition aux rayonnements IC tablies pour un environnement non contrl. Cet quipement doit tre install et utilis avec un minimum de 20 cm de distance entre la source de rayonnement et votre corps. Industry Canada Statement CAN ICES-3 (B)/NMB-3(B) Korea Warning Statements:

. 123 NCC Notice & BSMI Notice:

. Safety Information When product has power button, the power button is one of the way to shut off the product; when there is no power button, the only way to completely shut off power is to disconnect the product or the power adapter from the power source. Dont disassemble the product, or make repairs yourself. You run the risk of electric shock and voiding the limited warranty. If you need service, please contact us. Avoid water and wet locations. Adapter shall be installed near the equipment and shall be easily accessible. 124 The plug considered as disconnect device of adapter. Use only power supplies which are provided by manufacturer and in the original packing of this product. If you have any questions, please dont hesitate to contact us. Explanations of the symbols on the product label Symbol Explanation DC voltage RECYCLING This product bears the selective sorting symbol for Waste electrical and electronic equipment

(WEEE). This means that this product must be handled pursuant to European directive 2012/19/

EU in order to be recycled or dismantled to minimize its impact on the environment. User has the choice to give his product to a competent recycling organization or to the retailer when he buys a new electrical or electronic equipment. 125

		frequency	equipment class	purpose
1	2017-03-30	2412 ~ 2462	DTS - Digital Transmission System	Original Equipment

Application Forms

app s	Applicant Information
1	Effective	2017-03-30
1	Applicant's complete, legal business name	TP-Link Technologies Co., Ltd.
1	FCC Registration Number (FRN)	0013661145
1	Physical Address	Building 24 (floors 1,3,4,5) and 28 (floors1-4)
1		Shenzhen, N/A 518057
1		China

app s	TCB Information
1	TCB Application Email Address	h******@acbcert.com
1	TCB Scope	A4: UNII devices & low power transmitters using spread spectrum techniques

app s	FCC ID
1	Grantee Code	TE7
1	Equipment Product Code	WR841HPV5

app s	Person at the applicant's address to receive grant or for contact
1	Name	J** H**
1	Title	Regulatory Compliance Manager
1	Telephone Number	75521********
1	Fax Number	75526********
1	E-mail	c******@tp-link.com

app s	Technical Contact
1	Firm Name	Sporton International Inc.
1	Name	E** L****
1	Physical Address	No.8, Lane 724, Bo-ai St.
1		Jhubei City, Hsinchu County, 302
1		Taiwan
1	Telephone Number	886-3******** Extension:
1	Fax Number	886-3********
1	E-mail	e******@sporton.com.tw

app s	Non Technical Contact
		n/a

app s	Confidentiality (long or short term)
1	Does this application include a request for confidentiality for any portion(s) of the data contained in this application pursuant to 47 CFR § 0.459 of the Commission Rules?:	Yes
1	Long-Term Confidentiality Does this application include a request for confidentiality for any portion(s) of the data contained in this application pursuant to 47 CFR § 0.459 of the Commission Rules?:	No
	if no date is supplied, the release date will be set to 45 calendar days past the date of grant.

app s	Cognitive Radio & Software Defined Radio, Class, etc
1	Is this application for software defined/cognitive radio authorization?	No
1	Equipment Class	DTS - Digital Transmission System
1	Description of product as it is marketed: (NOTE: This text will appear below the equipment class on the grant)	300Mbps High Power Wireless N Router
1	Related OET KnowledgeDataBase Inquiry: Is there a KDB inquiry associated with this application?	No
1	Modular Equipment Type	Does not apply
1	Purpose / Application is for	Original Equipment
1	Composite Equipment: Is the equipment in this application a composite device subject to an additional equipment authorization?	No
1	Related Equipment: Is the equipment in this application part of a system that operates with, or is marketed with, another device that requires an equipment authorization?	No
1	Grant Comments	Power Output listed is conducted. Device is an 802.11b/g/n device in a 2x2 MIMO configuration as described in this filing. The device has been certified for mobile use and any co-location must be done through the use of FCC multitransmitter product procedures. End-users and installers must be provided with antenna installation instructions and transmitter operating conditions for satisfying RF exposure compliance. This device has 20MHz and 40MHz bandwidth modes.
1	Is there an equipment authorization waiver associated with this application?	No
1	If there is an equipment authorization waiver associated with this application, has the associated waiver been approved and all information uploaded?	No

app s	Test Firm Name and Contact Information
1	Firm Name	Sporton International Inc
1	Name	J****** T**
1	Telephone Number	88633******** Extension:
1	E-mail	j******@sporton.com.tw

Equipment Specifications
	Line	Rule Parts	Grant Notes	Lower Frequency	Upper Frequency	Power Output	Tolerance	Emission Designator	Microprocessor Number
1	1	15C	MO	2412.00000000	2462.00000000	0.2399000

some individual PII (Personally Identifiable Information) available on the public forms may be redacted, original source may include additional details

recent releases: A3LBE201D Samsung Electronics Co Ltd 2BL82-X6 Dongguan Longshengteng Technology Co., Ltd 2BLLU-S21 Shenzhen KEP Technology CO., Ltd PD9BE201D2 Intel Corporation 2BG83-JX-05 Dongguan Jinxu Electronics Co., Ltd