| all | frequencies |
|
exhibits | applications |
|---|---|---|---|---|
| manual |
| app s | submitted / available | |||||||
|---|---|---|---|---|---|---|---|---|
| 1 |
|
User's manual-FCC rev | Users Manual | 3.23 MiB | ||||
| 1 | External Photos | |||||||
| 1 | Cover Letter(s) | |||||||
| 1 | Internal Photos | |||||||
| 1 | ID Label/Location Info | |||||||
| 1 | ID Label/Location Info | |||||||
| 1 | Cover Letter(s) | |||||||
| 1 | Cover Letter(s) | |||||||
| 1 | RF Exposure Info | |||||||
| 1 | Test Setup Photos | |||||||
| 1 | Test Report |
| 1 | User's manual-FCC rev | Users Manual | 3.23 MiB |
TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router Rev: 1.0.0 1910010643 COPYRIGHT & TRADEMARKS Specifications are subject to change without notice. is a registered trademark of TP-LINK TECHNOLOGIES CO., LTD. Other brands and product names are trademarks or registered trademarks of their respective holders. No part of the specifications may be reproduced in any form or by any means or used to make any derivative such as translation, transformation, or adaptation without permission from TP-LINK TECHNOLOGIES CO., LTD. Copyright 2012 TP-LINK TECHNOLOGIES CO., LTD. All rights reserved. http://www.tp-link.com FCC STATEMENT This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna. Connect the equipment into an outlet on a circuit different from that to which the receiver Increase the separation between the equipment and receiver. is connected. Consult the dealer or an experienced radio/ TV technician for help. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
1) This device may not cause harmful interference. 2) This device must accept any interference received, including interference that may cause undesired operation. Any changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. Note: The manufacturer is not responsible for any radio or tv interference caused by unauthorized modifications to this equipment. Such modifications could void the users authority to operate the equipment. FCC RF Radiation Exposure Statement This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This device and its antenna must not be co-located or operating in conjunction with any other antenna or transmitter. To comply with FCC RF exposure compliance requirements, this grant is applicable to only Mobile Configurations. The antennas used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter. CE Mark Warning This is a class B product. In a domestic environment, this product may cause radio interference, in which case the user may be required to take adequate measures. National Restrictions This device is intended for home and office use in all EU countries (and other countries following the EU directive 1999/5/EC) without any limitation except for the countries mentioned below:
Country Restriction Reason/remark Bulgaria Italy None None Luxembourg None Norway Implemented General authorization required for outdoor use and public service If used outside of own premises, general authorization is required General authorization required for network and service supply(not for spectrum) This subsection does not apply for the geographical area within a radius of 20 km from the centre of Ny-lesund This device has been designed to operate with the antennas listed below, and having a maximum gain of 5 dBi. Antennas not included in this list or having a gain greater than 5 dBi are strictly prohibited for use with this device. The required antenna impedance is 50 ohms. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that permitted for successful communication. Industry Canada Statement:
This device complies with RSS-210 of the Industry Canada Rules. Operation is subject to the following two conditions:
(1)This device may not cause harmful interference, and
(2)This device must accept any interference received, including interference that may cause undesired operation. IMPORTANT NOTE:
Radiation Exposure Statement:
This equipment complies with Canada radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. Ce dispositif est conforme la norme CNR-210 dIndustrie Canada applicable aux appareils radio exempts de licence. Son fonctionnement est sujet aux deux conditions suivantes:
(1) Le dispositif ne doit pas produire de brouillage prjudiciable, et
(2) Ce dispositif doit accepter tout brouillage reu,y compris un brouillage susceptible de provoquer un fonctionnement indsirable. NOTE IMPORTANTE:
Dclaration dexposition aux radiations:
Cet quipement est conforme aux limites dexposition aux rayonnements IC tablies pour un environnement non contrl. Cet quipement doit tre install et utilis avec un minimum de 20 cm de distance entre la source de rayonnement et votre corps. Korea Warning Statements:
. NCC Notice:
. TP-LINK TECHNOLOGIES CO., LTD DECLARATION OF CONFORMITY For the following equipment:
Product Description: 300Mbps Wireless N VoIP ADSL2+ Modem Router Model No.: TD-VG3631 Trademark: TP-LINK We declare under our own responsibility that the above products satisfy all the technical regulations applicable to the product within the scope of Council Directives:
Directives 1999/5/EC, Directives 2004/108/EC, Directives 2006/95/EC, Directives 1999/519/EC, Directives 2011/65/EU The above product is in conformity with the following standards or other normative documents ETSI EN 300 328 V1.7.1: 2006 ETSI EN 301 489-1 V1.9.2:2011& ETSI EN 301 489-17 V2.1.1:2009 EN 55022:2010 EN 55024:2010 EN 61000-3-2:2006+A1:2009+A2:2009 EN 61000-3-3:2008 EN60950-1:2006+A112009+A1:2010+A12:2011 EN62311:2008 ETSI ES203 021 The product carries the CE Mark:
Person is responsible for marking this declaration:
Yang Hongliang Product Manager of International Business TP-LINK TECHNOLOGIES CO., LTD Building 24 (floors 1, 3, 4, 5), and 28 (floors 1-4) Central Science and Technology Park, Shennan Rd, Nanshan, Shenzhen, China Date of issue: 2012 CONTENTS Package Contents ....................................................................................................1 Chapter 1. Product Overview...................................................................................2 1.1 Overview of the Modem Router ...................................................................................... 2 1.2 Main Features................................................................................................................. 3 1.3 Panel Layout................................................................................................................... 4 1.3.1 The Front Panel ................................................................................................................... 4 1.3.2 The Back Panel.................................................................................................................... 6 Chapter 2. Connecting the Modem Router .............................................................8 2.1 System Requirements .................................................................................................... 8 2.2 Installation Environment Requirements .......................................................................... 8 2.3 Connecting the Modem Router....................................................................................... 8 Chapter 3. Quick Installation Guide ......................................................................10 3.1 Configuring the PC ....................................................................................................... 10 3.2 Quick Installation Guide................................................................................................ 13 Chapter 4. Configuring the Modem Router ..........................................................19 4.1 Login............................................................................................................................. 19 4.2 Status............................................................................................................................ 19 4.3 Quick Setup .................................................................................................................. 20 4.4 Network......................................................................................................................... 20 4.4.1 WAN Settings..................................................................................................................... 21 4.4.2 EWAN ................................................................................................................................ 30 4.4.3 Interface Grouping ............................................................................................................. 33 4.4.4 LAN Settings ...................................................................................................................... 34 4.4.5 MAC Clone......................................................................................................................... 36 4.4.6 ALG Settings...................................................................................................................... 36 4.4.7 DSL Settings ...................................................................................................................... 37 4.5 DHCP Server................................................................................................................ 38 4.5.1 DHCP Settings................................................................................................................... 38 4.5.2 Clients List.......................................................................................................................... 40 4.5.3 Address Reservation.......................................................................................................... 40 4.5.4 Conditional Pool................................................................................................................. 41 4.6 Wireless........................................................................................................................ 43 4.6.1 Basic Settings .................................................................................................................... 43 4.6.2 WPS Settings..................................................................................................................... 45 4.6.3 Wireless Security ............................................................................................................... 47 4.6.4 Wireless MAC Filtering ...................................................................................................... 49 4.6.5 Wireless Advanced ............................................................................................................ 51 4.6.6 Wireless Status .................................................................................................................. 52 4.7 Voice............................................................................................................................. 52 4.7.1 SIP Account ....................................................................................................................... 53 4.7.2 Dial Plan............................................................................................................................. 55 4.7.3 Phone Setup ...................................................................................................................... 58 4.7.4 Advanced Setup................................................................................................................. 61 4.7.5 Speed Dial.......................................................................................................................... 63 4.7.6 Call Log .............................................................................................................................. 63 4.7.7 Call Firewall........................................................................................................................ 64 4.7.8 USB Voice Mail .................................................................................................................. 67 4.8 USB Settings ................................................................................................................ 69 4.8.1 USB Mass Storage ............................................................................................................ 69 4.8.2 User Accounts.................................................................................................................... 70 4.8.3 Storage Sharing ................................................................................................................. 71 4.8.4 FTP Server......................................................................................................................... 72 4.8.5 Media Server...................................................................................................................... 74 4.8.6 Print Server ........................................................................................................................ 75 4.9 Route Settings .............................................................................................................. 76 4.9.1 Default Gateway................................................................................................................. 76 4.9.2 Static Route........................................................................................................................ 76 4.9.3 RIP Settings ....................................................................................................................... 77 4.10 Forwarding.................................................................................................................... 78 4.10.1 Virtual Servers .................................................................................................................. 78 4.10.2 Port Triggering.................................................................................................................. 79 4.10.3 DMZ .................................................................................................................................. 81 4.10.4 UPnP ................................................................................................................................ 82 4.11 Parental Control............................................................................................................ 83 4.12 Firewall ......................................................................................................................... 84 4.12.1 Rule .................................................................................................................................. 84 4.12.2 LAN Host .......................................................................................................................... 85 4.12.3 WAN Host......................................................................................................................... 86 4.12.4 Schedule........................................................................................................................... 88 4.13 Traffic Control ............................................................................................................... 89 4.13.1 Control Settings ................................................................................................................ 89 4.13.2 Rules List.......................................................................................................................... 89 4.14 IP&MAC Binding........................................................................................................... 90 4.14.1 Binding Settings................................................................................................................ 91 4.14.2 ARP List............................................................................................................................ 92 4.15 Dynamic DNS ............................................................................................................... 92 4.16 Diagnostic..................................................................................................................... 93 4.17 System Tools................................................................................................................ 94 4.17.1 System Log....................................................................................................................... 94 4.17.2 Time Settings.................................................................................................................... 95 4.17.3 Manage Control ................................................................................................................ 96 4.17.4 CWMP Settings ................................................................................................................ 96 4.17.5 SNMP Settings ................................................................................................................. 97 4.17.6 Backup & Restore............................................................................................................. 98 4.17.7 Factory Defaults................................................................................................................ 98 4.17.8 Firmware Upgrade............................................................................................................ 99 4.17.9 Reboot ............................................................................................................................ 100 4.17.10 Statistics...................................................................................................................... 100 Appendix A: Specifications .................................................................................102 Appendix B: Troubleshooting .............................................................................103 Appendix C: Telephony Features........................................................................115 Appendix D: Telephone Operation......................................................................117 Appendix E: Technical Support ..........................................................................120 TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Package Contents The following contents should be found in your package:
One TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router One Power Adapter for TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router Quick Installation Guide One RJ45 cable Three RJ11 cables One ADSL splitter One Resource CD for TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router, including:
Other Helpful Information This User Guide Note:
Make sure that the package contains the above items. If any of the listed items are damaged or missing, please contact your distributor. 1 TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Chapter 1. Product Overview Thank you for choosing the TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router. 1.1 Overview of the Modem Router The TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router integrates 4-port Switch, Firewall, NAT-Router and Wireless AP. Powered by 2x2 MIMO technology, the Wireless N Router delivers exceptional range and speed, which can fully meet the need of Small Office/Home Office
(SOHO) networks and the users demanding higher networking performance. The TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router utilizes integrated ADSL2+
transceiver and high speed MIPS CPU. The Router supports full-rate ADSL2+ connectivity conforming to the ITU and ANSI specifications. In addition to the basic DMT physical layer functions, the ADSL2+ PHY supports dual latency ADSL2+ framing (fast and interleaved) and the I.432 ATM Physical Layer. The router provides up to 300Mbps wireless connection with other 802.11n wireless clients. The incredible speed makes it ideal for handling multiple data streams at the same time, which ensures your network stable and smooth. The performance of this 802.11n wireless Router will give you the unexpected networking experience at speed 650% faster than 802.11g. It is also compatible with all IEEE 802.11g and IEEE 802.11b products. With multiple protection measures, including SSID broadcast control and wireless LAN 64/128 WEP encryption, Wi-Fi protected Access (WPA2-PSK, WPA-PSK), as well as advanced Firewall protections, the TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router provides complete data privacy. The Router provides flexible access control, so that parents or network administrators can establish restricted access policies for children or staff. It also supports Virtual Server and DMZ host for Port Triggering, and then the network administrators can manage and monitor the network in real time with the remote management function. Since the Router is compatible with virtually all the major operating systems, it is very easy to manage. Quick Setup Wizard is supported and detailed instructions are provided step by step in this user guide. Before installing the Router, please look through this guide to know all the Routers functions. 2 TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide 1.2 Main Features Four 10/100Mbps Auto-Negotiation RJ45 LAN ports (Auto MDI/MDIX), four RJ11 ports, two USB 2.0 ports Provides external splitter. Adopts Advanced DMT modulation and demodulation technology. Supports bridge mode and Router function. Multi-user sharing a high-speed Internet connection. Downstream data rates up to 24Mbps, upstream data rates up to 3.5Mbps (With Annex M enabled). Supports long transfers, the max line length can reach to 6.5Km. Supporting both traditional land lines and VoIP network offers you a multiple choice when making phone calls Various call features such as Multi-accounts, call waiting, call holding, call forwarding, 3-way conference calls and USB voice mail Supports remote configuration and management through SNMP and CWMP. Supports PPPoE, it allows connecting the internet on demand and disconnecting from the Internet when idle. Provides reliable ESD and surge-protect function with quick response semi-conductive surge protection circuit. High speed and asymmetrical data transmit mode, provides safe and exclusive bandwidth. Supports All ADSL industrial standards. Compatible with all mainstreams DSLAM (CO). Provides integrated access of internet and route function which face to SOHO user. Real-time Configuration and device monitoring. Supports Multiple PVC (Permanent Virtual Circuit). Built-in DHCP server. Built-in firewall, supporting IP/MAC filter, Application filter and URL filter. Supports Virtual Server, DMZ host and IP Address Mapping. Supports Dynamic DNS, UPnP and Static Routing. Supports system log and flow Statistics. Supports firmware upgrade and Web management. Provides WPA-PSK/WPA2-PSK data security, TKIP/AES encryption security. Provides 64/128-bit WEP encryption security and wireless LAN ACL (Access Control List). Supports USB Storage Sharing, Print Server, FTP Server, Media Server. Supports Ethernet WAN (EWAN). Supports Bandwidth Control. 3 TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide 1.3 Panel Layout 1.3.1 The Front Panel Figure 1-1 The Routers LEDs are located on the front panel (View from left to right). They indicate the devices working status. For details, please refer to LED Explanation. LED Explanation:
Name Status Indication
(Power) On Off On The modem router is powered on. The modem router is off. Please ensure that the power adapter is connected correctly. ADSL line is synchronized and ready to use.
(ADSL) Flash The ADSL negotiation is in progress.
(Internet) Off On ADSL synchronization troubleshooting. fails. Please refer to Note 1 for The network is available with a successful Internet connection. Flash There is data being transmitted or received via the Internet. Off On There is no successful Internet connection or the modem router is operating for troubleshooting. in Bridge mode. Please to Note 2 refer Wireless is enabled but no data is being transmitted.
(WLAN) Flash The modem router is sending or receiving data over the wireless network. Off On Wireless function is disabled. There is a device connected to this LAN port.
(LAN1-4) Flash The modem router is sending or receiving data over this LAN port. Off On There is no device connected to this LAN port. A storage device or printer has connected to the USB port.
(USB) Flash The modem router is sending or receiving data over this USB port. Off No storage device or printer is plugged into the USB port. 4 TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide On A valid PSTN connection. Line Flash Incoming calls and outgoing calls are transmitted trough PSTN line. Off On PSTN connection fails. The phone is off hook. Phone1-2 Flash The phone is ringing. Off On
(WPS) Slow Flash The phone is on hook. A wireless device has been successfully added to the network by WPS function. WPS handshaking is in process and will continue for about 2 minutes. Please press the WPS button on other wireless devices that you want to add to the network while the LED is flashing. Quick Flash A wireless device has failed to be added to the network by WPS function. Please refer to 4.6.2 WPS Settings for more information. Note:
1. If the ADSL LED is off, please check your Internet connection first. Refer to 2.3 Connecting the Modem Router for more information about how to make Internet connection correctly. If you have already made a right connection, please contact your ISP to make sure if your Internet service is available now. If the Internet LED is off, please check your ADSL LED first. If your ADSL LED is also off, please refer to Note 1. If your ADSL LED is GREEN ON, please check your Internet configuration. You may need to check this part of information with your ISP and make sure everything have been input correctly. 2. 5 TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide 1.3.2 The Back Panel The Router's ports, where the cables are connected, and RESET button are located on the front. Figure 1-2 POWER: The Power plug is where you will connect the power adapter. USB1/USB2: The USB port connects to a USB storage device or a USB printer. PHONE2/PHONE1:The phone port connects to a phone set. LAN1, LAN2, LAN3, LAN4/WAN: Through these ports, you can connect the Router to your PC or the other Ethernet network devices. Enable EWAN function and you will be able to connect to Cable/FTTH/VDSL/ADSL device. LINE: Connect this port to PSTN phone cable. Or you can connect them by an external separate splitter. For details, please refer to 2.3 Connecting the Router. ADSL: Through the port, you can connect the Modem Router with the telephone. Or you can connect them by an external separate splitter. For details, please refer to 2.3 Connecting the Router. Antennas: Used for wireless operation and data transmit. RESET: There are two ways to reset the Router's factory defaults. Method one: With the Router powered on, use a pin to press and hold the Reset button for at least 5 seconds. And the Router will reboot to its factory default settings. Method two: Restore the default setting from Maintenance-SysRestart of the Router's Web-based Utility. Ports and buttons located on the side 6 TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Figure 1-3 WPS: The switch for the WPS function. For details, please refer to 4.6.2 WPS Settings. WiFi: The switch for the WiFi function. ON/OFF: The switch for the power. 7 TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Chapter 2. Connecting the Modem Router 2.1 System Requirements Broadband Internet Access Service (DSL/Cable/Ethernet). PCs with a working Ethernet Adapter and an Ethernet cable with RJ45 connectors. TCP/IP protocol on each PC. Web browser, such as Microsoft Internet Explorer, Mozilla Firefox or Apple Safari. 2.2 Installation Environment Requirements The Product should not be located where it will be exposed to moisture or excessive heat. Place the Router in a location where it can be connected to the various devices as well as to a power source. Make sure the cables and power cord are safely placed out of the way so they do not create a tripping hazard. The Router can be placed on a shelf or desktop. Keep away from the strong electromagnetic radiation and the device of electromagnetic sensitive. 2.3 Connecting the Modem Router Before installing the device, please make sure your broadband service provided by your ISP is available. If there is any problem, please contact your ISP. Before cable connection, cut off the power supply and keep your hands dry. You can follow the steps below to install it. Step 1: Connect the ADSL Line. You can use a separate splitter. External splitter can divide the data and voice, and then you can access the Internet and make calls at the same time. The external splitter has three ports:
LINE: Connect to the wall jack PHONE: Connect to the LINE port of the Modem Router MODEM: Connect to the ADSL port of the Modem Router Step 2: Connect the Ethernet cable. Attach one end of a network cable to your computers Ethernet port or a regular hub/switch port, and the other end to the LAN port on the Modem Router. Step 3: Connect your telephone to the Port labeled PHONE 1/2 on the Modem Router with a telephone line. Step 4: Connect your USB device to the USB port labled USB 1/2 on the Modem Router. If you want to share files or use the USB Voice Mail function, please plug an external USB hard drive/USB flash disk into the USB port. To use the printer function, please connect a USB printer to the USB port. To use USB Voice Mail function, please make sure the free space of the plugged external USB hard drive/USB flash disk is more than 4MB. 8 TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Step 5: Power on the computers and LAN devices. Step 6: Attach the power adapter. Connect the power adapter to the power connector on the rear of the device and plug in the adapter to an electrical outlet or power extension. The electrical outlet shall be installed near the device and shall be easily accessible. Figure 2-1 9 TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Chapter 3. Quick Installation Guide 3.1 Configuring the PC After you directly connect your PC to the Modem Router or connect your adapter to a Hub/Switch which has connected to the Modem Router, you need to configure your PCs IP address. Follow the steps below to configure it. Step 1: Click the Start menu on your desktop, right click My Network Places, and then select Properties (shown in Figure 3-1). Step 2: Right click Local Area Connection (LAN), and then select Properties. Figure 3-1 10 TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Figure 3-2 Step 3: Select General tab, highlight Internet Protocol (TCP/IP), and then click the Properties button. Figure 3-3 11 TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Step 4: Configure the IP address as Figure 3-4 shows. After that, click OK. Figure 3-4 Note:
You can configure the PC to get an IP address automatically, select Obtain an IP address automatically and Obtain DNS server address automatically in the screen above. Now, you can run the Ping command in the command prompt to verify the network connection. Please click the Start menu on your desktop, select run tab, type cmd or command in the field and press Enter. Type ping 192.168.1.1 on the next screen, and then press Enter. If the result displayed is similar to the screen below, the connection between your PC and the Modem Router has been established. Figure 3-5 12 TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide If the result displayed is similar to the screen shown below, it means that your PC has not connected to the Modem Router. You can check it following the steps below:
Figure 3-6 1) 2) Is the connection between your PC and the Modem Router correct?
The LEDs of LAN port which you link to the device and the LEDs on your PC's adapter should be lit. Is the TCP/IP configuration for your PC correct?
If the Router's IP address is 192.168.1.1, your PC's IP address must be within the range of 192.168.1.2 ~ 192.168.1.254. 3.2 Quick Installation Guide With a Web-based utility, it is easy to configure and manage the TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router. The Web-based utility can be used on any Windows, Macintosh or UNIX OS with a Web browser, such as Microsoft Internet Explorer, Mozilla Firefox or Apple Safari. 1. To access the configuration utility, open a web-browser and type the default address http://192.168.1.1 in the address field of the browser. Figure 3-7 After a moment, a login window will appear, similar to the Figure 3-8. Enter admin for the User Name and Password, both in lower case letters. Then click the OK button or press the Enter key. 13 TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Figure 3-8 Note:
1) Do not mix up the user name and password with your ADSL account user name and password which are needed for PPP connections. 2) If the above screen does not pop up, it means that your Web-browser has been set to a proxy. Go to Tools menuNetworkLAN Settings, in the screen that appears, cancel the Using Proxy checkbox, and click OK to finish it. 2. After your successful login, you will see the Login screen as shown in Figure 3-9. Click Quick Setup menu to access Quick Setup Wizard. 14 TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Figure 3-9 3. Change the VPI or VCI values which are used to define a unique path for your connection. If you have been given specific settings for this to configuration, type in the correct values assigned by your ISP. Click Next. 15 TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Figure 3-10 4. Here we select PPPoE WAN Link Type for example, enter the Username, Password and Confirm Password given by your ISP, and then click Next. Figure 3-11 5. On the Wireless screen, we use the default SSID, select Region and Mode. Set a Password or select Disable Security(Disable Security is not recommended.), and then click Next to continue. Figure 3-12 16 TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide 6. Basic parameters of Voice can be set on the Voice screen. Please enter a profile name to identify this account and other parameters provided by your ISP. If you dont want to configure VoIP function now, leave "Profile Name" blank and click Next to skip. Figure 3-13 7. On this page, please confirm all parameters. Click Previous to modify or click the Save button to make the configuration take effect. 8. You will see the Complete screen below, click Finish to complete these settings. Figure 3-14 17 TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Figure 3-15 18 TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Chapter 4. Configuring the Modem Router This chapter will show each Web page's key function and the configuration way. 4.1 Login After your successful login, you will see the fifteen main menus on the left of the Web-based utility. On the right, there are the corresponding explanations and instructions. The detailed explanations for each Web pages key function are listed below. 4.2 Status Choose Status, you can see the corresponding information about Device Information, DSL, WAN, LAN WLAN and Voice. 19 TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Figure 4-1 4.3 Quick Setup Please refer to Section 3.2 Quick Installation Guide. 4.4 Network Choose Network, there are many submenus under the main menu. Click any one of them, and you will be able to configure the corresponding function. 20 TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide 4.4.1 WAN Settings Choose NetworkWAN Settings, and you will see the WAN Port Information Table in the screen similar to Figure 4-2, which describes the WAN port settings and the relevant manipulation to each interface. There are five different configurations for the connection types, which are Static IP, Dynamic IP, PPPoE, IPoA, and Bridge. You can select the corresponding types according to your needs. Figure 4-2 Click Add to add a new entry, you can configure the parameters for ATM and WAN Service in the next screen (shown in Figure 4-3). 21 TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Figure 4-3 4.4.1.1 Static IP Select this option if your ISP provides static IP information to you. You should set static IP address, IP subnet mask, and gateway address in the screen below. 22 TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Figure 4-4 ATM Configuration:
VPI (0~255): Identifies the virtual path between endpoints in an ATM network. The valid range is from 0 to 255. Please input the value provided by your ISP. VCI (1~65535): Identifies the virtual channel endpoints in an ATM network. The valid range is from 1 to 65535 (1 to 31 is reserved for well-known protocols). Please input the value provided by your ISP. Click Advanced, advanced selections of ATM Configuration can be shown. Encapsulation Mode: Select the encapsulation mode for the Static IP Address. Here you can leave it default. ATM Qos Type: Select ATM Qos Type provided by ISP, and the type is UBR by default. WAN Service Setup:
IP Address: Enter the IP address in dotted-decimal notation provided by your ISP. Subnet Mask: Enter the subnet Mask in dotted-decimal notation provided by your ISP, usually is 255.255.255.0. Default Gateway (Optional): Enter the gateway IP address in dotted-decimal notation provided by your ISP. 23 TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide DNS Server/ Secondary DNS Server: Here you can set DNS Server (at least one) manually. The Route will use this DNS Server for priority. Default Gateway: select a WAN Interface from the drop-down list as the IPv4 default gateway. MTU (bytes): Maximum Transmission Unit Size. Check this box then you can change the MTU size. The default MTU value is 1500 Bytes. It is not recommended that you change the default value unless required by your ISP. Enable NAT: This technology translates the IP addresses of a local area network to a different IP address for the Internet. If this Modem Router is hosting your networks connection to the Internet, please select the check box. If another Router exists in your network, you dont need to select the option. Enable Fullcone NAT: It is a type of NAT, if not enabled, the default NAT will act. Enable SPI Firewall: A SPI firewall enhances networks security. Select the option to use a firewall, or else without a firewall. Enable IGMP Proxy: IGMP (Internet Group Management Protocol) is used to manage multicasting on TCP/IP networks. Some ISPs use IGMP to perform remote configuration for client devices, such as the Modem Router. The default value is disabled, and if you are not sure, please contact your ISP or just leave it. Click the Save button to save the settings. 4.4.1.2 Dynamic IP Select this option, the Modem Router will be able to obtain IP network information dynamically from a DHCP server provided by your ISP. 24 TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Figure 4-5 Click Advanced, advanced selections for WAN Service Setup can be shown. MTU (bytes): Maximum Transmission Unit Size. Check this box then you can change the MTU size. The default MTU value is 1500 Bytes. It is not recommended that you change the default value unless required by your ISP. Enable NAT: This technology translates the IP addresses of a local area network to a different IP address for the Internet. If this Modem Router is hosting your networks connection to the Internet, please select the check box. If another Router exists in your network, you dont need to select the option. Enable Fullcone NAT: It is a type of NAT, if not enabled, the default NAT will act. Enable SPI Firewall: A SPI firewall enhances networks security. Select the option to use a firewall, or else without a firewall. Enable IGMP Proxy: IGMP (Internet Group Management Protocol) is used to manage multicasting on TCP/IP networks. Some ISPs use IGMP to perform remote configuration for client devices, such as the Modem Router. The default value is enabled, and if you are not sure, please contact your ISP or just leave it. Get IP Unicast: This is disabled by default. The minority of DHCP Server of ISP will not support to enable this. When the Route is connected right but IP cannot get, you can select this box. 25 TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Primary DNS Server/ Secondary DNS Server: Choose Set DNS Server manually, you can set DNS Server (at least one) manually here. The Route will use this DNS Server for priority. Click the Save button to save the settings. 4.4.1.3 PPPoE If your ISP provides a PPPoE connection and you need to use an ATM Interface, choose PPPoE in the drop-down list, and then the screen will be displayed as below. Figure 4-6 PPP Username/Password/Confirm Password: Enter the User Name, Password and Confirm Password provided by your ISP. These fields are case-sensitive. 26 TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Authentication Method: Select the Authentication Method from the drop-down list, the default method is AUTO_AUTH, and you can leave it as a default setting. Choose the right connection type according to your needs: For PPPoE connection, you can select Connect on demand or Connect automatically or Connect manually. Connect on demand is dependent on the traffic. If there is no traffic (or Idle) for a pre-specified period of time), the connection will tear down automatically. And once there is traffic send or receive, the connection will be automatically on. Click Advanced, advanced selections for WAN Service Setup can be shown. Service Name/Server Name: Enter the Service Name and Server Name if it was provided by your ISP. You can leave them blank, if the ISP doesnt provide them. 4.4.1.4 PPPoA If your ISP provides a PPPoA connection and you need to use an ATM Interface, choose PPPoA in the drop-down list, and then the screen will be displayed as below. The configuration is similar to PPPoE. Please refer to the section 4.4.14 PPPoE to configure this part. 27 TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Figure 4-7 4.4.1.5 IPoA If your ISP provides an IPoA connection, select IPoA option for the WAN service type on the screen. 28 TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Figure 4-8 IP Address/Subnet Mask: Enter the IP Address and Subnet Mask provided by ISP. If you forget, you can ask your ISP. DNS Server/Secondary DNS Server: Type in your preferred DNS server. Default Gateway: select a WAN Interface from the drop-down list as the IPv4 default gateway. 4.4.1.6 Bridge If you select this type of connection, the modem can be configured to act as a bridging device between your LAN and your ISP. Bridges are devices that enable two or more networks to communicate as if they are two segments of the same physical LAN. 29 TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Note:
After you finish the Internet configuration, please click Save to make the settings take effect. Figure 4-9 4.4.2 EWAN Choose NetworkEWAN, and you will see the Ethernet WAN Interface screen similar to Figure 4-10. There are there different configurations for the connection types, which are Dynamic IP, Static IP and PPPoE. You can select the corresponding types according to your needs. Note:
1) EWAN and DSL interface can not be used concurrently. If the EWAN Interface had configured, you cannot configure any other WAN service over the DSL Interface until the EWAN Interface is deleted. 2) If EWAN function is be enabled, LAN4/WAN port of the Modem Router changes to be WAN port which can be connected to the cable, VDSL or Fiber modem. 30 TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Figure 4-10 4.4.2.1 Dynamic IP Select this option, the Modem Router will be able to obtain IP network information dynamically from a DHCP server provided by your ISP (as shown Figure 4-10). The next configuration is similar to Dynamic IP over ATM interface (see section 4.4.1.2 Dynamic IP) 4.4.2.2 Static IP Select this option if your ISP provides static IP information to you and you want to use an Ethernet Interface. You should set static IP address, IP subnet mask, gateway address, DNS Server and Secondary DNS Server in the screen below. The next configuration is similar to Static IP for WAN Settings (see section 4.4.1.1 Static IP) 31 TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Figure 4-11 4.4.2.3 PPPoE If your ISP provides a PPPoE connection and you need to use an Ethernet Interface, select PPPoE option for the WAN service type on the screen. The following configuration is similar to PPPoE over ATM interface (see section 4.4.1.3 PPPoE). 32 TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Figure 4-12 4.4.3 Interface Grouping Choose NetworkInterface Grouping, you can view all the current groups on this page
(shown in Figure 4-13). Figure 4-13 33 TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide VLAN: Enable or disable this function. Virtual LAN (VLAN) is a group of devices on one or more LANs that are configured so that they can communicate as if they were attached to the same LAN, when in fact they are located on a number of different LAN segments. Because VLANs are based on logical instead of physical connections, it is very flexible for user/host management, bandwidth allocation and resource optimization. If you want to active this function, this function must be enabled. Note:
It is not allowed to disable the VLAN with Ethernet Connection enabled. To support this feature, you must create mapping groups with appropriate LAN and WAN interfaces using the Add button. The Remove button will remove the grouping and add the ungrouped interfaces to the Default group. Only the default group has IP interface. Click the Add button. You can add a new interface group in the next screen. For example, you want LAN1 and LAN3 to be a group called Group 1 over br_0_35_0 WAN interface, you can refer to the following figure. Click Save to make the entry effective immediately 4.4.4 LAN Settings Figure 4-14 Choose NetworkLAN Settings menu, and you will see the LAN screen (shown in Figure 4-15). Please configure the parameters for LAN ports according to the descriptions below. 34 TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Figure 4-15 IP Address: You can configure the Modem Routers IP Address and Subnet Mask for LAN Interface. IP Address: Enter the Modem Routers local IP Address, then you can access to the Web-based Utility via the IP Address, the default value is 192.168.1.1. Subnet Mask: Enter 255.255.255.0. the Modem Routers Subnet Mask, the default value is Enable IGMP Snooping: If you select the option, please choose the IGMP Mode: Standard Mode or Blocking Mode. Enable Second IP: You can configure the Modem Routers second IP Address and Subnet Mask for LAN Interface through which you can also access to the Web-based Utility as the default IP Address and Subnet Mask. DHCP Server: These settings allow you to configure the Modem Routers Dynamic Host Configuration Protocol (DHCP) server function. The DHCP server is enabled by default for the Modem Routers Ethernet LAN interface. DHCP service will supply IP settings to computers which are configured to automatically obtain IP settings that are connected to the Modem Router though the Ethernet port. When the Modem Router is set for DHCP, it becomes the default gateway for DHCP client connected to it. Keep in mind that if you change the IP address of the Modem Router, you must change the range of IP addresses in the pool used for DHCP on the LAN. Start IP Address: Enter a value for the DHCP server to start with when issuing IP addresses. Because the default IP address for the Modem Router is 192.168.1.1, the default Start IP Address is 192.168.1.100, and the Start IP Address must be 192.168.1.100 or greater, but smaller than 192.168.1.254. End IP Address: Enter a value for the DHCP server to end with when issuing IP addresses. The End IP Address must be smaller than 192.168.1.254. The default End IP Address is 192.168.1.254. 35 TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Leased Time: The Leased Time is the amount of time in which a network user will be allowed connection to the Modem Router with their current dynamic IP address. Enter the amount of time, in hours, then the user will be leased this dynamic IP address. After the dynamic IP address has expired, the user will be automatically assigned a new dynamic IP address. The default is 1440 minutes. The detailed configuration about DHCP server, please refer to section 4.5 DHCP Server. 4.4.5 MAC Clone Choose menu Advanced SetupMAC Clone, you can configure the MAC address of the WAN Interface as shown below. The WAN Interface List displays the Lay2 Interfaces you have configured on the section 4.4.1 WAN Settings, 4.4.2 Ethernet WAN and its default MAC Address. You can select corresponding WAN Interface from the drop-down list and click Clone button to clone your current PC MAC, and then click Save. Figure 4-16 Note:
Only the WAN Ports can use MAC Address Clone function. All the clone MAC addresses must not be the same with each other. 4.4.6 ALG Settings Choose menu Advanced SetupALG Settings, and then you can configure the basic security in the screen as shown in Figure 4-17. 36 TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Figure 4-17 Virtual Private Network (VPN) - VPN Passthrough must be enabled if you want to allow VPN tunnels using VPN protocols to pass through the Modem Router.
(PPTP) allows
- Point-to-Point Tunneling Protocol PPTP Passthrough the Point-to-Point Protocol (PPP) to be tunneled through an IP network. To allow PPTP tunnels to pass through the Modem Router, click Enable. L2TP Passthrough - Layer Two Tunneling Protocol (L2TP) is the method used to enable Point-to-Point sessions via the Internet on the Layer Two level. To allow L2TP tunnels to pass through the Modem Router, click Enable. IPSec Passthrough - Internet Protocol security (IPSec) is a suite of protocols for ensuring private, secure communications over Internet Protocol (IP) networks, through the use of cryptographic security services. To allow IPSec tunnels to pass through the Modem Router, click Enable. Application Layer Gateway (ALG) - It is recommended to enable Application Layer Gateway (ALG) because ALG allows customized Network Address Translation (NAT) traversal filters to be plugged into the gateway to support address and port translation for certain application layer "control/data" protocols such as FTP, TFTP etc. FTP ALG - To allow FTP clients and servers to transfer data across NAT, click Enable. TFTP ALG - To allow TFTP clients and servers to transfer data across NAT, click Enable. Click the Save button to save your settings. 4.4.7 DSL Settings Choose Advanced SetupDSL Settings, you can select the DSL Modulation Type and Annex Type in the next screen. The DSL feature can be selected when you meet the physical connection problem. Please check the proper settings with your Internet service provider. 37 TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Figure 4-18 DSL Modulation Type: Select the DSL operation Modulation Type which your DSL connection uses. Annex Type: Select the DSL operation Annex Type which your DSL connection uses. Click the Save button to save your settings. 4.5 DHCP Server Choose DHCP Server, you can see the next submenus:
Click any of them, and you will be able to configure the corresponding function. 4.5.1 DHCP Settings Choose menu DHCP ServerDHCP Settings, you can configure the DHCP Server on the page as shown in Figure 4-19.The Modem Router is set up by default as a DHCP (Dynamic Host Configuration Protocol) server, which provides the TCP/IP configuration for all the PC(s) that are connected to the Modem Router on the LAN. 38 TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Figure 4-19 Start IP Address: Enter a value for the DHCP server to start with when issuing IP addresses. Because the default IP address for the Modem Router is 192.168.1.1, the default Start IP Address is 192.168.1.100, and the Start IP Address must be 192.168.1.100 or greater, but smaller than 192.168.1.254. End IP Address: Enter a value for the DHCP server to end with when issuing IP addresses. The End IP Address must be smaller than 192.168.1.254. The default End IP Address is 192.168.1.254. Address Lease Time: The Leased Time is the amount of time in which a network user will be allowed connection to the Modem Router with their current dynamic IP address. Enter the amount of time, in hours, then the user will be leased this dynamic IP address. After the dynamic IP address has expired, the user will be automatically assigned a new dynamic IP address. The default is 24 hours. Default Gateway - (Optional): It is suggested to input the IP address of the LAN port of the Modem Router. The default value is 192.168.1.1. Default Domain - (Optional): Input the domain name of your network. Primary DNS - (Optional): Input the DNS IP address provided by your ISP or consult your ISP. Secondary DNS - (Optional): Input the IP address of another DNS server if your ISP provides two DNS servers. DHCP Relay: Select Relay, then you will see the next screen, and the Modem Router will work as a DHCP Relay. A DHCP relay is a computer that forwards DHCP data between computers that request IP addresses and the DHCP server that assigns the addresses. Each of the device's interfaces can be configured as a DHCP relay. If it is enabled, the DHCP requests from local PCs will forward to the DHCP server runs on WAN side. To have this function working properly, please run on router mode only, disable the DHCP server on the LAN port, and make sure the routing table has the correct routing entry. 39 TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Note:
1) To use the DHCP server function of the Modem Router, you must configure all computers on the LAN as "Obtain an IP Address automatically". 2) You have to disable NAT of the WAN connections, or the DHCP Relay may not take effect. 3) Click the Save button to save your settings. If you select Disabled, the DHCP function will not take effect. 4.5.2 Clients List Choose menu DHCP ServerClients List, you can view the information about the clients attached to the Modem Router in the screen as shown in Figure 4-20. Client Name: The name of the DHCP client MAC Address: The MAC address of the DHCP client Figure 4-20 IP Address: The IP address that the Modem Router has allocated to the DHCP client Valid Time: The time of the DHCP client leased. After the dynamic IP address has expired, a new dynamic IP address will be automatically assigned to the user. You cannot change any of the values on this page. To update this page and to show the current attached devices, click the Refresh button. 4.5.3 Address Reservation Choose menu DHCP ServerAddress Reservation, you can view and add a reserved address for clients via the next screen (shown in Figure 4-21).When you specify a reserved IP address for a PC on the LAN, that PC will always receive the same IP address each time when it accesses the DHCP server. Reserved IP addresses should be assigned to the servers that require permanent IP settings. 40 TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide MAC Address: The MAC address of the PC for which you want to reserve an IP address. Figure 4-21 IP Address: The IP address reserved for the PC by the Modem Router. Status: The status of this entry either Enabled or Disabled. To Reserve an IP address:
1. Click the Add New button. Then Figure 4-22 will pop up. 2. Enter the MAC address (in XX:XX:XX:XX:XX:XX format.) and IP address (in dotted-decimal notation) of the computer for which you want to reserve an IP address. 3. Click the Save button. Figure 4-22 To modify or delete an existing entry:
1. Click the Edit in the entry you want to modify. If you want to delete the entry, click the Delete. 2. Modify the information. 3. Click the Save button. Click the Enable/Disable Selected button to make selected entries enabled/disabled. Click the Delete Selected button to selected entries. 4.5.4 Conditional Pool Choose menu DHCP ServerConditional Pool, you can see the next screen (shown in Figure 4-23). This page displays vendor class settings and allows you to set parameters for vendor class by clicking corresponding buttons. 41 TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Figure 4-23 To add a vendor class:
1. Click the Add New button. Then Figure 4-24 will pop up. 2. Enter parameters for the vendor class. Click the Save button. Figure 4-24 To modify or delete an existing entry:
4. Click the Edit in the entry you want to modify. If you want to delete the entry, click the Delete. 5. Modify the information. 6. Click the Save button. Click the Enable/Disable Selected button to make selected entries enabled/disabled. Click the Delete Selected button to selected entries. 42 TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide 4.6 Wireless Choose Wireless, there are six submenus to configure Wireless LAN settings. Click any of them, and you will be able to configure the corresponding function. The detailed explanations for each submenu are provided below. 4.6.1 Basic Settings Choose WirelessBasic, you will see the screen of Wireless--Basic settings shown as below. The basic settings for wireless networking are set on this screen. Figure 4-25 This page allows you to configure basic features of the wireless LAN interface. You can enable or disable the wireless LAN interface, hide the network from active scans, set the wireless network name (also known as SSID) and restrict the channel set based on Region requirements. SSID: Wireless network name shared among all points in a wireless network. The SSID must be identical for all devices in the wireless network. It is case-sensitive and must not exceed 32 characters (use any of the characters on the keyboard). Make sure this setting is the same for all stations in your wireless network. Type the desired SSID in the space provided. Mode: Select the desired mode. 11b only: Select if all of your wireless clients are 802.11b. 11g only: Select if all of your wireless clients are 802.11g. 11n only: Select only if all of your wireless clients are 802.11n. 43 TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide 11bg mixed: Select if you are using both 802.11b and 802.11g wireless clients. 11bgn mixed: Select if you are using a mix of 802.11b, 11g, and 11n wireless clients. Select the desired wireless mode. When 802.11g mode is selected, only 802.11g wireless stations can be connected to the Modem Router. When 802.11n mode is selected, only 802.11n wireless stations can connect to the Modem Router. It is strongly recommended that you set the Mode to 802.11b&g&n, and all of 802.11b, 802.11g, and 802.11n wireless stations can connect to the Modem Router. Channel: Select the channel you want to use from the drop-down List of Channel. This field determines which operating frequency will be used. It is not necessary to change the wireless channel unless you notice interference problems with another nearby access point. Channel Width: Select the channel width from the drop-down list. The default setting is automatic, which can adjust the channel width for your clients automatically. Note:
If 11b only, 11g only, or 11bg mixed is selected in the Mode field, the Channel Width selecting field will turn grey and the value will become 20M, which is unable to be changed. Enable Wireless Router Radio: If you want to use wireless features, you must select Enable Wireless Router Radio. If you deselect Enable Wireless Router Radio option, all the Wireless settings below will be disabled. Enable SSID Broadcast: When wireless clients survey the local area for wireless networks to associate with, they will detect the SSID broadcast by the Modem Router. If you select the Enable SSID Broadcast checkbox, the Wireless Router will broadcast its name (SSID) on the air. Enable WDS: Check this box to enable WDS. With this function, the Modem Router can bridge two or more Wlans. If this checkbox is selected, you will have to set the following parameters as shown in the figure below. Make sure the following settings are correct. SSID (to be bridged): The SSID of the AP your Modem Router is going to connect to as a client. You can also use the search function to select the SSID to join. BSSID (to be bridged): The BSSID of the AP your Modem Router is going to connect to as a client. You can also use the search function to select the BSSID to join. Scan: Click this button, you can search the AP which runs in the current channel. Key type: This option should be chosen according to the AP's security configuration. It is recommended that the security type is the same as your AP's security type 44 TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide WEP Index: This option should be chosen if the key type is WEP(ASCII) or WEP(HEX). It indicates the index of the WEP key. Auth Type: This option should be chosen if the key type is WEP(ASCII) or WEP(HEX). It indicates the authorization type of the Root AP. Password: If the AP your Modem Router is going to connect needs password, you need to fill the password in this blank. Click Save to save your settings. 4.6.2 WPS Settings This section will guide you to add a new wireless device to an existing network quickly by WPS
(also called QSS) function. a). Choose menu WPS Settings, and you will see the next screen (shown in Figure 4-26 ). Figure 4-26 WPS: Enable or disable the WPS function here. Current PIN: The current value of the Modem Router's PIN is displayed here. The default PIN of the Modem Router can be found in the label or User Guide. Restore PIN: Restore the PIN of the Modem Router to its default. Gen New PIN: Click this button, and then you can get a new random value for the Modem Router's PIN. You can ensure the network security by generating a new PIN. Add device: You can add a new device to the existing network manually by clicking this button. b). To add a new device:
If the wireless adapter supports Wi-Fi Protected Setup (WPS), you can establish a wireless connection between wireless adapter and Modem Router using either Push Button Configuration
(PBC) method or PIN method. Note:
To build a successful connection by WPS, you should also do the corresponding configuration of the new device for WPS function meanwhile. I. Use the Wi-Fi Protected Setup Button Use this method if your client device has a Wi-Fi Protected Setup button. Step 1: Press the WPS button on the side panel of the Modem Router, as shown in the following figure. 45 TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide You can also keep the default WPS Status as Enabled and click the Add device button in Figure 4-26, then Choose Press the button of the new device in two minutes and click Connect.
(Shown in the following figure) Figure 4-27 Step 2: Press and hold the WPS button of the client device directly. Step 3: The Wi-Fi Protected Setup LED flashes for two minutes during the Wi-Fi Protected Setup process. Step 4: When the WPS LED is on, the client device has successfully connected to the Modem Router. Refer back to your client device or its documentation for further instructions. II. Enter the client devices PIN on the Modem Router Use this method if your client device has a Wi-Fi Protected Setup PIN number. Step 1: Keep the default WPS Status as Enabled and click the Add device button in Figure 4-26, then the following screen will appear. Figure 4-28 46 TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Step 2: Enter the PIN number from the client device in the field on the above WPS screen. Then Step 3:
click Connect button. Connect successfully will appear on the screen of Figure 4-28, which means the client device has successfully connected to the Modem Router. III. Enter the Modem Routers PIN on your client device Use this method if your client device asks for the Modem Routers PIN number. Step 1: On the client device, enter the PIN number listed on the Modem Routers Wi-Fi Protected Setup screen. (It is also labeled on the bottom of the Modem Router.) Step 2: The Wi-Fi Protected Setup LED flashes for two minutes during the Wi-Fi Protected Setup process. Step 3: When the WPS LED is on, the client device has successfully connected to the Modem Router. Step 4: Refer back to your client device or its documentation for further instructions. Note:
1) The WPS LED on the Modem Router will light green for five minutes if the device has been successfully added to the network. 2) The WPS function cannot be configured if the Wireless Function of the Modem Router is disabled. Please make sure the Wireless Function is enabled before configuring the WPS. 4.6.3 Wireless Security Choose menu Wireless Wireless Security, you can configure the security settings of your wireless network. There are three wireless security modes supported by the Modem Router: WEP (Wired Equivalent Privacy), WPA-PSK (Pre-Shared Key), WPA2-PSK (Pre-Shared Key). 47 TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Figure 4-29 Disable Wireless Security: If you do not want to use wireless security, check this radio button. But its strongly recommended to choose one of the following modes to enable security. WEP: It is based on the IEEE 802.11 standard. If you check this radio button, you will find a notice in red as show in Figure 4-29. Figure 4-30 Auth Type - you can choose the type for the WEP security on the drop-down list. The default setting is Automatic, which can select Shared Key or Open System authentication type automatically based on the wireless station's capability and request. WEP Key Format - Hexadecimal and ASCII formats are provided here. Hexadecimal format stands for any combination of hexadecimal digits (0-9, a-f, A-F) in the specified length. ASCII format stands for any combination of keyboard characters in the specified length. 48 TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide WEP Key - Select which of the four keys will be used and enter the matching WEP key that you create. Make sure these values are identical on all wireless stations in your network. Key Type - You can select the WEP key length (64-bit, or 128-bit, or 152-bit.) for encryption.
"Disabled" means this WEP key entry is invalid. 64-bit - You can enter 10 hexadecimal digits (any combination of 0-9, a-f, A-F, zero key is not promoted) or 5 ASCII characters. 128-bit - You can enter 26 hexadecimal digits (any combination of 0-9, a-f, A-F, zero key is not promoted) or 13 ASCII characters. 152-bit - You can enter 32 hexadecimal digits (any combination of 0-9, a-f, A-F, zero key is not promoted) or 16 ASCII characters. Note:
If you do not set the key, the wireless security function is still disabled even if you have selected Shared Key as Authentication Type. WPA-PSK /WPA2-PSK: Its based on Radius Server. Auth type - you can choose the version of the WPA security on the drop-down list. The default setting is Auto, which can select WPA (Wi-Fi Protected Access) or WPA2 (WPA version 2) automatically based on the wireless station's capability and request. Encryption - You can select either Auto, or TKIP or AES. PSK Password - You can enter ASCII characters between 8 and 63 characters or 8 to 64 Hexadecimal characters. Group Key Update Period - Specify the group key update interval in seconds. The value should be 30 or above. Enter 0 to disable the update. Be sure to click the Save button to save your settings on this page. 4.6.4 Wireless MAC Filtering Choose menu Wireless MAC Filtering, you can control the wireless access by configuring the Wireless MAC Filtering function, shown in Figure 4-31. Figure 4-31 To filter wireless users by MAC Address, click Enable. The default setting is Disabled. MAC Address: The wireless station's MAC address that you want to filter. Status: The status of this entry, either Enabled or Disabled. 49 TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Description: A simple description of the wireless station. To Add a Wireless MAC Address filtering entry, click the Add New button. The following page will appear, shown in Figure 4-32:
Figure 4-32 To add or modify a MAC Address Filtering entry, follow these instructions:
1. Enter the appropriate MAC Address into the MAC Address field. The format of the MAC is any hexadecimal digit). For example:
is XX:XX:XX:XX:XX:XX
(X Address 00:1D:0F:11:22:33. 2. Give a simple description for the wireless station in the Description field. For example:
Wireless station A. 3. Select Enabled or Disabled for this entry on the Status drop-down list. 4. Click the Save button to save this entry. To edit or delete an existing entry:
1. Click the Edit in the entry you want to modify. 2. Modify the information. 3. Click the Save button. Click the Enable/ Disabled Selected button to make selected entries enabled or disabled. Click the Delete Selected button to selected entries. For example: If you desire that the wireless station A with MAC address 00:1D:0F:11:22:33 and the wireless station B with MAC address 00:0A:EB:00:07:5F are able to access the Modem Router, but all the other wireless stations cannot access the Modem Router, you can configure the Wireless MAC Address Filtering list by following these steps:
1. Click the Enable button to enable this function. 2. Select the radio button Allow the stations specified by any enabled entries in the list to access for Filtering Rules. 3. Delete all or disable all entries if there are any entries already. 4. Click the Add New button. 1) Enter the MAC address 00:1D:0F:11:22:33/00:0A:EB:00:07:5F in the MAC Address field. 2) Enter wireless station A/B in the Description field. 3) Select Enabled in the Status drop-down list. 4) Click the Save button. 50 TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide 5) Click the Back button. The filtering rules that configured should be similar to the following list:
4.6.5 Wireless Advanced Choose menu WirelessWireless Advanced, you can configure the advanced settings of your wireless network. Figure 4-33 Transmit Power: Here you can specify the transmit power of Modem Router. You can select High, Middle or Low which you would like. High is the default setting and is recommended. Beacon Interval: Enter a value between 25-1000 milliseconds for Beacon Interval here. The beacons are the packets sent by the Modem Router to synchronize a wireless network. Beacon Interval value determines the time interval of the beacons. The default value is 100. RTS Threshold: Here you can specify the RTS (Request to Send) Threshold. If the packet is larger than the specified RTS Threshold size, the Modem Router will send RTS frames to a particular receiving station and negotiate the sending of a data frame. The default value is 2346. Fragmentation Threshold: This value is the maximum size determining whether packets will be fragmented. Setting the Fragmentation Threshold too low may result in poor network performance because of excessive packets. 2346 is the default setting and is recommended. DTIM Interval: This value determines the interval of the Delivery Traffic Indication Message
(DTIM). A DTIM field is a countdown field informing clients of the next window for listening to broadcast and multicast messages. When the Modem Router has buffered broadcast or multicast messages for associated clients, it sends the next DTIM with a DTIM Interval value. 51 TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide You can specify the value between 1-255 Beacon Intervals. The default value is 1, which indicates the DTIM Interval is the same as Beacon Interval. Enable Short GI: This function is recommended for it will increase the data capacity by reducing the guard interval time. Enabled Client isolation: This function can isolate wireless stations on your network from each other. Wireless devices will be able to communicate with the Modem Router but not with each other. To use this function, check this box. Client isolation is disabled by default. Enable WMM: WMM function can guarantee the packets with high-priority messages being transmitted preferentially. It is strongly recommended. Note:
If you are not familiar with the setting items in this page, it's strongly recommended to keep the provided default values; otherwise it may result in lower wireless network performance. 4.6.6 Wireless Status Choose menu WirelessWireless Status, you can see the MAC Address, Current Status, Received Packets and Sent Packets for each connected wireless station. Figure 4-34 MAC Address: The connected wireless station's MAC address Current Status: The connected wireless station's running status, one of STA-AUTH/
STA-ASSOC/ STA-JOINED/ WPA/ WPA-PSK/ WPA2/ WPA2-PSK/ AP-UP/ AP-DOWN/
Disconnected Received Packets: Packets received by the station Sent Packets: Packets sent by the station You cannot change any of the values on this page. To update this page and to show the current connected wireless stations, click on the Refresh button. 4.7 Voice Choose Voice, there are eight submenus under the main menu. Click any of them, and you will be able to configure the corresponding function. The detailed explanations for each submenu are provided below. 52 TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide 4.7.1 SIP Account Choose VoiceSIP Account, you will see the screen similar to Figure 4-35. SIP accounts are necessary for making VoIP calls. This section introduces how to setup the SIP(Session Initiation Protocol) account for your Modem Router. Figure 4-35 Profile Name: Displays the profile name of the account. Registrar Address: Displays the IP address or domin name of the SIP Registrar server. Phone Number: Displays the phone number of the account. Status: Displays the status of the account. Down means that the account has not been registered. Remove: Check the box and then click the Remove button below so that the very account will be deleted. Edit: Click the Edit button to modify the very account. To set up an SIP account, click the Add button in Figure 4-35. Configure the following parameters in Figure 4-36 and then click the Save button. Then an account is added. Please note that the blanks with red asterisk behind are required to be entered. 53 TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Figure 4-36 SIP Account Basic Profile Name: Assign a name to identify the profile. Please note that special characters are not allowed. Phone Number: Enter the phone number of the account you applied. Display Name: Assign a name for your account. This name is the Caller-ID you want to be displayed on your friends display panel, which can let your friend easily know who is calling. Please note that special characters are not allowed. Authentication ID: Enter the name or number used for SIP Authorization with SIP Registrar. This value is provided by your service provider. If its not provided, keep the default value. Password: This parameter, given by your service provider, holds the password used for authentication within VoIP SIP registrar. Registrar Address: Set the IP address of the SIP Registrar server, which is provided by your service provider. Registrar Port: Specify the port of the VoIP SIP registrar on which it will listen for register requests from VoIP device. SIP Proxy: Enter the SIP proxy if its provided, or keep the default value. SIP Proxy Port: Enter the SIP proxy port if its provided, or keep the default value. Outbound Proxy: Indicate the VoIP SIP outbound proxy server IP address. This parameter is very useful when VoIP device is behind a NAT, say the Modem Router you use connects to Internet by other device. Keep the default if its not provided by your service provider. Outbound Proxy Port: Specify the port of the VoIP SIP outbound proxy on which it will listen for messages. Keep the default value if its not provided by your service provider. SIP Account Advanced 54 TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Preferred Receive Ptime: Ptime, short for packet time, refers to the time interval for a voice packet to be sent by the remote caller. The unit is ms (millisecond). Usually the default value 20ms is OK. Priority: Select a priority for this account. This priority is useful when more than one account is added in this Modem Router. Incoming Call Route: Select which line the incoming VoIP call will be routed to. None: All incoming VoIP calls will be denied. Phone 1/Phone 2: The incoming call will be routed to either Phone1 or Phone 2 randomly. Idle: The incoming call will be routed to idle phone in priority. All: The incoming call will be routed to both Phone1 and Phone 2 synchronously. PSTN 2nd Stage Dial: The incoming call requires second stage dial. This function is applicable on the FXO ports that function as a bridge between VoIP call and PSTN. The user can remotely use the PSTN line to initial a call. MWI: MWI is short for Message Waiting Indicator. Enable this option, so there will be indications when voice message are received. Preferred Codec (1~4): Codec is known as Coder-Decoder which is used for data signal conversion. Each codec uses a different bandwidth and hence provides different levels of voice quality. The default codec settings are shown in the corresponding field for your reference. Preferred Codec1 owns the top priority. You can change the value if you are provided with this parameter; otherwise leave it default. 4.7.2 Dial Plan Choose VoiceDial Plan, you can see the next submenus:
This section includes Dial Plan List, Forbidden Call and Emergency call. The function allows users to set rules for outgoing calls. 4.7.2.1 Dial Plan List Choose VoiceDial Plan Dial Plan List, you will see the screen similar to Figure 4-37. Dial plan List allows the Modem Router to use specific defined account or network to make outgoing calls. Prefix number is the key to making a distinction between VoIP and PSTN call. If actual numbers dialed match prefix number defined in the dial plan, the dialed number will be routed to the specified network according to this plan. Besides, operation of stripping prefix, replacing prefix or adding prefix, is helpful for users to make a quick and easy call. 55 TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Figure 4-37 Prefix: Displays the prefix of your plan. This prefix refers to the initial digit(s) of the numbers you dial. Op: Displays the operation of this plan. Destination: Displays the account or network used for this plan. Enable: Displays the interface(s) enabled in this plan. Remove: Check the box and then click the Remove button below so that the very plan will be deleted. Edit: Click the Edit button to modify the very plan. To add a dial plan, click the Add button in Figure 4-37. Fill in the following parameters and click the Save button in Figure 4-38. Figure 4-38 Prefix: Set number(s) as the prefix. Up to 16 characters can be entered. Destination: Both SIP account and PSTN can be selected here. As to which one will be finally used, it depends on not only Destination selected here but also Dial Plan Priority configured on Phone Setup page. Please note that if you want to select a SIP account, you should first add one on SIP Account page; otherwise only NONE is available. Max Length: Specify the max length of numbers you wish to dial out. The length of the actual dialed number can not exceed the length set here. For example, if the length is set to 6, when you dial 7654321, only 765432 will be sent out. Dial End With: Ways of indicating when the dialing is finished. 56 TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide If TimeOut is selected, the dialing will be sent out when timeout starts. The timeout activates when no more digits are dialed in a specific duration;
If # is selected, the dialing will not be sent until # is dialed;
If #/TimeOut is selected, the dialing will be sent out when timeout starts or # is dialed;
If None is selected, the dialing will not be sent out unless the length of number you dial meets the Max Length. Operate: Specify a dialing method to make call(s). Strip Prefix If it is selected, the original phone number will be sent out with the prefix deleted; you can limit the strip length by entering digits in Strip Length field. Take the 1st dial plan in Figure 4-38 as an example. If you dial 12340000, number 40000 will be dialed out to make a call. Replace Prefix If it is selected, the original phone number will be sent out with the prefix replaced by what you set in the Replace With field. Take the 2nd dial plan in Figure 4-38 as an example. If you dial 186666, number 18655556666 will be dialed out to make a call. Add Number If it is selected, the original phone number will be sent out with what you set in Add Number field added ahead. Take the 3rd dial plan in Figure 4-38 as an example. If you dial 018655556666, number 1795101865555666 will be dialed out to make a call. Interface Enable: You can check any box to enable interface(s). Numbers matching prefix in DIal Plan List can only be dialed out through the selected interface(s). 4.7.2.2 Forbidden Call Choose VoiceDial Plan Forbidden Call, you will see the screen similar to Figure 4-39. Forbidden Call makes it possible for administrators to control user's access to the voice service. Figure 4-39 Prefix: Displays the prefix of your plan. This prefix refers to the initial digit(s) of the numbers you dial. Forbidden: Displays the interface(s) disabled in this plan. Remove: Check the box and then click the Remove button below so that the very plan will be deleted. Edit: Click the Edit button to modify the very plan. To add a dial plan, click the Add button in Figure 4-39. Fill in the following parameters and click the Save button in Figure 4-40. 57 TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Figure 4-40 Prefix: Set number(s) as the prefix. Up to 16 characters can be entered. Interface Barring: You can check any box to disable interface(s). Numbers matching prefix in Forbidden Call list are not allowed to be dialed out through the selected interface(s). For example, if you set a dial plan list in the screen as shown in Figure 4-40, phone numbers starts with 020 can only be dialed out through PSTN line. 4.7.2.3 Emergency Call Some emergency phone numbers (e.g. 911) can only be dialed out through PSTN line. This function can make sure emergency calls will be dialed out efficiently. Figure 4-41 Enable: Check the box to enable this function for the very number in the blank. Emergency Phone Number: Type in emergency phone numbers in the blank. Click the Save button to make the configuration take effect. 4.7.3 Phone Setup Choose VoicePhone Setup, you will see the screen similar to Figure 4-42. This section allows you to configure phone settings for phone 1 and phone 2. 58 TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Phone Enable: Check the box behind to enable the function. Figure 4-42 Dial Settings Dial Plan Priority: The parameters configured here determine which network or SIP account to use when making outgoing calls. In the 1st field, there are options of networks. Please note if no SIP account is set on SIP Account page, only PSTN network will be available. Otherwise networks available are VOIP, PSTN Preferred and PSTN. If the network selected is not PSTN, you need to choose a SIP account from the 2nd field. The following are different options:
VOIP & Auto The Router will always use VoIP network to make calls. As to the account, the one specified in the matched dial plan will be chosen first. Otherwise, the account with top priority will be selected. To view the priority, please go to the screen as shown in Figure 4-36. If Fallback to PSTN box is checked, the Router will try PSTN network to make calls after VoIP call fails. VOIP & Account X (a certain account) The Modem Router will always use VoIP network and Account X to make calls. If Fallback to PSTN box is checked, the Router will try PSTN network to make calls after VoIP call fails. PSTN Preferred & Auto The Router will select the PSTN network and VoIP account to make calls according to your dial plans set on Dial Plan page. If no dial plan is matched with your outgoing call, then PSTN network will be automatically selected. 59 TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide PSTN Preferred & Account X (a certain account) The Router will select the network to make calls according to your dial plans set on Dial Plan page. If VoIP network is selected, the account used will be Account X. But if no dial plan is matched with your outgoing call, then PSTN network will be automatically selected. PSTN The Modem Router will always use PSTN network disregarding your dial plans on Dial Plan page. End With #': Choose whether to use # as the end signal of your dialing or not. Anonymous Calling: Hide the own phone number for each call and it will not be displayed on the remote site. This feature is only available for VoIP calls and disabled by default. Dial Restriction: Choose the pull-down menu to set restriction for outgoing calls. None: Allow all numbers to be dialed out. All: Forbid all numbers to be dialed out. According to Forbidden Call: Numbers will be dialed out according to settings in Forbidden Call. WarmLine Enable: Check the box to enable WarmLine function. So if there is no dialing action after you pick up the phone set, after the warmline time the phone will dial out automatically with the numbers set in Warmline Number. WarmLine Time: Choose WarmLine Time from the drop-down list to specify an interval before the phone dials out automatically. Warmline Number: Click View/Set button to view or set Warmline Number. Note:
Only numbers of VoIP calls are available here by default. However, if your PSTN service provider supports polarity reversal and you have applied for it, please check the box before PSTN polarity reversal support in Figure 4-43 then you can set PSTN call numbers here. Answer Settings MWI Mode: Options available are VMWI and CLID. If you don't know, please consult your service provider. Anonymous Call Blocking: Check the box to deny anonymous incoming calls. DND(Do not disturb): Check the box to deny all incoming calls. Call Waiting: Check the box to enable this function. When the line is busy, the incoming call will be indicated to wait. Forward Unconditionally: If the box behind is checked, all the incoming calls will be forwarded to the number set before @ through selected account. Please note that network or account available here varies with that in Dial Plan Priority field. Forward On "busy": Check the box to enable this function. When the line is busy, all the incoming calls will be forwarded to the number set before @ through selected account. Please note that network or account available here varies with that in Dial Plan Priority field. Forward On "no answer"& "No answer" time: Check the box to enable this function. When there is no answer, all the incoming calls will be forwarded to the number set before @
60 TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide through selected account when "No answer" time is out. Please note that network or account available here varies with that in Dial Plan Priority field. Telephony Settings VAD Support: VAD(Voice Activation Detection) prevents transmitting the silence packets to consume the bandwidth. It is also known as Silence Suppression which is a software application that ensures the bandwidth is reserved only when voice activity is activated. It is enabled by default. Speaker Gain: Sound Volume control of speaker. Mic Gain: Sound Volume control of microphone. 4.7.4 Advanced Setup Choose VoiceAdvanced Setup, you will see the next screen in Figure 4-43. Figure 4-43 SIP Advanced Setup:
Bound Interface Name: Bound Interface decides where to send/receive the VOIP traffic. Easy way to select the interface is to check the location of the SIP server. If it locates some where in the Internet then select Any_WAN. If it is on the local network then select LAN. Locale Selection: Select a country where you are located. The Router is embedded with some default parameters according to different countries such as ring tones. 61 TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide DSCP for SIP/RTP: DSCP(Differentiated Services Code Point) is the first 6 bits in the ToS byte. DSCP marking allows users to assign specific application traffic to be executed in priority by the next Router based on the DSCP value. Select DSCP for the SIP(Session Initiation Protocol) and RTP(Real-time Transport Protocol) respectively. If you are unsure, please always keep the default value. Dtmf Relay setting: DTMF is Dual Tone Multi Frequency. Options available are SIPInfo, RFC2833, and InBand. If you are unsure which one to choose, please always keep the default value. SIPInfo If it is selected, the Router will capture the DTMF tone and transfer it into SIP form. Then it will be sent to the remote end with SIP message. RFC2833 If it is selected, the Router will capture the keypad number you pressed and transfer it into digital form then send to the other side; the receiver will generate the tone according to the digital form it receives. This function is very useful when the network traffic congestion occurs and it still can remain the accuracy of DTMF tone. InBand If it is selected, the Router will send the DTMF tone as audio directly when you press the keypad on the phone. Registration Expire Timeout(s): Expire time for the registration message sending. Registration Retry Interval(s): Set the time duration for your SIP Registrar server to keep your registration record. Before the time expires, the Modem Router will send another register request to SIP Registrar again. If you are unsure of it, please always keep the default value. Enable T38 support: T38 specifies a protocol for transmitting a fax across IP network in real time. It allows the transfer of fax documents in real-time between two standard Group 3 facsimile terminals over the Internet or other networks using IP protocols. It will only function when both sites support this feature and are enabled. PSTN Setup Incoming PSTN Calls Routing: Choose a method for the Router to decide where to route the incoming call on PSTN network. Phone-Physical Phone The Router will route the incoming call according to the physical line selected in Route Incoming PSTN Calls To field. For example, if Idle Phone is selected, the Router will first judge the status of Phone 1. If it is free, then the incoming call will be routed to Phone 1. Otherwise, the Router will go on judging the status of Phone 2. VoIP-VoIP call The Router will route the incoming call according to the SIP number and account set in SIP URI of PSTN endpoint field. For example, if 2654321@test1 is input, the Router will directly route the incoming call to 2654321 through test1. The SIP number and account can be a remote one, say a friends SIP number and account. Besides, VoIP-VoIP call allows second dialing when the SIP number but not account is left blank, for example @test1. This function is applicable on the FXO ports that function as a bridge between VoIP call and PSTN. The user can remotely use the VoIP line to initial a call. PSTN polarity reversal support: This feature is disabled by default. If you are unsure of it, please always keep the default. 62 TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide 4.7.5 Speed Dial Choose VoiceSpeed Dial, you will see the screen as shown in Figure 4-44. This section introduces how to configure Speed Dial for your account. Speed Dial function can help to store frequently used telephone numbers and make your dial more convenient. It allows you to make a call by pressing a short number and the pound sigh # on the phone keypad instead of the original number. To add a Speed Dial entry, click the Add button and you will see the screen as shown in Figure 4-45. Fill in the following parameters and then click the Save button. Figure 4-44 Figure 4-45 Number: Enter a phone number. Speed Dial: Enter a number from 0~99. Click the Save button, you will go back to the previous page and see the following list as shown in Figure 4-46. Figure 4-46 Click the Save button to make the configuration take effect. If you want to delete the entry, check the Remove box first, and then click the Remove button. 4.7.6 Call Log Choose VoiceCall Log, you will see the screen as shown in Figure 4-47. This function allows you to view call logs and configure call log options. 63 TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Figure 4-47 Call Log: Check the Enable if you want to make this function take effect; otherwise check the Disable. Start: Beginning time of the call. Source: Caller ID, either phone number or IP address. Dest: Callee ID, either phone number or IP address. Type: Call types, including Incoming (VoIP), Incoming (PSTN), Outgoing (VoIP) and Outgoing (PSTN). Process: Process types, including Connected, Local forward, Remote forward, Local transfer, Remote transfer, Conference and Unconnected. Time: Total call time. To configure the view of call log, click the Config button and you will see the screen as shown in Figure 4-48. This page displays all the call types and process types. You can choose some of them or all of them. Check the boxes before the corresponding options which you desire to view and click the Save button to make the configuration take effect. Figure 4-48 4.7.7 Call Firewall Choose VoiceCall Firewall, you can see the next submenus:
64 TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Call Firewall can be used to control incoming calls. This section introduces how to configure the Call Firewall. Choose VoiceCall FirewallMode Setting, you will see the screen as shown in Figure 4-49. Figure 4-49 Call Firewall Enable: Check the box if you want to make the Call Firewall take effect. Black: Check the Black box to enable Black List mode. Calls from numbers placed in the Black List will be denied. White: Check the White box to enable White List mode. Only calls from numbers placed in the White List will be allowed. RejectAll: Check the RejectAll box to enable Reject All mode. All incoming calls will be denied. To configure the Black List, choose Voice Call FirewallBlack List on the left menu or click the Black List button on screen as shown in Figure 4-49, you will see the screen as shown in Figure 4-50. To add a new entry, click the Add button and you will see the screen as shown in Figure 4-51. Figure 4-50 65 TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Figure 4-51 Enter a number with the length in the range of [3, 16]in the field of Black List Number and Click the Save button to make the configuration take effect, then you will go back to the previous page and see the following list as shown in Figure 4-50. If you want to delete the entry, check the Remove box first and then click the Remove button. To configure the White List, choose Voice Call Firewall White List on the left menu or click the White List button on the screen as shown in Figure 4-49, then you will see the screen as shown in Figure 4-52. To add a new entry, click the Add button and you will see the screen as shown in Figure 4-53. Figure 4-52 Figure 4-53 Enter a number with the length in the range of [3, 16] in the field of White List Number and click the Save button to make the configuration take effect, then you will go back to the previous page and see the following list as shown in Figure 4-52. If you want to delete the entry, check the Remove box first and then click the Remove button. Note:
1. Partial matching rule is applied here, so this function works for all the incoming call numbers that start with the number you have configured in the Black List or the White List. For example, if the number you have configured in the Black List is 555, with Black List mode enabled the incoming call number 5554510 will be denied. 2. If the numbers set in Black List and White List overlaps with each other, longest matching rule will function in this situation. That is, with Black List mode enabled, incoming call numbers that start with the number set in Black List may be allowed, and vice versa. For example, if you set 222 66 TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide in Black List and 2224 in White List, with Black List mode enabled, incoming call number 2224510 will be allowed. 4.7.8 USB Voice Mail Choose VoiceUSB Voice Mail, you will see the screen as shown in Figure 4-54. USB Voice mail is used to record voice messages when the call is not answered. To use this function, please make sure an external USB hard drive/USB flash disk with configure files has been plugged into the USB port on the Modem Router. For details about how to configure USB devices for USB Voice Mail function, please refer to Quick Installation Guide or T5 in Appendix B:
Troubleshooting. Figure 4-54 Phone: Displays the phone that has voice message. Source: Displays the source of the voice message, i.e. the remote caller account. Dest: Displays the destination of the voice message, i.e. the local account. Start Time: Displays when the voice message starts. Length: Displays how long the voice message is. Audition: Click Play to listen to the voice message. Read Flag: Displays whether the voice message has been read or not. Selected: Check the box to select the corresponding voice message. To refresh the web page, click Refresh button. To delete a voice message, check the Selected box and then click Remove button. To configure the USB Voice Mail, click Config button to enter the web page as shown in Figure 4-55. 67 TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Figure 4-55 Enable Local Play Operation Notify: Check this box so there will be sound indication for operation when you listen to the voice messages. This is enabled by default. If you are very familiar with the operations, you can disable it. Enable Global Wav Format: Check this box and all the voice message will be saved as wav files in your USB device. It is convenient for users to listen to the voice messages on the computer. Considering the capacity of your USB device, it is disabled by default. Enable Remove Expired Voice: Check this box and then the expired voice messages will be deleted automatically. Considering the capacity of USB device, it is enabled by default. Expired Days(7~15): Configure the days that you want the voice messages to be kept. Voice Duration Limit(20~120s): This option is used to limit the duration of a voice message. USB MailBox Capacity: Set the capacity for the USB mailbox. Please note that the capacity set should be less than that of the USB device. Phone Enable: Check the box to enable this function. Phone Mode: If no answer is selected, voice notification will be played when there is no answer. If unconditionally is selected, all incoming calls will be directed to voice mail. Customize Voice Notify For Record: Check the box to enable voice notification customization. To record your own voice notification, press *30 after picking up your phone set. Voice Notify For Record: Select to use the default or customized voice notification. Remote Access PIN: This PIN code is used to listen to the voice messages in a remote place. Operations are as follows. 1) Call the local phone and wait for the voice notification. 2) Press * before the notification is over. 68 TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Input the PIN code according to the notification. 3) 4) You can listen to all the new messages after the PIN code is validated. Click Save to save your configurations. Click Back to go back to the previous page, i.e. Figure 4-54. 4.8 USB Settings There are six submenus under the USB Settings menu, USB Mass Storage, User Accounts, Storage Sharing, FTP Server, Media Server and Print Server. Click any of them, and you will be able to configure the corresponding function. 4.8.1 USB Mass Storage Choose menu USB Settings USB Mass Storage, you can configure a USB disk drive attached to the Modem Router and view volume and share properties such as share name, capacity, status, and action, etc on this page as shown below. Volume: The volume name of the USB drive the users have access to. File System: The system of the USB drive. Figure 4-56 69 TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Capacity: The storage capacity of the USB driver. Status: Indicates the shared or non-shared status of the volume. Active means volume can be shared, while Inactive means volume can not be shared. If Deactivate in Action field is enabled, Inactive will be displayed in the Status field, which means volume can not be shared. Action: When the volume is shared, you can click the Deactivate to stop sharing the volume;
when volume is non-shared, you can click the Activate button to share the volume. Click Disconnect to safely remove the USB storage device that is connected to USB port. Note:
Before removing the USB storage device, you should click Disconnect to make sure that all your data have been saved completely. Removing device directly may cause your USB storage device crashed. 4.8.2 User Accounts You can specify the user name and password for Storage Sharing and FTP Server users on this page. Storage Sharing users can access the folders by entering the following URL into the address field of your browser or Windows Explorer, such as \\192.168.1.1. FTP Server users can log into the FTP Server via FTP Client. There are five users here, which provide means to control the access to the USB mass storage by Storage Sharing or FTP. The Super User has the right to read and write to Storage Sharing and FTP Server. Figure 4-57 To add a new user account, please follow the steps below:
1. Choose the index from the drop-down list of Choose Index. 2. Self-define a New User Name. 3. Enter the password in the New Password field. 70 TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide 4. Re-enter the password in the Confirm Password field. 5. Click the Set button, and then a new entry will be added in the table. 6. Click the Apply button to apply your settings. Click the Refresh button to refresh this page immediately. 4.8.3 Storage Sharing Choose menu USB Settings Storage Sharing, you can configure a USB disk drive attached to the Modem Router and view volume and share properties on this page as shown below. Figure 4-58 Server Status: Indicates the Storage Sharing's current status. Anonymous access to all the volumes: If this function is enabled, users can access all activated volumes of Storage Sharing without accounts. Share Name: This folder's display name. Directory: The real full path of the specified folder. User Access: The authorization of the user is displayed. * users mean Super Users who have the full-access permission to all activated volumes and share folders. Grey users mean the users who have no right to use this function. Others are common users. Status: The status of the entry is enabled or disabled. Edit: Click Edit in the table, and then you can modify the entry. To add a new folder, follow the instructions below. 1. Click Add New Folder in Figure 4-58. 71 TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Figure 4-59 2. Click the Browse button, and then select the Select Volume from the drop-down list. 3. Enter display name of the share folder in Share Name filed. 4. Click the Apply button to apply the settings. You can click the upper button to go to the upper folder Click the Enable/Disable Selected button to enable or disable the selected entries. Click the Delete Selected button to delete the selected entries. Note:
1. The max share folders number is 10. If you want to share a new folder when the number has reached 10, you can delete an existing share folder and then add a new one. If you want to change the Storage Sharing settings, you can click the Apply button to make the changes take effect. 2. 4.8.4 FTP Server Choose menu USB SettingsFTP Server, you can create an FTP server that can be accessed from the Internet or your local network. 72 TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Figure 4-60 Internet Access: Enable or disable this function. Internet Address: If Internet Access is enabled, WAN IP will be displayed here. Server Status: Indicates the FTP Server's current status. Service Port: Enter the FTP Port number to use. The default is 21. Share Name: This folder's display name. Directory: The real full path of the specified folder. User Index: The authorization of the user is displayed. Status: The status of the entry is enabled or disabled. Edit: Click Edit in the table, and then you can modify the entry. To add a new folder, follow the instructions below. 1. Click Add New Folder in Figure 4-74. 73 TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Figure 4-61 2. Click the Browse button, and then select the Select Volume from the drop-down list. 3. Enter display name of the share folder in Share Name filed. 4. Click the Apply button to apply the settings. You can click the upper button to go to the upper folder. Click the Enable/Disable Selected button to enable or disable the selected entries. Click the Delete Selected button to delete the selected entries. Note:
1. The max share folders number is 10. If you want to share a new folder when the number has reached 10, you can delete an existing share folder and then add a new one. If you want to change the FTP settings, you can click the Apply button to make the changes take effect. 2. 4.8.5 Media Server Choose menu USB SettingsMedia Server, you can create media server that allows you to share stored content with other computers and devices on your home network and on the Internet. Figure 4-62 74 TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Server Enable: Select this box to enable this function. Server Name: The name of this Media Server. To add a new share folder for your media server, please follow the instructions below:
a) Click Add New Folder button, and you will see the screen as shown in Figure 4-77. b) Enter the name of the share folder in Share Name field. c) Click the Apply button to apply the configuration. Figure 4-63 b) Click the Scan now to scan all the share folders immediately. You can also select the Auto-scan, at same time, select an auto scan interval time by drop-down list. In this case, the media server will auto scan the share folders. Note:
The max share folders number is 6. If you want share a new folder when the numbers has been reached to be 6, you can delete a share folder and then add a new one. 4.8.6 Print Server Choose menu USB SettingsPrint Server, you can configure print server on this page as shown below. Figure 4-64 There are three states of the print server, they are as follows:
Online: Indicates the print service has been turned on, and no user is using the print services at present. You can click the "Stop" button to stop the print service. Offline: Indicates the print service feature is disabled. You can click "Start" button to start the print service. Busy: Indicates the print service has been turned on, but at this moment other users are using print services. 75 TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide 4.9 Route Settings Choose Route Settings, it includes three menus: Default Gateway, Static Route and RIP Settings. The detailed descriptions are provided below. 4.9.1 Default Gateway Choose Route SettingsDefault Gateway, you can see the Default Gateway screen. You can select a WAN Interface from the drop-down list as the system default gateway. Click the Add Interface button, you can add WAN Interfaces. Click the Save button to save your settings. Figure 4-65 4.9.2 Static Route Choose Route Settings Static Route. You can see the Static Route screen, this screen allows you to configure the static routes (shown in Figure 4-66). A static route is a pre-determined path that network information must travel to reach a specific host or network. Figure 4-66 To add static routing entries:
1. Click the Add New button in Figure 4-66, and you will see the screen as shown in Figure 4-67. 76 TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Figure 4-67 2. Enter the following data:
Destination IP Address: The Destination IP Address is the address of the network or host that you want to assign to a static route. Subnet Mask: The Subnet Mask determines which portion of an IP Address is the network portion, and which portion is the host portion. Gateway: Here you should type the Gateway address correctly, and the option for Interface will adopt the default Gateway address for the Static Route. Interface: Select the Interface name in the text box, or else, the default Use Interface will be adopted for the Static Route. Status: Select Enabled or disabled from the drop-down list. 3. Click Save to save your settings as shown in Figure 4-67. To modify or delete an existing entry:
1. Find the desired entry in the table. 2. Click Edit as desired on the Edit column. Click the Enable/ Disabled Selected button to make selected entries enabled/ disabled. Click the Delete Selected button to delete selected entries. 4.9.3 RIP Settings Choose Route SettingsRIP Settings, you can see the RIP (Routing Information Protocol) screen which allows you to configure the RIP. Figure 4-68 77 TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Note:
RIP cannot be configured on the WAN Interface which has NAT enabled (such as PPPoE). 4.10 Forwarding There are four submenus under the Forwarding menu: Virtual Servers, Port Triggering, DMZ and UPnP. Click any of them, and you will be able to configure the corresponding function. 4.10.1 Virtual Servers Choose menu Forwarding Virtual Servers, and then you can view and add virtual servers in the next screen (shown in Figure 4-69). Virtual servers can be used for setting up public services on your LAN. A virtual server is defined as a service port, and all requests from Internet to this service port will be redirected to the computer specified by the server IP. Any PC that was used for a virtual server must have a static or reserved IP address because its IP address may change when using the DHCP function. Figure 4-69 Service Port: The numbers of External Service Ports. You can enter a service port or a range of service ports (the format is XXX YYY; XXX is the Start port and YYY is the End port). IP Address: The IP address of the PC running the service application. Protocol: The protocol used for this application, either TCP, UDP, or All (all protocols supported by the Modem Router). Status: The status of this entry, "Enabled" means the virtual server entry is enabled. Edit: To modify or delete an existing entry. To setup a virtual server entry:
1. Click the Add New button. (pop-up Figure 4-70) 78 TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide 2. Select the service you want to use from the Common Service Port list. If the Common Service Port menu does not list the service that you want to use, enter the number of the service port or service port range in the Service Port field. 3. Select the service you want to use from the Use Interface list. 4. Enter the IP address of the computer running the service application in the IP Address field. 5. Select the protocol used for this application in the Protocol drop-down list, either TCP, UDP, or All. 6. Select the Enabled option in the Status drop-down list. Click the Save button. Figure 4-70 Note:
It is possible that you have a computer or server that has more than one type of available service. If so, select another service, and type the same IP address for that computer or server. To modify or delete an existing entry:
1. Find the desired entry in the table. 2. Click Edit as desired on the Edit column. Click the Enable/ Disabled Selected button to make selected entries enabled/ disabled. Click the Delete Selected button to delete selected entries. Note:
If you set the service port of the virtual server as 80, you must set the Web management port on System Tools > Remote Management page to be any other value except 80 such as 8080. Otherwise there will be a conflict to disable the virtual server. 4.10.2 Port Triggering Choose menu ForwardingPort Triggering, you can view and add port triggering in the next screen (shown in Figure 4-71). Some applications require multiple connections, like Internet games, video conferencing, Internet telephoning and so on. Port Triggering is used for some of these applications that cannot work with a pure NAT Modem Router. 79 TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Figure 4-71 To add a new rule, follow the steps below. 1. Click the Add New button, the next screen will pop-up as shown in Figure 4-72. 2. Select a common application from the Common Service Port drop-down list, then the Trigger Port field and the Open Ports field will be automatically filled. If the Common Service Port do not have the application you need, enter the Trigger Port and the Open Ports manually. 3. Select the protocol used for Trigger Port from the Trigger Protocol drop-down list, either TCP, UDP, or All. 4. Select the protocol used for Incoming Ports from the Incoming Protocol drop-down list, either TCP or UDP, or All. 5. Select Enable in Status field. 6. Click the Save button to save the new rule. Figure 4-72 Trigger Port: The port for outgoing traffic. An outgoing connection using this port will trigger this rule. Trigger Protocol: The protocol used for Trigger Ports, either TCP, UDP, or All (all protocols supported by the Modem Router). Open Port: The port or port range used by the remote system when it responds to the outgoing request. A response using one of these ports will be forwarded to the PC which triggered this rule. You can input at most 5 groups of ports (or port sections). Every group of ports must be separated with ",", for example, 2000-2038, 2046, 2050-2051, 2085, 3010-3030. 80 TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Open Protocol: The protocol used for Incoming Port, either TCP, UDP, or ALL (all protocols supported by the Modem Router). Status: The status of this entry, Enabled means the Port Triggering entry is enabled. Modify: To modify or delete an existing entry. Common Service Port: Some popular applications already listed in the drop-down list of Open Protocol. To modify or delete an existing entry:
1. Find the desired entry in the table. 2. Click Edit as desired on the Edit column. Click the Enable/ Disabled Selected button to make selected entries enabled/ disabled. Click the Delete Selected button to delete selected entries. Once the Modem Router is configured, the operation is as follows:
1. A local host makes an outgoing connection to an external host using a destination port number defined in the Trigger Port field. 2. The Modem Router records this connection, opens the incoming port or ports associated with this entry in the Port Triggering table, and associates them with the local host. 3. When necessary, the external host will be able to connect to the local host using one of the ports defined in the Incoming Ports field. Note:
1. When the trigger connection is released, the corresponding opened ports will be closed. 2. Each rule can only be used by one host on the LAN at a time. The trigger connection of other hosts on the LAN will be refused. 3. Open Ports ranges cannot overlap each other. 4.10.3 DMZ Choose menu ForwardingDMZ, and then you can view and configure DMZ host in the screen
(shown in Figure 4-73).The DMZ host feature allows one local host to be exposed to the Internet for a special-purpose service such as Internet gaming or videoconferencing. The Modem Router forwards packets of all services to the DMZ host. Any PC whose port is being forwarded must have its DHCP client function disabled and should have a new static IP Address assigned to it because its IP Address may be changed when using the DHCP function. 81 TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Figure 4-73 To assign a computer or server to be a DMZ server:
1. Click the Enable button. 2. Enter the IP address of a local PC that is set to be DMZ host in the DMZ Host IP Address field. 3. Click the Save button. 4.10.4 UPnP Choose menu ForwardingUPnP, and then you can view the information about UPnP in the screen (shown in Figure 4-74). The Universal Plug and Play (UPnP) feature allows the devices, such as Internet computers, to access the local host resources or devices as needed. UPnP devices can be automatically discovered by the UPnP service application on the LAN. Figure 4-74 Current UPnP Status: UPnP can be enabled or disabled by clicking the Enable or Disable button. This feature is enabled by default. Current UPnP Settings List: This table displays the current UPnP information. App Description: The description about the application which initiates the UPnP request. External Port: The port which the Modem Router opened for the application. Protocol: The type of protocol which is opened. Internal Port: The port which the Modem Router opened for local host. IP Address: The IP address of the local host which initiates the UPnP request. Status: Either Enabled or Disabled. "Enabled" means that the port is still active;
otherwise, the port is inactive. Click the Enable button to enable UPnP. 82 TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Click the Disable button to disable UPnP. Click the Refresh button to update the Current UPnP Settings List. 4.11 Parental Control Choose menu Parental Control, and you can configure the parental control in the screen as shown in Figure 4-75. The Parental Control function can be used to control the internet activities of the child, limit the child to access certain websites and restrict the time of surfing. Figure 4-75 Enable Parental Control: Check the box if you want this function to take effect. This function is disabled by default. MAC Address of Parental PC: In this field, enter the MAC address of the controlling PC, or you can make use of the Copy To Above button below. 83 TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide MAC Address of Current PC: This field displays the MAC address of the PC that is managing this Modem Router. If the MAC Address of your adapter is registered, you can click the Copy To Above button to fill this address to the MAC Address of Parental PC field above. Add URL: Here you can input the net addresses which the child is allowed to access. Click the Save button to save your settings. 4.12 Firewall There are four submenus under the Firewall menu: Rule, LAN Host, WAN Host and Schedule. Click any of them, and you will be able to configure the corresponding function. 4.12.1 Rule Choose menu Firewall Rule, and then you can view and set Access Control rules in the screen as shown in Figure 4-76. Figure 4-76 Enable Firewall: Select the check box to enable the Firewalll function, so the Default Filtering Rules can take effect. Description: Here displays the description of the rule and this name is unique. LAN Host: Here displays the host selected in the corresponding rule. Target: Here displays the target selected in the corresponding rule. Schedule: Here displays the schedule selected in the corresponding rule. Status: Here displays the status of the rule, enabled or not. Edit: Here you can edit or delete an existing rule. 84 TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Add New: Click the Add New button to add a new rule entry. Enable Selected: Click the Enable Selected button to enable the selected rules in the list. Disable Selected: Click the Disable Selected button to disable the selected rules in the list. Delete Selected: Click the Delete Selected button to delete the selected entries in the table. The methods to add a new rule:
1. Click the Add New button and the next screen will pop up as shown in Figure 4-77. 2. Give a name (e.g. Rule_1) for the rule in the Description field. 3. Select a host from the LAN Host drop-down list or choose Add LAN Host. 4. Select a target from the WAN Host drop-sown list or choose Add WAN Host. 5. Select a schedule from the Schedule drop-down list or choose Add Schedule. 6. 7. 8. 9. In the Action field, select Deny or Allow to deny or allow your entry. In the Status field, select Enabled or Disabled to enable or disable your entry. In the Direction field, select IN or OUT from the drop-down list for the direction. In the Protocol field, here are four options, All, TCP, UDP, and ICMP. Select one of them from the drop-down list for the target. 10. Click the Save button. Figure 4-77 4.12.2 LAN Host Choose menu Firewall LAN Host, and then you can view and set a Host list in the screen as shown in Figure 4-78. Figure 4-78 85 TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Description: Here displays the description of the host and this description is unique. Address Info: Here displays the information about the host. It can be IP or MAC. Edit: To modify an existing entry. To add a new entry, please follow the steps below. 1. Click the Add New button. 2. In the Mode field, select IP Address or MAC Address. If you select IP Address, please follow the steps below:
1) In Description field, create a unique description for the host (e.g. Host_1). 2) In IP Address field, enter the IP address. If you select MAC Address, please follow the steps below:
1) In Description field, create a unique description for the host (e.g. Host_1). 2) In MAC Address field, enter the MAC address. 3. Click the Save button to complete the settings. Click the Delete Selected button to delete the selected entries in the table. 4.12.3 WAN Host Choose menu Firewall WAN Host, and then you can view and set a Host list in the screen as shown in Figure 4-79. Figure 4-79 Description: Here displays the description about the WAN and this description is unique. Details: The details can be IP address, port, or domain name. Edit: To modify an existing entry. To add a new entry, please follow the steps below. 1. Click the Add New button. 2. If you select IP Address, the screen shown is Figure 4-80. In Mode field, select IP Address, MAC Address or URL Address. 86 TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Figure 4-80 In Description field, create a unique description for the host (e.g. Host_1). In IP Address field, enter the IP address. 1) 2) If you select MAC Address, the screen shown is Figure 4-81. Figure 4-81 In Description field, create a unique description for the host (e.g. Host_1). In MAC Address field, enter the MAC address. 1) 2) If you select URL Address, the screen shown is Figure 4-82. Figure 4-82 In Description field, create a unique description for the host (e.g. Host_1). 1) 2) Enter the URL address in the Add URL Address field, and then click the Add button. The URL address will be shown in the Detail table. If you click the Delete button, the existing URL address in the Detail table can be deleted. 3. Click the Save button to complete the settings. 87 TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide 4.12.4 Schedule Choose menu Firewall Schedule, and then you can view and set a Schedule list in the next screen as shown in Figure 4-83. Figure 4-83 Description: Here displays the description of the schedule and this description is unique. Edit: Here you can modify an existing schedule. To add a new schedule, follow the steps below:
1. Click Add New button and the next screen will pop-up as shown in Figure 4-84. 2. 3. 4. In Description field, create a unique description for the schedule (e.g. Schedule_1). In Apply To field, select the day or days you need. In time field, you can select all day-24 hours or you may enter the Start Time and Stop Time in the corresponding field. 5. Click Save to complete the settings. Click the Clear Schedule button to clear your settings in the table. Figure 4-84 88 TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Click the Delete Selected button to delete the selected entries in the table. 4.13 Traffic Control There are two submenus under the Traffic Control menu: Control Settings and Rules List. Click any of them, and you will be able to configure the corresponding function. The detailed explanations for each submenu are provided below. 4.13.1 Control Settings Choose menu Traffic Control Control Settings, and then you can configure the Upstream Bandwidth and Downstream Bandwidth in the next screen. The values you configure should be less than 100000Kbps. For optimal control of the bandwidth, please select the right Line Type and ask your ISP for the total bandwidth of the egress and ingress. Figure 4-85 Enable Bandwidth Control: Check this box so that the Bandwidth Control settings can take effect. Line Type: Select the right type for you network connection. If you dont know how to choose, please ask your ISP for the information. Total Upstream Bandwidth - The upload speed through the WAN port. Total Downstream Bandwidth - The download speed through the WAN port. 4.13.2 Rules List Choose menu Traffic Control Rules List, and then you can view and configure the Bandwidth Control rules in the screen below. 89 TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Figure 4-86 Description: This is the information about the rules such as address range. Upstream Bandwidth: This field displays the max and mix upload bandwidth through the WAN port, the default is 0. Downstream Bandwidth: This field displays the max and mix download bandwidth through the WAN port, the default is 0. Edit: Click Edit to modify the rule. To add/modify a Bandwidth Control rule, follow the steps below. 1. Click Add New shown in Figure 4-86, you will see a new screen shown in Figure 4-87. 2. Enter the information like the screen shown below. Figure 4-87 3. Click the Save button. 4.14 IP&MAC Binding 90 TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide There are two submenus under the IP &MAC Binding menu: Binding Settings and ARP List. Click any of them, and you will be able to scan or configure the corresponding function. The detailed explanations for each submenu are provided below. 4.14.1 Binding Settings This page displays the IP & MAC Binding Setting table; you can operate it in accord with your desire (shown in Figure 4-88). Figure 4-88 IP Address: The assigned IP address of the controlled computer in the LAN. MAC Address: The MAC address of the controlled computer in the LAN. Bound: Check this option to enable ARP binding for a specific device. Edit: To modify or delete an existing entry. When you want to add or modify an IP & MAC Binding entry, you can click the Add New button or Edit button, and then you will go to the next page. This page is used for adding or modifying an IP
& MAC Binding entry (shown in Figure 4-89). Figure 4-89 To add IP & MAC Binding entries, follow the steps below. 1. Click the Add New button as shown in Figure 4-88. 2. Enter the MAC Address and IP Address. 3. Select the Bind checkbox. 4. Click the Save button to save it. 91 TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide To modify or delete an existing entry, follow the steps below. 1. Find the desired entry in the table. 2. Click Edit as desired on the Edit column. Click the Enable/ Disable Selected button to make selected entries enabled or disabled. Click the Delete Selected button to delete selected entries. 4.14.2 ARP List To manage the computer, you could observe the computers in the LAN by checking the relationship of MAC address and IP address on the ARP list, and you could also configure the items on the ARP list. This page displays the ARP List; it shows all the existing IP & MAC Binding entries (shown in Figure 4-90). Figure 4-90 IP Address: The assigned IP address of the controlled computer in the LAN. MAC Address: The MAC address of the controlled computer in the LAN. Status: Indicates whether or not the MAC and IP addresses are bound. Load: Load the item to the IP & MAC Binding list. Click the Load Selected button to load selected items to the IP & MAC Binding list. Click the Refresh button to refresh all items. 4.15 Dynamic DNS Choose menu Dynamic DNS, and you can configure the Dynamic DNS function. The Modem Router offers the DDNS (Dynamic Domain Name System) feature, which allows the hosting of a website, FTP server, or e-mail server with a fixed domain name (named by yourself) and a dynamic IP address, and then your friends can connect to your server by entering your domain name no matter what your IP address is. Before using this feature, you need to sign up for DDNS service providers such as www.dyndns.org or www.no-ip.com. The Dynamic DNS client service provider will give you a password or key. 92 TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Figure 4-91 Service Provider: This field displays the service provider of DDNS. Domain Name: Enter the Domain name you received from dynamic DNS service provider. Username & Password: Type the User Name and Password for your DDNS account. Enable DDNS: Activate the DDNS function or not. Login/ Logout: Login to or logout of the DDNS service. 4.16 Diagnostic Choose Diagnostic, you can view the test results for the connectivity of the physical layer and protocol layer for both LAN and WAN sides in the screen. Select the desired type and click the start button. Figure 4-92 93 TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide 4.17 System Tools Choose menu System Tools, and you can see the submenus under the main menu: System Log, Time Settings, Manage Control, CWMP Settings, SNMP Settings, Backup & Restore, Factory Defaults, Firmware Upgrade, Reboot and Statistics. Click any of them, and you will be able to configure the corresponding function. The detailed explanations for each submenu are provided below. 4.17.1 System Log Choose menu System Tools System Log, and then you can view the logs of the Modem Router. Figure 4-93 Log Type: By selecting the log type, only logs of this type will be shown. Log Level: By selecting the log level, only logs of this level will be shown. Refresh: Refresh the page to show the latest log list. Clear Log: All the logs will be deleted from the Modem Router permanently, not just from the page. Save Log: Click to save all the logs in a txt file. Log Settings: Click to set the logs in the screen (shown in Figure 4-94). 94 TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Figure 4-94 Save Locally: If Save Locally is selected, events will be recorded in the local memory. Minimum Level: Select the Minimum level in the drop-down list, for the Minimum Level, all logged events above or equal to the selected level will be displayed. Save Remotely: If Save Remotely is selected, events will be sent to the specified IP address and UDP port of the remote system log server. Click the Save button to save your settings. 4.17.2 Time Settings Choose menu System Tools Time Settings, and then you can configure the time on the following screen. Figure 4-95 Time Zone: Select your local time zone from this pull down list. Date: Enter your local date in MM/DD/YY into the right blanks. Time: Enter your local time in HH/MM/SS into the right blanks. NTP Server 1 / NTP Server 2: Enter the address or domain of the NTP Server 1 or NTP Server 2, and then the Modem Router will get the time from the NTP Server preferentially. In addition, the Modem Router built-in some common NTP Servers, so it can get time automatically once it connects the Internet. To set time manually:
1. Select your local time zone. 2. Enter the Date in Year/Month/Day format. 95 TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide 3. Enter the Time in Hour/Minute/Second format. 4. Click Save. To set time automatically:
1. Select your local time zone. 2. Enter the address or domain of the NTP Server 1 or NTP Server 2. 3. Click the Get GMT button to get system time from Internet if you have connected to the Internet. 4.17.3 Manage Control Choose System Tools Manage Control, you can see the screen (shown in Figure 4-94) Figure 4-96 Current User Status: This box displays the information about User Type, User Name, Host IP Address and Host MAC Address. Account Management: Here you can set the account user information about Old Password, New User Name, New Password and Confirm Password. Service Configuration: Here you can modify the port of the Modem Routers web management interface and limit the hosts which can login this Modem Routers web management interface. 4.17.4 CWMP Settings Choose System Tools CWMP Settings, you can configure the CWMP function in the screen. The Modem Router offers CWMP feature. The function supports TR-069 protocol which collects information, diagnoses the devices automatically via ACS
(Auto-Configuration Server). the devices and configures 96 TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Figure 4-97 CWMP: Select enable the CWMP function. Inform: Enable or disable the function. If enabled, the information will be informed to ACS server periodically. Inform Interval: Enter the interval time here. ACS URL: Enter the website of ACS which is provided by your ISP. ACS User Name/Password: Enter the User Name and password to login the ACS server. Interface used by TR-069 client: Select the interface used by TR-069 client. Display SOAP messages on serial console: Enable or disable this function. Connection Request User Name/Password: Enter the User Name and Password that provided the ACS server to login the Modem Router. Connection Request Path: Enter the path that connects to the ACS server. Connection Request Port: Enter the port that connects to the ACS server. Connection Request URL: Enter the URL that connects to the ACS server. 4.17.5 SNMP Settings Choose ManagementSNMP Agent, you can see the SNMP-Configuration screen as shown below. SNMP (Simple Network Management Protocol) has been widely applied in the computer networks currently, which is used for ensuring the transmission of the management information between any two nodes. In this way, network administrators can easily search and modify the information on any node on the network. Meanwhile, they can locate faults promptly and implement the fault diagnosis, capacity planning and report generating. 97 TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Figure 4-98 An SNMP Agent is an application running on the Modem Router that performs the operational role of receiving and processing SNMP messages, sending responses to the SNMP manager, and sending traps when an event occurs. So a router contains SNMP "agent" software can be monitored and/or controlled by SNMP Manager using SNMP messages. 4.17.6 Backup & Restore Choose menu System Tools Backup & Restore, and then you can save the current configuration of the Modem Router as a backup file and restore the configuration via a backup file as shown in Figure 4-99. Figure 4-99 Click the Backup button to save all configuration settings as a backup file in your local computer. To upgrade the Modem Router 's configuration, follow these instructions. Click the Browse button to find the configuration file which you want to restore. Click the Restore button to update the configuration with the file whose path is the one you have input or selected in the blank. Note:
The current configuration will be covered with the uploading configuration file. Wrong process will lead the device unmanaged. The restoring process lasts for 20 seconds and the Modem Router will restart automatically then. Keep the power of the Modem Router on during the process, in case of any damage. 4.17.7 Factory Defaults Choose menu System Tools Factory Defaults, and then and you can restore the configurations of the Modem Router to factory defaults on the following screen 98 TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Figure 4-100 The default User Name: admin The default Password: admin The default Subnet Mask: 255.255.255.0 Click the Restore button to reset all configuration settings to their default values. Note:
All changed settings will be lost when defaults are restored. 4.17.8 Firmware Upgrade Choose menu System Tools Firmware Upgrade, and then you can update the latest version of firmware for the Modem Router on the following screen. Figure 4-101 Firmware Version: Displays the current firmware version. Hardware Version: Displays the current hardware version. The hardware version of the upgrade file must accord with the Modem Routers current hardware version. To upgrade the Modem Router's firmware, follow these instructions below:
1) Download a most recent firmware upgrade file from our website (www.tp-link.com). 2) Enter or select the path name where you save the downloaded file on the computer into the File Name blank. 3) Click the Upgrade button. 4) The Modem Router will reboot while the upgrading has been finished. Note:
99 TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide 1) New firmware versions are posted at http://www.tp-link.com and can be downloaded for free. There is no need to upgrade the firmware unless the new firmware has a new feature you want to use. However, when experiencing problems caused by the Modem Router rather than the configuration, you can try to upgrade the firmware. 2) When you upgrade the Modem Router's firmware, you may lose its current configurations, so before upgrading the firmware please write down some of your customized settings to avoid losing important settings. 3) Do not turn off the Modem Router or press the Reset button while the firmware is being upgraded. Loss of power during the upgrade could damage the Modem Router. 4) The firmware version must correspond to the hardware. 5) The upgrade process takes a few moments and the Modem Router restarts automatically when the upgrade is complete. 4.17.9 Reboot Choose menu System Tools Reboot, and then you can click the Reboot button to reboot the Modem Router via the next screen. Some settings of the Modem Router will take effect only after rebooting, which include Figure 4-102 Change the LAN IP Address (system will reboot automatically). Change the DHCP Settings. Change the Wireless configurations. Change the Web Management Port. Upgrade the firmware of the Modem Router (system will reboot automatically). Restore the Modem Router's settings to factory defaults (system will reboot automatically). Update the configuration with the file (system will reboot automatically. 4.17.10 Statistics Choose menu System Tools Statistics, and then you can view the statistics of the Modem Router, including total traffic and current traffic of the last Packets Statistic Interval. 100 TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Figure 4-103 Statistics Status: Enable or Disable. The default value is disabled. To enable it, click the Enable. If it is disabled, the function of DoS protection in Security settings will be disabled. Statistics Interval (5-60): The default value is 10. Select a value between 5 and 60 seconds in the drop-down list. The Packets Statistic interval indicates the time section of the packets statistic. Click Reset All to reset the values of all the entries to zero. Click Delete All to delete all entries in the table. Click the Refresh button to refresh immediately. Statistics Table:
IP/MAC Address The IP and MAC address are displayed with related statistics. Total Packets The total number of packets received and transmitted by the Modem Router. Bytes The total number of bytes received and transmitted by the Modem Router. Packets The total number of packets received and transmitted in the last Packets Statistic interval seconds. Bytes The total number of bytes received and transmitted in the last Packets Statistic interval seconds. ICMP Tx The number of the ICMP packets transmitted to WAN per second at the specified Packets Statistics interval. It is shown like current transmitting rate
/ Max transmitting rate. Current UDP Tx SYN Tx The number of UDP packets transmitted to the WAN per second at the specified Packets Statistics interval. It is shown like current transmitting rate
/ Max transmitting rate. The number of TCP SYN packets transmitted to the WAN per second at the specified Packets Statistics interval. It is shown like current transmitting rate
/ Max transmitting rate. Operation Reset Reset the value of he entry to zero. Delete Delete the existing entry in the table. 101 TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Appendix A: Specifications General Standards and Protocols ANSI T1.413.I2, ITU G.992.1, ITU G.992.2, ITU G.992.3, ITU G.992.5, IEEE802.1p, IEEE 802.11b,IEEE802.11e, IEEE 802.11g, IEEE 802.11n, IEEE 802.3, IEEE 802.3u, TCP/IP, PPPoA, PPPoE, SNTP, HTTP, DHCP, ICMP, NAT Safety & Emission FCC, CE Ports LEDs Four 10/100M Auto-Negotiation RJ45 portsAuto MDI/MDIX) Four RJ11 ports Two USB 2.0 ports Power, 1,,2(USB), ADSL, Line, Internet, 1,2(Phone), WLAN, WPS 1,2,3,4(LAN) Network Medium 10Base-T: UTP category 3, 4, 5 cable 100Base-TX: UTP category-5 Max line length: 6.5Km Data Rates Downstream: Up to 24Mbps Upstream: Up to 3.5MbpsWith Annex M enabled System Requirement Internet Explorer 5.0 or later, Netscape Navigator 6.0 or later Win 9x/ ME/ 2000/ XP/ Vista/ 7 Physical and Environment Working Temperature 0 ~ 40 Working Humidity 10% ~ 90% RH (non-condensing) Storage Temperature
-40 ~ 70 Storage Humidity 5% ~ 90% RH (non-condensing) 102 TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Appendix B: Troubleshooting T1. How do I restore my Modem Routers configuration to its factory default settings?
With the Modem Router powered on, press and hold the RESET button on the front panel for 8 to 10 seconds before releasing it. Note:
Once the Modem Router is reset, the current configuration settings will be lost and you will need to re-configure the router. T2. What can I do if I dont know or forget my password?
1) Restore the Modem Routers configuration to its factory default settings. If you dont know how to do that, please refer to T1. 2) Use the default user name and password: admin, admin. 3) Try to configure your Modem Router once again by following the instructions in 4.1 Login. T3. What can I do if I cannot access the web-based configuration page?
1) Configure your computers IP Address. For Windows 7 OS Go to Start > Settings >
Control Panel, and then you will see the following page. Click View network status and tasks 103 TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Click Change adapter settings Right-click Local Area Connection Click Properties 104 TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Double-click Internet Protocol Version 4
(TCP/IPv4) Select Obtain an IP address automatically Select Obtain DNS server address automatically Click OK 105 TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide For Windows Vista OS Go to Start > Settings >Control Panel, and then you will see the following page. Click View network status and tasks Click View status Click Properties 106 TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Double-click Internet Protocol Version 4
(TCP/IPv4) Select Obtain an IP address automatically Select Obtain DNS server address automatically Click OK 107 TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide For Windows XP OS Go to Start > Control Panel, you will then see the following page. Click Network and Internet Connections Click Network Connections Right-click Local Area Connection Click Properties 108 TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Double-click Internet Protocol (TCP/IP) Select Obtain an IP address automatically Select Obtain DNS server address automatically Click OK 109 TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Click OK 2) Configure your IE browser Open your IE browser, click Tools tab and you will see the following screen. Click Internet Options 110 TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Select Never dial a connection Click OK Now, try to log on to the Web-based configuration page again after the above settings have been configured. If you still cannot access the configuration page, please restore your Modem Routers factory default settings and reconfigure your Modem Router following the instructions in 4.1 Login. Please feel free to contact our Technical Support if the problem still exists. T4. What can I do if I cannot access the Internet?
1) Check to see if all the connectors are connected well, including the telephone line, Ethernet cables and power adapter. 2) Check to see if you can log on to the web management page of the Modem Router. If you can, try the following steps. If you cannot, please set your computer referring to T3 then try to see if you can access the Internet. If the problem persists, please go to the next step. 3) Consult your ISP and make sure all the VPI/VCI, Connection Type, account username and password are correct. If there are any mistakes, please correct the settings and try again. 4) If you still cannot access the Internet, please restore your Modem Router to its factory default settings and reconfigure your Modem Router by following the instructions in 4.1 Login. 5) Please feel free to contact our Technical Support if the problem still exists. Note:
For more details about Troubleshooting and Technical Support contact information, please log on to our Technical Support Website: http://www.tp-link.com/en/support T5. What can I do if I dont know how to configure USB device for USB Voice Mail function?
1) Plug an external USB hard drive or USB flash disk into the USB port labled USB 1/2 on the Modem Router. The free space of the plugged USB device should be more than 4MB. 111 TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide 2) Insert the provided Resource CD into CD-ROM drive of your computer. 3) Please select your product model and click Start Setup. 4) Then the configuration wizard will pop up and show you how to connect your devices. After that, the Easy Setup Assistant will start. Click NEXT, and then follow the step-by-step instructions. 112 TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide 5) When it comes to Configure USB Voice Mail page, check boxes before Configure USB Voice Mail and Send Files to USB Disk. Then click NEXT to continue. 6) Follow the step-by-step instructions until you comes to the finish screen. Click FINISH to close this wizard. 113 TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide 7) The configure files can be found in your USB device which means you have successfully configured the USB device for USB Voice Mail function. 114 TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Appendix C: Telephony Features This section introduces what the following features are used for. Call Holding This feature allows you to put a call on hold, in which case the call is not ended but no verbal communication is available. To put a call on hold, press the FLASH button. To return to the original call, press the FLASH button again. Call Transfer This feature allows you to redirect the current call to another phone by using the FLASH button and dialing the destination number. To transfer a call, please follow the steps below:
1. Press FLASH button to put the current call on hold. 2. Dial the destination number. Note: To quit the transfer, press the FLASH button again to return to the original call before hearing the ringback tone. 3. Hang up when hearing the ringback tone or wait for the newly called party to answer and then hang up. Now the call is successfully transferred. Call Waiting With this feature enabled, if a calling party places a call to you while you are busy, you are able to suspend the current call and switch to the new incoming call. To switch to the new incoming call, press FLASH followed by the number 2. The first call will be automatically put on hold. You can switch between the two calls by pressing FLASH followed by the number 2. USB Voice Mail With this feature enabled, the caller will be prompted to leave a voice message upon the call or when there is no response for a certain time. Call Forwarding This feature allows an incoming call to be redirected to a specified party. There are three call forwarding features, including Call Forwarding Unconditionally, Call Forwarding on Busy and Call Forwarding on No Answer. With Call Forwarding Unconditionally enabled, no matter whether the called party is busy or not, the incoming call will be redirected to the specified party. With Call Forwarding on Busy enabled, the incoming call will be redirected to the specified party when the called party is busy. With Call Forwarding on No Answer enabled, the incoming call will be redirected to the specified party when there is no response for a certain time. Anonymous Calling This feature allows you to make a call without your phone number or ID being displayed on the called party's phone. 115 TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Anonymous Call Blocking With this feature enabled, all anonymous calls will be blocked. Speed Dial This feature allows you to create short numbers for your frequently used telephone numbers to make your dialing more convenient. You just need to press one or two digits and the key # instead of the original phone number to make a call. Warm Line With this feature enabled, a call will be automatically directed to a specified party without taking any additional action when the phone goes off-hook for a certain time. To use this feature, you need to set warm line numbers first on the web management page. DND (Do Not Disturb) With this feature enabled, all the incoming calls will be blocked and the caller will hear the busy tone. Three-way Call This feature allows three people to communicate at the same time. To set up a three-way call, please follow the steps below:
1. Press the FLASH button to put the first call on hold. 2. Dial the destination number. 3. Wait for the third party to answer and then press FLASH followed by the number 3. Now the three-way call is successfully set up. 4. To drop yourself out of the call, simply hang up. A three-way call can also be set up during a call with Call Waiting enabled. When hearing the call waiting tone during a call, press FLASH followed by the number 3. Note: The call will end if the initiator of the three-way call hangs up. However, the call will not end if anyone of the other two parties hangs up. The left two parties remain connected to each other. 116 TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Appendix D: Telephone Operation The table below guides you to configure some frequently used call features using keypads on your telephone. For the features mentioned in this table, please refer to Telephony Features in Appendix C. Code Description Usage
*20 to Listen messages stored your USB device. voice in storage
*60 Disable Call Waiting.
*61 Enable Call Waiting.
*62
*63 With Call Waiting enabled, disable it for the call you are going to make. With Call Waiting disabled, enable it for the call you are going to make.
*99 Enable Redial on busy. Pick up the phone to dial this code and then follow the voice prompts for the operations below:
Press 0 to listen to new messages. Press 1 to listen to the previous message. Press 2 to listen to the current message again. Press 3 to listen to the next message. Press 4 to delete the current message. Pick up the phone to dial this code. After hearing the confirmation tone, hang up to make the configuration take effect. Pick up the phone to dial this code. After hearing the confirmation tone, hang up to make the configuration take effect. Pick up the phone to dial this code. You will hear the confirmation tone and then the dial tone which will prompt you to dial the destination number. Pick up the phone to dial this code. You will hear the confirmation tone and then the dial tone which will prompt you to dial the destination number. Pick up the phone to dial this code. You will hear the confirmation tone and then the dial tone which will prompt you to dial the destination number. If the called party is busy, the number will be dialed again and again until there is response. To end the dialing, hang up and then pick up your phone.
*70
*71 Disable all forwarding features. the call Pick up the phone to dial this code. After hearing the confirmation tone, hang up to make the configuration take effect. Enable Call Forwarding on No Answer. Pick up the phone to dial this code. After hearing the confirmation tone, hang up to make the configuration take 117 TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide effect.
*72 Enable Call Forwarding on Busy. Pick up the phone to dial this code. After hearing the confirmation tone, hang up to make the configuration take effect.
*73
*69
*68 Enable Call Forwarding Unconditionally. Pick up the phone to dial this code. After hearing the confirmation tone, hang up to make the configuration take effect. Dial the last incoming number. Pick up the phone to dial this code. The last incoming number will be dialed automatically. Dial the last outgoing number. Pick up the phone to dial this code. The last outgoing number will be dialed automatically.
*78 Enable Warm Line.
*79 Disable Warm Line. Pick up the phone to dial this code. After hearing the confirmation tone, hang up to make the configuration take effect. Pick up the phone to dial this code. After hearing the confirmation tone, hang up to make the configuration take effect.
*80 Enable Call Blocking. Anonymous Pick up your phone to dial this code. After hearing the confirmation tone, hang up to make the configuration take effect.
*81 Disable Call Blocking. Anonymous Pick up the phone to dial this code. After hearing the confirmation tone, hang up to make the configuration take effect.
*82
*90 Anonymous With disabled, Calling enable it for the call you are going to make. Anonymous With Calling enabled, disable it for the call you are going to make. Pick up the phone to dial this code. You will hear the confirmation tone and then the dial tone which will prompt you to dial the destination number. Pick up the phone to dial this code. You will hear the confirmation tone and then the dial tone which will prompt you to dial the destination number.
*83 Enable Calling. Anonymous Pick up the phone to dial this code. After hearing the confirmation tone, hang up to make the configuration take effect.
*84 Disable Calling. Anonymous Pick up the phone to dial this code. After hearing the confirmation tone, hang up to make the configuration take effect.
*86 Enable DND (Do Not Pick up the phone to dial this code. After hearing the 118 TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Disturb). confirmation tone, hang up to make the configuration take effect.
*87 Disable DND (Do Not Disturb). Pick up the phone to dial this code. After hearing the confirmation tone, hang up to make the configuration take effect. 119 TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Appendix E: Technical Support Technical Support For more troubleshooting help, go to:
http://www.tp-link.com/en/support/faq To download the latest Firmware, Driver, Utility and User Guide, go to:
http://www.tp-link.com/en/support/download For all other technical support, please contact us by using the following details:
Global Tel: +86 755 26504400 E-mail: support@tp-link.com Service time: 24hrs, 7 days a week UK Tel: +44 (0) 845 147 0017 E-mail: support.uk@tp-link.com Service time: 24hrs, 7 days a week Turkey Tel: 444 19 25 (Turkish Service E-mail: support.tr@tp-link.com Service time: 9:00 AM to 9:00 PM 7 days a week Ukraine Tel: 0-800-505-508 E-mail: support.ua@tp-link.com Service time: Monday to Friday 14:00 PM to 22:00 PM Brazil Toll Free: 0800-770-4337 (Portuguese Service) E-mail: suporte.br@tp-link.com Service time: Monday to Saturday 08:00 AM to 08:00 PM France Tel: +33 (0) 820 800 860 (French service) Email: support.fr @tp-link.com Fee: 0.118 EUR/min from France Service time: Monday to Friday 9:00 AM to 6:00 PM (Except French Bank holidays) Russian Federation Tel: 8 (499) 754-55-60 8 (800) 250-55-60 (toll-free call from any RF region) E-mail: support.ru@tp-link.com Service time: From 10:00 to 18:00
(Moscow time)
*Except weekends and holidays Russian Federation Switzerland Tel: +41 (0) 848 800998 (German Service) E-mail: support.ch@tp-link.com Fee: 4-8 Rp/min, depending on rate of different time Service time: Monday to Friday 9:00 AM to 6:00 PM. GMT+ 1 or GMT+ 2
(Daylight Saving Time) Singapore Tel: +65 62840493 E-mail: support.sg@tp-link.com Service time: 24hrs, 7 days a week USA/Canada Toll Free: +1 866 225 8139 E-mail: support.usa@tp-link.com Service time: 24hrs, 7 days a week Australia & New Zealand Tel: AU 1300 87 5465 NZ 0800 87 5465 E-mail: support@tp-link.com.au Service time: 24hrs, 7 days a week Italy Tel: +39 0230519020 E-mail: support.it@tp-link.com Service time: Monday to Friday 9:00 AM to1:00PM, 2:00PM to 6:00 PM Indonesia Tel: (+62) 021 6259 135 E-mail : support.id@tp-link.com Service time : Monday to Friday 9:00 -12:00; 13:00 -18:00
*Except public holidays Malaysia Tel: 1300 88 875465 (1300 88TPLINK) Email: support.my@tp-link.com Service time: 24hrs, 7 days a week Poland Tel: +48 (0) 801 080 618 / +48 22 7217563 (if calls from mobile phone) E-mail: support.pl@tp-link.com Service time: Monday to Friday 9:00 AM to 5:00 PM. GMT+1 or GMT+2
(Daylight Saving Time) Germany / Austria Tel: +49 1805 875465 (German Service)
+49 1805 TPLINK E-mail: support.de@tp-link.com Fee: 0.14 EUR/min from the German fixed phone network and up to 0.42 EUR/min from mobile phone Service time: Monday to Friday 9:00 AM to 6:00 PM. GMT+ 1 or GMT+ 2
(Daylight Saving Time in Germany)
*Except bank holidays in Hesse in 120
| frequency | equipment class | purpose | ||
|---|---|---|---|---|
| 1 | 2012-12-22 | 2412 ~ 2462 | DTS - Digital Transmission System | Original Equipment |
| app s | Applicant Information | |||||
|---|---|---|---|---|---|---|
| 1 | Effective |
2012-12-22
|
||||
| 1 | Applicant's complete, legal business name |
TP-Link Technologies Co., Ltd.
|
||||
| 1 | FCC Registration Number (FRN) |
0013661145
|
||||
| 1 | Physical Address |
Building 24 (floors 1,3,4,5) and 28 (floors1-4)
|
||||
| 1 |
Shenzhen, N/A 518057
|
|||||
| 1 |
China
|
|||||
| app s | TCB Information | |||||
| 1 | TCB Application Email Address |
h******@acbcert.com
|
||||
| 1 | TCB Scope |
A4: UNII devices & low power transmitters using spread spectrum techniques
|
||||
| app s | FCC ID | |||||
| 1 | Grantee Code |
TE7
|
||||
| 1 | Equipment Product Code |
TDVG3631
|
||||
| app s | Person at the applicant's address to receive grant or for contact | |||||
| 1 | Name |
J****** H********
|
||||
| 1 | Title |
Regulatory Compliance Manager
|
||||
| 1 | Telephone Number |
75521********
|
||||
| 1 | Fax Number |
75526********
|
||||
| 1 |
c******@tp-link.com
|
|||||
| app s | Technical Contact | |||||
| 1 | Firm Name |
Bureau Veritas Consumer Products Services(H.K.)Ltd
|
||||
| 1 | Name |
R**** H********
|
||||
| 1 | Physical Address |
81-1,Lu Laio Keng, 9th Ling Wu Lung Tsuen, Chiung
|
||||
| 1 |
Hsinchu Hsien, 307
|
|||||
| 1 |
Taiwan
|
|||||
| 1 | Telephone Number |
886-3******** Extension:
|
||||
| 1 | Fax Number |
886-3********
|
||||
| 1 |
r******@te.bureauveritas.com
|
|||||
| app s | Non Technical Contact | |||||
| n/a | ||||||
| app s | Confidentiality (long or short term) | |||||
| 1 | Does this application include a request for confidentiality for any portion(s) of the data contained in this application pursuant to 47 CFR § 0.459 of the Commission Rules?: | Yes | ||||
| 1 | Long-Term Confidentiality Does this application include a request for confidentiality for any portion(s) of the data contained in this application pursuant to 47 CFR § 0.459 of the Commission Rules?: | No | ||||
| if no date is supplied, the release date will be set to 45 calendar days past the date of grant. | ||||||
| app s | Cognitive Radio & Software Defined Radio, Class, etc | |||||
| 1 | Is this application for software defined/cognitive radio authorization? | No | ||||
| 1 | Equipment Class | DTS - Digital Transmission System | ||||
| 1 | Description of product as it is marketed: (NOTE: This text will appear below the equipment class on the grant) | 300Mbps Wireless N VoIP ADSL2+ Modem Router | ||||
| 1 | Related OET KnowledgeDataBase Inquiry: Is there a KDB inquiry associated with this application? | No | ||||
| 1 | Modular Equipment Type | Does not apply | ||||
| 1 | Purpose / Application is for | Original Equipment | ||||
| 1 | Composite Equipment: Is the equipment in this application a composite device subject to an additional equipment authorization? | No | ||||
| 1 | Related Equipment: Is the equipment in this application part of a system that operates with, or is marketed with, another device that requires an equipment authorization? | No | ||||
| 1 | Grant Comments | Power Output listed is the maximum combined conducted output power. The antenna(s) used for this transmitter must be installed to provide a separation distance of at 20 cm from all persons and not be co-located with any other transmitters except in accordance with FCC multi-transmitter product procedures. The Device contain 2x2 Spatial Multiplexing MIMO configuration and has 20 MHz and 40 MHz Bandwidth modes enabled for 2.4GHz band operations as described in this filing. End -users must be informed of the operating requirements for satisfying body-worn RF exposure compliance. | ||||
| 1 | Is there an equipment authorization waiver associated with this application? | No | ||||
| 1 | If there is an equipment authorization waiver associated with this application, has the associated waiver been approved and all information uploaded? | No | ||||
| app s | Test Firm Name and Contact Information | |||||
| 1 | Firm Name |
Bureau Veritas CPS (H.K.) Ltd. Taoyuan Branch
|
||||
| 1 | Name |
R******** C****
|
||||
| 1 | Telephone Number |
886-3******** Extension:
|
||||
| 1 | Fax Number |
886 3********
|
||||
| 1 |
r******@tw.bureauveritas.com
|
|||||
| Equipment Specifications | |||||||||||||||||||||||||||||||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| Line | Rule Parts | Grant Notes | Lower Frequency | Upper Frequency | Power Output | Tolerance | Emission Designator | Microprocessor Number | |||||||||||||||||||||||||||||||||
| 1 | 1 | 15C | MO | 2412.00000000 | 2462.00000000 | 0.1860000 | |||||||||||||||||||||||||||||||||||
some individual PII (Personally Identifiable Information) available on the public forms may be redacted, original source may include additional details
This product uses the FCC Data API but is not endorsed or certified by the FCC