WARNING:pdfminer.pdfpage:The PDF <_io.BufferedReader name='/Volumes/Scratch/Incoming/eg-scratch/6685191.pdf'> contains a metadata field indicating that it should not allow text extraction. Ignoring this field and proceeding. Use the check_extractable if you want to raise an error in this case UBN2310 GPON Safety Manual UBN2310 Safety Manual IMPORTANT:
Read these instructions before using the device. SAFETY NOTICES DECLARATION OF CONFORMITY Do not use this device in a humid space, in the rain or near splashing water. Do not install during thunder or lightning storms. For operation within the 5.15~5.25GHz and 5.47~5.725GHz frequency ranges, this device is restricted to indoor environments. Do not cover any ventilation openings in the device housing. Do not place the device near heat sources such as radiators or stoves. Clean the device with a clean, dry cloth. Do not use liquid or chemical cleaners. Disconnecting the device: If the device becomes damaged or encounters some other abnormality, disconnect the power plug from the AC wall outlet immediately. The device should be installed in a location not to exceed the maximum temperature of 40 Celsius (104 Fahrenheit). Keep the device away from children and pets. This equipment is not suitable for use in locations where children are likely to be present. Do not modify or attempt to disassemble the device. Use it only according to the instructions. Place the device on a cool surface. Failure to do so may result in overheating which can cause signicant damage. Product information is located on the bottom panel of the apparatus. Do not dispose of the device in a trash container. Please recycle. This product is intended to be supplied by a Listed Power Adapter or DC power source marked L.P.S." (or "Limited Power Source"), rated 12 Vdc, 2A minimum, Tma = 40 degree C minimum. If need f u r t h e r a ss i st a n ce, p l e a s e co n t a c t H O N L I N Technology Co., Ltd. for further information. Use only a Laser Class 1 optical transceiver:
CLASS 1 LASER PRODUCT & IEC 60825-1:2014 Complies with FDA performance standards for laser products except for conformance with IEC 60825-1 Ed. 3, as described in Laser Notice No. 56, dated May 8, 2019. Caution Use of controls or adjustments or performance of procedures other than those specied herein may result in hazardous radiation exposure. Manufacturer:
Ubee Interactive Holding Corp. Taiwan Branch 10F-1, No. 5 Taiyuan 1st St. Jhubei City, Hsinchu County 302, Taiwan UBN2310 Safety Manual INSTALLATION INSTRUCTIONS 1. Plug one end of a ber optic cable into the green PON (passive optical network) port on the rear panel of the device. The connector will click into place when properly installed. Plug the other end into the optical wall outlet. WARNING: Do not look directly into the optical cable end or directly into the PON port as eye injury may occur. 2. For telephone service, connect one end of another RJ-11 phone cable (not included) to one of the grey PHONE ports. Connect the other end of the cable to the RJ-11 port of an analog telephone. Note that voice service must be provisioned by your service provider. 3. Connect an Ethernet cable (not supplied) to one of the yellow LAN (Ethernet) ports on the back panel of the modem and connect the other end to the Ethernet port of a PC. Use a Category 5e or Category 6 Ethernet cable. A PC should be connected initially for device installation and conguration. 4. Connect the power adapter (supplied) to the POWER port. Connect the other end to a power outlet. 5. Turn the modem on by pressing the ON/OFF button the rear panel. 2 Analog Phone 3 1 Computer Optical Outlet 4 Power Outlet RJ-11 RJ-45 FIBER 5 ON/OFF UBN2310 Safety Manual Federal Communication Commission (FCC) Interference Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment o and on, the user is encouraged to try to correct the interference by one of the following measures:
Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. FCC Caution: Any changes or modications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Operation in the 5.15-5.25GHz band is restricted to indoor usage only. Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20 cm between the radiator & your body. FCC regulations restrict the operation of this device to indoor use only. The operation of this device is prohibited on oil platforms, cars, trains, boats, and aircraft, except that operation of this device is permitted in large aircraft while ying above 10,000 feet. Operation of transmitters in the 5.925-7.125 GHz band is prohibited for control of or communications with unmanned aircraft systems.